ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev.

A 2003

!"#$$$$%&'()*+$",&-./012$/34-5$$$$$$$$$$$$$$$$$$$6"7"#8#777$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

The board is the controller of the entire unit.

It is a standard PC board with already assembled the base peripherals:

serial, parallel, SCSI, LAN, VGA.

The CPU (DSM1) is connected by the PCE to the MBU and with flat cables to the VCB1
and VCB2.
With its internal SCSI connects the magneto optical drive.
The Hard disk drive, where there is the program of the unit, and the CD-ROM drive are
connected to the board by the internal IDE port.
On it arrives also the alphanumeric keyboard and the mouse (controlled by the trackball).

The code mentioned encloses the PCE and the PCD boards.

In the tables below there are some characteristic data of the board:

DSM 1

9/-2 :;/-<
CPU Intel Pentium 200 MHz MMX (or superior)
RAM 64 Mbytes (or superior)
External SCSI connector type 25 pin, high density
SCSI interface
Operating system Windows NT 4.0, English version
Video output VGA

The following table describes the characteristics of the H. D.:

HD drive 4.3 Gbyte (or superior)

!"#!"$$$$$$$$$$$$=9>*$*?@@9:A*

Opening the Bios there are the following voices:

- Standard CMOS setup

- Advanced CMOS setup
- Advanced Chipset setup
- PCI / Plug and Play setup
- Peripheral setup
- Auto-detect Hard Disks
- Change User Password (disabled)

4-74
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

- Change Supervisor password

- Auto Configuration with optimal settings
- Auto Configuration with fail save settings
- Save Settings and Exit
- Exit without saving

!"#$"%$&'() & *!+,

Floppy Drive A: 1.44Mb 3 1/2

Floppy Drive B: Not installed
Type 32 BIT MODE

Primary Master AUTO Off

Primary Slave AUTO Off
Secondary Master AUTO Off
Secondary Slave AUTO Off
Boot Sector virus protection Disabled

"$-"#'*$&'() & *!+,

1st Boot Device IDE-0

2nd Boot Device Floppy
3rd Boot Device CD-ROM
4th Boot Device Disabled
Boot from card BIOS Yes
Try other Boot devices Yes
S.M.A.R.T. for Hard Disks Disabled
Quick Boot Enabled
BootUp Num-Lock On
Floppy drive swap Disable
Floppy access control Normal
HDD access control Normal
PS/2 Mouse support Disabled
Primary display VGA/EGA
Password Check Setup
Boot to OS/2 No
Internal Cache Enabled
External cache Enabled
System Bios cacheable Enabled
Video Bios shadow Cached

"$-"#'*$&'./, *!& *!+,

Read speculative Disabled

Edo Read WS X-2-2-2

4-75
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

PAGE mode Read WS X-3-3-3

DRAM write WS X-2-2-2
Slow refresh 60 us
Pipelined function Enabled
Dram Data integrity mode Parity
Primary Frame buffer 2 MB
VGA Frame buffer Enabled
Data Merge Enabled
Passive Release Enabled
ISA Line buffer Enabled
Delay Transaction Disabled
AT BUS clock AUTO
Memory hole at 15-16 MB Disabled
16 Bit ISA I/O command wait 2-wait
16 Bit ISA memory command wait 2-wait

!"#$# %&'#()*# %(+#,-.&

Plug and Play aware OS No
PCI latency timer (PCI Clocks) 64
PCI VGA Palette Snoop Disabled
Off board PCI IDE Card AUTO
Off board PCI IDE Primary IRQ Disabled
Off board PCI IDE Secondary IRQ Disabled
DMA Channel 0 PnP
DMA Channel 1 PnP
DMA Channel 3 PnP
DMA Channel 5 PnP
DMA Channel 6 PnP
DMA Channel 7 PnP
IRQ 3 PCI/PnP
IRQ 4 PCI/PnP
IRQ 5 ISA/EISA
IRQ 7 PCI/PnP
IRQ 9 PCI/PnP
IRQ 10 ISA/EISA
IRQ 11 PCI/PnP
IRQ 12 PCI/PnP

