®

we care about the world

FILTRATION
SYSTEMS
Irrigation • Water Treatment

asbir.com.tr
we care about the world
a s b i r. co m . t r
 TABLE OF CONTENTS

FILTRATION 06

iClean® AUTOMATIC SCREEN FILTER 07

iClean® AUTOMATIC PLASTIC DISC FILTER 12

iClean® AUTOMATIC PLASTIC DISC FILTER SYSTEMS 16

MEDIA (GRAVEL) FILTER - 1000 SERIES 18

AUTOMATIC GRAVEL FILTER SYSTEMS 22

GRAVEL (MEDIA) FILTER - BYPASS 23

DOUBLE GRAVEL FILTER 24

HYDROCYCLONE (SAND SEPARATOR) - 2000 SERIES 26

SUCTION FILTER 30

METAL SCREEN - DISC FILTERS - 3000 SERIES 32

FERTILIZER TANK - 5000 SERIES 35

BACK - FLUSHING VALVES 37

OTHER PRODUCTS 40
 FILTRATION SYSTEMS
® FILTRATION

Obstruction of sprinklers and drippers is one of most significant problems encountered in irrigation systems. Most common reason of the
obstruction is about minerals, organic and inorganic materials found in the water resource. Process of filtering water in the irrigation
system is referred as filtration. Filtration is the best protection method against avoiding entrance/obstruction of dripper, sprinkler, hydrant
and other similar equipments used in the irrigation system by sediments. Because, process of finding the obstructed dripper, to clean or
replace the dripper is very costly and laborious. Therefore, filtration is most significant control unit of an irrigation system.

• Maximum and Minimum Pressure

• Water Source and Type of impurity
• Future needs and Modifications • Type Of Filter To Be Used
• Required Flow (Capacity)
• Required Water Quality 1. Sand Separators (Hydrocyclones) :
• Required Filtration (Pore size or micron)
• Pre-Filtration Requirement Hydrocyclones are designed in simple structure to be used in the
filtration of well water or other water sources containing sand, gravel
or particles heavier than the water.
• Filter Selection Table
2. Screen Filter :
Type of Impurity Type Of Filter To Be Used
Disc filters are designed to ensure deep filtration as a consequence
Hydrocyclone of one-on-one order of many disc sheets manufactured from nylon
Sands (Wells) iClean® Automatic Disc Filter reinforced polypropylene material on a filter body.
iClean® Automatic Screen Filter
Algae Hydrocyclone
Organic Matter Gravel (Sand-Media) Filter 3. Disc Filters :
(River water, iClean® Automatic Disc Filter
It is a filter which is constructed by assembling many tiny synthetic
Reservoirs) iClean® Automatic Screen Filter
discs manufactured from polypropylene material on filter body. The
Suspended Solids most advantage of the filter than screen filter is performing deep
Gravel (Sand-Media) Filter
Silt(Rivers, Lakes,
iClean® Automatic Disc Filter filtration, easy back-flushing and long term usage.
Channels)
Hydrocyclone
Well, Lake,
Gravel (Sand-Media) Filter 4. Media Tanks for Sand-Gravel Filters :
Creek Silts
iClean® Automatic Disc Filter
Wastewater Reuse Gravel (Sand-Media) Filter Filtration rates of gravel filters designed to be used in filtration
(Wastewater after iClean® Automatic Disc Filter of river, lake, pool water and water resources containing organic
secondary treatment) materials such as lichen and alga. Sand-Gravel Filters can be cleaned
up with automatically or manually. The gravels which is used as filter
Pre-Filtration Suction Filter
element must be replaced with new ones at the end of the season.

• Mesh and Disc Numbers Based On Particulate Matter Dimension Classification

Particle Screen and Disc Number Screen and Disc Number

Particle Class
Size (mm) (mesh) (micron)
Very Rough Sand 1.0 – 2.0 10 – 18 1500 – 850
Rough Sand 0.50 – 1.0 18 – 35 850 – 420
Intermediary Sand 0.25 – 0.50 35 – 60 420 – 250
Fine Sand 0.10 – 0.25 60 – 160 250 – 100
Very Fine Sand 0.05 – 0.10 160 – 270 100 – 50
Silt 0.002 – 0.05 270 – 400 50 – 30
Clay < 0.002 > 400 > 30

6 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC SCREEN FILTER ®

• Description
iClean® is the ideal solution for agricultural and municipal filtration due to its large filtration area, reliable operation mechanism and
simple structure. iClean® works on differential pressure and cleans itself automatically without any external intervention. iClean® has
electronically activated models besides hydraulically controlled models. Due to suction nozzles, cleaning is achieved with little water
consumption. Besides the standard 130 micron filter size, different screen sizes are available for different dirt levels.

• iClean® SERIES
• Electric Activated Automatic Screen Filter

iVE Series iHE Series

• Hydraulic Controlled Automatic Screen Filter

iVH Series iHH Series

asbir.com.tr 7
 FILTRATION SYSTEMS
® iClean® AUTOMATIC SCREEN FILTER

• Operation Principle
iClean® series can perform automatic cleaning without any external power supply or optionally with electrical activation from a distance.
The filter screen can achieve filtration capacities from 25 m³/h to 200 m³/h. Standard filter screen degree is 130 micron and inlet/outlet
diameters are available from 2”up to 8”.

drainage
outlet
inlet

• Filtration Method
Filtration starts as the dirty water enters the coarse screen from the inlet. In order to protect the fine filter, large particles are filtered on
the coarse filter. Water then passes through the fine filter, particals are captured by the fine filter, and clean water leaves from the outlet.
Particals gradually accumulating on the fine filter, increases the pressure difference. Once the pressure difference exceeds the preset
pressure differential value, filter automatically starts to clean itself.

• Cleaning Method
Once the pressure difference exceeds the preset pressure differential value, hydraulic control unit opens the drainage valve and the
cleaning cycle starts. Particals accumulated on the fine filter, are sucked by the nozzles and the turbine and discharged from the drainage
pipe. Thus cleaning operation is achieved. Filtration is not interrupted and iClean® continues filtration during the cleaning cycle.

