VIN AND ENGINE SERIAL NUMBER LOCATION

FOREWORD： The VIN and/or engine serial number are used to register
Thanks for your purchasing this motorcycle. the motorcycle．They are also use to assist your dealer
With the help of this manual, you will learn the correct when ordering parts or special service information.
procedures of operation and basic knowledge of maintenance
and trouble shooting of the motorcycle. It presents all
the basic knowledge of maintenance and trouble shooting
of the motorcycle. It presents all the details of the
performance of this motorcycle to you and the vehicle will
make your life more relaxed and happier.
In case any picture does not agree with the vehicle
physically, the latter shall prevail.

CAUTION．NOTE and MAIN POINTS carry special mean-

ings and should be carefully reviewed．

!CAUTION ：The personal safety of the rider may be

involved，disregarding this information could result in
injury to the rider．

NOTE ：These instructions point out special service

procedures or precautions that must be followed to
avoid damaging the machine． The VIN is stamped on the front main beam of the frame．
The engine serial number is stamped on the rear end
MAIN POINTS ： This provides special information to make
of the crankcase assembly
maintenance easier or important instructions clearer． VIN. :

Engine No.:

-1-

Downloaded from www.Manualslib.com manuals search engine

 NOTES FOR SAFE RIDING
CONTENTS
RIDING APPAREL
NOTES FOR SAFE RIDING……………………………2 1.Loose，fancy clothing can be uncomfortable and unsafe
when riding your motorcycle ． Choose good quality
LOCATION OF PARTS…………………………… …4 motorcycle riding apparel when riding your motorcycle．
2. most motorcycle accident fatalities are due to head
INSTRUMENT PANEL…………………………… ……7 injuries. ALWAYS wear a helmet, a face shield or goggles
as well as boots, gloves and protective clothing. so does
USING METHODS OF SWITCHES……… ……………8 the passenger on your motorcycle.
3. the exhaust system must be very hot while you are riding,
USING METHODS OF TRUNK…………………………10 and even remains so after the engine operation stops, so
never touch any part of the hot exhaust
ADD GASOLINE AND ENGINE OIL……………………11

CORRECT DRIVING OPERATIONS……………………12

INSPECTION BEFORE RIDING………………………20

PERIODICAL INSPECTIONS…………………………23

SIMPLE MAINTENANCE METHODS …………… … 26

SPECIFICATIONS……………………………… … 30

ELECTRICAL DIAGRAM……………………… ……31

-2-

Downloaded from www.Manualslib.com manuals search engine

 RULES FOR SAFE DRIVE MODIFICATION
Check must be conducted before starting the engine to any modification of the motorcycle or removal of the
prevent mishaps and damage to components. original equipment may render the vehicle unsafe or illegal
Only the qualified person who has passed the drive P1ease obey all the national and local equipment
examination with a drive license is permitted to drive the regulations.
vehicle but not anybody else without a drive license.
Full preoccupation is required during drive, paying
attention to the following points to avoid any possible hurt DO NOT OVERLOAD
to you by other motorized vehicles: 1. Do not load on the places where they are not allowed．
Do not drive too close to other vehicles; 2.Do not put cotton or other same items near the engine
Never contend for lane. or the exhaust pipe, When the motorcycle is in the
Strictly observe the local traffic rules. over-loading condition, its stability, security and speed
As driving at overspeed is the cause of many accidents. will be affected.
Do not drive at a speed that the actual situation does not
permit.
Particular care should be exercised at the level
crossing of roads, entrance and exit of parking lot or on
the automobile lane.
During drive, grasp the left handlebar by the left hand
and the throttle twist grip by the right hand, with feet on
the footrests.