-/" 0-/(%#,-.&
On Board FDC AUTO
On Board Serial Port1 AUTO
Serial Port1 Duplex Half
On board Serial Port2 AUTO
Serial Port2 Duplex Half
4-76
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

On Board Parallel Port AUTO

Parallel port mode Normal
EPP version N/A
Parallel port DMA channel N/A
Parallel port IRQ AUTO
On Board primary IDE Enabled
On Board secondary IDE Enabled

The menu’: “Auto Configuration with optimal settings” and “Auto Configuration with fail
save settings” do not restore the Esaote settings but the default settings of the PC
motherboard that are different from the Esaote ones.
Selecting this voice you delete the Esaote settings and the unit won’t work.

4-77
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$$$$%&'()*+$",-..$/%0$$$$$$$$$$$$$$$$$$$$$1"2"1312"2$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

Starting from Technos unit s/n 4172 a new type of DSM1 has been introduced; a
Celeron one has replaced the old CPU board Pentium type.
This new board has the same purposes of the old one.
The board is the controller of the entire unit.
It is a standard PC board assembled on an Esaote board (PCE) with the base peripherals
(external modules):

serial, parallel, SCSI, LAN.

The CPU (DSM1) is connected by the PCE to the MBU and with flat cables to the VCB1
and VCB2. With its internal SCSI connects the magneto optical drive. In case of DVD SCSI
also it’s connected to SCSI.
The Hard disk drive, where there is the program of the unit, the CD-ROM drive (or the new
DVD IDE) is connected to the board by the internal IDE port.
On it arrives also the alphanumeric keyboard and the mouse (controlled by the trackball).
The PCD receives from the CPU the VGA video signal used to synchronise the video output
of the unit. The code mentioned encloses the PCE and the PCD boards.
The differences among the various IC are summarised in the following table.
There is not full compatibility among the CPU/DSM.

/% )/445657%5 %8+&-9/:/;/9<

0 to 1 Removed the VGA board and No compatibility with other IC

used the internal VGA of the
motherboard
1 to 2 Modification to the SoundBlaster
Compatible with IC=0, no with
board (added a capacitor) higher IC
2 to 3 Replacement of the SCSI board No compatible, in case of
Adaptec with Tekram replacement of IC 2 with next
releases it’s necessary to reinstall
the software in the HDD
3 to 4 Modification on the BIOS SCSI Full compatibility between IC 3
of Tekram SCSI board and 4, no compatibility between
IC 2 and 4

In the tables below there are some characteristic data of the CPU/DSM1 board:

DSM

/=>? 7@=>A
CPU Celeron 533 MHz (or superior)
RAM 128 Mbytes (or superior)
External SCSI connector type 25 pin, high density
SCSI interface

4-78
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

Operating system Windows NT 4.0, English version

Video output VGA

The following table describes the characteristics of the new H. D.:

HD drive 17 Gbyte (or superior)

!"#!"$$$$$$$$$$$$%&'($()**&+,(

The Bios settings are the same for the IC 1, 2, 3 and 4. Opening the Bios there are the
following voices:

- Standard CMOS setup

- BIOS features setup
- Chipset features setup
- Power management setup
- PCI / Plug and Play setup
- Load BIOS Default
- Load Setup Default
- Integrated peripherals
- Supervisor password
- User Password
- IDE HDD Auto detection
- Save Settings and Exit
- Exit without saving

(*-+.-/.$01'($()*23

Floppy Drive A : 1.44Mb , 3,5 In (if there is the floppy drive)

Floppy Drive A : None (if there is the M.O.)
Floppy Drive B : None
Type MODE

Primary Master AUTO AUTO

Primary Slave AUTO AUTO
Secondary Master AUTO AUTO
Secondary Slave AUTO AUTO

The following voices of configuration of the Primary Master and Slave and Secondary
Master ad Slave are all the same: SIZE = OM, CYLS = 0, HEAD = 0, PRECOMP = 0,
LAND Z = 0, SECTOR = 0