• Features
•Most efficient filtration method
•Reliability: efficient filtration at various flow rates
•Low pressure loss
•Automatic self-cleaning system
•Uninterrupted filtration during self-cleaning
•Low maintenance cost

• Applications
•Agricultural applications
•Industrial applications
•Municipal applications
•Water management
•Cooling towers

8 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC SCREEN FILTER ®

• Material List (iHH-iHE Series)

Part No Part Name Material

1 Body ST37-2 Polyester Coating

2 Bonnet and Piston Mechanism GG25+SST

3 Screen Group PVC+PA6 Polyamide

4 Drain and Suction Nozzle Set SST Pipe+PA6 Polyamide

5 Coarse Screen PA6 Polyamide

6 Bonnet ST37-2 Polyester Coating

7 Bolts and Nuts SST

• Material List (iVH-iVE Series)

Part No Part Name Material

1 Body ST37-2 Polyester Coating

2 Bonnet and Piston Mechanism GG25+SST

3 Screen Group PVC+PA6 Polyamide

4 Drain and Suction Nozzle Set SST Pipe+PA6 Polyamide

5 Bolts and Nuts SST

asbir.com.tr 9
 FILTRATION SYSTEMS
® iClean® AUTOMATIC SCREEN FILTER

• Dimensions

D L L1 L2 L3
Model
inch mm mm mm mm

iVH-iVE-25 2" 630 - - -

iVH-iVE-35 3" 630 - - -

iVH-iVE-50 3" 760 - - -

iVH-iVE-70 4" 760 - - -

iVH-iVE-100 4" 875 - - -

iHH-iHE-100 4" - 900 1907 2410

iHH-iHE-120 5" - 900 1907 2410

iHH-iHE-160 6" - 900 1907 2410

iHH-iHE-200 8" - 900 1907 2410

• Available Models

iVH-25 iVH-35 iVH-50 iVH-70 iVH-100 iHH-100 iHH-120 iHH-160 iHH-200

Filter Model Code
iVE-25 iVE-35 iVE-50 iVE-70 iVE-100 iHE-100 iHE-120 iHE-160 iHE-200

Max. Flow Rate 25 m³/h 35 m³/h 50 m³/h 70 m³/h 100 m³/h 100 m³/h 120 m³/h 160 m³/h 200 m³/h

Inlet/Outlet Dimension 2" 3" 3" 4" 4" 4" 5" 6" 8"

130 130 130 130 130 130 130 130 130

Standard Filtration Degree
micron micron micron micron micron micron micron micron micron

Min. Operation Pressure 2,5 bar 2,5 bar 2,5 bar 2,5 bar 2,5 bar 2,5 bar 2,5 bar 2,5 bar 2,5 bar

Max. Operation Pressure 10 bar 10 bar 10 bar 10 bar 10 bar 10 bar 10 bar 10 bar 10 bar

Max. Operation Temperature 60°C 60°C 60°C 60°C 60°C 60°C 60°C 60°C 60°C

Minimum flow for flushing

15 m³/h 15 m³/h 20 m³/h 20 m³/h 22 m³/h 30 m³/h 30 m³/h 30 m³/h 30 m³/h
(at 2.5 bar - 35 psi)

Flushing Cycle Time 10-16 sn 10-16 sn 10-16 sn 10-16 sn 10-16 sn 22-30 sn 22-30 sn 22-30 sn 22-30 sn

Filtration Area 750 cm² 750 cm² 1500 cm² 1500 cm² 2250 cm² 6800 cm² 6800 cm² 6800 cm² 6800 cm²

* Consult to Asbir Team for getting optimum flow depending on water quality and filtration degrees.

10 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC SCREEN FILTER ®

• Head Loss Chart (iVH-iVE) • Head Loss Chart (iHH-iHE)

bar bar

• Sample Application

Part No Part Name

1 Hydrocyclone

2 Air Valve

3 Quick Pressure Relief Valve

4 VE/VH iClean® Automatic Screen Filter

5 Pressure Sustaining Valve

Part No Part Name

1 Hydrocyclone

2 Air Valve

3 Quick Pressure Relief Valve

4 iHH/iHE iClean® Automatic Screen Filter

5 Pressure Sustaining Valve

asbir.com.tr 11
 FILTRATION SYSTEMS
® iClean® AUTOMATIC PLASTIC DISC FILTER

• Description
iClean® Automatic Plastic Disc Filter is constructed by assembling many tiny synthetic disc manufactured
from polypropylene material on filter body with telescopic structure. When synthetic discs arranged one-
on-other are centralized around within telescopic filter body, center of discs forms a hollow disc. They are
designed to perform a deep filtration based on desired micron level found on both sides of synthetic discs
and inter-sectioning of channels designed in crosswise manner. Most outstanding advantage of iClean ®
Automatic Plastic Disc filter is that automatically self cleans the filter when it is obstructed.

• Operating Principle
iClean® Automatic Plastic Disc Filter operates in two different modes including filtration process and back flushing process.
In back flushing process of iClean® Automatic disc filter, internal mechanism of filter, where synthetic discs are assembled, is
automatically flushed. During cleaning process, no need for assembly and disassembly cycle of filter’s internal mechanism ensures
continuousoperation.

• Filtration Process
Many synthetic discs assembled on telescopic filter body create
a hollow cylinder. Those discs assembled on the filter body are
compressed using spring force and water pressure. Due to above
mentioned arrangement of discs, many crosswise water channels
intersecting each other are formed between two discs. Polluted water
supplied from inlet pipe of iClean® Automatic Disc Filter is transferred
on discs due to cyclone effect arising from centrifuge wing found on
filter body. The polluted water supplied as mentioned above passes
from crosswise water channels and it is filtered depending on filtration
degree. Particles with diameter larger than channel diameter of the
disc attach to exterior surface of discs. Filtered clean water progresses
from hollow section of discs and thus, clean water is supplied to the
system from clean water pipe of the filter. As pressure resistance of
discs involved in iClean® automatic plastic disc filters shall cause no
change on filter surface, efficiency to trap solid particles will be very
high.

• Back-Flushing Process
Throughout filtration process, synthetic discs will be obstructed at a
particular time due to filtration of polluted water containing particulate
matter. Back flushing process of iClean® automatic disc filters
connected parallel to the system is timedependently started using
pressure gradient (DP) sensor or a control de- Groovede. The filtered
clean water is supplied in reverse manner along telescopic filter body
from the clean water pipe of iClean® automatic disc filter. Pressure of
back flushing water elongates distance between discs by removing
spring force on the synthetic discs. Pressure clean water is sprayed
from nozzles on filter body to the crosswise channels of discs. Due
to spray of pressure clean water, particles previously attached to the
channels of synthetic discs are cleaned and discharged. Back flushing
process is completed within short time such as 15-20 seconds. Thus,
coupious amount of water is not used for flushing iClean® automatic
disc filter, as the case for other filters. At the end of the back flushing
process, filter is shifted to filtration position.

12 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC PLASTIC DISC FILTER ®

Filtration
Filtration

Back-Flushing

• Description
Back flushing control valves adjusting filtration and back
flushing positions of iClean® automatic disc filters connected
parallel to the manifold collector system are programmed by
differential pressure sensor (DP) for pressure and by control
device for timedependent parameters.It is possible to control
the system manually with 3-way butterfly valves and ball
valves instead of back-flushing valves.

