Free Energy from Centrifugal Force
In this document, we discuss two methods of obtaining over-unity using centrifugal force as the accelerator.
1. Implosion Motors
2. Spinning weight or pendulum
Centrifugal force can be thought of as pressure on the center shaft. We want to turn the pressure into work, but we do
not want to disturb the rotation of the spinning mass. We must make a compromise. We must “sacrifice” a small portion
of our perfect circular motion to gain acceleration.
Implosion Motors
Moving weights can get expensive in terms of the cost of parts and manufacturing, but they can get very expensive in
terms of mechanical losses. One method of free energy from centrifugal force is to use spinning water as the weight,
and water jets as the method of acceleration. These machines can be built cheaply and do not require a lot of moving
parts. Because the motion of the water creates vacuum pressure, they are called implosion motors. Viktor Schauberger
is famous for implosion technology and called some of his machines a “repulsine”.
The speed of these machines can be regulated by a pressure relief valve, much like on a compressed air tank.
THE IMPLOSION GENERATOR by Viktor Schauberger
http://www.nzdl.org/cgi-bin/library?e=d-00000-00---off-0hdl--00-0----0-10-0---0---0direct-10---4-------0-1l--11-en-50---
20-about---00-0-1-00-0--4----0-0-11-10-0utfZz-8-10&cl=CL1.6&d=HASHad5d9027d93da18e8b476b.7>=1
Home power generator by Schauberger
Schauberger’s designs were overly complicated. The complexity of his designs had a purpose, but the design does not
need to be that complicated to work. All that is needed is a spinning drum full of water with jets on the outside, so that
as the water jets out, it accelerates the drum, and sucks more water into the drum. If the water spins both radially and
axially, it becomes highly diamagnetic and repels the earth. This is a type of anti-gravity. If you would like more
information on implosion motors or anti-gravity technology, contact WITTS ministries
[email protected] or visit their
website http://www.witts.ws
Rotor “veins” for the water jets to push against can be seen around the inside circumference.
https://kigp.ru/en/vortex-engine-of-the-victor-schauberger-how-does-victor-schaubergers-engine-work/
https://www.flickr.com/photos/esaruoho/4934529764/in/photostream/
Useful link on Schauberger:
https://www.gsjournal.net/Science-Journals/Research%20Papers-Engineering%20(Applied)/Download/8687
2. Spinning weight or pendulum
The most common form of this technology is called the two-stage oscillator. This was invented by Veljko Milkovic.
This design uses a pendulum. It harnesses the force of gravity and centrifugal force together. Centrifugal force can be
thought of as pressure on the center pivot. This pressure can be turned into mechanical energy. The trick is to have the
weight not move very much from the center. RHEAD100 on YouTube has stated the weight should not move more than
10% of the radius of the weight. However, I believe that is too much. The amount of movement should be as small as
possible so that the weight does not slow down. 1/8" on a 15" radius would be appropriate.
Pavol Nemeš’ Linear force generator using sliders.
https://www.youtube.com/watch?v=bAsIoUPx0eE
Oscillating motion can be converted to rotational motion using a double-ratcheting or double-sprag mechanism.
Double-sprag mechanism. Sprags, one-way bearings, or ramp-roller clutches are in automatic transmissions.
There are two other ways of harnessing centrifugal force. The next one discussed is limited by gravity so its power
output is limited. A weight moves out from the center axis, and gravity brings it back in.
There is a third method which is more difficult to set up. A weight moves in a circle and pulls a rod almost tangential to
its velocity. This method may not be suitable for a free energy machine because it may slow the weight down
substantially.
https://www.youtube.com/watch?v=Upp-Xr5JAg0
Third method concept illustrated. Here the pivot of the linkage rod is too far from the center pivot. The weight should
not move very much from the center pivot. Ron Brandt built a machine like this after seeing Timothy Thrapp’s gravity
motors. Ron’s weight was about 2” round and 2” long, and the machine was about 9” in diameter. The device required a
spring and proper tuning. It sat on a desk and spun at 200-300RPM. Ron tired to get it to work without the spring but
was unsuccessful.