Video EGA/VGA
Halt on All errors

4-79
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$%&'()*&#$#&()+
Anti-virus protection Disabled
CPU Internal cache Enabled
External cache Enabled
CPU L2 cache ECC checking Enabled
Processor Number Feature Enabled
Quick power on self test Enabled
Boot sequence A , C , SCSI
Swap Floppy drive Disabled
Boot up floppy seek Enabled
Boot Up Num-Lock status On
Gate A20 option Fast
Typematic rate setting Disabled
Typematic rate (chars/sec) 6
Typematic Delay (Msec) 250
Security option Setup
PCI/VGA palette snoop Disabled
OS select for Dram >64 MB Non-OS2
Report no FDD For Win 95 Yes
Video Bios Shadow Enabled
C8000-CBFFF Shadow Disabled
CC000-CFFFF Shadow Disabled
D0000-D3FFF Shadow Disabled
D4000-D7FFF Shadow Disabled
D8000-DBFFF Shadow Disabled
DC000-DFFFF Shadow Disabled

,-!+#&($%&'()*&#$#&()+
Auto configuration Enabled
EDO DRAM Speed selection 60 ns
SDRAM RAS TO CAS delay 3
SDRAM RAS precharge time 2
SDRAM CAS latency time 2
SDRAM precharge control Disabled
DRAM data integrity mode Non-ECC
System BIOS cacheable Disabled
Video BIOS cacheable Enabled
Video RAM cacheable Enabled
8 Bit I/O recovery time 3
16 Bit I/O recovery time 2
Memory hole at 15-16 MB Disabled
Passive release Enabled
Delay transaction Disabled
AGP Aperture Size (MB) 64
4-80
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

Auto detect DIMM/PCI clk Enabled

Spread Spectrum Disabled
CPU host clock Disabled
CPU warning temperature 66°C/151°F
Shutdown Temperature 75°C/167°F

!"#$%&'(')#&#(*%+#*,
ACPI function Enabled
Power management User define
PM control by APM Yes
Video off method V/H sync + Blank
Video off after Standby
Modem use IRQ 3
Doze mode Disable
Standby mode Disable
Suspend mode Disable
HDD power down Disable
Throttle Duty cycle 62.5%
PCI/VGA Act monitor Disabled
Soft off by PWR-BTTN Instant-off
Power On by ring Enabled
Resume by alarm Disabled
IRQ 8 break suspend Disabled

**Reload Global Time Events**

IRQ [3-7 , 9-15] , NMI Disabled

Primary IDE 0 Disabled
Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
Floppy disk Disabled
Serial Port Enabled
Parallel Port Disabled

( - ./%.!(0/),$'*/!(
PnP OS installed Yes
Resources controlled by Manual
Reset configuration data Disabled
IRQ 3 assigned to Legacy ISA
IRQ 4 assigned to Legacy ISA
IRQ 5 assigned to Legacy ISA
IRQ 7 assigned to PCI/ISA PnP
IRQ 9 assigned to PCI/ISA PnP
4-81
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

IRQ 10 assigned to PCI/ISA PnP

IRQ 11 assigned to Legacy ISA
IRQ 12 assigned to PCI/ISA PnP
IRQ 14 assigned to PCI/ISA PnP
IRQ 15 assigned to PCI/ISA PnP
DMA-0 assigned to PCI/ISA PnP
DMA-1 assigned to PCI/ISA PnP
DMA-3 assigned to PCI/ISA PnP
DMA-5 assigned to PCI/ISA PnP
DMA-6 assigned to PCI/ISA PnP
DMA-7 assigned to PCI/ISA PnP
Used mem Base addr. N/A

