Scribd
Upload
112 views

Router Configuration

Uploaded by

julio de leon
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
112 views

Router Configuration

Uploaded by

julio de leon
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4,


RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thurs 5-Jan-12 15:41 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040

This product contains cryptographic features and is subject to United


States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to


[email protected].

Cisco CISCO1941/K9 (revision 1.0) with 491520K/32768K bytes of memory.


Processor board ID FTX152400KS
2 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#no s
Router(config-if)#no sh
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up
Router(config-if)#exit
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0.10
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.10, changed


state to up

Router(config-subif)#
Router(config-subif)#
Router(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip a
Router(config-subif)#ip ad
Router(config-subif)#ip address
% Incomplete command.
Router(config-subif)#ip address 29.01.40.1 255.255.255.0
Router(config-subif)#exit
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0.20
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.20, changed


state to up

Router(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip a
Router(config-subif)#ip ad
Router(config-subif)#ip address 172.21.13.1 255.255.255.0
Router(config-subif)#exit
Router(config)#ip dh
Router(config)#ip dhcp p
Router(config)#ip dhcp pool v
Router(config)#ip dhcp pool vl
Router(config)#ip dhcp pool vla
Router(config)#ip dhcp pool vlan 10
^
% Invalid input detected at '^' marker.

Router(config)#
Router(config)#ip
Router(config)#ip dh
Router(config)#ip dhcp p
Router(config)#ip dhcp pool vlan10
Router(dhcp-config)#net
Router(dhcp-config)#network 29.01.40.0 255.255.255.0
Router(dhcp-config)#dns
Router(dhcp-config)#dns-server 29.01.40.1
Router(dhcp-config)#exit
Router(config)#ip
Router(config)#ip d
Router(config)#ip dh
Router(config)#ip dhcp e
Router(config)#ip dhcp excluded-address 29.01.40.1 29.01.40.10
Router(config)#ip dc
Router(config)#ip dch
Router(config)#ip dchp
Router(config)#dhp
Router(config)#ip dh
Router(config)#ip dhcp p
Router(config)#ip dhcp pool vl
Router(config)#ip dhcp pool vla
Router(config)#ip dhcp pool vlan20
Router(dhcp-config)#net
Router(dhcp-config)#network 172.21.13.1
% Incomplete command.
Router(dhcp-config)#
Router(dhcp-config)#net
Router(dhcp-config)#network 172.21.13.0 255.255.255.0
Router(dhcp-config)#nd
Router(dhcp-config)#dn
Router(dhcp-config)#dns-server 172.21.13.1
Router(dhcp-config)#exit
Router(config)#ip dh
Router(config)#ip dhcp e
Router(config)#ip dhcp excluded-address 172.21.13.1 172.21.13.10
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#co
Router#con
Router#configure t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip dh
Router(config)#ip dhcp p
Router(config)#ip dhcp pool vl
Router(config)#ip dhcp pool vl
Router(config)#ip dhcp pool vl
Router(config)#ip dhcp pool vlan10
Router(dhcp-config)#d
Router(dhcp-config)#de
Router(dhcp-config)#default-router 29.01
^
% Invalid input detected at '^' marker.

Router(dhcp-config)#default-router 29.01.40.1
Router(dhcp-config)#exit
Router(config)#enable
% Incomplete command.
Router(config)#con
Router(config)#configute t
^
% Invalid input detected at '^' marker.

Router(config)#
Router(config)#ip d
Router(config)#ip dh
Router(config)#ip dhcp p
Router(config)#ip dhcp pool vlan20
Router(dhcp-config)#def
Router(dhcp-config)#default-router 172.21.13.1
Router(dhcp-config)#exit
Router(config)#co
Router(config)#copy
Router(config)#copy r
Router(config)#copy ru
Router(config)#copy runn
Router(config)#copy running-config startup-config
^
% Invalid input detected at '^' marker.

Router(config)#
Router(config)#copy running-config startup-config
^
% Invalid input detected at '^' marker.

Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#copy running-config startup-config


Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router#
Router#
Router#

You might also like