• Disc Filter Degree Measures

Effective Filtering
Model No Micron Disc Color
Surface (%)
AF80 200 %39 Blue

AF120 130 %39 Red

AF150 100 %40 Yellow

• Applications
• Filtration of well water
• Filtration of river, lake and reserve water
• Filtration of applications such as process water and cooling water
• Upwards the ultra-filtration systems
• Agricultural drip and micro-irrigation systems
• For recreational irrigation system practices

• Specifications
• Back flushing process is completed in automated manner.
• Water supply is not interrupted during back flushing process.
• As it can be cleaned within short time, very low amount of water is used in back flushing process.
• Due to discs with varying dimensions, desired filtration degree is ensured.
• Maintenance during operation is very easy.
• As it is used in modular filter systems, filtration at desired rates can be performed.
• Due to body and framework reinforced against corrosion, it has long operation life.

asbir.com.tr 13
 FILTRATION SYSTEMS
® iClean® AUTOMATIC PLASTIC DISC FILTER

• Dimension and Weight

• Available Models and Recommended Flow Rates

Recommended
Model W ØD H L Weight Filtration Area
Flow Rate
Auto 246 mm 214 mm 776 mm 320 mm 9 kg 1520 cm² 25-35 m³/h

• Technical Specifications
Max. Operating Min. Back-Flushing Min. Back-Flushing
Temperature Connection
Pressure Pressure Flow Rate
8 ( bar ) 1 ( bar ) 0 °C – 60 °C 3” (80 mm)
9 – 11 m³/h
120 ( psi ) 14 ( psi ) (32 °F – 132 °F ) Grooved End

3” - 80 mm
3” - 80 mm GROOVED END
GROOVED END

3” - 80 mm
GROOVED END

14 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC PLASTIC DISC FILTER ®

• Material List
Part No Part Name Material

1 Body PA6 GFR30

2 Lid PA6 GFR30

3 Hydrocyclone Wing Nylon 6

4 Filter Frame PA6 GFR30

5 Disc Nylon Reinforced PP

6 Collar AISI 304

• Head Loss Chart

bar

• Available Model and Recommended Flow Rates

Modules Recommended Flow Min. Back-Flushing Max. Operating Min. Back-Flushing
Filtering Area Connection
pcs (100,150,200 micron) Flow Rate Pressure Pressure
2 module 60 m³/h 18 m³/h 8 bar 1 bar 3040 cm² Grooved End
3 module 90 m³/h 27 m³/h 8 bar 1 bar 4560 cm² Grooved End
4 module 120 m³/h 36 m³/h 8 bar 1 bar 6080 cm² Grooved End
5 module 150 m³/h 45 m³/h 8 bar 1 bar 7600 cm² Grooved End
6 module 180 m³/h 54 m³/h 8 bar 1 bar 9120 cm² Grooved End

*Please consult us for higher flow rate systems.

asbir.com.tr 15
 FILTRATION SYSTEMS
® iClean® AUTOMATIC PLASTIC DISC
FILTER SYSTEMS

• iClean® Automatic Disc Filter System

Collector Size Capacity

Code Disc Filter
Quantity
inch m3/h

ADF-02 4" 2 50
ADF-03 4" 3 75
ADF-04 5" 4 100
ADF-05 6" 5 125
ADF-06 6" 6 150
ADF-07 8" 7 175
ADF-08 8" 8 200

•CONTROLLER, CONNECTION EQUIPMENTS, AIR VALVES AND PRESSURE GAUGES ARE INCLUDED IN
THE SYSTEM.
•FERTILIZER KIT AND FERTILIZE TANK ARE NOT INCLUDED IN THE SYSTEM.
•PACKAGE: WOODEN CRATE.

16 asbir.com.tr
FILTRATION SYSTEMS
iClean® AUTOMATIC PLASTIC DISC ®
FILTER SYSTEMS

• iClean® Hydrocyclone+Fertilization+Automatic Disc Filter System

Fertilizer
Collector
Tank Capacity
Size Disc Filter Hydrocyclone
Code Quantity
Quantity Quantity
inch lt m³/h
A-4H-100G-P2 4" 2 1x4" 100 50
A-4H-100G-P3 4" 3 1x4" 100 75
A-5H-100G-P4 5" 4 1x5" 100 100
A-6H-200G-P5 6" 5 1x6" 200 125
A-6H-200G-P6 6" 6 1x6" 200 150
A-2x5H-300G-P7 8" 7 2x5" 200 175
A-2x5H-300G-P8 8" 8 2x5" 300 200

•CONTROL UNIT, CONNECTION EQUIPMENTS, AIR VALVE, PRESSURE GAUGE ARE INCLUDED IN THE SYSTEM.
•FERTILIZATION KIT AND FERTILIZER TANK ARE INCLUDED IN THE SYSTEM.
•STANDARD FILTRATION DEGREE: 130 MICRON (120 MESH)
•STANDARD CONNECTION IS FLANGED. GROOVED END AND THREADED CONNECTIONS ARE ON REQUEST.
•PACKAGE: WOODEN CRATE.

asbir.com.tr 17
 FILTRATION SYSTEMS
®
MEDIA (GRAVEL) FILTER 1000 SERIES

• Description
Filtration rates of gravel filters designed to be used in filtration of river, lake, pool water and water resources containing organic
materials such as lichen and alga is over 15 m/h implicating that they are rapid filters. The outstanding advantage of the gravel
filters against other types of filters is about maximum filtration efficiency due to deep filtration. Asbir 1000 series Gravel filters
are designed to provide ease of use, maximum filtration efficiency and less maintenance due to simple structure and thus, they are
offered to the users.

Asbir 1000 series Gravel filters are manufactured to contain at least two containers. Upper container located within filter vessel
is the container of media ensuring the filtration process. In the media container, various materials including but not limited to
sand-gravel, quartz sand, Anthracyte coal, grinded basalt, silica sand are placed in a particular order based on the filtration degree.
Lower container is the clean water tank obtained from filtering process. A rubber diffuser plate separating said two containers is
present within the filter. Corks assembled on the plate ensure uniform pressure during back flushing procedure of the media filter
and thus, they are designed to provide an efficient back flushing process.

Asbir 1000 series Gravel Filters are projected to operate single or modular and manual or fully automatic back flushing procedure
based on the water flow rate to be filtered within scope of the field of use. In order to increase filtration efficiency of gravel filters,
it is recommended that modular filter system is selected from a model operating automatic back flushing
procedure.

• Operating Principle
Asbir 1000 series Gravel Filters operates in two different modes including filtration process and back flushing process.
Asbir media filters are back flushing control gates assembled on the filters to be operated in filtration or back flushing procedures.

• Filtration Process
Polluted water entering from inlet manifold of the filter reaches media filter
via back flushing control gate. At this position, inlet port of the back flushing
control gate is towards the filter’s direction and discharge port is closed.
Polluted water reaching the media filter slowly progresses through sand layer
placed in the filter depending on the desired filtration degree and thus, it is
deeply filtered. Particles found in polluted water are trapped by sand later.
Water passing through sand layer and filter corks will supplied to the system
via outlet (clean water) manifold.