-3-

Downloaded from www.Manualslib.com manuals search engine

 LOCATION OF PARTS

-4-

Downloaded from www.Manualslib.com manuals search engine

 -5-

Downloaded from www.Manualslib.com manuals search engine

 1.Ignition switch/stolen-prevention lock
2.Electric starter switch
3.Lamp switch
4.Handlebar
5.Front brake lever
6.Right mirror
7.Fuel level indicator
8.The turn signals
9.speedometer
lO.Left mirror
11.Switch to change the far and near light
12.Rear brake lever
13.Turn signals switch
l4.Horn button

-6-

Downloaded from www.Manualslib.com manuals search engine

 INSTRUMENT PANEL
HOW TO USE THE INSTRUMENT PANEL MAIN POINTS
1. The indicator will stop at E position when the
ignition switch is turned to OFF position.
2. place the motorcycle on the center stand to read
the number of the left fuel.

④THE TURN SIGNALS

Turn the switch to“LEFT”or“RIGHT”position，the
turn signal will flash to advise the driver．

⑤THE FAR LIGHT INDICATOR

The indicator will be lit when the change light
switch turned to FAR LIGHT position．

①SPEEDOMETER
The speedometer indicates the road speed in kilometers
per hour.

②ODOMETER
The odometer registers the total distance that the
motorcycle has been run (The minimum number is O．1km)You
should change the engine oil and check the motorcycle
periodically according to it．

③FUEL GAUGE
The‘‘E’’mark indicates the fuel tank is empty or nearly
so．

-7-

Downloaded from www.Manualslib.com manuals search engine

 USING METHODS OF THE SWITCHES
THE IGNITION SWITCH
The ignition switch control the start，the wiring
diagram for lights and the lock for the handlebars．
Please take the key with you when yon leave your
motorcycle．
(ON)it is connected．
1.You can start the engine．
2.You can drive
3.You can not take the key down
(OFF)it is shut down．
1·You can not start the engine．
2·The engine is stopped． THE KEY TO THE HANDLE BARS
3·You can take the key down or put the key in . Please lock the handlebar lock when you 1eave the
(LOCK)it is locked． motorcycle to avoid to avoid to be stolen．
1.The handlebar are 1ocked，you cannot change directions． (1)turn the handlebar to the left
2.You can take the key down or put the key in. (2)put the key in from OFF position，press and turn
to LOCK position．
(3)take the key down．
Do not press when you want to open the lock, it will
be all right to turn the key，from LOCK position to OFF
Position.

-8-

Downloaded from www.Manualslib.com manuals search engine

 MAIN POINTS
1.If it is hard to lock，you can turn the handlebar
to the right a little and then lock it.
MAI N POINTS
2.Shake the handlebars left and right to be sure that
it has been locked. Do not use the horn if un- necessary.

THE CHANGEABLE SWITCH FOR

THE TURN SIGNALS THE FRONT LIGHT

Use this switch，you can change the light direction
of the front lamp．
HI：the high beam
LO：the low beam
MAI N POINTS
When there are cars before you or coming towards you
in the night, please use the LO switch．
THE START SWITCH
This Switch is to start the engine
Use the turn signals when you want to turn to the 1eft Turn the switch to ON position and squeeze the brake
or the right． lever．meanwhile press the starting button and the engine
R：the right turn signal will flash． will be started．
L：the left turn signal will flash．
NOTE
MIDDLE：the turn signal will not flash．
After you have finished， please turn off the turn If the engine call not be started in 3 seconds, please
signals． use the kick starter to stare the engine to avoid emptying
the battery. Then check the starting system.

THE HORN BUTTON THE FRONT LAMP SWITCH

Press the horn button，the horn will loud. Light switch

-9-

Downloaded from www.Manualslib.com manuals search engine

 The front light switch has three positions, OPEN THE TRUNK
And “●”(a white point). Open the seat when you want use the trunk or put the
When the switch is in this position, the front helmet in it.
head light ,tail and meter lights are all lit up. 1.put the ignition key in the lock of the seat and turn
When the switch is in this position,the tail, to the right.
betraying and meter Lights are lit up. 2.Hold the seat from the back up and open the seat.
“●”When it is in this position. The front illuminator, 3.Press the seat and the lock will be closed auto-
tail, betraying and meter lights are all off. matically.

