WELDED MESH SLIDING GATE

(Finite Element Analysis)

ANALYSIS OF GATE

METHODOLOGY

In order to support the WELDED MESH SLIDING GATE, the geometry is proposed as indicated in the
drawing.
The Gate is modelled in STAAD.Pro and structural analysis is made. The wind load is applied on the
vertical structural members. The calculation of the design wind forces is based on the area of all
exposed members and elements projected on a plane normal to the wind direction. Forces shall be
assumed to act parallel to the wind direction. The calculation is done with 40% solid area of the
Welded Mesh as per the provided on the following page.
This calculation presents the design of the WELDED MESH SLIDING GATE.

Analysis Tool: STAAD Pro. V8i

Assumptions:
1. Gatepost is fixed at the bottom.
2. Wind speed considered is 50 m/s.
Stiffener Material Properties:
Minimum Specified Yield Strength = 310 MPa

References
ASCE 7-10 Minimum Design loads for Buildings and other
structures
International Building Code (IBC) 2018
CALCULATION

Solidity Ratio Calculation

Consider an area of 1m x 1m of Weldmesh fence
Length of wires in the mentioned area = 94 m
Diameter of wire = 4 mm
Solid area of Weldmesh fence = 94 x 0.004 = 0.376 m2
Solidity Ratio = 37.6 %
Considering 40 %

Weight of Weld mesh 14.12 x 2.9 = 380 kg (9.3 kg/m2)

Total Area of Gate= 14.12 x 2.9 = 40.95 m2
40% of the total area = 40.95 x 0.4 = 16.38 m2
Ar = 16.38 m2
Analytical Method of ASCE 7-10. The parameters used for the wind load are as follows:
Basic wind speed V, = 50 m/s
Exposure category: D
Topographical factor (Kzt) = 0.95
Directionality factor (Kd) = 0.85
Exposure pressure coefficient Kz = 1.03

Wind pressure is calculated as-

P = 0.613 x Kz x Kzt x Kd x V2 (N/m2)
Where P = Wind Pressure
P = 0.613 x 0.85 x 0.95 x 1.03 x 502
P = 1274.6 N/m2

Now Wind load is calculated as

Fw = P x G x Ar x Cf
Where Fw = Wind load
G = Gust effect factor (G = 0 .85 for 3 sec gust)
Cf = Force Coefficient = 1.3 (Ref. Fig 29.5-2, ASCE 7-10)
Fw = 1274.6 x 0.85 x 16.38 x 1.3 N
Fw = 23070 N
= 23070/68.46 = 337 N/m (Member load)
 Job No Sheet No Rev
1
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Job Information
Engineer Checked Approved

Name:
Date: 17-Feb-22

Structure Type SPACE FRAME

Number of Nodes 65 Highest Node 72

Number of Elements 87 Highest Beam 98

Number of Basic Load Cases 2

Number of Combination Load Cases 1

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DEAD LOAD

Primary 2 WIND LOAD
Combination 3 COMBINATION LOAD CASE 3

3D Rendered View (Input data was modified after picture taken)

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 19
 Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Nodes
Node X Y Z
(m) (m) (m)
1 0.000 0.000 0.000
2 0.000 2.900 0.000
3 14.120 0.000 0.000
4 14.120 2.900 0.000
9 0.000 1.450 0.000
12 14.120 1.450 0.000
13 0.932 2.900 0.000
14 1.765 0.000 0.000
15 3.529 0.000 0.000
16 5.294 0.000 0.000
17 7.059 0.000 0.000
18 8.823 0.000 0.000
19 1.765 2.900 0.000
20 3.529 2.900 0.000
21 5.294 2.900 0.000
22 7.059 2.900 0.000
23 8.823 2.900 0.000
25 8.823 1.450 0.000
26 5.294 1.450 0.000
27 7.059 1.450 0.000
28 3.529 1.450 0.000
29 1.765 1.450 0.000
30 0.932 0.000 0.000
31 0.000 0.500 0.000
32 0.000 1.000 0.000
33 0.000 0.500 -0.500
34 1.765 0.500 0.000
35 1.765 1.000 0.000
36 1.765 0.500 -0.500
37 3.529 0.500 0.000
38 3.529 1.000 0.000
39 3.530 0.500 -0.500
40 5.294 0.500 0.000
41 5.294 1.000 0.000
42 5.295 0.500 -0.500
43 7.060 0.500 0.000
44 7.060 1.000 0.000
45 7.060 0.500 -0.500
46 8.825 0.500 0.000
47 8.825 1.000 0.000
48 8.825 0.500 -0.500
49 1.765 0.000 -0.500
50 8.825 0.000 -0.500
51 14.122 0.500 0.000
52 14.122 1.000 0.000

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 19
 Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Nodes Cont...
Node X Y Z
(m) (m) (m)
53 14.122 0.500 -0.500
54 10.590 0.000 0.000
55 10.590 2.900 0.000
56 10.590 1.450 0.000
57 10.592 0.500 0.000
58 10.592 1.000 0.000
59 10.592 0.500 -0.500
60 10.592 0.000 -0.500
61 12.355 0.000 0.000
62 12.355 2.900 0.000
63 12.355 1.450 0.000
64 12.357 0.500 0.000
65 12.357 1.000 0.000
66 12.357 0.500 -0.500
67 12.357 0.000 -0.500
68 14.122 0.000 -0.500
69 0.000 0.000 -0.500
70 3.530 0.000 -0.500
71 5.295 0.000 -0.500
72 7.060 0.000 -0.500

Beams
Beam Node A Node B Length Property 
(m) (degrees)
1 2 9 1.450 1 0
2 1 30 0.932 1 0
3 2 13 0.932 1 0
4 4 12 1.450 1 0
5 4 62 1.765 1 0
11 9 32 0.450 1 0
16 12 3 1.450 1 0
18 14 15 1.765 1 0
19 15 16 1.765 1 0
20 16 17 1.765 1 0
21 17 18 1.765 1 0
22 18 54 1.767 1 0
23 19 13 0.833 1 0
24 20 19 1.765 1 0
25 21 20 1.765 1 0
26 22 21 1.765 1 0
27 23 22 1.765 1 0
29 19 29 1.450 2 90
30 20 28 1.450 2 90

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 19
 Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beams Cont...
Beam Node A Node B Length Property 
(m) (degrees)
31 21 26 1.450 2 90
32 22 27 1.450 2 90
33 23 25 1.450 2 90
34 25 56 1.767 2 90
35 26 27 1.765 2 90
36 26 41 0.450 2 90
37 27 17 1.450 2 90
38 25 18 1.450 2 90
39 27 25 1.765 2 90
40 28 38 0.450 2 90
41 29 35 0.450 2 90
42 9 29 1.765 2 0
43 29 28 1.765 2 0
44 28 26 1.765 2 0
45 30 14 0.833 1 0
46 31 1 0.500 1 0
47 32 31 0.500 1 0
48 31 33 0.500 2 0
49 33 32 0.707 2 0
50 34 14 0.500 2 90
51 35 34 0.500 2 90
52 34 36 0.500 2 0
53 36 35 0.707 2 0
54 37 15 0.500 2 90
55 38 37 0.500 2 90
56 37 39 0.500 2 0
57 39 38 0.707 2 0
58 40 16 0.500 2 90
59 41 40 0.500 2 90
60 40 42 0.500 2 0
61 42 41 0.707 2 0
62 43 45 0.500 2 0
63 45 44 0.707 2 0
64 46 48 0.500 2 0
65 48 47 0.707 2 0
66 49 36 0.500 2 0
67 48 50 0.500 2 0
68 33 36 1.765 2 0
69 36 39 1.765 2 0
70 39 42 1.765 2 0
71 42 45 1.765 2 0
72 45 48 1.765 2 0
73 51 53 0.500 2 0
74 53 52 0.707 2 0
75 48 59 1.767 2 0

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 19
 Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beams Cont...
Beam Node A Node B Length Property 
(m) (degrees)
76 54 61 1.765 1 0
77 55 23 1.767 1 0
78 56 63 1.765 2 90
79 59 66 1.765 2 0
80 55 56 1.450 2 90
81 56 54 1.450 2 90
82 57 59 0.500 2 0
83 59 58 0.707 2 0
84 59 60 0.500 2 0
85 61 3 1.765 1 0
86 62 55 1.765 1 0
87 63 12 1.765 2 90
88 66 53 1.765 2 0
89 62 63 1.450 2 90
90 63 61 1.450 2 90
91 64 66 0.500 2 0
92 66 65 0.707 2 0
93 66 67 0.500 2 0
94 53 68 0.500 2 0
95 69 33 0.500 2 0
96 70 39 0.500 2 0
97 71 42 0.500 2 0
98 72 45 0.500 2 0