!"#$%&"#'()#% )*#%&+,

IDE HDD block mode Enabled

IDE primary master PIO Auto
IDE primary slave PIO Auto
IDE secondary master PIO Auto
IDE secondary slave PIO Auto
IDE primary master UDMA Auto
IDE primary slave UDMA Auto
IDE secondary master UDMA Auto
IDE secondary slave UDMA Auto
On-Chip Primary PCI IDE Enabled
On-Chip Secondary PCI IDE Enabled
Onboard PCI SCSI chip Enabled
USB keyboard support Disabled
Init display first PCI slot
KBC input clock 8 MHz
Onboard FDC controller Enabled
Onboard Serial port 1 3F8/IRQ4
Onboard Serial port 2 2F8/IRQ3
UART mode select Normal
On board parallel port 378/IRQ7
Parallel port mode SPP
PWR on after PWR fail Off

The menu’: “Load bios default” and “Load setup defaults” do not restore the Esaote settings
but the default settings of the PC motherboard that are different from the Esaote ones.
Selecting this voice you delete the Esaote settings and the unit won’t work.

,-)#%. ,/%()&,,0/%'

The password selected is: MISTRAL

4-82
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$$$$%&'()*+$,$-./0$1)$20$$$$$$$$$$$$$$$$$$$$3"4"353""4$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

This board is the controller of the entire unit.

It is a standard PC board assembled on an Esaote board (PCE) with the base peripherals
(external modules):

serial, parallel, SCSI, LAN.

Furthermore has on it a Falcon board for acquisitions 3D FH (Free Hand), enabled for all
the probes available for TechnosMP and TechnosMPX.

The CPU (DSM2) is connected by the PCE to the MBU and with flat cables to the VCB1
and VCB2.
With its internal SCSI connects the magneto optical drive. In case of DVD SCSI also it is
connected to SCSI. The Hard disk drive, where there is the program of the unit, and the CD-
ROM drive (or the DVD IDE) are connected to the board by the internal IDE port.
On it arrives also the alphanumeric keyboard and the mouse (controlled by the trackball).
The PCD receives from the CPU the VGA video signal used to synchronise the video output
of the unit. The code mentioned encloses the PCE and the PCD boards.

In the tables below there are some characteristic data of the board:

DSM

.678 9:67;
CPU Pentium III 700 MHz (or superior)
RAM 512 Mbytes (or superior)
External SCSI connector type 25 pin, high density
SCSI interface
Operating system Windows NT 4.0, English version
Video output VGA

The following table describes the characteristics of the new H. D.:

HD drive 17 Gbytes (or superior)

!"#!"$$$$$$$$$$$$<.=*$*>//.9?*

The Bios settings are the same for the all the IC. Opening the bios there are the following
voices:

- Standard CMOS setup

- BIOS features setup
- Chipset features setup

4-83
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

- Power management setup

- PCI / Plug and Play setup
- Load BIOS Default
- Load Setup Default
- Integrated peripherals
- Supervisor password
- User Password
- IDE HDD Auto detection
- Save Settings and Exit
- Exit without saving

!"#$"%$&'() & *!+,

Floppy Drive A: None

Floppy Drive B: None
Type MODE

Primary Master AUTO AUTO

Primary Slave AUTO AUTO
Secondary Master AUTO AUTO
Secondary Slave AUTO AUTO

The following voices of configuration of the Primary Master and Slave and Secondary
Master ad Slave are all the same: SIZE = OM, CYLS = 0, HEAD = 0, PRECOMP = 0,
LAND Z = 0, SECTOR = 0

Video EGA/VGA
Halt on All errors

-.) &/*"!+%* & *!+,

Anti-virus protection Disabled

CPU Internal cache Enabled
External cache Enabled
CPU L2 cache ECC checking Enabled
Processor Number Feature Enabled
Quick power on self test Enabled
Boot sequence A , C , SCSI
Swap Floppy drive Disabled
Boot up floppy seek Enabled
Boot Up Num-Lock status On
Gate A20 option Fast
Typematic rate setting Disabled
Typematic rate (chars/sec) 6
Typematic Delay (Msec) 250
Security option Setup

