10 VI June 2022

https://doi.org/10.22214/ijraset.2022.43770
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

Design Analysis and Fabrication of Atmospheric

Water Generator
J. Venkatesh1, G. Nandakumar2, P. Parthiban3, R. Prabhu4 , P. Sabarishwaran5
1
Assistant Professor, 2,3,4,5Students, Department of Mechanical Engineering, KSR College of Engineering, Tiruchengode,
India
Abstract: The Atmosphere contains water in the form of water vapor, moisture etc. Within that amount almost 35% of
the water is wasted. This amount of water can be used with the help of an Atmospheric Water Generator. This device is
capable of converting atmospheric moisture directly into usable and even drinking water. In many countries like India,
there are many places which are situated in temperate region; there are desert, rain forest areas and even flooded areas
where atmospheric humidity is eminent. But resources of water are limited.
Keywords: Condenser, Compressor, Refrigeration and water.

I. INTRODUCTION
The Atmosphere contains water is in the form of water vapor, moisture etc. Within that amount almost 40% of the water is
wasted. This amount of water can use with the help of an Atmospheric Water Generator. This device is capable of convert
atmospheric moisture directly into usable and even drinking water. The device uses the principle of latent heat to converts
water vapor molecules into water droplets. In many countries like India, there are many places which are situated in
temperate region; there are desert, rain forest areas and even flooded areas where atmospheric humidity is eminent in that
places. But resources of water are limited. In the past few years ago, some projects have already been done to establish the
concept of air condensation as well as generation of water. So, this project will be helping to extend to the applications of
such devices further in the near future. According to previous knowledge, we know that the requires to condense water is
known as dew point temperature. Here, the goal is to obtain the specific temperature practically or experimentally to
condense water with the help of some electronics devices. This project consists of a bicycle-gear arrangement for running a
condenser which is use create the environment of water condensing temperature or dew point, indeed conventional
compressor and evaporator system could also be use condense water by simply exchanging the latent heat of coolant inside
the evaporator. The condensed water will be collected used for drinking purpose and various other uses.

II. METHODOLOGY
Vapor-compression refrigeration is the most widely used method for air-conditioning in today’s world. The vapor-compression
consists of a circulating liquid refrigerant as the medium which absorbs and removes heat from the space to be cooled and
subsequently rejects that heat to the atmosphere. Fig 1 depicts a single-stage vapor-compression system. Basically, the system
has four components: a compressor, a condenser, a thermal expansion valve and an evaporator. Circulating refrigerant enters the
compressor as saturated vapor and is compressed. This results in high pressure which in turn is responsible for higher
temperature. The compressed vapor then comes out as superheated vapor and attains a temperature and pressure at which
condensation can take place with the help of cooling water or cooling air. That hot vapor is passed through a condenser where it
is cooled and condensed. This is where the circulating refrigerant rejects heat from the system. The condensed liquid refrigerant
known as saturated liquid is next passed through an expansion valve where there is a sudden drop in pressure. This results in the
adiabatic flash evaporation of the liquid refrigerant. The Joule-Thomson effect as it is called lowers the temperature of the liquid
and vapor refrigerant mixture which makes it colder than the temperature to be achieved (temperature of the enclosed space).
The cold mixture is passed through the coils in the evaporator. A fan circulates the warm air in the enclosed space across the
coils carrying the cold refrigerant liquid and vapor mixture. That warm air evaporates the liquid part of the cold refrigerant and
at the same time, the circulating air is cooled

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 121
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

Fig. 1. Vapor Compression Refrigeration

and as a result, it lowers the temperature of the enclosed space to the temperature to be achieved. The circulating refrigerant
absorbs and removes heat from the evaporator which is then rejected in the condenser and transferred by the water or air used in
the condenser. For the completion of the refrigeration cycle, the refrigerant vapor coming out of the evaporator which is again a
saturated vapor is returned back into the compressor.