MAIN POINTS NOTE

After the engine is started by pressing the ignition 1.Hold the seat up slightly to see if the lock is
switch, you can inspect the wiring diagram for the lights. closed.
2.If you press the seat when the ignition key in the
trunk, you can not take the key out, so please pay much
attention to this.
USING METHODS OF THE TRUNK 3.Do not keep such items as cotton on any place under
the seat except the trunk.

- 10 -

Downloaded from www.Manualslib.com manuals search engine

 MAIN POINTS
1.The trunk load capacity is 10kg．
2.Do not keep heat- Sensitive item in trunk when the
trunk may get hot．
3.Do not keep valuable and easily damaged items in the
trunk．
4.Keep the easily—flown items first in the plastic
bag then put them in the trunk.
5.Do not allow water to get inside when the washing
the motorcycle． CHANGE ENGINE OIL
6.Do not clean the trunk with water. Change the engine oil after the first 300km
riding．Afterwards，change it every 1000km，check the volume
ADD GASOLINE AND ENGINE OIL every 500km riding and add it to the standard volume in
time．The full volume is 0.9L and the replace volume is
ADD GASOLINE 0.75L．
There is a gasoline tank gate at the rear part of the
seat ， open it with the ignition key , take down the CHANGE GEAR OIL
cover．add unleaded gasoline with an octane rating of 90 Change the gear oil after the first 300km and every 5000km
or higher. successively or every half a year, whichever comes first.
check the capacity every 500km.pls use SAE80W90 gear oil.
ENGINE OIL The volume of the gear oil
There are several reasonable effects included in the Full volume．O.11L
engine oil with high quality．only the high degreasing
4-strokeSAEl0W-30(SIGMA)engine oil can ensure this
requirement or even exceed it．Do not need to use other
additives ． Yon can use the HQB-10 engine oil instead
according to the condition of our marketing service．
Mucosity：The mucosity of engine oil is to be decided
according to the humidity of local climate．
- 11 -

Downloaded from www.Manualslib.com manuals search engine

 - 12 -

Downloaded from www.Manualslib.com manuals search engine

 NOTE
1. Don’t fill oil prior to the FULL level when adding CORRECT DRIVING OPERATIONS
oil.
2.The engine will be easily damaged when driving STARTING METHOD OF THE ENGINE
without oil.
3.Don’t mix oil with other type of oil and it will BEFORE STARTING
affect the performance of the engine.
1.You must check the volume of oil and gasoline.
4.Wipe off the oil outside the engine.
2.Place the motorcycle on the center stand．
5.Close the cover of the oil tank.
3.Start the engine at left side of the motorcycle．
6.Don’t put cotton on the oil tank to avoid keeping
the oil back or damaging the engine. [1]Turn the ignition switch to ON position Please
inspect the motorcycle according to the following
items：
! CAUTION 1.If the ignition switch has been on ON position．
Please pay much attention to the following items when
2.Inspect if the front lamp and the rear lamp lit or not．
Adding gasoline or oil to the engine.
3.If a11 the switches are functional or not．
1.Shut off the engine and turn the ignition switch to
4.If the horn is functional when pressing the horn button．
OFF.
5.If the horn is un—functional ． perhaps the fuse is
2.Fire is forbidden and do not add oil beside fire and
broken，Please refer to page 33
smoke.
After you have done the above inspections，please go to
3.Add gasoline of oil on a plat place.
dealer’s service station if the lights or the horn are
4.Don’t add gasoline too much to avoid it coming out.
still un-functional．
5.Don’t make dirt into the gasoline tank.
6.Close the cover of the oil tank.
7.Wipe off the gasoline outside the gasoline tank.
Forbid to store gasoline at home since it is very
dangerous.