18 asbir.com.tr
FILTRATION SYSTEMS
®
MEDIA (GRAVEL) FILTER 1000 SERIES

• Back-Flushing Process
Throughout the filtration process, particles suspended in the sand layer shall later cause obstruction
in the filter following a particular operation period. Therefore, pressure loss in the system will increase
and media filter is required to be cleaned. Cleaning process of media filters is referred as back flushing.
During back flushing process, the issue required to be considered is to wash the filter using clean
water. Element ensuring back flushing process is the back flushing control gate assembled on the
filter. In this case, inlet port of the back flushing control gate is closed and discharge port is at open
position. Pressure clean water supplied from outlet (clean water) manifold progresses to sand layers
from filter corks. Particles suspended among sand layers are pushed forward under effect of pressure
clean water and they are released to the atmosphere from discharge port of the back flushing control
gate. Thus, filter is efficiently cleaned. Duration of back flushing process is adjusted according to
obstruction degree of the filter. It is highly recommended that a short-term back flushing process in
regular intervals is performed rather than long-term back flushing process.

• Filtering Degrees of Media Filters

Sand Size Filtration Degree

Media Sand Number Material
mm inch micron mesh

16 Grinded Silica 0,66 0,026 70 - 100 140 - 200

20 Grinded Silica 0,46 0,018 65 - 80 200- 230

12 Quartz Sand 1,2 - 2,4 0,047 - 0,094 80 - 110 130 - 140

- Quartz Sand* 0,8 - 1,2 0,047 - 0,031 80 - 120 130 - 200

- Quartz Sand* 1,2 - 1,5 0,047 - 0,059 100 - 150 100 - 150

* Quartz sand is standard on agricultural irrigation systems.

• Sand Distribution Diagram of Gravel Filters

Recommended Sand Volume

Model
kg Ibs

1020 100 220,5

1520 100 220,5

1024 150 330,7

1030 225 496,0

1036 250 551,2

1536 250 551,2

1048 500 1102,3

asbir.com.tr 19
 FILTRATION SYSTEMS
® MEDIA (GRAVEL) FILTER 1000 SERIES

• Dimension

• Available Models and Recommended Flow Rates

Recommended
ØD H L
Flow Rate
Model ØA
mm inch mm inch mm inch m³/h l/s

1020 2" 500 20 1200 47,2 360 14,2 10 - 15 2,8 - 4,2

1520 2½" 500 20 1200 47,2 360 14,2 15 - 20 4,2 - 5,6

1024 3" 600 24 1170 46,1 360 14,2 20 - 30 5,6 - 8,3

1030 3" 750 30 1170 46,1 360 14,2 30 - 42 8,3 - 11,6

1036 3" 900 36 1170 46,1 360 14,2 42 - 60 11,6 - 16,7

1536 4" 900 36 1170 46,1 360 14,2 60 - 75 16,7 - 20,8

1048 4" 1200 48 1170 46,1 360 14,2 80 - 100 22,2 - 27,8

• Head Loss Chart

bar

20 asbir.com.tr
FILTRATION SYSTEMS
MEDIA (GRAVEL) FILTER 1000 SERIES
®

• Specifications • Fields of Use

•It provides ease of use and of maintenance due to simple structure. •Filtration of reserve waters such as river, lake and pool water
•Pre-painting phosphorization is performed for maximum resistance •Filtration of waters containing organic material
against corrosion. •Agricultural drip and micro-irrigation systems
•It has long economic life based on Epoxy – Polyester coating. •Filtration of industrial cooling water
•It designed for homogenous distribution of raw water and •Preliminary filtration of reverse osmosis systems
highly efficiency filtration.
•It performs efficient back flushing process when minimum pressure
loss occurs.
•Single or modular systems can be used for various application
fields with different diameters.
•Options of manual or automatic back flushing are available.

• Material List

Part No Part Name Material

1 Body ST37-2 Polyester Coating

2 Mushroom Filter Nylon 6

3 Bonnet Gasket-Monolithic Natural Rubber / EPDM

4 Bonnet GGG40 - Ductile Iron

5 Bolts and Nuts SST

• Technical Specifications
Recommended Max. Min.
Test
Operating Operating Back-Flushing Temperature Connection Coating
Pressure
Pressure Range Pressure Pressure
Flanged ISO
1. Phase:Phosphorization
0 °C – 80 °C 7005-2, ANSI
1 - 8 (bar) 8 (bar) 2 (bar) 12 (bar) 2. Phase:Electrostatic
(32 °F – 176 °F ) Threaded
14 - 120 (psi) 120 (psi) 30 (psi) 175 (psi) Powding
DIN 2401 /2 BSPT-NPT
Polyester - Epoxy)
Grooved End

• Sample Order Form

Model Inlet Diameter Tank Diameter Connection Control Feature Additional Features

1020 2" 20"

1520 2½” 20"

1024 3" 24"

Manual (M)
Grooved End (GRO) Pressure Sustaining Valve (PS)
Power Controlled (EL)
1030 3" 30" Threaded (TH) Flow Rate Control Valve (FR)
Battery Controlled
Flanged (F) Quick Pressure Relief Valve (QR)
(BT)
1036 3" 36"

1536 4" 36"

1048 4" 48"

1030 3 30 GRO EL PS

asbir.com.tr 21
 FILTRATION SYSTEMS
® AUTOMATIC GRAVEL FILTER SYSTEM

• Automatic Gravel Filter System

Code Capacity Tank Quantity Tank Size Collector Size

A10-G2-0220 24 m³/h 2 20"-2" 3"
A10-G3-0220 36 m³/h 3 20"-2" 4"
A10-G4-0220 48 m³/h 4 20"-2" 4"
A10-G2-0324 40 m³/h 2 24"-3" 4"
A10-G3-0324 60 m³/h 3 24"-3" 4"
A10-G4-0324 80 m³/h 4 24"-3" 5"
A10-G2-0330 60 m³/h 2 30"-3" 4"
A10-G3-0330 90 m³/h 3 30"-3" 5"
A10-G4-0330 120 m³/h 4 30"-3" 6"
A10-G6-0330 180 m³/h 6 30"-3" 8"
A10-G8-0330 240 m³/h 8 30"-3" 10"
A10-G2-0336 84 m³/h 2 36"-3" 5"
A10-G3-0336 126 m³/h 3 36"-3" 6"
A10-G4-0336 168 m³/h 4 36"-3" 8"
A10-G6-0336 252 m³/h 6 36"-3" 10"
A10-G8-0336 336 m³/h 8 36"-3" 12"
A10-G2-0436 120 m³/h 2 36"-4" 5"
A10-G3-0436 180 m³/h 3 36"-4" 6"
A10-G4-0436 240 m³/h 4 36"-4" 8"
A10-G6-0436 360 m³/h 6 36"-4" 10"
A10-G8-0436 480 m³/h 8 36"-4" 12"
A10-G2-0448 144 m³/h 2 48"-4" 5"
A10-G3-0448 216 m³/h 3 48"-4" 6"
A10-G4-0448 288 m³/h 4 48"-4" 8"
A10-G6-0448 432 m³/h 6 48"-4" 10"
A10-G8-0448 576 m³/h 8 48"-4" 12"

•CONTROL UNIT, BACK-FLUSHING VALVES, CONNECTION EQUIPMENTS, QUARTZ SAND, AIR VALVE, PRESSURE GAUGE ARE INCLUDED IN THE SYSTEM.
•BONNETS ARE GGG40 DUCTILE IRON AND GASKETS ARE MONOLITHIC NATURAL RUBBER.

