DELRIN® 150 Series Natural - Stock Shapes (rods, plates, tubes)
Chemic al Des ignat ion Main feat ures Target Indus t ries
POM-H (Polyacetal (Homopolymer)) good machinability food processing
high stiffness food engineering
Colour
high fatigue strength automotive industry
white
high creep resistance conveyor technology
Dens it y good wear properties construction industry
1.41 g/cm3 very good abrasion resistance mechanical engineering
electronics
fixture construction
gear manufacturing
home appliances
Me ch a n i ca l p ro p e rti e s co n d i ti o n va l u e te s t m e th o d co m m e n t
Modulus of elasticity @ 73 °F 350,000 psi ASTM D 638
(tensile test)
Tensile strength at yield 11,000 psi ASTM D 638
Elongation at break (tensile @ 73 °F 25 % ASTM D 638
test)
Flexural strength @ 73 °F 14,000 psi ASTM D 790
Modulus of elasticity @ 73 °F 470,000 psi ASTM D 790
(flexural test)
Compression strength @ 1% strain 3,600 psi ASTM D 695
Compression strength @ 10% strain 15,500 psi ASTM D 695
Compression modulus 325,000 psi ASTM D 695
Impact strength (Izod) @ 73 °F 1.5 ft-lbs/in -
Rockwell hardness @ 73 °F 94 (120) ASTM D 785
M Scale (R Scale)
Coefficient of friction Dynamic .2 ASTM D 3702
40 psi, 50 fpm
Wear rate 40 psi, 50 fpm 55*10 -10 in³-min/ft-lbs-hr ASTM D 3702
Th e rm a l p ro p e rti e s co n d i ti o n va l u e te s t m e th o d co m m e n t
Melting temperature 347 °F ASTM D 2133 1) (1) Injec tion molded sample
Deflection temperature @ 66 psi 336 °F ASTM D 648
Deflection temperature @264 psi 257 °F ASTM D 648
Service temperature Intermittent 300 °F -
Service temperature Long Term 185 °F -
Thermal expansion (CLTE) 6.8*10 -5 in/in/°F ASTM D 696
Specific heat 0.35 BTU/lb-F° -
El e ctri ca l p ro p e rti e s co n d i ti o n va l u e te s t m e th o d co m m e n t
Volume resistivity > 10 15 Ω*cm ASTM D257
Dielectric strength 500 V/mil ASTM D 149
Dissipation factor @ 60 Hz, 73 °F .005 ASTM D 150
Dielectric constant @ 60 Hz, 73 °F, 50% RH 3.7 ASTM D 150
Oth e r p ro p e rti e s co n d i ti o n va l u e te s t m e th o d co m m e n t
Moisture absorption @ 24 hrs, 73 °F .25 % ASTM D 570 (1) 1.47mm injec tion mold
Moisture absorption @ saturation, 73 °F .90 % ASTM D 570
Flammability (UL94) UL 94 HB - 1)
Resin specification:
ASTM D6778-06 POM0111 superseding ASTM D4181-00 POM111
Shapes specification:
ASTM D6100-11 S-POM0111
This information reflec ts the c urrent state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or
guarantee c hemic al resistanc e, quality of produc ts or their suitability in any legally binding way. Values are not minimum or maximum values, but guidelines that c an be
used for c omparative purposes in material selec tion. They are within the normal range of produc t properties and do not represent guaranteed property values. Testing
under individual applic ation c irc umstanc es is always rec ommended. Data is obtained from extruded shapes material unless otherwise noted. Referenc es to FDA
c omplianc e refer to the resins from whic h the produc ts were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet
values are subjec t to periodic review, the most rec ent update c an be found at www.ensingerplastic s.c om.
Ensinger Inc. Headquarters Phone 800-243-3221 Sales Date: 2020/10/07 Version: A3
365 Meadow lands Boulevard Phone 800-869-4029 Technical
Washington, PA 15301, USA Fax 724-746-9209
[email protected]