- 13 -

Downloaded from www.Manualslib.com manuals search engine

 MAIN POINTS
The electric start will be un-functional if the brake
levers are not squeezed．
[3]Don’t rotate the throttle handlebar when
pressing the start button．

[2]Hold the front and rear levers

MAIN POINTS
1.After the engine is ignited，please release the
start button to avoid affecting the engine．
2.To avoid empty the battery，please use the kick
starter to start the engine after 3 seconds by the electric
start or and then check the starting system.
3.Please rotate the throttle handlebar 1/8-1/4round
and then start the engine again if you can not ignite the
engine 2 or 3 times. Return the throttle handlebar after
ignition.

- 14 -

Downloaded from www.Manualslib.com manuals search engine

 First confirm the following items then start again.
[1]Turn the ignition switch to ON position.

[2]Hold the rear brake lever with the left hand and press
the front part of the seat with the right hand.

[4] Preheat the engine while it is cool. [3]Kick the kick starter with the right foot.

！CAUTION
Don’t preheat the engine in a close room because of
the noxious gas such as co in the waste gas.
MAIN POINTS
1 .If the engine is cool，warm it after it is started.
2．The engine will be difficultly started when the fuel
runs out and added again or it has been stored for a long
time . At this time do not rotate the throttle bar and start
the engine for several times． (recommend starting by the
kick starter)．After the gasoline is burnt，water will be
producted and leave in the exhaust pipe．so in the cold
areas，note the problem of water becoming ice．
When the battery is out and can not start by the electric
starter

- 15 -

Downloaded from www.Manualslib.com manuals search engine

 Know well about the correct driving way.
It is good not only for security，but also for the using
[2]THE PROCEDURE TO DRIVE MOTORCYCLE
life of your motorcycle．saving fuel and oil．
Hold the handlebars with both hands, sit on the seat
METHOD OF STARTING from the left．At this time.
The left foot stand on the ground squeeze the rear brake
[l]RELEASE THE CENTER STAND lever．

NOTE
After starting the engine，hold the rear brake lever
with left Hand and push the motorcycle for ward with the Don’t rotate the throttle handle bar before
right hand to release the center stand.
starting．
NOTE
Please hold the back dress holder when you release or [3] OBSERVE IF THE SURROUNDING IS SAFE
place the Center stand．do not hold the back part of the Before starting, you should give on information using
seat． the left turning signal to observe if the surroundings is
safe or not. Squeeze the rear brake at this time.

- 16 -

Downloaded from www.Manualslib.com manuals search engine

 NOTE
If rotate the handlebar Of throttle too much，it may
make the motorcycle run for-ward suddenly．
ADJUST SPEED
Adjust speed through rotating the handlebar of throttle．

NOTE

Note the cars from the back．

[4] START
Loosen the brakes and rotate the handlebar of throttle
to make the motorcycle start gradually.

Rotate accelerate ， it is better to rotate slowly

Return，It is better to return quickly
USING METHOD OF THE BRAKES
It is better to use the front and rear brake together．

- 17 -

Downloaded from www.Manualslib.com manuals search engine

 BE EXTRA SAFETY CONSCIOUS ON BAD WEATHER DAYS
Riding on bad weather days ， especially wet ones
requires extra Caution．Braking distance double on a rainy
day．Stay off of the painted surface marks，manhole covers
and greasy appearing areas as they can be especially
slippery． Use extreme Caution at railway crossings and
on metal gratings and bridges. Whenever in doubt about road
1.Squeeze the brake levers after quick returning the conditions，slow down!
throttle bar.
2.Gradually shut the motorcycle and make the speed low
is the most proper way to use the brakes． PAY ATTENTION TO WORKING CONDITION OF