62

55

23 12

63 52
22 53
56 65 51
21 68
66
25 58 64 3
20 67
59
27 47 57 61
19 60
48
13
26 44 46 54
2 50
45
28 41 43 18
42 72
29 38 40 17
39 71
9 35 37 16
36 70
32 34 15
Y 33 49
X 31 14
Z 69 30 Load 2
1
Whole Structure

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 19
 Job No Sheet No Rev
6
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

86 4

77 89

27 80 87
74
26 33 78 7316
88 94
92
25 32 34 9190
79 93
83
85
24 31 39 8281
75 84
65
23 76
30 35 6438
3 72 67
63
22
29 44 36 6237
71 98
61
43 40 59 21
1 60
70 97
57
42 41 55 58 20
56
69 96
53
11 51 54 19
52
68 66
49
47 50 18
48
Y 95
X 45
46 Load 2
Z 2

Whole Structure

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 TUB80805.0 14.700 137.000 137.000 210.937 STEEL
2 TUB80403.2 7.160 18.900 57.200 46.200 STEEL

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 - - Fixed Fixed - -
2 - - Fixed Fixed - -
3 - - Fixed Fixed - -
13 - - Fixed Fixed - -
14 - Fixed Fixed - - -
17 - Fixed Fixed - - -
30 - - Fixed Fixed - -
49 - Fixed Fixed - - -
61 - Fixed Fixed - - -
67 - Fixed Fixed - - -
72 - Fixed Fixed - - -

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 19
 Job No Sheet No Rev
7
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

R1 R2:ß 90.00

R1
R2:ß 90.00
R1

R2 R2:ß 90.00
R2:ß 90.00

R2
R2:ß 90.00 R2:ß 90.00
R1 R2 R2
R2 R2
R2
R2:ß 90.00 R2:ß 90.00 R2:ß 90.00
R2 R2
R2 R2
R2
R1 R2:ß 90.00 R2:ß 90.00 R1
R2
R2 R2
R2
R1 R2:ß 90.00 R1
R2
R2
R1
R1
R1

Whole Structure

Primary Load Cases

Number Name Type

1 DEAD LOAD Dead

2 WIND LOAD Wind

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 COMBINATION LOAD CASE 3 1 DEAD LOAD 1.00

2 WIND LOAD 1.00

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 7 of 19
 Job No Sheet No Rev
8
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

-0.337 kN/m
-0.337 kN/m
-0.337 kN/m
-0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m
-0.337 kN/m
-0.337 kN/m -0.337 kN/m
-0.337 kN/m
-0.337 kN/m -0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m -0.337 kN/m -0.337 kN/m

Y
X -0.337 kN/m -0.337 kN/m -0.337 kN/m -0.337 kN/m
Z Load 2
-0.337 kN/m -0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m

-0.337 kN/m
-0.337 kN/m

Whole Structure

-0.270 kN/m
-0.270 kN/m
-0.270 kN/m
-0.270 kN/m -0.337 kN/m
-0.270 kN/m -0.337 kN/m
-0.270 kN/m -0.337 kN/m
-0.270 kN/m -0.337 kN/m -0.337 kN/m
-0.270 kN/m -0.337 kN/m -0.337 kN/m
-0.270 kN/m -0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m
-0.337 kN/m
-0.337 kN/m -0.337 kN/m
-0.337 kN/m
-0.337 kN/m -0.337 kN/m -0.337 kN/m

-0.337 kN/m -0.337 kN/m -0.337 kN/m -0.337 kN/m

Y
X -0.337 kN/m -0.337 kN/m -0.337 kN/m -0.337 kN/m
Z Load 3
-0.337 kN/m -0.337 kN/m -0.337 kN/m
-0.337 kN/m -0.337 kN/m
-0.337 kN/m
-0.337 kN/m
Whole Structure

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 8 of 19
 Job No Sheet No Rev
9
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

1 DEAD LOAD : Beam Loads

Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
3 UNI kN/m GY -0.270 - - - -
5 UNI kN/m GY -0.270 - - - -
23 UNI kN/m GY -0.270 - - - -
24 UNI kN/m GY -0.270 - - - -
25 UNI kN/m GY -0.270 - - - -
26 UNI kN/m GY -0.270 - - - -
27 UNI kN/m GY -0.270 - - - -
77 UNI kN/m GY -0.270 - - - -
86 UNI kN/m GY -0.270 - - - -

1 DEAD LOAD : Selfweight

Direction Factor Assigned Geometry

Y -1.000 1 - 5, 11, 16, 18 - 27, 29 - 98

2 WIND LOAD : Beam Loads

Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
1 UNI kN/m GZ -0.337 - - - -
2 UNI kN/m GZ -0.337 - - - -
3 UNI kN/m GZ -0.337 - - - -
4 UNI kN/m GZ -0.337 - - - -
5 UNI kN/m GZ -0.337 - - - -
11 UNI kN/m GZ -0.337 - - - -
16 UNI kN/m GZ -0.337 - - - -
18 UNI kN/m GZ -0.337 - - - -
19 UNI kN/m GZ -0.337 - - - -
20 UNI kN/m GZ -0.337 - - - -
21 UNI kN/m GZ -0.337 - - - -
22 UNI kN/m GZ -0.337 - - - -
23 UNI kN/m GZ -0.337 - - - -
24 UNI kN/m GZ -0.337 - - - -
25 UNI kN/m GZ -0.337 - - - -
26 UNI kN/m GZ -0.337 - - - -
27 UNI kN/m GZ -0.337 - - - -
29 UNI kN/m GZ -0.337 - - - -
30 UNI kN/m GZ -0.337 - - - -
31 UNI kN/m GZ -0.337 - - - -
32 UNI kN/m GZ -0.337 - - - -
33 UNI kN/m GZ -0.337 - - - -
34 UNI kN/m GZ -0.337 - - - -
35 UNI kN/m GZ -0.337 - - - -

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 9 of 19
 Job No Sheet No Rev
10
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

2 WIND LOAD : Beam Loads Cont...

Beam Type Direction Fa Da Fb Db Ecc.
(m) (m)
36 UNI kN/m GZ -0.337 - - - -
37 UNI kN/m GZ -0.337 - - - -
38 UNI kN/m GZ -0.337 - - - -
39 UNI kN/m GZ -0.337 - - - -
40 UNI kN/m GZ -0.337 - - - -
41 UNI kN/m GZ -0.337 - - - -
42 UNI kN/m GZ -0.337 - - - -
43 UNI kN/m GZ -0.337 - - - -
44 UNI kN/m GZ -0.337 - - - -
45 UNI kN/m GZ -0.337 - - - -
46 UNI kN/m GZ -0.337 - - - -
47 UNI kN/m GZ -0.337 - - - -
50 UNI kN/m GZ -0.337 - - - -
51 UNI kN/m GZ -0.337 - - - -
54 UNI kN/m GZ -0.337 - - - -
55 UNI kN/m GZ -0.337 - - - -
58 UNI kN/m GZ -0.337 - - - -
59 UNI kN/m GZ -0.337 - - - -
76 UNI kN/m GZ -0.337 - - - -
77 UNI kN/m GZ -0.337 - - - -
78 UNI kN/m GZ -0.337 - - - -
80 UNI kN/m GZ -0.337 - - - -
81 UNI kN/m GZ -0.337 - - - -
85 UNI kN/m GZ -0.337 - - - -
86 UNI kN/m GZ -0.337 - - - -
87 UNI kN/m GZ -0.337 - - - -
89 UNI kN/m GZ -0.337 - - - -
90 UNI kN/m GZ -0.337 - - - -

Node Displacement Summary

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 72 3:COMBINATION LOAD CASE 3 0.000
9.912 0.000 9.912 -0.047 -0.004 0.012
Min X 44 2:WIND LOAD -4.305 25.044 -50.367 56.414 -0.050 -0.003 0.012
Max Y 46 2:WIND LOAD 2.733 36.706 -22.679 43.234 -0.050 -0.001 0.002
Min Y 71 3:COMBINATION LOAD
5.370
CASE 3-20.422 -4.447 21.580 -0.044 0.004 0.003
Max Z 52 1:DEAD LOAD 1.574 -8.263 12.417 14.998 0.012 -0.000 -0.002
Min Z 23 2:WIND LOAD 5.753 -1.120 -199.698 199.784 -0.060 0.001 0.000
Max rX 52 1:DEAD LOAD 1.574 -8.263 12.417 14.998 0.012 -0.000 -0.002
Min rX 25 2:WIND LOAD 5.493 -1.120 -106.516 106.663 -0.067 0.002 -0.000
Max rY 20 2:WIND LOAD 5.752 1.804 -71.136 71.391 -0.023 0.037 0.001
Min rY 4 2:WIND LOAD 5.753 -0.077 -85.051 85.245 -0.044 -0.031 -0.000
Max rZ 43 2:WIND LOAD 1.705 25.044 -25.318 35.652 -0.050 -0.003 0.012

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 10 of 19
 Job No Sheet No Rev
11
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Node Displacement Summary Cont...

