Product Data Sheet

Atlac 382 Powder

Product description Properties of the resin upon delivery (typical

Atlac 382 Powder is a pulverised solid propoxylated values)
bisphenol A fumarate polyester. The powder can Property Value Unit TM
easily be dissolved in a reactive monomer, such as Stability, no init., dark, 25°C 12 Month -
styrene, resulting in an unsaturated polyester resin.
A solution of 50 % (w/w) Atlac 382 Powder in styrene Dissolving Atlac 382 Powder
is commercially available as Atlac 382 (see paragraph Atlac 382 resin in styrene can be made by dissolving
dissolving Atlac 382 Powder in styrene) 50 % (w/w) Atlac 382 POWDER in 50 % (w/w) styrene.
The most suitable mixing procedure will depend on
Performance the type of mixer that is available. When using a
Atlac 382 resins are suitable for high temperature
Cowless type mixer, first put all styrene into the
water, acid and salt solutions and medium container. Start agitation and add Atlac 382 powder
temperature alkali solutions. as fast as the agitation will remove the solid resin
Major applications from the liquid surface. When a propeller-type mixer
Atlac 382 resins can be used in all fabrication is used, add one half of the styrene into the mixing
methods, but are especially adapted to meet the container and start agitation. Charge Atlac 382
requirements of filament winding, centrifugal Powder slowly with continuous vortex agitation.
casting, hand lay-up and spray-up applications. When all of the Atlac 382 Powder has been added
These resins may also be used to formulate and a homogenous mixture is obtained the remaining
glassflake coatings and mortars. quantity of styrene can be added under continuous
agitation.
Approvals
Cured non-reinforced Atlac 382 resins conform to It is advised to add a small quantity of inhibitor to
type 1310 according to DIN 16946/2 and are the styrene before adding the Atlac 382 Powder. The
classified group 5 according to DIN 18820/1 and inhibitor advised is p-tert-butylcatechol that is
group 6 according to EN12131/2. available in a 10% solution. (Inhibitor NLC-10 – AKZO-
Nobel)
Product specifications upon delivery) Dissolving Atlac 382 POWDER into styrene will be
Property Value Unit TM accelerated when increasing the temperature
Viscosity, 23°C 560 - 660 mPa.s 2013 slightly up to 50°C.
Color, Gardner 0-6 - 2017
Appearance Dusty - 2265 In order to adjust reactivity of the resin mixture both
pale dimethylaniline and cobalt have to be used. In the
yellow Atlac Anti Corrosion Industry brochure starting
Acid value, as such 11 - 14
mg 2401 formulations can be found for different reactivity
KOH/g characteristics.
Gel time from 25 to 35°C 5 - 12 Minutes 2625
Cure time from 25°C to peak 22 - 30 Minutes 2625
See brochure Atlac Anti Corrosion Industry for
Date of issue: September 13 Version: 001894/7.0

Peak temperature 140 - 170 °C 2625

further details.
Granulometria > 425 micron 1 % 5177
Remarks
TM2013: Diluted at 50%
TM2017: 50% in styrene
TM2625: 0,5g NL51P + 1,0g Pergaquick A2 X + 1,5g But M50

The user is held to check the quality, safety and other properties of the product referred to herein. The information and recommendations in
this document are to the best of our knowledge, reliable. However, no rights whatsoever can be derived from this document or the
information contained therein by any party, other than those expressly accepted by a selling entity of the Royal DSM group of companies
(“DSM Selling Entity”) in a binding sale and purchase agreement for product referred to herein. For the avoidance of doubt THE ROYAL DSM
GROUP OF COMPANIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
PURPOSE. Unless explicitly agreed to otherwise in writing by the DSM Selling Entity, all offers, quotations, sales and deliveries of DSM products
are subject to the General Conditions of Sale of such DSM Selling Entity.

This document has been issued by DSM Composite Resins on behalf of the DSM Selling Entity. For more information: www.compositeresins.com

Page 1 of 2
 Product Data Sheet

Atlac 382 Powder

Storage guidelines
The resin should be stored indoors in the original unopened and undamaged packaging, in a dry place at
temperatures between 5°C and 30 °C. The shelf life of styrene containing unsaturated polyester will be
significantly reduced when exposed to light. Store in dark and in 100% light tight containers only.

Material Safety
A Material Safety Data Sheet of this product is available on request.

Test methods
Test methods referred to in the tables are available on request.
Date of issue: September 13 Version: 001894/7.0

The user is held to check the quality, safety and other properties of the product referred to herein. The information and recommendations in
this document are to the best of our knowledge, reliable. However, no rights whatsoever can be derived from this document or the
information contained therein by any party, other than those expressly accepted by a selling entity of the Royal DSM group of companies
(“DSM Selling Entity”) in a binding sale and purchase agreement for product referred to herein. For the avoidance of doubt THE ROYAL DSM
GROUP OF COMPANIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
PURPOSE. Unless explicitly agreed to otherwise in writing by the DSM Selling Entity, all offers, quotations, sales and deliveries of DSM products
are subject to the General Conditions of Sale of such DSM Selling Entity.

This document has been issued by DSM Composite Resins on behalf of the DSM Selling Entity. For more information: www.compositeresins.com

Page 2 of 2