Scribd
Upload
67 views

10.1.3.4 Packet Tracer - Configuring OSPF Advanced Features

Uploaded by

sebastian ruiz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
67 views

10.1.3.4 Packet Tracer - Configuring OSPF Advanced Features

Uploaded by

sebastian ruiz
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Packet Tracer - Configuring OSPF Advanced Features

Topology

Addressing Table

Device Interface IPv4 Address Subnet Mask Default Gateway

G0/0 172.16.1.1 255.255.255.0 N/A


R1 S0/0/0 172.16.3.1 255.255.255.252 N/A
S0/0/1 192.168.10.5 255.255.255.252 N/A
G0/0 172.16.2.1 255.255.255.0 N/A
S0/0/0 172.16.3.2 255.255.255.252 N/A
R2
S0/0/1 192.168.10.9 255.255.255.252 N/A
S0/1/0 209.165.200.225 255.255.255.224 N/A
G0/0 192.168.1.1 255.255.255.0 N/A
R3 S0/0/0 192.168.10.6 255.255.255.252 N/A
S0/0/1 192.168.10.10 255.255.255.252 N/A
PC1 NIC 172.16.1.2 255.255.255.0 172.16.1.1
PC2 NIC 172.16.2.2 255.255.255.0 172.16.2.1
PC3 NIC 192.168.1.2 255.255.255.0 192.168.1.1

Objectives
Part 1: Modify OSPF Default Settings
Part 2: Verify Connectivity

© 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 2
Packet Tracer - Configuring OSPF Advanced Features

Scenario
In this activity, OSPF is already configured and all end devices currently have full connectivity. You will modify
the default OSPF routing configurations by changing the hello and dead timers and adjusting the bandwidth of
a link. Then you will verify that full connectivity is restored for all end devices.

Part 1: Modify OSPF Default Settings


Step 1: Test connectivity between all end devices.
Before modifying the OSPF settings, verify that all PCs can ping the web server and each other.

Step 2: Adjust the hello and dead timers between R1 and R2.
a. Enter the following commands on R1.
R1(config)# interface s0/0/0
R1(config-if)# ip ospf hello-interval 15
R1(config-if)# ip ospf dead-interval 60
b. After a short period of time, the OSPF connection with R2 will fail. Both sides of the connection need to
have the same timers in order for the adjacency to be maintained. Adjust the timers on R2.

Step 3: Adjust the bandwidth setting on R1.


a. Trace the path between PC1 and the web server located at 64.100.1.2. Notice that the path from PC1 to
64.100.1.2 is routed through R2. OSPF prefers the lower cost path.
b. On the R1 Serial 0/0/0 interface, set the bandwidth to 64 Kb/s. This does not change the actual port
speed, only the metric that the OSPF process on R1 will use to calculate best routes.
R1(config-if)# bandwidth 64
c. Trace the path between PC1 and the web server located at 64.100.1.2. Notice that the path from PC1 to
64.100.1.2 is redirected through R3. OSPF prefers the lower cost path.

Part 2: Verify Connectivity


Verify all PCs can ping the web server and each other.

© 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 2

You might also like