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Min rZ 68 3:COMBINATION LOAD
0.007
CASE 3-12.867 -1.505 12.955 -0.037 0.001 -0.008
Max Rst 23 2:WIND LOAD 5.753 -1.120 -199.698 199.784 -0.060 0.001 0.000

Beam Combined Axial and Bending Stresses Summary

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
1 1:DEAD LOAD 1.450 3.709 0.000 3 -3.710 0.000 1
2:WIND LOAD 1.450 9.280 1.450 3 -9.029 1.450 1
3:COMBINATION LOAD
1.450
CASE 3 7.884 1.329 3 -7.430 1.329 1
2 1:DEAD LOAD 0.932 5.922 0.000 1 -5.589 0.000 3
2:WIND LOAD 0.932 17.288 0.000 2 -19.115 0.000 1
3:COMBINATION LOAD
0.932
CASE 3 11.699 0.000 2 -13.193 0.000 1
3 1:DEAD LOAD 0.932 3.722 0.000 1 -3.890 0.000 3
2:WIND LOAD 0.932 199.254 0.932 1 -198.897 0.932 2
3:COMBINATION LOAD
0.932
CASE 196.571
3 0.932 1 -196.381 0.932 2
4 1:DEAD LOAD 1.450 4.191 0.000 1 -4.250 0.000 3
2:WIND LOAD 1.450 106.949 1.450 1 -107.017 1.450 2
3:COMBINATION LOAD
1.450
CASE 107.019
3 1.450 1 -106.924 1.450 2
5 1:DEAD LOAD 1.765 15.526 1.765 3 -15.665 1.765 1
2:WIND LOAD 1.765 39.785 1.765 4 -39.848 1.765 2
3:COMBINATION LOAD
1.765
CASE 3 55.311 1.765 4 -55.513 1.765 2
11 1:DEAD LOAD 0.450 2.144 0.000 3 -2.087 0.000 1
2:WIND LOAD 0.450 13.746 0.000 3 -13.530 0.000 1
3:COMBINATION LOAD
0.450
CASE 315.836 0.000 3 -15.562 0.000 1
16 1:DEAD LOAD 1.450 6.122 1.450 3 -5.752 1.450 1
2:WIND LOAD 1.450 265.788 1.450 1 -265.822 1.450 2
3:COMBINATION LOAD
1.450
CASE 265.576
3 1.450 1 -265.240 1.450 2
18 1:DEAD LOAD 1.765 13.838 0.000 3 -13.644 0.000 1
2:WIND LOAD 1.765 36.075 0.000 1 -37.724 0.000 2
3:COMBINATION LOAD
1.765
CASE 323.756 0.000 1 -25.211 0.000 2
19 1:DEAD LOAD 1.765 7.283 1.029 2 -7.369 1.029 4
2:WIND LOAD 1.765 43.872 1.765 3 -44.352 1.765 1
3:COMBINATION LOAD
1.765
CASE 337.882 1.765 3 -38.449 1.765 1
20 1:DEAD LOAD 1.765 18.305 1.765 3 -18.153 1.765 1
2:WIND LOAD 1.765 88.402 1.765 1 -88.722 1.765 3
3:COMBINATION LOAD
1.765
CASE 375.816 1.765 1 -75.983 1.765 2
21 1:DEAD LOAD 1.765 18.410 0.000 3 -18.267 0.000 1
2:WIND LOAD 1.765 77.189 0.000 1 -77.712 0.000 2
3:COMBINATION LOAD
1.765
CASE 372.608 0.000 1 -72.988 0.000 2
22 1:DEAD LOAD 1.767 8.050 1.031 1 -8.051 1.031 3
2:WIND LOAD 1.767 41.963 0.884 2 -42.414 0.884 4
3:COMBINATION LOAD
1.767
CASE 349.885 0.884 2 -50.336 0.884 4

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 11 of 19
 Job No Sheet No Rev
12
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
23 1:DEAD LOAD 0.833 14.515 0.000 3 -14.682 0.000 1
2:WIND LOAD 0.833 199.254 0.833 2 -198.897 0.833 1
3:COMBINATION LOAD
0.833
CASE 196.571
3 0.833 2 -196.381 0.833 1
24 1:DEAD LOAD 1.765 15.771 1.765 3 -15.868 1.765 1
2:WIND LOAD 1.765 141.329 1.765 2 -141.136 1.765 4
3:COMBINATION LOAD
1.765
CASE 136.510
3 1.765 2 -136.414 1.765 1
25 1:DEAD LOAD 1.765 8.548 0.735 2 -8.504 0.735 4
2:WIND LOAD 1.765 73.560 0.000 1 -73.798 0.000 2
3:COMBINATION LOAD
1.765
CASE 368.623 0.000 1 -68.816 0.000 2
26 1:DEAD LOAD 1.765 20.251 0.000 3 -20.335 0.000 1
2:WIND LOAD 1.765 96.266 0.000 1 -96.424 0.000 2
3:COMBINATION LOAD
1.765
CASE 384.503 0.000 1 -84.746 0.000 2
27 1:DEAD LOAD 1.765 20.391 1.765 3 -20.466 1.765 1
2:WIND LOAD 1.765 94.548 0.441 1 -94.443 0.441 3
3:COMBINATION LOAD
1.765
CASE 100.133
3 0.000 1 -100.103 0.000 2
29 1:DEAD LOAD 1.450 6.208 0.000 1 -2.260 0.000 2
2:WIND LOAD 1.450 32.368 1.450 4 -33.466 1.450 2
3:COMBINATION LOAD
1.450
CASE 330.813 1.450 4 -27.740 1.450 2
30 1:DEAD LOAD 1.450 9.529 0.000 1 -8.710 0.000 2
2:WIND LOAD 1.450 48.771 0.000 3 -49.688 0.000 1
3:COMBINATION LOAD
1.450
CASE 340.331 0.000 3 -40.429 0.000 1
31 1:DEAD LOAD 1.450 9.511 0.000 2 -9.097 0.000 1
2:WIND LOAD 1.450 47.176 0.000 1 -43.540 0.000 3
3:COMBINATION LOAD
1.450
CASE 345.525 0.000 1 -41.475 0.000 3
32 1:DEAD LOAD 1.450 3.455 0.000 1
2:WIND LOAD 1.450 75.665 0.000 1 -78.176 0.000 3
3:COMBINATION LOAD
1.450
CASE 378.097 0.000 1 -75.847 0.000 3
33 1:DEAD LOAD 1.450 10.577 0.000 1 -10.080 0.000 2
2:WIND LOAD 1.450 50.090 0.000 1 -49.972 0.000 3
3:COMBINATION LOAD
1.450
CASE 357.087 0.000 1 -56.472 0.000 3
34 1:DEAD LOAD 1.767 1.784 0.000 2 -1.917 0.000 1
2:WIND LOAD 1.767 68.829 0.442 1 -68.097 0.442 3
3:COMBINATION LOAD
1.767
CASE 369.331 0.589 1 -68.732 0.589 3
35 1:DEAD LOAD 1.765 12.925 1.765 2 -13.064 1.765 1
2:WIND LOAD 1.765 46.505 1.765 1 -45.525 1.765 3
3:COMBINATION LOAD
1.765
CASE 333.742 1.765 1 -32.901 1.765 3
36 1:DEAD LOAD 0.450 10.128 0.000 2 -9.385 0.000 1
2:WIND LOAD 0.450 52.050 0.450 4 -47.514 0.450 2
3:COMBINATION LOAD
0.450
CASE 357.015 0.450 4 -51.667 0.450 2
37 1:DEAD LOAD 1.450 4.075 0.000 1
2:WIND LOAD 1.450 102.107 1.450 3 -105.111 1.450 1
3:COMBINATION LOAD
1.450
CASE 105.453
3 1.450 3 -102.292 1.450 1
38 1:DEAD LOAD 1.450 10.686 1.450 2 -9.807 1.450 1
2:WIND LOAD 1.450 77.548 1.450 3 -77.705 1.450 1