4-84
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

PCI/VGA palette snoop Disabled

OS select for Dram >64 MB Non-OS2
Report no FDD For Win 95 Yes
Video Bios Shadow Enabled
C8000-CBFFF Shadow Disabled
CC000-CFFFF Shadow Disabled
D0000-D3FFF Shadow Disabled
D4000-D7FFF Shadow Disabled
D8000-DBFFF Shadow Disabled
DC000-DFFFF Shadow Disabled

!"#$%&'(%)&*+%$'$%&*#
Auto configuration Enabled
EDO DRAM Speed selection 60 ns
SDRAM RAS TO CAS delay 3
SDRAM RAS precharge time 2
SDRAM CAS latency time 2
SDRAM precharge control Disabled
DRAM data integrity mode Non-ECC
System BIOS cacheable Disabled
Video BIOS cacheable Enabled
Video RAM cacheable Enabled
8 Bit I/O recovery time 3
16 Bit I/O recovery time 2
Memory hole at 15-16 MB Disabled
Passive release Enabled
Delay transaction Disabled
AGP Aperture Size (MB) 64
Auto detect DIMM/PCI clk Enabled
Spread Spectrum Disabled
CPU host clock Disabled
CPU warning temperature 66°C/151°F
Shutdown Temperature 75°C/167°F

#,-%+'.)/)0%.%/&'$%&*#
ACPI function Enabled
Power management User define
PM control by APM Yes
Video off method V/H sync + Blank
Video off after Standby
Modem use IRQ 3
Doze mode Disable
Standby mode Disable
Suspend mode Disable
4-85
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

HDD power down Disable

Throttle Duty cycle 62.5%
PCI/VGA Act monitor Disabled
Soft off by PWR-BTTN Instant-off
Power On by ring Enabled
Resume by alarm Disabled
IRQ 8 break suspend Disabled

**Reload Global Time Events**

IRQ [3-7, 9-15], NMI Disabled

Primary IDE 0 Disabled
Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
Floppy disk Disabled
Serial Port Enabled
Parallel Port Disabled

! " #$%#&!'$()*+,$&!
PnP OS installed Yes
Resources controlled by Manual
Reset configuration data Disabled
IRQ 3 assigned to Legacy ISA
IRQ 4 assigned to Legacy ISA
IRQ 5 assigned to Legacy ISA
IRQ 7 assigned to Legacy ISA
IRQ 9 assigned to PCI/ISA PnP
IRQ 10 assigned to PCI/ISA PnP
IRQ 11 assigned to Legacy ISA
IRQ 12 assigned to PCI/ISA PnP
IRQ 14 assigned to PCI/ISA PnP
IRQ 15 assigned to PCI/ISA PnP
DMA-0 assigned to PCI/ISA PnP
DMA-1 assigned to PCI/ISA PnP
DMA-3 assigned to PCI/ISA PnP
DMA-5 assigned to PCI/ISA PnP
DMA-6 assigned to PCI/ISA PnP
DMA-7 assigned to PCI/ISA PnP
Used mem Base addr. N/A

4-86
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$%&"#'()#% )*#%&+,

IDE HDD block mode Enabled

IDE primary master PIO Auto
IDE primary slave PIO Auto
IDE secondary master PIO Auto
IDE secondary slave PIO Auto
IDE primary master UDMA Auto
IDE primary slave UDMA Auto
IDE secondary master UDMA Auto
IDE secondary slave UDMA Auto
On-Chip Primary PCI IDE Enabled
On-Chip Secondary PCI IDE Enabled
Onboard PCI SCSI chip Enabled
USB keyboard support Disabled
Init display first PCI slot
KBC input clock 8 MHz
Onboard FDC controller Enabled
Onboard Serial port 1 3F8/IRQ4
Onboard Serial port 2 2F8/IRQ3
UART mode select Normal
On board parallel port 378/IRQ7
Parallel port mode SPP
PWR on after PWR fail Off

The menu’: “Load bios default” and “Load setup defaults” do not restore the Esaote settings
but the default settings of the PC motherboard that are different from the Esaote ones.
Selecting this voice you delete the Esaote settings and the unit won’t work.

