Scribd
Upload
296 views

Control4 Square Wired Keypad Installation Guide

Lighting Control

Uploaded by

Ryan Jones
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
296 views

Control4 Square Wired Keypad Installation Guide

Lighting Control

Uploaded by

Ryan Jones
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

™

Square Warnings and Considerations

Configurable IMPORTANT! Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any

Wired Keypad damage incurred with the misuse of this product. See “Troubleshooting.”

Installation Guide IMPORTANT! Do NOT use a power screwdriver to install this device. If you
do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.

IMPORTANT! This is an electronic device with intricate components.


Supported Model Handle and install with care!

đŏ C4-SKCB-XX Square Configurable Wired Keypad CAUTION! Do not exceed the number of keypads per power supply
as indicated in the Keypad Bus Wiring Guide. Exceeding the maximum
number of keypads will result in overheating the wires and/or failed
Introduction devices.

The Control4® Square Configurable Wired Keypad is intended for use in a Control4 ATTENTION! Ne pas dépasser le nombre de claviers par bloc
system. It installs in a standard UK square wallbox. Communication to the Control4 d’alimentation comme indiqué dans le Guide de câblage du clavier. Si vous
system is via RS-485 protocol and wiring. For RS-485 wiring topologies, refer to dépasser le nombre maximal de claviers les fils et / ou dispositifs pourrai
the document Keypad Bus Wiring Guide. surchauffer.

Box Contents Installation Instructions


đŏ Square Configurable Wired Keypad CAUTION! When wiring the keypad, make sure that either:
đŏ Keycap Button Kit đŏ The Bus Power Supply is not powered on.
đŏ Pluggable Terminal Block - OR -
đŏ Warranty Card đŏ The pluggable connector is disconnected from the Bus Power Supply.

ATTENTION! Lors du branchement du clavier, assurez-vous que


Specifications đŏ Le Bus d’alimentation n’est pas sous tension ou
đŏ La prise est déconnecté de l’alimentation.
The specifications are described below.
1 Prepare the cable for termination by stripping the outer sheath and individual
wires, and then wire into the pluggable terminal block.
Model Number C4-SKCB-XX
2 Wire the keypads as shown below.
Power Requirements 48VDC
Power Consumption Maximum 48VDC 1.2W
Minimum 48VDC 0.7W Figure 1. Keypad Wiring
Environmental
Operational Temperature 32˚F - 104˚F (0˚C - 40˚C) KeyPad KeyPad

Humidity 5% to 95% non-condensing


V+ D+ D- GND V+ D+ D- GND
Storage -4˚F - 158˚F (-20˚C - 70˚C)
Miscellaneous
Control Communications RS-485
Weight 0.1 lb. (0.045 kg)
To Next Keypad
Shipping Weight 0.3 lb. (0.14 kg)
To Bus Ethernet
Gateway

3 Fit the wires back into the wallbox.


4 Align the keypad to the wallbox (observe the orientation direction arrow),
then fasten it with the included screws.

IMPORTANT! Tighten the screws until the device is flush with the
wall surface, but no further. Overtightening can warp the keypad and
cause it to malfunction.
5 Install the buttons following the instructions in the Keypad Buttons Installation
Regulatory/Safety Information
Guide.
To review Regulatory information for your particular Control4 products, see the
6 Install the Control4 faceplate (sold separately) by placing the top of the information located on the Control4 website at:
faceplate on the device and firmly pressing the bottom until the faceplate http://www.control4.com/regulatory/.
snaps into place against the wall.

NOTE: To remove the faceplate, use a flathead screwdriver. Insert the


Patent Information
screwdriver into the small gap on the bottom between the faceplate and Applicable patents are available at: http://www.control4.com/legal/patents.
the device. Twist the screwdriver blade to pop the faceplate off.

7 Ensure that the Bus Power Supply is installed correctly and powered on. For Warranty
instructions, see the Bus Power Supply, 48V Installation Guide. For complete warranty information, including details on consumer legal rights as
well as warranty exclusions, review the Warranty card or visit:
www.control4.com/warranty.
Wiring Diagrams

For bus wiring details, refer to the Keypad Bus Wiring Guide.

Operation and Configuration


On initial power up, all status LEDs on the keypad will illuminate green, indicating
that the device has power. Until the keypad has been configured into a Control4
system, it will not control any loads. To set up this keypad for use with a Control4
system, refer to the Composer Pro User Guide.

Button Tap Sequences

The button tap sequences are defined in the table below. Button tap sequences
that require a single (1) button should use the top-most button installed on the
keypad. Button tap sequences requiring two (2) buttons should use the top-most
and bottom-most (or bottom-left) buttons installed on the keypad.

Function Button Sequence


Identify 4
Reboot 15
Factory Reset 9-4-9
Unidentify 13-4-13

Troubleshooting
If the LEDs do not light up indicating that the keypad is receiving power::

đŏ Ensure that the Bus Power Supply is powered on.


đŏ Ensure that the Bus Ethernet Gateway is powered on and connected.
đŏ Check for proper wiring (see “Installation Instructions” above).
đŏ For help on the installation or operation of this product, email or call the
Control4 Technical Support Center. Provide your exact model number.
Contact [email protected] or see the website www.control4.com

Care and Cleaning


đŏ Do NOT paint the keypad or its wall plate.
đŏ Do NOT use any chemical cleaners to clean the keypad.
đŏ Clean surface of the keypad with a soft damp cloth as needed.

Copyright ©2014 Control4. . All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation
in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners Pricing and specifications are subject to change without notice
200-00367 Rev. B 01/16/14 (BN)

You might also like