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 12 of 19
 Job No Sheet No Rev
13
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
3:COMBINATION LOAD
1.450
CASE 378.361 1.450 3 -77.639 1.450 1
39 1:DEAD LOAD 1.765 13.659 0.000 2 -13.798 0.000 1
2:WIND LOAD 1.765 59.526 1.765 1 -58.668 1.765 3
3:COMBINATION LOAD
1.765
CASE 369.624 1.765 1 -68.905 1.765 3
40 1:DEAD LOAD 0.450 9.860 0.000 1 -9.456 0.000 2
2:WIND LOAD 0.450 54.524 0.450 2 -55.629 0.450 4
3:COMBINATION LOAD
0.450
CASE 353.426 0.450 2 -54.058 0.450 4
41 1:DEAD LOAD 0.450 7.852 0.000 1 -2.192 0.000 2
2:WIND LOAD 0.450 125.988 0.450 3 -127.146 0.450 1
3:COMBINATION LOAD
0.450
CASE 128.433
3 0.450 3 -123.862 0.450 1
42 1:DEAD LOAD 1.765 12.659 1.765 3 -12.852 1.765 1
2:WIND LOAD 1.765 83.439 1.765 1 -87.351 1.765 2
3:COMBINATION LOAD
1.765
CASE 388.867 1.765 4 -92.972 1.765 2
43 1:DEAD LOAD 1.765 18.283 0.000 3 -18.343 0.000 1
2:WIND LOAD 1.765 99.123 0.000 1 -101.799 0.000 2
3:COMBINATION LOAD
1.765
CASE 102.089
3 0.000 1 -104.825 0.000 2
44 1:DEAD LOAD 1.765 5.043 0.000 1 -4.902 0.000 3
2:WIND LOAD 1.765 25.188 1.324 3 -23.288 1.324 1
3:COMBINATION LOAD
1.765
CASE 324.553 1.471 3 -22.512 1.471 1
45 1:DEAD LOAD 0.833 12.498 0.833 4 -12.164 0.833 2
2:WIND LOAD 0.833 38.159 0.833 1 -39.986 0.833 3
3:COMBINATION LOAD
0.833
CASE 333.318 0.833 4 -34.811 0.833 2
46 1:DEAD LOAD 0.500 5.552 0.500 1 -5.235 0.500 3
2:WIND LOAD 0.500 13.338 0.000 1 -13.737 0.000 3
3:COMBINATION LOAD
0.500
CASE 315.246 0.000 1 -15.405 0.000 3
47 1:DEAD LOAD 0.500 2.530 0.500 1 -2.313 0.500 3
2:WIND LOAD 0.500 13.527 0.500 2 -13.912 0.500 4
3:COMBINATION LOAD
0.500
CASE 316.057 0.500 2 -16.225 0.500 4
48 1:DEAD LOAD 0.500 2.970 0.000 2 -3.023 0.000 1
2:WIND LOAD 0.500 59.542 0.000 1 -59.399 0.000 2
3:COMBINATION LOAD
0.500
CASE 356.519 0.000 1 -56.429 0.000 2
49 1:DEAD LOAD 0.707 3.607 0.000 1 -3.523 0.000 2
2:WIND LOAD 0.707 39.368 0.707 2 -37.769 0.707 1
3:COMBINATION LOAD
0.707
CASE 339.291 0.707 2 -37.685 0.707 1
50 1:DEAD LOAD 0.500 8.704 0.500 3 -2.597 0.500 1
2:WIND LOAD 0.500 108.084 0.000 1 -141.274 0.000 3
3:COMBINATION LOAD
0.500
CASE 3
110.587 0.000 1 -137.746 0.000 3
51 1:DEAD LOAD 0.500 5.034 0.500 2
2:WIND LOAD 0.500 72.612 0.000 3 -97.043 0.000 1
3:COMBINATION LOAD
0.500
CASE 374.647 0.000 3 -93.299 0.000 1
52 1:DEAD LOAD 0.500 2.524 0.500 2 -2.516 0.500 4
2:WIND LOAD 0.500 61.260 0.000 1 -76.157 0.000 3
3:COMBINATION LOAD
0.500
CASE 361.347 0.000 1 -76.236 0.000 3
53 1:DEAD LOAD 0.707 3.684 0.000 2 -3.641 0.000 1

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 13 of 19
 Job No Sheet No Rev
14
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
2:WIND LOAD 0.707 87.934 0.707 1 -59.752 0.707 3
3:COMBINATION LOAD
0.707
CASE 387.894 0.707 1 -59.745 0.707 3
54 1:DEAD LOAD 0.500 11.545 0.500 2 -10.994 0.500 1
2:WIND LOAD 0.500 63.954 0.500 1 -63.230 0.500 3
3:COMBINATION LOAD
0.500
CASE 353.271 0.500 1 -51.996 0.500 3
55 1:DEAD LOAD 0.500 4.654 0.500 2 -4.213 0.500 4
2:WIND LOAD 0.500 57.344 0.000 2 -56.287 0.000 1
3:COMBINATION LOAD
0.500
CASE 355.128 0.000 2 -53.706 0.000 1
56 1:DEAD LOAD 0.500 3.371 0.500 2 -3.548 0.500 1
2:WIND LOAD 0.500 12.678 0.500 1 -10.923 0.500 2
3:COMBINATION LOAD
0.500
CASE 3 9.130 0.500 1 -7.552 0.500 2
57 1:DEAD LOAD 0.707 6.145 0.000 2 -5.901 0.000 1
2:WIND LOAD 0.707 93.755 0.000 2 -95.929 0.000 1
3:COMBINATION LOAD
0.707
CASE 399.669 0.000 2 -101.599 0.000 1
58 1:DEAD LOAD 0.500 12.211 0.500 1 -11.236 0.500 3
2:WIND LOAD 0.500 30.908 0.000 1 -34.841 0.000 3
3:COMBINATION LOAD
0.500
CASE 332.958 0.500 4 -35.916 0.500 2
59 1:DEAD LOAD 0.500 6.859 0.500 1 -6.285 0.500 3
2:WIND LOAD 0.500 40.240 0.000 3 -44.816 0.000 1
3:COMBINATION LOAD
0.500
CASE 343.255 0.000 3 -47.332 0.000 1
60 1:DEAD LOAD 0.500 4.092 0.500 1 -4.418 0.500 3
2:WIND LOAD 0.500 15.718 0.500 2 -23.361 0.500 4
3:COMBINATION LOAD
0.500
CASE 316.999 0.500 2 -24.969 0.500 4
61 1:DEAD LOAD 0.707 9.750 0.000 1 -9.134 0.000 2
2:WIND LOAD 0.707 52.665 0.707 1 -40.080 0.707 3
3:COMBINATION LOAD
0.707
CASE 353.858 0.707 1 -40.733 0.707 3
62 1:DEAD LOAD 0.500 0.481 0.500 3 -0.481 0.500 1
2:WIND LOAD 0.500 0.000 0.458 1 -0.000 0.458 3
3:COMBINATION LOAD
0.500
CASE 3 0.481 0.500 3 -0.481 0.500 1
63 1:DEAD LOAD 0.707 0.718 0.000 3 -0.642 0.000 1
2:WIND LOAD 0.707 0.000 0.000 3 -0.000 0.000 1
3:COMBINATION LOAD
0.707
CASE 3 0.718 0.000 3 -0.642 0.000 1
64 1:DEAD LOAD 0.500 0.481 0.500 3 -0.481 0.500 1
2:WIND LOAD 0.500 0.000 0.458 1
3:COMBINATION LOAD
0.500
CASE 3 0.481 0.500 3 -0.481 0.500 1
65 1:DEAD LOAD 0.707 0.718 0.000 3 -0.642 0.000 1
2:WIND LOAD 0.707 0.000 0.000 3 -0.000 0.000 1
3:COMBINATION LOAD
0.707
CASE 3 0.718 0.000 3 -0.642 0.000 1
66 1:DEAD LOAD 0.500 0.957 0.500 1
2:WIND LOAD 0.500 95.294 0.500 2 -59.906 0.500 1
3:COMBINATION LOAD
0.500
CASE 395.448 0.500 2 -58.949 0.500 1
67 1:DEAD LOAD 0.500 0.000 0.500 1 -0.038 0.000 1
2:WIND LOAD 0.500 0.000 0.000 1 -0.000 0.000 2
3:COMBINATION LOAD
0.500
CASE 3 0.000 0.500 1 -0.038 0.000 1

