Scribd
Upload
52 views4 pages

All-Products Esuprt Electronics Accessories Esuprt Electronics Accessories Monitor Esuprt Monitor S Series Dell-S3221qs-Monitor User's-Guide3 En-Us

The document provides disassembly instructions for a monitor. It lists 14 steps (S1-S14) to remove components like screws, cables, boards, frames, and capacitors. Tools required include Phillips head screwdrivers in multiple sizes, a penknife, and a soldering iron and absorber. The product contains printed circuit boards, an LCD greater than 100 cm2, electrolyte capacitors, and external cables that require separate treatment per EU Directive 75/442/EEC.

Uploaded by

kichutes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
52 views4 pages

All-Products Esuprt Electronics Accessories Esuprt Electronics Accessories Monitor Esuprt Monitor S Series Dell-S3221qs-Monitor User's-Guide3 En-Us

The document provides disassembly instructions for a monitor. It lists 14 steps (S1-S14) to remove components like screws, cables, boards, frames, and capacitors. Tools required include Phillips head screwdrivers in multiple sizes, a penknife, and a soldering iron and absorber. The product contains printed circuit boards, an LCD greater than 100 cm2, electrolyte capacitors, and external cables that require separate treatment per EU Directive 75/442/EEC.

Uploaded by

kichutes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

8.

Mechanical Instruction Use a Philips-head screwdriver to remove 4


8.1 Disassembly Procedures S4 screws for unlocking mechanisms.
S1 Turn off power (No.1~4 screw size=M4x10; Torque: 12±2kgf.cm)

S2 Push the button to remove the stand-base assy.

Wedge your fingers between the rear cover and


the middle bezel on the corners of the top side of
the monitor to release the rear cover, then use
S5 one hand to press the middle bezel, the other
hand to pull up carefully the rear cover in order of
arrow preference for unlocking mechanisms of
rear cover

S3 Remove the screw to remove the stand assy and


the base assy.

Tear off 5 pieces of aluminum foil and 2 pieces of


tapes. Disconnect the lamp cable from the
S6
connectors of the power board and panel
module. Use a Philips-head screwdriver to
remove 4 screws for unlocking the speakers.
(No.1~4 Screw size=M3x6, Torque: 4±1kgf.cm)

75
S8 Disconnect all of the cables.

S9 The Mainframe

Use a Philips-head screwdriver to remove 15


screws for unlocking the middle plastic bezel
S10
Remove the Mylar. Use a Philips-head with the whole unit, and then remove the
screwdriver to remove 12 screws for unlocking middle plastic bezel carefully.
S7
the main board and the adapter board (No.1~15 screw size=M3x4, Torque=3±0.5kgfxcm)

(No.1~11 screw size=D3x6, Torque: 6±1kgf.cm)

(No.12 screw size=M4x6, Torque: 6±1kgf.cm)

76
Use a Philips-head screwdriver to remove 3 Remove electrolyte capacitors (red mark)
S14
S11 screws to remove the key board. from printed circuit boards.
(No.1~3 screw size=M6x19, Torque=0.9±0.4kgf.cm)

Use a Philips-head screwdriver to remove 7


S12 screws for unlocking the BEZEL_BTM and the
Panel.
(No.1~7 screw size=M6x19, Torque=0.9±0.4kgf.cm) Take out bulk cap. Pins older with
soldering iron and absorber.

S13 The middle frame and the DECO bezel. Lift the bulk cap. up and away from the PCB

77
8.2 Product material information
The following substances, preparations, or components should be disposed of or

recovered separately from other WEEE in compliance with Article 4 of EU Council

Directive 75/442/EEC.

Capacitors / condensers (containing No used


PCB/PCT)
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface Product has printed circuit boards (with a
greater than 10 square cm) surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC No used
and HC
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100
cm2
External electric cable Product has external cables
Component contain refractory ceramic No used
fibers
Component contain radio-active No used
substances
Electrolyte capacitors (height Product has electrolyte capacitors
> 25mm, diameter > 25mm) (height > 25mm, diameter > 25mm)

8.3 Tools Required

List the type and size of the tools that would typically can be used to disassemble the product to

a point where components and materials requiring selective treatment can be removed.

Tool Description:

‐ Screwdriver (Phillip head) #1

‐ Screwdriver (Phillip head) #2

‐ Penknife

‐ Soldering iron and absorber

78

You might also like