,-)#%. ,/%()&,,0/%'

The password selected is: MISTRAL

4-87
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$$$$%&'()*+$,$-./0$,)$123$$$$$$$$$$$$$$$$$$$#"4"#5#6"4$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

This board has the same characteristics of the DSM2, so it’s the controller of the entire unit.
It is a standard PC board assembled on an Esaote board (PCE) with the base peripherals
(external modules):

serial, parallel, SCSI, LAN.

Furthermore has on it a Falcon board for acquisitions 3D FH (Free Hand), enabled for all
the probes available for TechnosMP and TechnosMPX, and the Ascension board with
transmitter and receiver for acquisitions 3D with “Flock of Birds” technology (FoB),
enabled for some probes.

The CPU (DSM3) is connected by the PCE to the MBU and with flat cables to the VCB1
and VCB2. With its internal SCSI connects the magneto optical drive. In case of DVD SCSI
also it is connected to SCSI.
The Hard disk drive, where there is the program of the unit, and the CD-ROM drive (or the
DVD IDE) are connected to the board by the internal IDE port.
On it arrives also the alphanumeric keyboard and the mouse (controlled by the trackball).
The PCD receives from the CPU the VGA video signal used to synchronise the video output
of the unit.
The code mentioned encloses the PCE and the PCD boards.

The first hardware release installed is with IC (index of configuration) 3,

In the tables below there are some characteristic data of the board:

DSM

.789 :278;
CPU Pentium III 700 MHz (or superior)
RAM 512 Mbytes (or superior)
External SCSI connector type 25 pin, high density
SCSI interface
Operating system Windows NT 4.0, English version
Video output VGA

The following table describes the characteristics of the new H. D.:

HD drive 17 Gbytes (or superior)

4-88
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#!"$$$$$$$$$$$$%&'($()**&+,(

The Bios settings are the same for the all the IC. Opening the bios there are the following
voices:

- Standard CMOS setup

- BIOS features setup
- Chipset features setup
- Power management setup
- PCI / Plug and Play setup
- Load BIOS Default
- Load Setup Default
- Integrated peripherals
- Supervisor password
- User Password
- IDE HDD Auto detection
- Save Settings and Exit
- Exit without saving

(*-+.-/.$01'($()*23

Floppy Drive A: None

Floppy Drive B: None
Type MODE

Primary Master AUTO AUTO

Primary Slave AUTO AUTO
Secondary Master AUTO AUTO
Secondary Slave AUTO AUTO

The following voices of configuration of the Primary Master and Slave and Secondary
Master ad Slave are all the same: SIZE = OM, CYLS = 0, HEAD = 0, PRECOMP = 0,
LAND Z = 0, SECTOR = 0

Video EGA/VGA
Halt on All errors

%&'($4)-*2/)($()*23

Anti-virus protection Disabled

CPU Internal cache Enabled
External cache Enabled
CPU L2 cache ECC checking Enabled
Processor Number Feature Enabled
Quick power on self test Enabled

4-89
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

Boot sequence A , C , SCSI

Swap Floppy drive Disabled
Boot up floppy seek Enabled
Boot Up Num-Lock status On
Gate A20 option Fast
Typematic rate setting Disabled
Typematic rate (chars/sec) 6
Typematic Delay (Msec) 250
Security option Setup
PCI/VGA palette snoop Disabled
OS select for Dram >64 MB Non-OS2
Report no FDD For Win 95 Yes
Video Bios Shadow Enabled
C8000-CBFFF Shadow Disabled
CC000-CFFFF Shadow Disabled
D0000-D3FFF Shadow Disabled
D4000-D7FFF Shadow Disabled
D8000-DBFFF Shadow Disabled
DC000-DFFFF Shadow Disabled