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 14 of 19
 Job No Sheet No Rev
15
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
68 1:DEAD LOAD 1.765 10.953 1.765 3 -11.101 1.765 1
2:WIND LOAD 1.765 82.500 1.765 4 -75.571 1.765 2
3:COMBINATION LOAD
1.765
CASE 392.698 1.765 4 -85.917 1.765 2
69 1:DEAD LOAD 1.765 14.401 0.000 3 -14.540 0.000 1
2:WIND LOAD 1.765 111.625 0.000 3 -105.960 0.000 1
3:COMBINATION LOAD
1.765
CASE 125.300
3 0.000 3 -119.774 0.000 1
70 1:DEAD LOAD 1.765 5.743 0.883 2 -5.798 0.883 4
2:WIND LOAD 1.765 142.134 1.765 2 -142.560 1.765 4
3:COMBINATION LOAD
1.765
CASE 146.347
3 1.765 2 -146.827 1.765 4
71 1:DEAD LOAD 1.765 17.250 1.765 3 -17.250 1.765 1
2:WIND LOAD 1.765 183.005 0.000 1 -183.005 0.000 3
3:COMBINATION LOAD
1.765
CASE 197.138
3 0.000 1 -197.138 0.000 3
72 1:DEAD LOAD 1.765 17.250 0.000 3 -17.250 0.000 1
2:WIND LOAD 1.765 61.532 0.000 3 -61.532 0.000 1
3:COMBINATION LOAD
1.765
CASE 378.782 0.000 3 -78.782 0.000 1
73 1:DEAD LOAD 0.500 0.481 0.500 3 -0.481 0.500 1
2:WIND LOAD 0.500 0.000 0.500 1
3:COMBINATION LOAD
0.500
CASE 3 0.481 0.500 3 -0.481 0.500 1
74 1:DEAD LOAD 0.707 0.718 0.000 3 -0.642 0.000 1
2:WIND LOAD 0.707 0.000 0.000 1 -0.000 0.000 3
3:COMBINATION LOAD
0.707
CASE 3 0.718 0.000 3 -0.642 0.000 1
75 1:DEAD LOAD 1.767 8.737 0.736 1 -8.737 0.736 3
2:WIND LOAD 1.767 41.029 0.000 3 -41.029 0.000 1
3:COMBINATION LOAD
1.767
CASE 3 34.811 0.000 3 -34.811 0.000 1
76 1:DEAD LOAD 1.765 15.135 1.765 3 -15.003 1.765 1
2:WIND LOAD 1.765 57.732 1.765 1 -58.025 1.765 2
3:COMBINATION LOAD
1.765
CASE 372.750 1.765 4 -72.912 1.765 2
77 1:DEAD LOAD 1.767 9.020 0.884 2 -8.954 0.884 4
2:WIND LOAD 1.767 94.529 1.767 1 -94.435 1.767 3
3:COMBINATION LOAD
1.767
CASE 399.844 1.325 1 -99.685 1.325 3
78 1:DEAD LOAD 1.765 13.986 1.765 2 -14.123 1.765 1
2:WIND LOAD 1.765 65.118 0.000 1 -64.502 0.000 3
3:COMBINATION LOAD
1.765
CASE 375.996 0.000 1 -75.516 0.000 3
79 1:DEAD LOAD 1.765 17.580 1.765 3 -17.580 1.765 1
2:WIND LOAD 1.765 20.503 0.000 3 -20.503 0.000 1
3:COMBINATION LOAD
1.765
CASE 317.580 1.765 3 -17.580 1.765 1
80 1:DEAD LOAD 1.450 9.538 0.000 2 -9.027 0.000 1
2:WIND LOAD 1.450 34.612 0.000 1 -34.628 0.000 3
3:COMBINATION LOAD
1.450
CASE 343.980 0.000 1 -43.484 0.000 3
81 1:DEAD LOAD 1.450 9.818 1.450 1 -8.987 1.450 2
2:WIND LOAD 1.450 89.142 1.450 4 -89.157 1.450 2
3:COMBINATION LOAD
1.450
CASE 398.819 1.450 4 -98.003 1.450 2
82 1:DEAD LOAD 0.500 0.481 0.500 3 -0.481 0.500 1
2:WIND LOAD 0.500 0.000 0.458 3 -0.000 0.458 1

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 15 of 19
 Job No Sheet No Rev
16
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
3:COMBINATION LOAD
0.500
CASE 3 0.481 0.500 3 -0.481 0.500 1
83 1:DEAD LOAD 0.707 0.718 0.000 3 -0.642 0.000 1
2:WIND LOAD 0.707 0.000 0.707 1 -0.000 0.707 3
3:COMBINATION LOAD
0.707
CASE 3 0.718 0.000 3 -0.642 0.000 1
84 1:DEAD LOAD 0.500 0.000 0.500 1 -0.038 0.000 1
2:WIND LOAD 0.500 0.000 0.000 3 -0.000 0.000 1
3:COMBINATION LOAD
0.500
CASE 3 -0.038 0.000 1
85 1:DEAD LOAD 1.765 13.850 0.000 3 -13.644 0.000 1
2:WIND LOAD 1.765 69.470 0.000 1 -69.645 0.000 2
3:COMBINATION LOAD
1.765
CASE 383.095 0.000 1 -83.063 0.000 2
86 1:DEAD LOAD 1.765 16.943 0.000 3 -17.008 0.000 1
2:WIND LOAD 1.765 80.717 1.765 1 -80.723 1.765 2
3:COMBINATION LOAD
1.765
CASE 388.131 1.765 1 -88.203 1.765 3
87 1:DEAD LOAD 1.765 7.118 0.000 2 -7.258 0.000 1
2:WIND LOAD 1.765 59.885 1.765 3 -59.396 1.765 1
3:COMBINATION LOAD
1.765
CASE 358.324 1.765 3 -57.975 1.765 1
88 1:DEAD LOAD 1.765 17.580 0.000 3 -17.580 0.000 1
2:WIND LOAD 1.765 0.000 0.000 1 -0.000 0.000 2
3:COMBINATION LOAD
1.765
CASE 317.580 0.000 3 -17.580 0.000 1
89 1:DEAD LOAD 1.450 7.045 0.000 2 -2.768 0.000 1
2:WIND LOAD 1.450 30.613 1.450 3 -30.204 1.450 1
3:COMBINATION LOAD
1.450
CASE 336.158 1.450 4 -31.249 1.450 2
90 1:DEAD LOAD 1.450 7.883 1.450 1 -2.346 1.450 2
2:WIND LOAD 1.450 135.356 1.450 4 -134.829 1.450 2
3:COMBINATION LOAD
1.450
CASE 142.986
3 1.450 4 -136.923 1.450 2
91 1:DEAD LOAD 0.500 0.481 0.500 3 -0.481 0.500 1
2:WIND LOAD 0.500 0.000 0.500 1 -0.000 0.500 3
3:COMBINATION LOAD
0.500
CASE 3 0.481 0.500 3 -0.481 0.500 1
92 1:DEAD LOAD 0.707 0.718 0.000 3 -0.642 0.000 1
2:WIND LOAD 0.707 0.000 0.000 3 -0.000 0.000 1
3:COMBINATION LOAD
0.707
CASE 3 0.718 0.000 3 -0.642 0.000 1
93 1:DEAD LOAD 0.500 0.798 0.000 1
2:WIND LOAD 0.500 0.331 0.000 1 -0.752 0.000 2
3:COMBINATION LOAD
0.500
CASE 3 1.129 0.000 1 -0.151 0.000 2
94 1:DEAD LOAD 0.500 0.000 0.500 1 -0.038 0.000 1
2:WIND LOAD 0.500 0.000 0.000 3 -0.000 0.000 1
3:COMBINATION LOAD
0.500
CASE 3 0.000 0.500 2 -0.038 0.000 1
95 1:DEAD LOAD 0.500 -0.038 0.500 1
2:WIND LOAD 0.500 0.000 0.500 1 -0.000 0.500 3
3:COMBINATION LOAD
0.500
CASE 3 0.000 0.000 3 -0.038 0.500 1
96 1:DEAD LOAD 0.500 0.000 0.000 2 -0.038 0.500 1
2:WIND LOAD 0.500 -0.000 0.500 1
3:COMBINATION LOAD
0.500
CASE 3 -0.038 0.500 1
97 1:DEAD LOAD 0.500 0.000 0.000 1 -0.038 0.500 1

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 16 of 19
 Job No Sheet No Rev
17
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Beam Combined Axial and Bending Stresses Summary Cont...

