Scribd
Upload
332 views22 pages

Experiment 1:: Non-Inverting, Inverting Amplifiers and Voltage Follower

The document describes three experiments conducted using operational amplifiers: 1) Designing and simulating inverting, non-inverting, and voltage follower amplifiers in LTSpice. DC and AC analyses were performed on the output. 2) Designing summer, subtractor, and averaging circuits in LTSpice to perform arithmetic operations. DC and AC analyses were performed on the outputs. 3) Designing a scaling adder circuit in LTSpice to calculate various weighted sums. DC analyses were performed on the outputs.

Uploaded by

ag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as ODT, PDF, TXT or read online on Scribd
332 views22 pages

Experiment 1:: Non-Inverting, Inverting Amplifiers and Voltage Follower

The document describes three experiments conducted using operational amplifiers: 1) Designing and simulating inverting, non-inverting, and voltage follower amplifiers in LTSpice. DC and AC analyses were performed on the output. 2) Designing summer, subtractor, and averaging circuits in LTSpice to perform arithmetic operations. DC and AC analyses were performed on the outputs. 3) Designing a scaling adder circuit in LTSpice to calculate various weighted sums. DC analyses were performed on the outputs.

Uploaded by

ag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as ODT, PDF, TXT or read online on Scribd
You are on page 1/ 22

DATE: 04.01.

2022 NAME: ANJALI TIWARI


REGISTER NUMBER: 20BEC1177
ECE3013: LINEAR INTEGRATED CIRCUITS

EXPERIMENT 1: NON-INVERTING, INVERTING AMPLIFIERS AND


VOLTAGE FOLLOWER

AIM: To design and study the behaviour of operational amplifier as inverting, non-
inverting and voltage follower circuits.

PROCEDURE:
1. Designing the external resistance of the op-amp.
2. Constructing the circuit of inverting amplifier, non-inverting amplifier and
voltage follower in LT-Spice.
3. Simulating the amplifiers with dc input and ac input.
4. Tabulating the result.

CIRCUIT DIAGRAM:

INVERTING AMPLIFIER
NON-INVERTING AMPLIFIER

VOLTAGE FOLLOWER
LTSPICE CIRCUIT:

i. INVERTING AMPLIFIER WITH DC INPUT

DC OPERATING POINT ANALYSIS:


ii. INVERTING AMPLIFIER WITH AC INPUT

TRANSIENT ANALYSIS RESULT:


iii. NON-INVERTING AMPLIFIER WITH DC INPUT

DC OPERATING POINT ANALYSIS


iv. NON-INVERTING AMPLIFIER WITH AC INPUT

TRANSIENT ANALYSIS RESULTS


v. VOLTAGE FOLLOWER

DC OPERATING POINT ANALYSIS


AC ANALYSIS:

RESULT:
The operational amplifier is used as inverting, non-inverting and voltage follower
and the output dc analysis and waveforms are studied.
DATE: 11.01.2022 NAME: ANJALI TIWARI
REGISTER NUMBER: 20BEC1177
ECE3013: LINEAR INTEGRATED CIRCUITS

EXPERIMENT 2: ARITHMETIC OPERATION WITH OP-AMPS

AIM: To perform the following operations using op-amp


1. Summing
2. Average
3. Subtraction

PROCEDURE:
1. Designing the external resistance of the op-amp.
2. Constructing the circuit of summer, subtractor and averaging circuit
3. Simulating the amplifiers with dc input and ac input.
4. Tabulating the result.

CIRCUIT DIAGRAM:
SUMMING OPERATION
SUBTRACTION OPERATION

AVERAGE OPERATION
1. SUMMING OPERATION
LTSPICE CIRCUIT DIAGRAM:

DC OPERATING POINT ANALYSIS:


VOUT = -(V1+V2+V3)
= -(1+2+3) = -6 V
AC ANALYSIS:
2. SUBTRACTION OPERATION
LTSPICE CIRCUIT DIAGRAM:

VOUT = V2-V1
= 2-1 = 1V
AC ANALYSIS:
3. AVERAGING OPERATION

VOUT = -(V1+V2+V3)/3
= -(1+2+3)/3
= -2 V
DC OPERATING POINT RESULT:
AC ANALYSIS:

RESULT:
The operational amplifier is used to perform addition, subtraction and average
and the output dc analysis and waveforms are studied.
DATE: 03.02.2022 NAME: ANJALI TIWARI
REGISTER NUMBER: 20BEC1177
ECE3013: LINEAR INTEGRATED CIRCUITS

EXPERIMENT 3: SCALING ADDER CIRCUIT

AIM: To design and study the behaviour of operational amplifier as scaling adder
circuit.

PROCEDURE:
1. Designing the external resistance of the op-amp.
2. Constructing the circuit of scaling adder in LT-Spice.
3. Simulating the amplifiers with dc input.
4. Tabulating the result.

LT-SPICE DIAGRAM:
i. V0 = 2*V1 + 3*V2 + 4*V3
DC OPERATING POINT ANALYSIS:

V0 = 2*V1 + 3*V2 + 4*V3 = 2*(5)+3*(10)+4*(20) mV


= 0.12 V
ii. V0 = -(V1 + 2*V2 + 3*V3 )

DC OPERATING POINT ANALYSIS RESULT:

V0 = -(V1 + 2*V2 + 3*V3 )


=-(5+2*10+3*20) mV
= -0.085 V
iii. V0 = V1 - 2*V2 + 4*V3 -6*V4 + 5*V5

DC OPERATING POINT ANALYSIS:


V0 = V1 - 2*V2 + 4*V3 -6*V4 + 5*V5
= (5-2*10+4*20-6*30+5*40) mV
= 0.085 mV

RESULT:
The operational amplifier is used to perform scaling adder operation.

You might also like