22 asbir.com.tr
FILTRATION SYSTEMS
GRAVEL (MEDIA) FILTER-BYPASS ®

• Description
Gravel Filters can be also used as single unit by-pass modules except manual or automatic systems.

• Operating Principle Filtration Mode: 1,3: Open - 2,4: Closed

There are two types of flow; filtration and backflushing function. İncoming dirty
water from by-pass line is spread to inside of the gravel filter homogeneously.
The filtration is completed when the filtered water passed from mushrooms.
Accumulated dirt materials in filter will cause pressure loss. İt will cause reduce
the passing filtered flow. In this case, the filter must switch to the backflushing Drainage
mode in order to clean the filter. In the backflushing mode, incoming dirty water
from second chamber pass to mushroom plate. It act to the accumulated dirt
materials and provides to discharge from drain line. At this time, the butterfly
valve which is on the drain port of the by-pass line is open, other butterfly valve Filtered Water
is close. Collector

• Available Model Dimensions Back-Flushing Mode: 2,4: Open - 1,3: Closed

L1 L2
ØD

Recommended Flow
ØD H L1 L2
Inlet/Outlet Rate
Model
Sizes
mm inch mm inch mm inch mm inch m³/h l/s

1020-BP-500 2" 500 20 1204 47,4 852 33,5 884 34,8 10 - 15 2,8 - 4,2
1520-BP-500 2½" 500 20 1204 47,4 852 33,5 884 34,8 15 - 20 4,2 - 5,6
1024-BP-600 3" 600 24 1212 47,7 929 36,6 1022 40,2 20 - 30 5,6 - 8,3
1030-BP-750 3" 750 30 1239 48,8 1054 41,5 1215 47,8 30 - 42 8,3 - 11,6

asbir.com.tr 23
 FILTRATION SYSTEMS
® DOUBLE GRAVEL FILTER

• Description
Asbiŗ Double Gravel Filters are designed to use for the filtration of the water sources such as lake, dams, canals, creeks, water pools, etc.
which has algae and organic matters. It provides easy usage and maintenance thanks to its unique design.

• Operation Principle (Automatic)

Filter tank has two chambers. First chamber is distributer that dirty water entering in it. The section contains quartz sand and mushroom
diffusers is named media. The media chamber consists of two regions.There are two seperate cleaning chamers. The second chamber, clean
water chamber is under the media. The mushroom plate separates 2 chambers from each other. There are two types of flow; filtration
and backflushing function. İncoming dirty water from opening to gravel filter ports of backflushing valve is spread to inside of gravel filter
homogeneously from distributer.The filtration is completed when the filtered water passed from mushrooms. Materials that accumulated
in filter will cause pressure loss. İt will cause reduce the passing filtered flow.In this case, filter is necessary to switch to the backflushing
mode in order to clean the filter. İn the backflushing mode, incoming filtered water from second chamber pass to mushroom diffuser plate.
It act to accumulated dirt materials and provides to discharge from drain line of 3 way valve.At this time, connected ball valve section of 3
way valve is open, other port is close. All directions do manually. All of the media chamber don’t swich to backflushing mode at the same
time. While one side of the gravel is doing backflushing, the other side continue to filtration.

• Filtration Mode • Back-Flushing Mode

24 asbir.com.tr
FILTRATION SYSTEMS
DOUBLE GRAVEL FILTER ®

• Operation Principle (Manual)

Unlike automatic double gravel filtration, butterfly and ball valves are used instead of control panel and back-flushing valves. For this
reason, the filter can be manually switched to the filtering or back-flushing mode when required.

• Available Model Dimensions

Recommended Flow
H L1 L2
Inlet/Outlet Tank Rate
Model
Sizes Size
mm inch mm inch mm inch m³/h l/s

ADG-500 2" 20" 1034 40,7 639 25,2 1098 43,2 11-21 3,1-5,8
Automatic

ADG-550 3" 22" 1074 42,3 674 26,5 1081 42,6 27-54 7,5-15

ADG-750 4" 30" 1367 53,8 921 36,3 1685 66,3 42-85 11,7-23,6

ADG-900 5" 36" 1542 60,7 1045 41,1 1771 69,7 66-132 18,3-36,7

MDG-500 2" 20" 1061 41,8 639 25,2 1098 43,2 11-21 3,1-5,8

MDG-550 3" 22" 1102 43,4 671 26,4 1015 40,0 27-54 7,5-15
Manual

MDG-750 4" 30" 1297 51,1 921 36,3 1685 66,3 42-85 11,7-23,6

MDG-900 5" 36" 1476 58,1 1045 41,1 1771 69,7 66-132 18,3-36,7

L1 L2

asbir.com.tr 25
 FILTRATION SYSTEMS
® HYDROCYCLONE (SAND SEPARATOR) 2000 SERIES

• Description
Asbir 2000 series hydrocyclones are designed in simple structure to be used in the filtration of well water or other water sources
containing sand, gravel or particles heavier than the water. Due to simple structure, it is more economic and easy to use relative to
other sand separators. Asbir hydrocyclones causes minimum pressure loss in filtration systems and therefore, they operate at maximum
efficiency. Asbir 2000 series hydrocyclones, used as primary filtering element in filtration systems, are provided in single or modular
forms which ensure manual or fully automatic cleaning process.

• Operating Principle

Asbir 2000 series hydrocyclones is a separator removing particles heavier than the water
before they enter into the system. It is consisted of two main parts including the body and
collection container. Water containing particles heavier than the water enters into cylindrical
wall found on the body of the hydrocyclone in tangential manner. Water reaches a particular
speed in the cylindrical wall and thus, it creates centrifugal force. Due to this centrifugal
power, solid particles heavier than water fall down from narrowing conic part of the
hydrocyclone and trapped in the collection container. While solid particles heavier than water
fall down to collection container due to centrifugal force, clean water free from particles is
supplied to the system via outlet pipe. Water reaches desired speed on cylindrical wall due
to perfect cylindrical wall and conical body design of the Asbir 2000 series hydrocyclone and
thus, water increases efficiency of the filtration as it creates a cycloid orbit.