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
2:WIND LOAD 0.500 0.000 0.000 2 -0.000 0.000 1
3:COMBINATION LOAD
0.500
CASE 3 0.000 0.000 1 -0.038 0.500 1
98 1:DEAD LOAD 0.500 2.551 0.500 2 -0.995 0.500 1
2:WIND LOAD 0.500 15.380 0.500 2 -10.412 0.500 1
3:COMBINATION LOAD
0.500
CASE 317.931 0.500 2 -11.407 0.500 1

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000
Min FX 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000
Max FY 49 3:COMBINATION LOAD
0.000
CASE 313.094 1.459 0.000 0.000 0.000
Min FY 14 2:WIND LOAD 0.000 -12.553 4.553 0.000 0.000 0.000
Max FZ 13 2:WIND LOAD 0.000 0.000 10.964 1.467 0.000 0.000
Min FZ 2 2:WIND LOAD 0.000 0.000 -7.146 -0.092 0.000 0.000
Max MX 3 2:WIND LOAD 0.000 0.000 1.530 12.693 0.000 0.000
Min MX 2 3:COMBINATION LOAD
0.000
CASE 3 0.000 -7.089 -0.093 0.000 0.000
Max MY 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000
Min MY 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000
Max MZ 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000
Min MZ 1 1:DEAD LOAD 0.000 0.000 0.033 0.003 0.000 0.000

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 TUB80805.0 TUB80805.0 0.040 1.000 0.040 Eq. H3-1 2 14.700 137.000 137.000 217.000
2 TUB80805.0 TUB80805.0 0.056 1.000 0.056 Eq. H1-1b 2 14.700 137.000 137.000 217.000
3 TUB80805.0 TUB80805.0 0.595 1.000 0.595 Eq. H1-1b 2 14.700 137.000 137.000 217.000
4 TUB80805.0 TUB80805.0 0.320 1.000 0.320 Eq. H1-1b 3 14.700 137.000 137.000 217.000
5 TUB80805.0 TUB80805.0 0.166 1.000 0.166 Eq. H1-1b 3 14.700 137.000 137.000 217.000
11 TUB80805.0 TUB80805.0 0.052 1.000 0.052 Eq. H3-1 2 14.700 137.000 137.000 217.000
16 TUB80805.0 TUB80805.0 0.872 1.000 0.872 Eq. H3-6 2 14.700 137.000 137.000 217.000
18 TUB80805.0 TUB80805.0 0.197 1.000 0.197 Eq. H3-1 2 14.700 137.000 137.000 217.000
19 TUB80805.0 TUB80805.0 0.210 1.000 0.210 Eq. H3-1 2 14.700 137.000 137.000 217.000
20 TUB80805.0 TUB80805.0 0.265 1.000 0.265 Eq. H1-1b 2 14.700 137.000 137.000 217.000
21 TUB80805.0 TUB80805.0 0.232 1.000 0.232 Eq. H1-1b 2 14.700 137.000 137.000 217.000
22 TUB80805.0 TUB80805.0 0.150 1.000 0.150 Eq. H1-1b 3 14.700 137.000 137.000 217.000
23 TUB80805.0 TUB80805.0 0.595 1.000 0.595 Eq. H1-1b 2 14.700 137.000 137.000 217.000
24 TUB80805.0 TUB80805.0 0.422 1.000 0.422 Eq. H1-1b 2 14.700 137.000 137.000 217.000
25 TUB80805.0 TUB80805.0 0.269 1.000 0.269 Eq. H3-6 2 14.700 137.000 137.000 217.000

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 17 of 19
 Job No Sheet No Rev
18
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Utilization Ratio Cont...

Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
26 TUB80805.0 TUB80805.0 0.288 1.000 0.288 Eq. H1-1b 2 14.700 137.000 137.000 217.000
27 TUB80805.0 TUB80805.0 0.299 1.000 0.299 Eq. H1-1b 3 14.700 137.000 137.000 217.000
29 TUB80403.2 TUB80403.2 0.103 1.000 0.103 Eq. H3-1 2 7.160 57.200 18.900 46.200
30 TUB80403.2 TUB80403.2 0.151 1.000 0.151 Eq. H3-1 2 7.160 57.200 18.900 46.200
31 TUB80403.2 TUB80403.2 0.146 1.000 0.146 Eq. H3-1 2 7.160 57.200 18.900 46.200
32 TUB80403.2 TUB80403.2 0.227 1.000 0.227 Eq. H1-1b 3 7.160 57.200 18.900 46.200
33 TUB80403.2 TUB80403.2 0.164 1.000 0.164 Eq. H1-1b 3 7.160 57.200 18.900 46.200
34 TUB80403.2 TUB80403.2 0.197 1.000 0.197 Eq. H1-1b 3 7.160 57.200 18.900 46.200
35 TUB80403.2 TUB80403.2 0.137 1.000 0.137 Eq. H1-1b 2 7.160 57.200 18.900 46.200
36 TUB80403.2 TUB80403.2 0.189 1.000 0.189 Eq. H3-1 3 7.160 57.200 18.900 46.200
37 TUB80403.2 TUB80403.2 0.301 1.000 0.301 Eq. H1-1b 2 7.160 57.200 18.900 46.200
38 TUB80403.2 TUB80403.2 0.223 1.000 0.223 Eq. H1-1b 3 7.160 57.200 18.900 46.200
39 TUB80403.2 TUB80403.2 0.200 1.000 0.200 Eq. H1-1b 3 7.160 57.200 18.900 46.200
40 TUB80403.2 TUB80403.2 0.286 1.000 0.286 Eq. H3-1 2 7.160 57.200 18.900 46.200
41 TUB80403.2 TUB80403.2 0.364 1.000 0.364 Eq. H1-1b 2 7.160 57.200 18.900 46.200
42 TUB80403.2 TUB80403.2 0.282 1.000 0.282 Eq. H1-1b 3 7.160 57.200 18.900 46.200
43 TUB80403.2 TUB80403.2 0.319 1.000 0.319 Eq. H1-1b 3 7.160 57.200 18.900 46.200
44 TUB80403.2 TUB80403.2 0.158 1.000 0.158 Eq. H3-1 2 7.160 57.200 18.900 46.200
45 TUB80805.0 TUB80805.0 0.129 1.000 0.129 Eq. H3-1 2 14.700 137.000 137.000 217.000
46 TUB80805.0 TUB80805.0 0.046 1.000 0.046 Eq. H1-1b 3 14.700 137.000 137.000 217.000
47 TUB80805.0 TUB80805.0 0.048 1.000 0.048 Eq. H1-1b 3 14.700 137.000 137.000 217.000
48 TUB80403.2 TUB80403.2 0.183 1.000 0.183 Eq. H1-1b 2 7.160 57.200 18.900 46.200
49 TUB80403.2 TUB80403.2 0.120 1.000 0.120 Eq. H1-1b 2 7.160 57.200 18.900 46.200
50 TUB80403.2 TUB80403.2 0.387 1.000 0.387 Eq. H1-1b 2 7.160 57.200 18.900 46.200
51 TUB80403.2 TUB80403.2 0.268 1.000 0.268 Eq. H1-1b 2 7.160 57.200 18.900 46.200
52 TUB80403.2 TUB80403.2 0.211 1.000 0.211 Eq. H1-1b 3 7.160 57.200 18.900 46.200
53 TUB80403.2 TUB80403.2 0.245 1.000 0.245 Eq. H1-1b 2 7.160 57.200 18.900 46.200
54 TUB80403.2 TUB80403.2 0.194 1.000 0.194 Eq. H1-1b 2 7.160 57.200 18.900 46.200
55 TUB80403.2 TUB80403.2 0.174 1.000 0.174 Eq. H1-1b 2 7.160 57.200 18.900 46.200
56 TUB80403.2 TUB80403.2 0.089 1.000 0.089 Eq. H3-1 3 7.160 57.200 18.900 46.200
57 TUB80403.2 TUB80403.2 0.310 1.000 0.310 Eq. H1-1b 3 7.160 57.200 18.900 46.200
58 TUB80403.2 TUB80403.2 0.146 1.000 0.146 Eq. H3-1 2 7.160 57.200 18.900 46.200
59 TUB80403.2 TUB80403.2 0.136 1.000 0.136 Eq. H1-1b 3 7.160 57.200 18.900 46.200
60 TUB80403.2 TUB80403.2 0.073 1.000 0.073 Eq. H3-1 3 7.160 57.200 18.900 46.200
61 TUB80403.2 TUB80403.2 0.156 1.000 0.156 Eq. H1-1b 3 7.160 57.200 18.900 46.200
62 TUB80403.2 TUB80403.2 0.001 1.000 0.001 Eq. H1-1b 1 7.160 57.200 18.900 46.200
63 TUB80403.2 TUB80403.2 0.002 1.000 0.002 Eq. H1-1b 1 7.160 57.200 18.900 46.200
64 TUB80403.2 TUB80403.2 0.001 1.000 0.001 Eq. H1-1b 1 7.160 57.200 18.900 46.200
65 TUB80403.2 TUB80403.2 0.002 1.000 0.002 Eq. H1-1b 1 7.160 57.200 18.900 46.200
66 TUB80403.2 TUB80403.2 0.273 1.000 0.273 Eq. H1-1b 2 7.160 57.200 18.900 46.200
67 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
68 TUB80403.2 TUB80403.2 0.277 1.000 0.277 Eq. H1-1b 3 7.160 57.200 18.900 46.200
69 TUB80403.2 TUB80403.2 0.370 1.000 0.370 Eq. H1-1b 3 7.160 57.200 18.900 46.200
70 TUB80403.2 TUB80403.2 0.422 1.000 0.422 Eq. H1-1b 3 7.160 57.200 18.900 46.200
71 TUB80403.2 TUB80403.2 0.571 1.000 0.571 Eq. H1-1b 3 7.160 57.200 18.900 46.200