III. COMPONENT DETAILS

A. Compressor
The compressor is the "heart" of a refrigerator. It circulates the refrigerant throughout the system and adds pressure to the
warm part of the circuit, and makes the refrigerant hot. It's similar to when you are pumping air into a bicycle tube - you can
sense a heat increase in the pump while you compress the air. The compressors are one of the most important parts of the
refrigeration cycle. The compressor compresses the refrigerant, which flows to the condenser, where it gets cooled. It then
moves to the expansion valve, and the evaporator and it is finally sucked by the compressor again. For the proper functioning of
the refrigeration cycle, the refrigerant must be compressed to the pressure corresponding to the saturation temperature higher
than the temperature of the naturally available air or water. It is the crucial function that is performed by the compressor.
Compression of the refrigerant to the suitable pressure ensures its proper condensation and circulation throughout the cycle.

Fig. 2. Compressor
Specifications:
Application : LBP
Refrigerant : R134a

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 122
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

Compressor Cooling : Static

Displacement (cc) :4
Evaporating Temperature : 7.2 degrees
Condensing Temperature : 55 degrees
Liquid Sub Cooling Temp : 32.2 degrees
Power / Current : 94 Watts / 0.8 Amps
Rated Voltage : 230V – 50HZ

B. Refrigerant
Refrigerant is a cooling agent that absorbs heat and leaves cool air behind when passed through a compressor and evaporator.
1) R-134a Refrigerant
Components: Hydrofluorocarbon (HFC)
Uses: Refrigerators, Car Air Conditioning
ODP: 0
GWP: 1430 (Medium)
Eco-Friendly: Somewhat
Flammable: No

C. Condenser
The condenser removes heat from the hot refrigerant vapor gas vapor until it condenses into a saturated liquid state
condensation. After condensing, the refrigerant is a high-pressure, low-temperature liquid, at which point it's routed to the loop's
expansion device.

Fig. 3. Condenser
D. Evaporator
The function of the evaporator is to absorb the heat from the space or surrounding medium which is to be cooled by means of
refrigeration. The process of heat removal from the substance to be cooled or refrigerated is done in the evaporator. The liquid
refrigerant is vaporized inside the evaporator (coil or shell) in order to remove heat from a fluid such as air, water etc.
Fig. 4. Evaporator

E. Expansion Valve
An expansion valve or thermostatic expansion valve is a component in vapor-compression refrigeration and air conditioning
systems that controls the amount of refrigerant released into the evaporator and is intended to regulate the superheat of the

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 123
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

refrigerant that flows out of the evaporator to a steady value. Although often described as a "thermostatic" valve, an expansion
valve isn't able to regulate the evaporator's temperature to a precise value. The evaporator's temperature will only vary with
the evaporating pressure, which will have to be regulated through other means (such as by adjusting the compressor's capacity).

Fig. 5. Expansion Valve

F. D.C. Motor
A single-phase D.C motor is an electrically-powered rotary machine that can turn electric energy into mechanical energy. It
works by using a single-phase power supply.
1) Product Description:
Usage/Application – Cooler Motor
Voltage – 220 to 240V
Phase – Single Phase
Commutation – Brush
Speed – 500 to 1500 RPM
Mounting Style – Case Bolt Mount
Frequency - 15 to 20 Hz
Efficiency – 90%
Body Material – Mild Steel

Fig. 6. D.C Motor

G. Air Blower Fan
Fans can create airflow with low pressure but in large volumes and hence they are usually used in big air coolers. But blowers
create high pressure airflow from the cooling system with higher speed and air throw.
1) Product Specifications:
Motor Rating – 0 to 1 HP
Fan Speed – 500 to 600 rpm
Material – Stainless Steel
Blade Material – Plastic

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 124
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

Product Type – Air Blower

Power Source Type – Electric

Fig. 7. Air Blower Fan
H. Lead Acid Battery
The sealed lead-acid battery consists of six cells mounted side by side in a single case. The cells are coupled together, and each
2.0V cells adds up to the overall 12.0V of the battery. A completely charged lead-acid battery is made up of a stack of
alternating lead oxide electrodes, isolated from each other by layers of porous separators. All these parts are placed in a
concentrated solution of sulfuric acid, intercell connectors connect the positive end of one cell the negative end of the next cell
hence the six cells are in series.
1) Product Details:
Voltage – 12 Volts
Current – 8 Ah
Battery Cell Composition – Sealed Lead Acid
Dimensions L*W*H – 11.8 * 11.4 * 11.3 Centimeters
Number of Cells – 6