THE BRAKES AFTER WASHING OR DRIVING IN

NOTE
It is very dangerous if use only the front brake or WATER
the rear brake．It may make the motorcycle slip．
The function Of the brake will be affected after
washing or driving in water．Drive slowly until the brake
DON’T BRAKE OR TURN SUDDENLY become normal．
It is extremely dangerous to brake or turn in a sudden,
it may make the motorcycle slip or turn over
CORRECT WAY TO PARK THE MOTORCYCLE
[1]give signals
First use the turn signals to inform others and then
drive to the sides of the road．

- 18 -

Downloaded from www.Manualslib.com manuals search engine

 Return the throttle and squeeze the front and rear
brake levers. At the same time, the brake indicator is lit
to inform the following drivers. [3] Place the motorcycle on the center stand
place the motorcycle on the center stand on the place
where does not affect traffic .
1.Ho1d the handlebar with the left hand and hold the
tail part with the right hand．
[2] Turn the ignition key to OFF position. 2.Press the lever of the center sand with the right
foot and take the motorcycle up with the right hand.

Shut off the turn signals and turn the ignition key to OFF
position after parking well the motorcycle.

NOTE
Don’t park the motorcycle on the soft ground or on
a slope.
[4] Lock the turning bar
To avoid stolen. Please lock the steering and bring the key
with you when you leave.

- 19 -

Downloaded from www.Manualslib.com manuals search engine

 BREAK IN Check the following items before going to service
Proper break-in is important to achieve maximum life station．
and performance from your motorcycle． The engine can not be started?
1.The first month or the first 1000 km drive Check the following items again：
with in 45km／h． 1.If there is fuel in the engine?
2.Avoid unnecessary accelerating suddenly． 2.Turn the ignition switch to ON position．
3.Press the starting button while squeezing
the brake 1evers．
Control the bars while turning the throttle．
Re-start the engine after you have confirmed the above
items．

THE START ENGINE UN-ROTATE

Press the button ， if the start engine does not
rotate．check：
1．If the ignition switch is in the ON position?
2． Press the start button mean while squeezing the front
!CAUTION or the rear brake ,if it is still not started.
Don’t a11ow to drive with single hand or both hands free， 3． Turn the ignition switch to ON position and press the
don’t allow to 1oad goods or children on the horn button, if the horn has no noise to see if the
footrest． Obey the safe speed and remember safe driving． capacity of the battery is not enough

- 20 -

Downloaded from www.Manualslib.com manuals search engine

 PAY ATTENTION TO S ECURITY WHILE INS PECTING
THE ENGINE IS OFF WHILE DRIVING
NOTE
Please check the following items;
1.Place the motorcycle on the center stand on a wide
1.Is there fuel?
and plat place.
If there is no fuel in the fuel tank, go to the nearby
2.Avoid hurting from the heat of engine and exhaust
gas station to add fuel to the engine.
pipe.
After you have committed the above items, start the
3.If you inspect the drive performance, drive in a
engine again in the way of page 15.
safe place while paying attention to the surroundings.
2.If the engine can still not be started, go to service
station. INSPECTION ITEMS BEFORE DRIVING
The driver should do the inspection before driving every day.
1.The abnormal parts from the last day ,the function
INSPECT BEFORE DRIVING of the brakes and the play between the brake levers.
2. check the tyres pressure and cracks, damages,
To ensure you drive the motorcycle safely and
abnormal wearing, if there are metal, stones and glass in
comfortably. Please obey the traffic regulations and in-
the tyres.
spect periodically every 6 months and 12 months and check
every day before driving.
3.the depth of the threads；
4.the oil in the engine；
5.The fuel;
6.the lights and the turn signals
7.the pictures in the mirrors：
!CAUTION 8.dirts or damages of the mirrors and the brand．

1.If you feel the motorcycle is abnormal, consult the CHECK THE ABNORMAL PARTS FROM THE LAST DAY
service station.
Check the abnormal parts that you have found from the
2.Don’t forget to inspect it periodically while
last day while driving to see if they will affect driving
storage.
the motorcycle．
3.Careful inspections should be done after storage.
- 21 -