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 18 of 19
 Job No Sheet No Rev
19
Part
Software licensed to
Job Title Ref

By Date17-Feb-22 Chd

Client File WM Sliding Gate.std Date/Time 03-Sep-2022 17:40

Utilization Ratio Cont...

Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
72 TUB80403.2 TUB80403.2 0.226 1.000 0.226 Eq. H1-1b 3 7.160 57.200 18.900 46.200
73 TUB80403.2 TUB80403.2 0.001 1.000 0.001 Eq. H1-1b 1 7.160 57.200 18.900 46.200
74 TUB80403.2 TUB80403.2 0.002 1.000 0.002 Eq. H1-1b 1 7.160 57.200 18.900 46.200
75 TUB80403.2 TUB80403.2 0.118 1.000 0.118 Eq. H1-1b 2 7.160 57.200 18.900 46.200
76 TUB80805.0 TUB80805.0 0.218 1.000 0.218 Eq. H1-1b 3 14.700 137.000 137.000 217.000
77 TUB80805.0 TUB80805.0 0.298 1.000 0.298 Eq. H1-1b 3 14.700 137.000 137.000 217.000
78 TUB80403.2 TUB80403.2 0.221 1.000 0.221 Eq. H1-1b 3 7.160 57.200 18.900 46.200
79 TUB80403.2 TUB80403.2 0.059 1.000 0.059 Eq. H1-1b 2 7.160 57.200 18.900 46.200
80 TUB80403.2 TUB80403.2 0.128 1.000 0.128 Eq. H1-1b 3 7.160 57.200 18.900 46.200
81 TUB80403.2 TUB80403.2 0.286 1.000 0.286 Eq. H1-1b 3 7.160 57.200 18.900 46.200
82 TUB80403.2 TUB80403.2 0.001 1.000 0.001 Eq. H1-1b 1 7.160 57.200 18.900 46.200
83 TUB80403.2 TUB80403.2 0.002 1.000 0.002 Eq. H1-1b 1 7.160 57.200 18.900 46.200
84 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
85 TUB80805.0 TUB80805.0 0.441 1.000 0.441 Eq. H3-6 3 14.700 137.000 137.000 217.000
86 TUB80805.0 TUB80805.0 0.263 1.000 0.263 Eq. H1-1b 3 14.700 137.000 137.000 217.000
87 TUB80403.2 TUB80403.2 0.170 1.000 0.170 Eq. H1-1b 2 7.160 57.200 18.900 46.200
88 TUB80403.2 TUB80403.2 0.050 1.000 0.050 Eq. H1-1b 1 7.160 57.200 18.900 46.200
89 TUB80403.2 TUB80403.2 0.097 1.000 0.097 Eq. H1-1b 3 7.160 57.200 18.900 46.200
90 TUB80403.2 TUB80403.2 0.401 1.000 0.401 Eq. H1-1b 3 7.160 57.200 18.900 46.200
91 TUB80403.2 TUB80403.2 0.001 1.000 0.001 Eq. H1-1b 1 7.160 57.200 18.900 46.200
92 TUB80403.2 TUB80403.2 0.002 1.000 0.002 Eq. H1-1b 1 7.160 57.200 18.900 46.200
93 TUB80403.2 TUB80403.2 0.003 1.000 0.003 Eq. H1-1b 3 7.160 57.200 18.900 46.200
94 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
95 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
96 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
97 TUB80403.2 TUB80403.2 0.000 1.000 0.000 Eq. Sec. D2 1 7.160 57.200 18.900 46.200
98 TUB80403.2 TUB80403.2 0.051 1.000 0.051 Eq. H1-1b 3 7.160 57.200 18.900 46.200

Failed Members
There is no data of this type.

Print Time/Date: 03/09/2022 17:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 19 of 19
 SLIDING GATE POST
(Finite Element Analysis)

ANALYSIS OF GATE POST

METHODOLOGY

In order to support the Sliding Gate Post, the geometry is proposed as indicated in the drawing.
The Gate post is modelled in STAAD.Pro and structural analysis has been made. The loads are
applied on the post in –Z direction, loads are derived from the reaction forces from gate frame
design calculation.
This calculation presents the design of the Sliding Gate Post.

Analysis Tool: STAAD Pro. V8i

Assumptions:

1. Gatepost is fixed at the bottom.

Stiffener Material Properties:

Minimum Specified Yield Strength = 310 MPa

References
ASCE 7-10 Minimum Design loads for Buildings and other
structures
International Building Code (IBC) 2018
 Job No Sheet No Rev
1
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

Job Information
Engineer Checked Approved

Name:
Date: 15-Mar-22

Structure Type SPACE FRAME

Number of Nodes 5 Highest Node 6

Number of Elements 4 Highest Beam 5

Number of Basic Load Cases 2

Number of Combination Load Cases 1

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DEAD LOAD

Primary 2 LIVE LOAD
Combination 3 COMBINATION LOAD CASE 3

3D Rendered View

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 6
 Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

Nodes
Node X Y Z
(m) (m) (m)
1 0.000 0.000 0.000
2 0.000 3.447 0.000
4 0.000 3.447 0.400
5 0.000 3.050 0.400
6 0.000 3.050 0.000

Beams
Beam Node A Node B Length Property 
(m) (degrees)
1 1 6 3.050 2 0
2 2 4 0.400 1 90
4 5 4 0.397 1 0
5 6 2 0.397 2 0

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 200X100X4RHS 23.200 416.000 1.22E+3 969.978 STEEL
2 200X5SHS 38.700 2.45E+3 2.45E+3 3.71E+3 STEEL

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 Fixed Fixed Fixed Fixed Fixed Fixed

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 6
 Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

2
4
6
5

Y
X
Z Load 2
1

Whole Structure

2
5
4

Y
X Load 2
Z

Whole Structure

Primary Load Cases

Number Name Type

1 DEAD LOAD Dead

2 LIVE LOAD Live

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 6
 Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 COMBINATION LOAD CASE 3 1 DEAD LOAD 1.00

2 LIVE LOAD 1.00

10.900 kN

Y
X
Z Load 2

Whole Structure

1 DEAD LOAD : Selfweight

Direction Factor Assigned Geometry

Y -1.000 ALL

2 LIVE LOAD : Node Loads

Node FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
6 - - 10.900 - - -

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 6
 Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