Fig. 8. Lead Acid Battery

IV. WORKING PRINCIPLE

The Atmospheric Water Generator works on the same principle as a Refrigerator and Air Conditioner. Refrigerators and air
conditioners both work on the principle of cooling through evaporation. The refrigeration process begins with the compressor.
Ammonia gas is compressed until it becomes very hot from the increased pressure. This heated gas flows through the coils
behind the refrigerator, which allow excess heat to be released into the surrounding air. Eventually the ammonia cools down to
the point where it becomes a liquid. This liquid form of ammonia is then forced through a device called an expansion valve.
Since this evaporation occurs at -27 degrees F (-32 degrees Celsius), the ammonia draws heat from the surrounding area. Cold
material, such as the evaporating ammonia gas tend to take heat from warmer materials. As the evaporating ammonia gas
absorbs more heat, its temperature rises. Coils surrounding the lower refrigerator compartment are not as compact. The rate at
which water can be produced depends on relative humidity and ambient air temperature and size of the compressor.
Atmospheric water generators become more effective as relative humidity and air temperature increase. As a rule of thumb,
cooling condensation atmospheric water generators do not work efficiently when the temperature falls below 18.3°C (65°F) or
the relative humidity drops below 30%. This means they are relatively inefficient when located inside air-conditioned offices.
The cost-effectiveness of an AWG depends on the capacity of the machine, local humidity and temperature conditions and the
cost to power the unit. Water is often condensed from the air in the air conditioners when the ambient air is humid and hot in
coastal tropical regions. This water can be conveniently used for drinking purpose. The amount of water vapor at any time is

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 125
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

usually less than that required to saturate the air. The Relative Humidity is a percent of saturation humidity shown in Fig. 9.
Here condenser is placed on roof of the frame. That is connected to the silica gel and evaporate, and compressor. The condenser
is connected all the side of the frame by pin joint. The assembly of various components like Condenser, Compressor,
Evaporator, D.C Motor, Air Blower Fan, Battery, Water Collecting Tank. Shown in Fig. 10.

Fig. 4.1. Block Diagram

Fig. 4.2. Assembled Atmospheric

Water Generator

V. TESTING PROCEDURE
The tests were conducted between April 21st and May 13th, 2022. And used monitoring devices such as a clamp type
multimeter to measure current and voltage, an anemometer to measure airflow inlet and outlet, a thermocouple to measure
airflow temperature, and a hygrograph to measure airflow humidity. Table. l shows the testing positions for temperature, airflow
rate, and relative humidity. The measured data and generated water were recorded once every hour.
Apparatuses Unit Accuracy Range Purpose
Clapometer A V ±(2.5%+15d) ±(1.0%+5d) 400/600 Current and voltage testing

Anemometer m/s ±0.0015 0.4-30.0 Air flow rate testing

Thermocouple c ±0.1 -200-1300 Temperature testing
Hygrograph % ±3 0~99 Air humidity testing
Graduated cylinder ml ±5 50-500 Water generated testing
Table. 1. The specifications of experimental apparatuses used
VI. APPLICATIONS
There are hardly any chances to refuse that this device is portable for its simple design and endurance capability. So, the

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 126
 International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.538
Volume 10 Issue VI June 2022- Available at www.ijraset.com

Atmospheric Water Generator is the device which can be implemented for extreme situation, to use during flood, in desert
areas, and in rural areas. It has great advantages as it works like a renewable source of atmosphere water and doesn’t need a
heavy power source. It can be implemented for Industrial development where the water is a matter of crisis.

VII. ADVANTAGES
1. High Performance: Delivers consistent low dew-point temperatures.
2. High Efficiency: Precools incoming air, cuts operating costs up to 50%.
3. Simple Technology: Simple technology, familiar to HVAC contractors and technicians.
4. Reliable: No moving parts in the airstream, except direct drive fan.
5. Low Maintenance: Direct drive Fans, no belts or pulleys to adjust.
6. Sanitary: Full draining, no standing water.
7. Lower capital costs, competitively priced.
8. Versatile: Available using chilled water or refrigerant.