Downloaded from www.Manualslib.com manuals search engine

 CHECK THE FUNCTION OF THE BRAKES × 0 ×
Squeeze the brake levers to see if the play is between
the standardized limits．

10∽20mm 10∽20mm

more suitalbe less

!CAUTION
The abnormal tire pressure and tire crack ＆ damages
and abnormal wearing are the mail causes to make
unfunctional turning and explode the tires．

Replace the tire when the tread depth is less than 1mm
Replace the tire when crack or scratch occurs

CHECK IF THE FUEL IS ENOUGH TO DRIVE TO DESTINATION

Turn the ignition to switch to ON position, if the

indicator is before E，please add fuel to your motorcycle．
CHECK THE TIRES
the pressure of the tires
observe the part of the tires where touch the ground
to see if the pressure is normal . If it is abnormal，
check and adjust it by using the pressure gauge

- 22 -

Downloaded from www.Manualslib.com manuals search engine

 CHECK LUBRICANT OF THE ENGINE
Turn the ignition switch to ON position to see if the
oil indicator 1it or not ， if it is lit， please add
Lubricant oil to the engine.

!CAUTlON
Don’t make lubricant oil in the engine run off other
- wise the engine will be damaged while driving.

CHECK THE LAMP AND THE TURN SIGNALS

1. Start the engine and operate the lighting switch
to see if the front lamp and rear 1amp are lit or not．
2. operate the 1evers of the front and rear brakes to
see if the brake indicator is lit or not．
3. operate the switch of the turn signals to the left CHECK THE MIRRORS
or the right signals are normal or not． Check the mirrors by sitting on the seat to see if you
can clearly see the back and side part from the mirrors．

- 23 -

Downloaded from www.Manualslib.com manuals search engine

 ! CAUTION
1.Pay much attention to security while inspecting.
2.Place the motorcycle on the center stand on a wide
and plat place．
3.Avoid hurting from the heat of engine and exhaust
pipe．
4.Don’t start the engine in a close room because of
the noxious gas from starting the engine．
5.If you inspect the drive performance drive in a safe
place while paying attention to the surroundings.
6.If you have found it abnormal．Drive it after you
have solved the problems．bars up and down．

CHECK THE OPERATION PART

Check if the front fork is bent or damaged．Check if
there is abnormal noises while shaking the handle bars up
and down．
If the front fork is abnormal, consult KINROAD service
PERIODICAL INSPECTION
station.
Periodical inspections are done by the riders them
selves, they are divided into 6 monthly and l2 monthly CHECK THE BRAKES
inspections． The rear and front brake lever play
There are two sections：A section and B section in After adjusting the play, check that there is no
6-monthly inspections． dragging when turning rear wheel with the wheel off the
A section：I f you have basic knowledge of motorcycles， ground and that there is enough clearance between the rear
you can do the inspections by yourselves． brake lever and grip when the lever is tightly squeezed
B section：To do the inspections in this section， The rear and front brake lover play measured at the
you need special technical knowledge and special tools．You end of the levers should be 10-20mm.
can entrust the service station to do such inspections．

- 24 -

Downloaded from www.Manualslib.com manuals search engine

 10-20mm 10-20mm

please refer to page 31 to adjust me brake lever play．

FUNCTION OF THE BRAKES . Tire pressure: front :175KPa
Check the front and rear brakes。function separately Rear :225Kpa
by drive on the dry road with 1ow speed． If the tires are abnormal，please go to dealers service
station or replace them．
If the function of the brakes is not good, please refer CHECK THE AIR CLEANER ELEMENTS
to page 31 about brake shoe corrosion. Check if it prevents air going through by the dirty
CHECK THE TIRES air cleaner elements．

PRESSURE OF THE TIRES !CAUTION

Check pressure with pressure meter when they anr cool． 1.If the air cleaner elements are installed
completely，it will affect the engine by dirt going into．
2.No water should go into it when washing the
motorcycle.