Node Displacement Summary

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min X 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max Y 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min Y 5 3:COMBINATION LOAD
0.000
CASE 3 -4.064 20.813 21.206 0.010 0.000 0.000
Max Z 2 3:COMBINATION LOAD
0.000
CASE 3 -0.003 24.844 24.844 0.010 0.000 0.000
Min Z 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max rX 4 3:COMBINATION LOAD
0.000
CASE 3 -4.064 24.844 25.174 0.010 0.000 0.000
Min rX 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max rY 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min rY 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max rZ 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min rZ 1 1:DEAD LOAD 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max Rst 4 3:COMBINATION LOAD
0.000
CASE 3 -4.064 24.844 25.174 0.010 0.000 0.000

Beam Combined Axial and Bending Stresses Summary

Max Comp Max Tens
Beam L/C Length Stress d Corner Stress d Corner
(m) (MPa) (m) (MPa) (m)
1 1:DEAD LOAD 3.050 0.476 0.000 1 -0.107 3.050 1
2:LIVE LOAD 3.050 135.971 0.000 2 -135.971 0.000 1
3:COMBINATION LOAD
3.050
CASE 136.447
3 0.000 2 -135.844 0.000 1
2 1:DEAD LOAD 0.400 0.512 0.000 2 -0.512 0.000 1
2:LIVE LOAD 0.400 0.000 0.000 2 -0.000 0.000 1
3:COMBINATION LOAD
0.400
CASE 3 0.512 0.000 2 -0.512 0.000 1
4 1:DEAD LOAD 0.397 0.000 0.000 1 -0.030 0.397 1
2:LIVE LOAD 0.397 0.000 0.000 1 -0.000 0.000 2
3:COMBINATION LOAD
0.397
CASE 3 0.000 0.000 1 -0.030 0.397 1
5 1:DEAD LOAD 0.397 0.241 0.000 2 -0.137 0.397 1
2:LIVE LOAD 0.397 0.000 0.000 2 -0.000 0.000 1
3:COMBINATION LOAD
0.397
CASE 3 0.241 0.000 2 -0.137 0.397 1

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 6
 Job No Sheet No Rev
6
Part
Software licensed to
Job Title Ref

By Date15-Mar-22 Chd

Client File Sliding Gate Post.std Date/Time 03-Sep-2022 17:55

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min FX 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Max FY 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min FY 1 2:LIVE LOAD 0.000 0.000 -10.900 -33.245 0.000 0.000
Max FZ 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min FZ 1 2:LIVE LOAD 0.000 0.000 -10.900 -33.245 0.000 0.000
Max MX 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min MX 1 3:COMBINATION LOAD
0.000
CASE 3 1.167 -10.900 -33.288 0.000 0.000
Max MY 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min MY 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Max MZ 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000
Min MZ 1 1:DEAD LOAD 0.000 1.167 -0.000 -0.043 0.000 0.000

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 200X5SHS 200X5SHS 0.512 1.000 0.512 Eq. H1-1b 3 38.700 2.45E+3 2.45E+3 3.76E+3
2 200X100X4RHS
200X100X4RHS0.002 1.000 0.002 Eq. H1-1b 1 23.200 1.22E+3 416.000 983.000
4 200X100X4RHS
200X100X4RHS0.000 1.000 0.000 Eq. Sec. D2 1 23.200 1.22E+3 416.000 983.000
5 200X5SHS 200X5SHS 0.001 1.000 0.001 Eq. H1-1b 1 38.700 2.45E+3 2.45E+3 3.76E+3

Failed Members
There is no data of this type.

Print Time/Date: 03/09/2022 17:58 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 6
Conclusion
The gate is stable and safe under the conditions of dead and wind load. Following are the stress and
deflection checks.

No Parameter Allowable Actual Clause

01 Combined bending and 310 265.8 Ref. - IBC 1604.2
axial stress (Mpa)
02 Deflection (mm) 2.5% of 10000 = 250 199.7 Ref. – AASHTO 10.4.2.1

Connection design between steel vertical and horizontal members

Axial load on the weakest joint Fx = 3.25 KN

Shearing load on the weakest joint Fy = 10.4 KN

Failure in shear
Primary Pipe size = 80 x 80 SQ
Length of weld = perimeter of pipe = 320 mm
Weld bead thickness = 4 mm
Area of weld = 1280 mm2
Stress induced = 10400/1280 = 8.125 MPa…..……………….(1)
Material yield strength = 310 MPa
Strength in shear = 0.55 x 310 = 170.5 MPa………….….…..(2)
Since Eqn(1) < Eqn(2), Connection is safe.

Failure in tension
Primary Pipe size = 80 x 80 SQ
Length of weld = perimeter of pipe = 320 mm
Weld bead thickness = 4 mm
Area of weld = 1280 mm2
Stress induced = 3250/1280 = 2.53 MPa…………….……..….(3)
Material yield strength = 310 MPa
Strength in shear = 0.55 x 310 = 170.5 MPa……………..…..(4)
Since Eqn(3) < Eqn(4), Connection is safe

**********************************************************************************
Reaction Force in –Z direction from STAAD analysis = 7.7 KN

Height of the gate = 2.9 m

Moment on the foundation Mx = 7.7 x 2.9 x 0.5 = 11.16 KN-m

FOUNDATION DESIGN

Allowable bearing pressure of soil (Pb) 100 KN/m2

=
Concrete unit weight = 24 KN/m3
System DL (Fy) = 330 kg
= 3.30 KN
Assuming Width of Footing = 0.8 m
Assuming Length of Footing = 1.6 m
Depth = 1 m

1 Check assumed footing dimensions against applied load

Gross Dead Load on the soil (W) = System DL + Concrete weight
Pedestal Weight = 30.72 KN
Concrete weight above pedestal = 0.00
Gross Dead Load (W) = 34.02 KN
Area of Footing (W/Pb) = 0.3402 m2
Side of the Foundation, b (Square) = 0.583 m
< 0.8

2 Depth of the foundation by Rankine’s formula

Minimum depth of foundation =p/w (1-sin Φ /1+sin Φ) 2
Where
p = gross bearing capacity/load on soil = 26.58 KN/m2
w = Density of soil = 15 KN/m3 (Dry sand)
Φ = Angle of repose = 30 ° (Dry sand)
Depth (D) = 37.55/15(1-sin30/1 + sin30)2
Depth (D) = 0.197 m
< 1
Foundation size - 800 x 1600 x 1000

3 Stability check against overturning-

Over Turning moment Mx = 11.16 KN-m (Reaction Moment)
Resisting moment = Moment due to vertical load + Moment due to Lateral Soil load
Total Vertical load = Fence dead load + Pedestal load + sill beam weight
Fence dead load ≈ 3.30 KN
Pedestal load = 30.72 KN
Soil Weight above pedestal = 0.00 KN
 Total Vertical load = 34.02 KN …...........(01)
Moment at extreme edge on pedestal = 13.61 KN-m
Considering lateral Soil Load
Passive soil load Fp = 1/2 x Kp x w x D2 x B
Active soil load Fa = 1/2 x Ka x w x D2 x B
Where
Kp = Coefficient of passive earth pressure
Ka = Coefficient of active earth pressure
w = Unit weight of soil (15 KN/M3)
D = Depth of foundation
B = Side of square foundation
Φ = Angle of Repose (30 deg)
Kp = (1+sin Φ /1-sin Φ) = 3
Ka = (1-sin Φ /1+sin Φ) = 0.33
Passive Soil Load, Fp = 18.00 KN
Active soil load, Fa = 3.96 KN
Resisting moment due to passive soil Pr = Fp x D/3 = 6.00 KN-m
Overturning moment due to active soil Pr = Fa x D/3 = 1.32 KN-m
Total Resisting Moment = 19.61 KN-m
Total Overturning Moment = 12.48 KN-m
Factor of Safety = 1.57
> 1.5 (Ref. IBC 1807.2.3)
Foundation is Safe

4 Stability check against sliding-

Sliding force in -Z direction = 7.70 KN
Total vertical load on soil = 34.02 KN (From Eqn 01)
Coefficient of friction for Soil and Concrete = 0.35
Resisting force for sliding = 11.91 KN
Lateral soil force = 14.04 KN
Total Resisting force = 25.95 KN
Factor of Safety = 3.37
> 1.5 (Ref. IBC 1807.2.3)
Foundation is Safe