26 asbir.com.tr
FILTRATION SYSTEMS
HYDROCYCLONE (SAND SEPARATOR) 2000 SERIES ®

In order to get a regular filtration in Asbir 2000 series hydrocyclones, collection container should be
regularly monitored and cleaned depending on the water quality. Based on the application type,
hydrocyclones are provided in to forms, including manual and automatic, to the users. It is recommended
that users prefer automatic model ensuring regular monitoring and cleaning of collection container.

• Applications
•Filtration of reserve water such as deep well
•Filtration of water containing sand, gravel or particles heavier than water
•Preliminary filtration of gravel, Disc and mesh filters
•Agricultural drip and micro-irrigation systems
•Separation of solid particles larger than mesh diameter of 200.

• Specifications
•It provides ease of use and of maintenance due to simple structure.
•Pre-painting phosphorization is performed for maximum resistance against corrosion.
•It has long economic life based on Epoxy – Polyester coating.
•It operates completely based on cyclone principle.
•It performs filtration (separation) process with minimum pressure loss.
•Single or modular systems can be used for various application fields with different diameters.
•Two different models are available including manual and automatic.
•Automatic models can perform self-cleaning process without any disruption in water supply.

• Technical Specifications
Recommended
Max. Operating Test
Operating Temperature Connection Coating
Pressure Pressure
Pressure Range
- 10 °C – 80 °C Flanged ISO 7005-2, ANSI 1. Phase: Phosphorization
0.3 – 8 ( bar ) 8 ( bar ) 12 ( bar )
(14 °F – 176 °F ) Threaded BSPT-NPT 2. Phase: Electrostatic Powding
4 – 120 ( psi ) 120 ( psi ) 175 ( psi )
DIN 2401 /2 Grooved End Polyester - Epoxy)

asbir.com.tr 27
 FILTRATION SYSTEMS
® HYDROCYCLONE (SAND SEPARATOR) 2000 SERIES

• Dimension
ØD

ØA
ØA

H H1

• Available Models and Recommended Flow Rates

ØA Connection Types ØD H H1 Recommended Flow Rate

Model
mm inch Grooved End Flanged Threaded mm inch mm inch mm inch m³/h l/s

2050 50 2" 219 8,6 1045 41,1 955 37,6 10,5 17 2,9 4,7

2065 65 2½" 280 11,0 1215 47,8 1090 42,9 16 26,5 4,4 7,4

2080 80 3" 280 11,0 1215 47,8 1090 42,9 25 42 6,9 11,7

2100 100 4" 350 13,8 1425 56,1 1290 50,8 44 73,5 12,2 20,4

2125 125 5" 450 17,7 1675 65,9 1505 59,3 69,5 116 19,3 32,2

2150 150 6" 450 17,7 1675 65,9 1495 58,9 101 169 28,1 46,9

2200 200 8" 600 23,6 2200 86,6 1980 78,0 176 293 48,9 81,4

• Head Loss Chart

bar ½

28 asbir.com.tr
FILTRATION SYSTEMS
HYDROCYCLONE (SAND SEPARATOR) 2000 SERIES ®

• Material List

Part No Part Name Material/Equipment

1 Cylindrical Wall St37-2

2 Conical Body St37-2

3 Inlet Pipe St37-2

4 Outlet Pipe St37-2

5 Bolts and Nuts Natural Rubber / EPDM

6 Storage Chamber St37-2

7 Drainage Ball Valve/Control Valve

8 Bolt/Nut Stainless Steel

9 Bonnet GGG40/50 Ductile Iron

10 Gasket for Bonnet Natural Rubber / EPDM

• Sample Order Form

Model Inlet Diameter Connection Control Feature

2050 2"

2065 2½”

2080 3" Grooved End (GRO) Manual (M)

Threaded (TH) Power Controlled (EL)
2100 4" Flanged (F) Batter Controlled (BT)
2125 5"

2150 6"

2150 6 GRO EL

asbir.com.tr 29
 FILTRATION SYSTEMS
® SUCTION FILTER

• Description
Suction filter is designed to protect the pumps from debris and
foreign matters. It is generally used in water sources containing
algea, debris, and other heavy wastes. It is connected to pump
suction and submerged into water (river, lake, reservoir, etc.)

• Operation Principle
Water sucked by the pump passes through the strainer and debris is kept outside by the stainless steel screen. Rotating nozzles
are fed with water taken from the pump outlet. Water jets sprayed from the nozzles blow away the debris collected on the outer
surface of the screen and thus the filter is cleaned.

Thus the pump is protected against clogging and failures. Pump efficiency increases and maintenance costs decrease.

•Minimum working pressure: 1.5 bar (22 psi)

•Suggested working pressure: 3-4 bar
•Electrostatic coated body
•Rotating Nozzles
•Flange type Connection
•Electrostatic applied and oven-cured zinc-phosphate coating for anti-corrosion protection
•Available models: 4", 6", 8", 10", 12"

• Specifications
•Protection of pumps
•Low head loss Strainer Pump

•Automatic self-cleaning system

•Uninterrupted filtration during automatic self-cleaning
•Low maintenance costs
Water Source

• Applications
•Agricultural applications
•The water source which has Alga, Trash, Sand and the other heavy wastes
(Creek, lake, reservoir and etc.)

30 asbir.com.tr
FILTRATION SYSTEMS
SUCTION FILTER ®

• Material List
Part No Part Name Material

1 Body/Screen St37-2

2 Upper Bonnet St37-2

3 Turbine Mechanism PVC

4 Check Valve GG25+AISI304

5 Connection Bonnet St37-2

6 Gasket for Flange Natural Rubber

7 Bolts and Nuts Stainless Steel

• Technical Specifications

Model No SF-4 SF-6 SF-8 SF-10 SF-12

Maximum Flow Rate 80 m³/h 180 m³/h 315 m³/h 495 m³/h 710 m³/h

Connection Size 4" 6" 8" 10" 12"

5000* 5000* 5000* 5000* 5000*

Standard Filtration Degree
micron micron micron micron micron

Min. Operation Pressure 1,5 bar 1,5 bar 1,5 bar 1,5 bar 1,5 bar

Max. Operation Pressure 10 bar 10 bar 10 bar 10 bar 10 bar

Max. Operation Temperature 60°C 60°C 60°C 60°C 60°C

* Please consult to Asbir Team for different filtration degrees.