VIII. CONCLUSION
New weather patterns appeared in our world in the past century, and that caused lots of confusion for humans who used to
expect only one weather pattern per season in certain areas. However, this is not the case in the current days, which means that
people have to change their behaviors in so many ways if they want to have a good life quality for the future generations.
However, it is obvious that finding sustainable alternatives of the traditional natural sources is one of the most important issues
that should be studied and developed, whether for energy source, or water sources. Applying this system in a highly humid
region almost 300 Milliliter of condensed water can be produced per hour during the day light, this is a promising result.
Finally, in this report we talked about way of harvesting water from thin air, and these ideas mentioned above can solve the
poorer arid areas water problems with cheap prices inventions that they can buy or maybe produce their selves. We can produce
an unlimited supply of water without environmental pollution for the current water scarcity problem. Air water is a renewable
source of water so the technology is a secured source for the future.

IX. FUTURE WORK

There have been many things we missed out on enabling our system to be very effective and efficient with the production of
water. However, since it is still in a prototype stage, there are is lot of room for improvements. One of which is, to properly
optimize the system which facilitate the production of water in case of conditions where humidity can be decreased too low.
Secondly, there should also be a need to properly insulate the heat sink to avoid leakage of current and heat which will
eventually improve the efficiency of the whole system. Also, there would be a need of heat sink wall modification to avoid
resting on it and instead is passed straight towards the water container.

REFERENCES
[1] Niewenhuis B, Shepperly C, Beek R.V, Kooten E.V, Water Generator Water from Air Using Liquid Desiccant Method, Vol. 5(6), 2012, Pp. 125-
148.
[2] Pavithra S, Vapour Compression Refrigeration System Generating Fresh Water from Humidity in the Air, Second International Conference on
Sustainable Energy and Intelligent System (SEISCON), 2011, Pp. 75-79.
[3] Kabeela A.E, Abdulazizb M, Emad M.S, Solar Based Atmospheric Water Generator Utilization of a Fresh Water Recovery: A Numerical Study,
International Journal ofAmbient Energy, Vol. 37(1), 2014, Pp. 68-75.
[4] Kim M, Chung J, An Approach for Heat Flux Sensor-Less Heat Inflow Estimation Based on Distributed Parameter System of Peltier Device,
IECON 2011-37th Annual Conference on IEEE Industrial Electronics Society, vol. 10(7), 2011, Pp. 4214-4219.
[5] White S, Cleland D, Peltier Thermoelectric Modules Modelling and Evaluation, International Journal of Engineering (IJE), Vol. 5(1), 2011, Pp.
114-121.
[6] Aye B, Wu D, Solar Chilled Drinking Water Sourced from Thin Air: Modelling and Simulation of a Solar Powered Atmospheric Water
Generator, 20th International Congress on Modelling and Simulation, Australia, Vol. 6(12), 2013, Pp. 42-49.
[7] Anandhulal, Arjun, Athul, Bipin, Basith (2016), “Atmospheric water generation”, International Journal of Scientific and Engineering Research, Vol 7,
Issue 4, pp 398-400.
[8] Sahil Doshi, Shubham Chaudhari, Saheel Aitwade, Ratan Singh, and C. P. Waykole (2016), “Development of Water Generation System from
Air”, International Journal of Current Engineering and Technology, Special Issue-4, pp 202-203.
[9] Mr. Ajinkya Wankhade, Prof. Dr. Harish U. Tiwari (2016), “Extraction of Water from Air using Adsorption Refrigeration System”, International
Journal Engineering Research Journal (IERJ), Special Issue pp 1069-1074.
[10] K. I. V. Vandana1, M. Rajyalakshmi, P. Ramya Sai, T. Sai Bhargav, N. Vinuthna, U. Pranava Koundinya (2017) “A Survey on Extraction of Water
from Air Using Wind Energy”, IJIRSET, Vol 6, Issue 3, pp 3298-3300.

©IJRASET: All Rights are Reserved | SJ Impact Factor 7.538 | ISRA Journal Impact Factor 7.894 | 127