Scribd
Upload
220 views5 pages

Relief Valve (Torque Converter)

This document provides instructions for testing and adjusting the relief valve (torque converter outlet) pressure on a D7G track-type tractor powered by a 3306 engine. The procedure involves installing various tools at the pressure tap on the torque converter outlet relief valve to check the oil pressure. If the pressure is incorrect, spacers can be added or removed from the valve to adjust the setting. The proper pressure is 290 ± 14 kPa (42 ± 2 psi).

Uploaded by

Steven Y.M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
220 views5 pages

Relief Valve (Torque Converter)

This document provides instructions for testing and adjusting the relief valve (torque converter outlet) pressure on a D7G track-type tractor powered by a 3306 engine. The procedure involves installing various tools at the pressure tap on the torque converter outlet relief valve to check the oil pressure. If the pressure is incorrect, spacers can be added or removed from the valve to adjust the setting. The proper pressure is 290 ± 14 kPa (42 ± 2 psi).

Uploaded by

Steven Y.M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

D7G TRACK-TYPE TRACTOR 7MB00001-UP (MACHINE) POWERED BY 3306 EN...

Page 1 of 5

Shutdown SIS

Previous Screen

! " #$
%& ' (( ) % $
%

!"#$" %& ' %&(&&( %% ) *(&&( %%

*+,*-(

Relief Valve (Torque Converter Outlet) Pressure - Test


and Adjust
SMCS - 3133-036

Personal injury can result from hydraulic oil pressure and


hot oil.

Hydraulic oil pressure can remain in the hydraulic system


after the engine has been stopped. Serious injury can be
caused if this pressure is not released before any service is
done on the hydraulic system.

Make sure all of the attachments have been lowered, oil is


cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is
cool enough to touch with your bare hand.

Introduction
The relief valve (torque converter outlet) maintains a minimum oil pressure in the torque
converter.

Follow this procedure in order to adjust the pressure setting for the relief valve (torque

https://198.101.110.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/si... 11/19/2008
D7G TRACK-TYPE TRACTOR 7MB00001-UP (MACHINE) POWERED BY 3306 EN... Page 2 of 5

converter outlet).

Required Tools

Illustration 1 g01089423
Tooling (A)

Illustration 2 g01282274
Tooling (B)

https://198.101.110.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/si... 11/19/2008
D7G TRACK-TYPE TRACTOR 7MB00001-UP (MACHINE) POWERED BY 3306 EN... Page 3 of 5

Table 1

Required Tools
Part
Tooling Item Description Qty
Number
Pressure Gauge
A1 8T-0854 1
0 to 1000 kPa (0 to 144 psi)
A2 6V-3989 Fitting 1
A
A3 6V-4143 Coupler 2
Hose As
A4 177-7861 1
0 to 6000 kPa (0 to 870 psi)
B B 8T-3613 Fitting As 1

Test and Adjust


1. Move the machine to a smooth horizontal location.

2. Lower all of the implements. Engage the parking brake. Turn the engine OFF.

https://198.101.110.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/si... 11/19/2008
D7G TRACK-TYPE TRACTOR 7MB00001-UP (MACHINE) POWERED BY 3306 EN... Page 4 of 5

Illustration 3 g01297550
The pressure tap for the torque converter outlet relief valve is located on the torque
converter outlet relief valve. The torque converter outlet relief valve is located on the rear
face of the torque converter under the floorplate of the operator station.

(D) Pressure tap for the torque converter outlet

3. Remove plug (D) from the torque converter outlet relief valve. Install tooling (B).
Attach tooling (A) to tooling (B) .

4. Start the engine. Warm the power train oil to operating temperature.

5. Disengage the parking brake. Engage the service brake. Move the transmission
selection lever to the THIRD SPEED FORWARD position. Make sure that the
steering control levers are in the NEUTRAL position. Operate the engine at HIGH
IDLE.

6. Check the pressure at tooling (A). The pressure at tooling (A) should be 290 ± 14
kPa (42 ± 2 psi).

https://198.101.110.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/si... 11/19/2008
D7G TRACK-TYPE TRACTOR 7MB00001-UP (MACHINE) POWERED BY 3306 EN... Page 5 of 5

Illustration 4 g01282277

7. If the pressure is incorrect then install spacers (2) or remove spacers in order to
change the pressure setting of the torque converter outlet relief valve (1) .

Note: One 5S-7001 Spacer changes the pressure setting by 40 kPa (5.8 psi). One
4M-1751 Spacer changes the pressure setting by 19 kPa (2.8 psi). Adding spacers
increases the pressure and removing spacers lowers the pressure.

ReferenceRefer to the procedures in Disassembly and Assembly, "Torque


Converter Outlet Relief Valve" in the Service Manual for your machine.

8. When the pressure setting is correct, tighten bolts (3) to a torque of 48 ± 7 N·m (35
± 5 lb ft). Remove the test equipment. Install plug (D). Tighten the plug to a torque
of 16 ± 2 N·m (142 ± 18 lb in). Prepare the machine for service.

./ 0 ,,( * 1 . $ 2 ' %4 , *+ +! : * 1
03 3 4 2
4 % 5 67 8$89 3 32

https://198.101.110.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/si... 11/19/2008

You might also like