• Dimensions

ØD H
Model ØA ØB
mm inch mm inch

SF-4 4" 1 ¼" 380 15,0 814 32,0

SF-6 6" 1 ¼" 450 17,7 934 36,8
SF-8 8" 1 ¼" 550 21,7 1111 43,7
SF-10 10" 2" 600 23,6 1236 48,7
SF-12 12" 2" 640 25,2 1321 52,0

• Sample Order Form

Model Connection Size Connection Type

SF-4 4" Flanged (F)

SF-6 6" Flanged (F)

asbir.com.tr 31
 FILTRATION SYSTEMS
® METAL SCREEN DISC FILTER 3000 SERIES

• Description
Asbir D-3000 series disc filters are designed to ensure deep filtration as a consequence of one-on-one order of many disc sheets
manufactured from nylon reinforced polypropylene material on a filter body.

Having a simpler design Relative to different filter groups, Asbir 3000 series screen filters are really successful in filtration of water well
and water resources containing sand. Asbir 3000 series screen filters are manufactured in two body form including angle and horizontal
type for meeting needs of different application.

• Operating Principle
Polluted water containing particles heavier than water such as sand and gravel enters into the filter from inlet pipe of the Asbir 3000
series screen and disc filters. The water is filtered from the mesh found in screen-disc filters providing desired filter grade at micron level.
Particles with larger diameter than that of diameter of screen-disc are trapped by the mesh. Clean water filtered is supplied to the system
via outlet pipe of the filter. Heavy particles failing to pass from pores of the screen-disc are released to the atmosphere via discharge gate
found beneath the body of the filter.

• Applications • Specifications
•Filtration of well water •It provides ease of use and of maintenance due to simple structure.
•Filtration of water containing sand, gravel or particles •Pre-painting phosphorization is performed for maximum resistance
heavier than water against corrosion.
•Filtration of river, lake and reserve water •It has long economic life based on Epoxy – Polyester coating.
•Preliminary filtration of ultra-filtration systems •It performs filtration process with minimum pressure loss occurs.
•Downwards the hydrocyclon and gravel filter systems •It can be used in wide range of applications due to varying filtration
•Agricultural drip and micro-irrigation systems rates and degrees.
•For recreational irrigation system practices •It has long economic life due to nylon polypropylene discs.
•Downwards the fertilization system •It may be used in single or modular form in the application fields.
•It ensures easy assembly to systems with angle and horizontal type
models.

32 asbir.com.tr
FILTRATION SYSTEMS
METAL SCREEN DISC FILTER 3000 SERIES ®

• Disc-Screen Filter Degree Measures

Mesh No Micron Effective Filtering Surface Color

**80 200 %39 Blue

*120 130 %39 Red

*150 100 %40 Yellow

* 130 micron (120 mesh) screen is standard.

**100 micron (150 mesh) and 200 micron (80 mesh) on request.

• Material List (Screen Filter)

Part No Part Name Material

1 Body St37-2

2 O – Ring NBR

3 Screen PA6 Polyamid

4 Lid Seal NBR/EPDM

5 Lid GGG40/50

6 Arm GGG40/50

7 Discharge Valve GG 25/GGG 40

• Material List (Disc Filter)

Part No Part Name Material

1 Body St37-2

2 Disc Frame PA6 GFR30

3 O – Ring NBR/EPDM

4 Disc Nylon Reinforced PP

5 Lid O-Ring NBR/EPDM

6 Lid GGG40/50

7 Arm GGG40/50

asbir.com.tr 33
 FILTRATION SYSTEMS
® METAL SCREEN DISC FILTER 3000 SERIES

• Dimensions

Y Type disc-screen filter (Y-D 3000 series) Angle Type dic-screen filter (L-D 3000 series)

• Available Models and Recommended Flow Rates

Recommended Flow
ØA ØD H L
Rate
Model
mm inch mm inch mm inch mm inch m³/h U.S gpm

Y(D)3050 50 2 168 6" 350 13,8 485 19,1 18 25 5,0 6,9

Y(D)3065 65 2½" 168 6" 350 13,8 490 19,3 28 42 7,8 11,7
Y(D)3080 80 3" 219 8" 450 17,7 600 23,6 38 50 10,6 13,9
Y(D)3100 100 4" 219 8" 450 17,7 600 23,6 40 75 11,1 20,8
Y(D)3125 125 5" 219 8" 600 23,6 730 28,7 90 125 25,0 34,7
L(D)3050 50 2 168 6" 600 23,6 140 5,5 18 25 5,0 6,9
L(D)3065 65 2½" 168 6" 600 23,6 140 5,5 28 42 7,8 11,7
L(D)3080 80 3" 219 8" 875 34,4 160 6,3 38 50 10,6 13,9
L(D)3100 100 4" 219 8" 875 34,4 160 6,3 40 75 11,1 20,8

• Head Loss Chart

bar ½ bar ½

Y Type disc-screen filter (Y-D 3000 series) Angle Type disc-screen filter (L-D 3000 series)

• Sample Order Form

Model Inlet Diameter Connection Type Control Feature Filtration Degree

YD3065-LD3065 2"
Grooved End (GRO) Manual (M) 100 Micron
YD3080 - LD3080 3" Threaded (TH) Power Controlled (EL) 130 Micron
Flanged (F) Batter Controlled (BT) 200 Micron
YD3125 5"

YD3050 4 GRO M 130

34 asbir.com.tr
FILTRATION SYSTEMS
FERTILIZER TANK 5000 SERIES ®

• Description
Asbir 5000 series fertilizer tanks are developed for chemical fertilizer or pesticide applications directly to root region of the plant
using irrigation water of drip or sprinkler irrigation systems. It ensures very practical and convenient fertilizing and pesticide
administration in irrigation systems due to simple structure and ease of use. Different models with varying capacities are available
including horizontal and vertical types depending on different needs of present irrigation system. Operating based on pressure
difference principle in the irrigation systems, Asbir 5000 series fertilizer tanks will operate long years without requiring maintenance
due to resistant construction.

• Operating Principle
Asbir 5000 series fertilizing tank is connected parallel to main pipe of irrigation system
using elastic hoses via by-pass method. Irrigation water enters into the tank containing
soluble chemical from the inlet hose of fertilizer tank connected to the line. Due to
pressure gradient created using a valve or pressure reducer assembled on the irrigation
line, chemical fertilizer is solved and it is blended within the tank. Solved chemical fertilizer
is supplied to the root region of the plant using irrigation water.

