Scribd
Upload
255 views

DLC32 Firmware Programming Instructions

The document provides instructions for updating the firmware of the DLC32 motherboard. It is a simple 3 step process: 1. Install the MKSlaserTool software and CH340 driver (if needed). 2. Open the software, connect the DLC32 motherboard, select the firmware file and set parameters like speed and serial port. 3. The software will update the firmware and notify when complete. The motherboard needs to be restarted to use the new firmware. Troubleshooting tips and links to download firmware files or get support are also provided.

Uploaded by

Alfredo Martinez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
255 views

DLC32 Firmware Programming Instructions

The document provides instructions for updating the firmware of the DLC32 motherboard. It is a simple 3 step process: 1. Install the MKSlaserTool software and CH340 driver (if needed). 2. Open the software, connect the DLC32 motherboard, select the firmware file and set parameters like speed and serial port. 3. The software will update the firmware and notify when complete. The motherboard needs to be restarted to use the new firmware. Troubleshooting tips and links to download firmware files or get support are also provided.

Uploaded by

Alfredo Martinez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

DLC32 firmware programming instructions-V1.

The purpose of this document is to explain that the process for customers to update
the firmware of the DLC32 motherboard is simpler and easier to understand

Software Installation
1.Install “MKSlaserTool-setup V1.x.x”

1
2. Install CH340 driver file (if your PC has already been installed, please skip this
link)

NOTE:If the PC has not installed ch340, the motherboard connected to the PC cannot be
recognized and connected to DLC32

2
Software programming operation process

1. Open the MKS LASER TOOL software and connect DLC32 to the PC

2. Set DLC32 parameters

3
Parameter setting
SPI SPEED: 80MHZ
FLASH SIZE: 8MB
Baud rate: 115200

Serial port (COM): This assigns the com of the motherboard according to the PC. This is after the
CH340 driver file is installed in the previous step, the motherboard will be allocated. The
motherboard in the picture is assigned “COM15”. If you don’t know the serial number, you can
check it in the device manager.
(Note: The serial number is not fixed, if you connect to another PC, this may change)

3. Select DLC32 motherboard firmware to update

4
The process is shown in the picture above. When the software shows that the update is successful,
you only need to unplug the USB cable and power on again.

NOTE:FAQ about the bin file used for DLC32 firmware update

Q1:Where can I download the firmware?


A1:You can go to our MKS github to download.
(https://github.com/makerbase-mks/MKS-DLC32/tree/main/firmware)

Q2:Which firmware is suitable for my machine?


A2:According to your DLC32 package . TS24 SUIT or TS35 SUIT (if you buy a single motherboard,
you can choose at will). Then select the corresponding function (cnc or laser), after finding the
corresponding file, download the update

If there is any problem during use. You can leave a message on our github or facebook.

FACEBOOK:https://www.facebook.com/Makerbase.mks/
GITHUB:https://github.com/makerbase-mks/MKS-DLC32
AliExpress:https://www.aliexpress.com/store/1047297

You might also like