- 25 -

Downloaded from www.Manualslib.com manuals search engine

 CHECK THE LEVEL OF OIL OF THE ENGINE
CHECK THE FLUID VOLUME OF THE BATTERY Take off the cover to check if the oil in the oil tank
This battery need not maintaining. is enough．If the oil is not enough，please add the special
Need not check or add battery fluid． 4 stroke oi1.
!CAUTION
1.Do not pull off the seal plug since it is closed CHECK LEAKAGE OF THE FUEL
type． Check the fuel tank，the fuel tank valve，the line and
2 Store the battery outside your motorcycle if you the carburetor to see if there is gasoline leakage．The
will not drive it for long time ． If store it in the oil 1ine is worn or not．If the fuel leaks and the oil line
motorcycle you should shut Off the negative terminal． is abnormal，go to the dealers service station to check．
CHECK THE TRANSMISSION LEAKAGE
Check the transmission to see if there is oil leakage

If the transmission leaks oil please go to KINROAD

service station．
CHECK THE LUBRICANT OF THE ENGINE CHECK THE FUNCTION OF THE LIGHTS ＆ THE TURN
Check the oil pump and the oil tank to see if there SIGNAL INDICATOR
is on leakage．If there is oil 1eakage p1ease ask KINROAD
dealer to check and maintain it 1.Check the lights with the head light, turn signals

- 26 -

Downloaded from www.Manualslib.com manuals search engine

 and the tail light． end of the levers should be 10-20mm
2.Check the lightness and direction of the lights by After adjusting the play, check that there is no
making the light towards the wall dragging when turning rear wheel with the wheel off the
3.Start the turning indicator to check if it flashes ground and that there is enough clearance between the rear
60—120 times in one minute． brake lever and grip when the lever is tightly squeezed.
4.Check covers of every light to see if there are some
damages and loose places．
CHECK THE LUBRICANT STATUS OF THE MOTRCYCLE
Check if the lubricant oil is enough of every part Of the
motorcycle．

SIMPLE MAINTANCE METHODS

After the above inspections, you should do some other
simple adjustments replacements．This manual will give
some common and useful maintenance methods．

!CAUTION
Pay attention to safety when you maintain your
motorcycle．
1.select a safe place which is flat ，Wide and no
dangers around.
2.Maintain it when it stops.
3 place the motorcycle on the center stand when
maintaining.
4.Use proper tools．
5.Pay attention to the heat of the engine and the
exhaust pipe.

FRONT& REAR BRAKE ADJUSTMENT

the rear and front brake lever play measured at the
- 27 -

Downloaded from www.Manualslib.com manuals search engine

 INSTALL AND ASSEMBLE THE FUSE
!CAUTION Take the terminal from the battery, and take off the fuse
Make the pin in the concave part of the adjuster from the terminal.
otherwise, the clearance between the rear brake 1ever and
grip will change when driving and it is very dangerous． MAIN POINTS
Don’t touch the central part of the terminal after
you take it down from the battery．

!CAUTION`
Replace the brake shoe if the marked continuous line
is out of the limits when you take the brake lever tightly. !CAUTION
1.Always be sure to replace the blown fuse with the
CORROSION OF THE BRAKE SHOE correct amperage fuse．
To know the corrosion status of the brake shoe． please 2.Using super amperage fuse will lead to heat or
inspect the places as the picture shows．Press the brake damage of the lines．
lever to the end．if the indicator shows that it is out 3.If the spare fuse installed blows in a short period
the using limits ， please go to the dealer’s service of time，please try to find other cause，replace fuse after
station to replace it． you have solve these causes.
4.Avoid water going into the fuse box when washing
your motorcycle．

CLEAN THE TERMINAL OF BATTERY

REPLACE THE FUSE 1.Wash the terminal with warm water when there are
Turn the ignition switch to OFF to check if the fuse white powder on it，if it is badly corrosive，use metal
is complete，replace the fuse if it is blown． brush．
2.Add some solid lubricant to the terminal when in—
The fuse is on the terminal of the battery，the standard stalling it．
current flow is 15 A.