• Applications
•Chemical fertilization applications by pressure agricultural irrigation systems
•Pesticide administration by pressure agricultural irrigation systems

• Features
•It provides ease of use and of maintenance due to simple structure.
•Pre-painting phosphorization is performed for maximum resistance against corrosion and chemical solution.
•It has long economic life based on Epoxy – Polyester coating.
•It operates based on line pressure of the system.

asbir.com.tr 35
 FILTRATION SYSTEMS
® FERTILIZER TANK 5000 SERIES

• Material List

Part No Part Name Material

1 Body St37-2

2 Lid Seal NBR/EPDM

3 Lid GGG40/50

4 Arm GGG40/50

5 Air Vent Ms58+AISI 302

• Dimensions

ØD H L Capacity
Model
mm inch mm inch mm inch liter

V5060 380 15,0 794 31,3 - - 60

Vertical

V5100 450 17,7 1054 41,5 - - 100

V5200 600 23,6 1200 47,2 - - 200

H5100 450 17,7 750 29,5 866 34,1 100

Horizontal

H5200 600 23,6 894 35,2 831 32,7 200

H5300 600 23,6 894 35,2 1081 42,6 300

H5400 600 23,6 894 35,2 1331 52,4 400

36 asbir.com.tr
FILTRATION SYSTEMS
BACK-FLUSHING CONTROL VALVES ®

• Description
Back-Flushing control valves are the 3-way control valves which are operated by line pressure or an external pneumatic pressure. Valve
works in filtration and back flushing mode as coordinated with filter elements in the system. Diaphragm-pilot valve assembly of valve
works as bidirectional. While valve is switching into backflushing mode in filtration mode, pilot valve changes its way and opens relief
way. It thereby prevents that fresh water is mixed with waste water and cleans filter elements in the best manner.

• Available Models

Model 21 Model 27 Model 28 Model 37 Model 38

H L Weight
Code Model A B C
mm mm kg lbs

2122 21 2" Threaded / BSP 2" Threaded / BSP 2" Threaded/ BSP 230 183 6,5 14,3

2732 27 3" Flanged / PN16 3" Flanged / PN16 2" Threaded/ BSP 285 241 20,0 44,1

2832 28 3" Grooved End 3" Grooved End 2" Threaded/ BSP 285 220 12,5 27,6

2743 27 4" Flanged / PN16 4" Flanged / PN16 3" Threaded/ BSP 293 280 31,0 68,3

2843 28 4" Grooved End 4" Grooved End 3" Threaded/ BSP 293 275 24,0 52,9

3732 37 3" Flanged / PN16 3" Flanged / PN16 2" Threaded/ BSP 275 270 18,0 39,7

3832 38 3" Grooved End 3" Grooved End 2" Threaded/ BSP 275 270 12,0 26,5

Model: 21 Model: 27 / 28 Model: 37 / 38

asbir.com.tr 37
 FILTRATION SYSTEMS
® BACK-FLUSHING CONTROL VALVES

• Main Parts

Model 21

Part No Part Name Material

1 Body GG25 (Cast Iron)

2 Diaphragm Natural Rubber Nylon Reinforced

3 Upper Bonnet GG25 (Cast Iron)

4 Stem AISI 304

5 Spring AISI 302

6 Seat Brass (Ms58)
7 Middle Bonnet GG25 (Cast Iron)

Model 27/28

Part No Part Name Material

1 Body GG25 (Cast Iron)

2 Upper Bonnet GG25 (Cast Iron)

3 Diaphragm Natural Rubber Nylon Reinforced

4 Stem AISI 304

5 Spring AISI 302

6 Seat Brass (Ms58)
7 Middle Bonnet GG25 (Cast Iron)

Model 37/38

Part No Part Name Material

1 Body GG25 (Cast Iron)

2 Diaphragm Natural Rubber Nylon Reinforced

3 Upper Bonnet GG25 (Cast Iron)

4 Stem AISI 304

5 Spring AISI 302

6 Wedge AISI 304 + Natural Rubber

38 asbir.com.tr
FILTRATION SYSTEMS
BACK-FLUSHING CONTROL VALVES ®

• Flow Characteristics
Filtration Mode
10

7
Head Loss (mwc)

6 2122
5 2732 / 2832
4
3732 / 3832
2743 / 2843
3

1
01 02 03 04 05 06 07 08 09 01 00 1101 20 130
Flow Rate (m3/h)

Back-Flushing Mode
10

7 2122
Head Loss (mwc)

6 2732 / 2832
3732 / 3832
5
2743 / 2843
4

1
01 02 03 04 05 06 07 08 09 01 00 1101 20 130
Flow Rate (m3/h)

2122 2732-2832 2743-2843 3732-3832

Model Back- Back- Back- Back-

Filtration Filtration Filtration Filtration
Flushing Flushing Flushing Flushing
Mode Mode Mode Mode
Mode Mode Mode Mode
Kv (m³/h @ 1 bar) 30 40 60 80 100 105 115 55
Cv (gpm @ 1 psi) 35 45 69 92 115 121 133 63
Recommended Flow (m³/h) 30 30 60 40 70 25 95 60
Max. Operation Pressure 16 bar

• Filtration • Back-Flushing

asbir.com.tr 39
 FILTRATION SYSTEMS
®
OTHER PRODUCTS

• HYDRAULIC CONTROL VALVES

800 SERIES
Asbir 800 series automatic hydraulic control valves are designed in the “Y” body model type so as to
show maximum resistance to cavitation under minimum head loss in high flow rates. Asbir 800 series
automatic hydraulic control valves are double-chamber diaphragm actuated and disc closed type. Valve
has a standard double control chamber.
Available Sizes: 2” (50 mm) - 16” (400 mm)
Available Connection Types: Flanged
Available Pressure Norms: PN16 - PN25 - PN40

600 SERIES
Asbir 600 series valves are the direct diaphragm closing automatic hydraulic control valves which work
with line pressure. It ensures easy and smooth flow with minimum pressure losses thanks to excellent
design of valve body and diaphragm.
Available Sizes: 1½” (40 mm) - 12” (300 mm)
Available Connection Types: Threaded, Flanged, Grooved End
Available Pressure Norms: PN10 - PN16 - PN25

500 SERIES
Asbir 500 series valves are direct diaphragm closing automatic hydraulic control valves which work
with line pressure. They ensure easy and smooth flow with minimum pressure losses thanks to excel-
lent design of valve body and diaphragm. Asbir 500 series hydraulic control valves are designed so that
it can be used in potable water force network, agricultural irrigation, filtration, applications by even an
unskilled personnel.
Available Sizes: 1½” (40 mm) - 4” (100 mm)
Available Connection Types: Threaded, Flanged

• AIR COMBINATION VALVE

AIR COMBINATION VALVES - AAV SERIES

Asbir AAV Series Automatic Air Release Valves are the valves that operate with line pressure. Asbir
AAV Series Automatic Air Release Valves are the air valves that provide the venting of the air during
filling and preventing of vacuum by taking air into the installation during emptying, releasing of the air
that accumulates in the installation during active operation with the help of pressure and that operates
in automatic manner.
Available Sizes: 2” (50 mm) - 8” (200 mm)
Available Connection Types: Flanged

40 asbir.com.tr
we care about the world
a s b i r. co m . t r
 ®

a s b i r . co m . t r

atlikarinca.net
Büyük Kayacık Mah. K.O.S. Bolgesi
İhsan Dede Cad. 12.Sk. No:8
Selçuklu / Konya / TURKEY

T: (+90).332 236 01 22 (Pbx)

F: (+90).332 236 01 18

[email protected]