!"#$%&'(%)&*+%$'$%&*#
Auto configuration Enabled
EDO DRAM Speed selection 60 ns
SDRAM RAS TO CAS delay 3
SDRAM RAS precharge time 2
SDRAM CAS latency time 2
SDRAM precharge control Disabled
DRAM data integrity mode Non-ECC
System BIOS cacheable Disabled
Video BIOS cacheable Enabled
Video RAM cacheable Enabled
8 Bit I/O recovery time 3
16 Bit I/O recovery time 2
Memory hole at 15-16 MB Disabled
Passive release Enabled
Delay transaction Disabled
AGP Aperture Size (MB) 64
Auto detect DIMM/PCI clk Enabled
Spread Spectrum Disabled
CPU host clock Disabled
CPU warning temperature 66°C/151°F
Shutdown Temperature 75°C/167°F

4-90
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

!"#$%&'(')#&#(*%+#*,
ACPI function Enabled
Power management User define
PM control by APM Yes
Video off method V/H sync + Blank
Video off after Standby
Modem use IRQ 3
Doze mode Disable
Standby mode Disable
Suspend mode Disable
HDD power down Disable
Throttle Duty cycle 62.5%
PCI/VGA Act monitor Disabled
Soft off by PWR-BTTN Instant-off
Power On by ring Enabled
Resume by alarm Disabled
IRQ 8 break suspend Disabled

**Reload Global Time Events**

IRQ [3-7, 9-15], NMI Disabled

Primary IDE 0 Disabled
Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
Floppy disk Disabled
Serial Port Enabled
Parallel Port Disabled

( - ./%.!(0/),$'*/!(
PnP OS installed Yes
Resources controlled by Manual
Reset configuration data Disabled
IRQ 3 assigned to Legacy ISA
IRQ 4 assigned to Legacy ISA
IRQ 5 assigned to Legacy ISA
IRQ 7 assigned to Legacy ISA
IRQ 9 assigned to PCI/ISA PnP
IRQ 10 assigned to PCI/ISA PnP
IRQ 11 assigned to Legacy ISA
IRQ 12 assigned to Legacy ISA
IRQ 14 assigned to PCI/ISA PnP
IRQ 15 assigned to PCI/ISA PnP
DMA-0 assigned to PCI/ISA PnP
4-91
 ESAOTE S.p.a. TECHNOS FAMILY SERVICE MANUAL 8310055000 Rev. A 2003

DMA-1 assigned to PCI/ISA PnP

DMA-3 assigned to PCI/ISA PnP
DMA-5 assigned to PCI/ISA PnP
DMA-6 assigned to PCI/ISA PnP
DMA-7 assigned to PCI/ISA PnP
Used mem Base addr. N/A

!"#$%&"#'()#% )*#%&+,

IDE HDD block mode Enabled

IDE primary master PIO Auto
IDE primary slave PIO Auto
IDE secondary master PIO Auto
IDE secondary slave PIO Auto
IDE primary master UDMA Auto
IDE primary slave UDMA Auto
IDE secondary master UDMA Auto
IDE secondary slave UDMA Auto
On-Chip Primary PCI IDE Enabled
On-Chip Secondary PCI IDE Enabled
Onboard PCI SCSI chip Enabled
USB keyboard support Disabled
Init display first PCI slot
KBC input clock 8 MHz
Onboard FDC controller Enabled
Onboard Serial port 1 3F8/IRQ4
Onboard Serial port 2 2F8/IRQ3
UART mode select Normal
On board parallel port 378/IRQ7
Parallel port mode SPP
PWR on after PWR fail Off

The menu’: “Load bios default” and “Load setup defaults” do not restore the Esaote settings
but the default settings of the PC motherboard that are different from the Esaote ones.
Selecting this voice you delete the Esaote settings and the unit won’t work.

,-)#%. ,/%()&,,0/%'

The password selected is: MISTRAL

4-92