- 28 -

Downloaded from www.Manualslib.com manuals search engine

 correctly，injures and damages will happen．
1.Fire is forbidden，short circuit should be prevented,
and smoke and other fire should be far form it．
2.Charge the battery in a ventilating place
It is easily explosive in a closed place．
3.No intensive strike such as falling down．
EMERGENCY METHODS
If your skin or cloth has touched the battery liquid,
wash with water immediately, If your eyes have it, wash
with water first, then go to the hospital.
WASH THE AIR CLEANER ELEMENT
!CAUTION
This motorcycle uses 12V—closed battery which need 1.Disassemble the air cleaner element：
not check the liquid and add water. 2.Wash the air cleaner element with non-flammable
cleaning solvent and dry it completely．
PAY MUCH ATTENTION TO THE FOLLOWS: 3.Immerse the air cleaner element in a pool of clean
1.It cannot use unclosed battery． motor oil and squeeze the oil off the air cleaner element
2.The battery has been charged and added battery to make it slightly wet with the oil．
liquid，you need not check the level of the liquid or add 4.Re-assemble the air cleaner element，
water
3.Please use the special closed charger when charging.
4.Charge the battery every 6 months when it is used
for a 1ong time．
5.If you use other charger except for the c1osed
battery，obey the following rules to prevent overcharging
standard：0.25A* 8hours
Fast charge is forbidden．

PAY ATTENTION TO USING THE BATTERY

The battery can have flammable gas，if it is not used
- 29 -

Downloaded from www.Manualslib.com manuals search engine

 !CAUTION
1.Gasoline and low ignition-point solvent is easily
flammable, so please not use them when washing the air
cleaner element.
2.Uncomplete assemblage will affect driving so make
sure to assemble the air cleaner clement fixed.
3.Aviod water entering the air cleaner element when
washing the motorcycle.
4.A torn air cleaner element must be replaced with a
new one.

PARTS NEED PERIODICALLY REPLACEMENT

With driving your motorcycles， sometimes you
can not judge some parts which can be used 1onger or
not without external changes． Under this case， you must
replace some important parts periodically.
To ensure your safe and comfortable driving, we hope
you can replace these parts periodically．For example：
1.brake line：every 2 years
2.fuel hoses：every 4 years
3.oil for transmission case：every 1000 km When you
replace parts，please buy them from motorcycle dealers.

- 30 -

Downloaded from www.Manualslib.com manuals search engine

 SPECIFICATIONS
50CC 50CC
Overall length 1670mm Cylinder bore × stroke 39 mm×41.4 mm
Overall width 640mm Compression ratio 9.2:1

Overall height 1060mm Output(max) 2.0kw/7500r/min

Wheelbase 1190mm Torque(max) 3.0N.m/4500r/min

Dead weight 78kg Idling speed 1500r±100r/min

Payload 150kg Displacement of cylinder 49 ml

Front wheel 3.50-10 Spark plug A7TC

Rear wheel 3.50-10 Spark plug gap 0.6-0.8mm

Speed(max) 45km/h Inlakevalve:0.05mm

Gap of air valve
Braking distance ≤7m(30km/h) Exhaust valve:0.08mm
Climb ability ≥18° Ground clearance 130mm
Capacity of gasoline tank 5.5L Ignition means CDI

Transmission ratio
Maximum transmission ratio 26.52
Minimum transmission ratio 8.84
Final reduction

- 31 -

Downloaded from www.Manualslib.com manuals search engine

 ELECTRICAL DIAGRAM

- 32 -

Downloaded from www.Manualslib.com manuals search engine