GM SERVICE TOOLS
ENGINE, TRANSMISSION, INTERIOR, AXLE, BRAKES, ELECTRICAL & BODY SERVICE
TOOL APPLICATION USE
Belt Tensioner 2.4L GM eAssist engines. 2012- Compresses the belt tensioner spring for easier
Compressor 2016 LaCrosse, 2011-2014 Malibu, engine drive belt replacement and starter
2012-2017 Buick Regal. generator servicing.
Similar to OE tool #EN-48932.
6725
Diesel Fuel Hydrometer Used for testing #1 and #2 grade Test #1 and #2 grade diesel fuel composition
diesel fuels. and combustion characteristics. Helps diagnose
fuel and drivability issues.
6750
Injector Seal Installer 1998-2014 GM engines with SIDI single Installs the Teflon seal onto the end of the injector
and Sizer Adapters seal injectors. to ensure proper injector installation. Includes seal
installer/sizer and pilot cone.
Similar to OE tool #EN-48266.
6757
Evap Access Port Tool All GM 5/16” EVAP line systems. Diagnose all GM 5/16” EVAP line systems. Use
with the OTC 6522 LeakTamer for flow testing
and leak testing.
(Similar to OE tool #CH-48096)
6787
Oil Pressure and 2005-Later GM Gen IV (4) and Gen V (5) Diagnose engine oil system issues. Adapter
Prelube Adapter engines, 4.8L, 5.3L, 6.0L, and 6.2L. installs in place of the spin-on oil filter to connect
pressure gauges to test oil system pressure.
Can also be used to connect prelube equipment
to the engine.
7297 (Similar to OE tool #EN-47971)
GM Duramax Injector 2011-Later 6.6L Duramax Diesel, Isuzu. Assists in removing injectors from the cylinder
Puller head without damaging the injector body.
(Similar to OE tool #EN-49774)
6777
Quick Connect Release 2010-Later GM 2.8L and 6.6L diesel Separates and prevents damage to the 4.8mm
Tool engines. (3/16 inch) hydrocarbon injection quick-connector
to service the fuel line bundle or replace fuel lines
without removing unrelated components.
6739 (Similar to OE tool #CH-49736)
Injector Seal Installer 2010-Later GM 1.4L, 1.5L, 2.0L, 2.4L, 2.5L, Installs the dual seals onto the end of the injector
and Sizer Adapters 3.0L, 3.6L, 4.3L, 5.3L, and 6.2L engines. to ensure proper injector installation. Includes
two seal installation pilots for each groove, a seal
installer driver, and a compression sizer.
Note: Some 2014-Later injectors have larger
injector tips which require 6707 Injector Seal
Installer Adapters.
6756
(Similar to OE tool #EN-49245)
Crankshaft Rear Seal 2001-Later 6.6L Duramax diesel engine Special 3-jaw puller grabs the inner lip of the seal,
Remover found in GMT800, 2500HD, 3500, and preventing damage to the block and crank. Makes
GMT900, GMC Sierra HD and Chevrolet removing crankshaft rear seals easier and faster.
Silverado HD. 2006-2016 Chevrolet (Similar to OE tool #J-44641)
Express, GMC Savana
6740
otctools.com QUESTIONS?
800 533 6127
TOOL APPLICATION USE
Inner Pinion Bearing 1998-2006 Suburban, Tahoe Installs inner pinion bearing race to
Race Installer desired position
(Similar to J-45870 & J-8092)
6723
Axle Seal Protector 2011-Later Protects axle seal from being cut or nicked, both
of which can cause immediate or eventual leaks
(Similar to J-44394-A)
6712
Lift Pad Adapters All Used to properly lift the vehicle with a hoist
(Similar to J-43625)
5267
Air Brake Line Release 2003-Later Medium Duty trucks Separate connectors on the P/S system
Tools and EGR coolers without damage
(Similar to J-45666 & J-42971)
5089
Parasitic Draw Switch All Used with an amp meter to isolate parasitic
amperage draws
(Similar to J-38758)
6945
Camshaft Retaining 2.8L/3.0L/3.6L Lock the camshafts together at TDC to keep them
Tool Set from turning while setting timing
(Similar to EN-48383)
6691
Fuel Sender Lock Ring 2003-2011 Cadillac CTS/SRX/STS Fits the newly designed 4 1/2” lock ring, which
Wrench requires high torque to loosen
and tighten
(Similar to J-45747)
6556
Injector Rail Assembly 2007-2014 GDI Safely remove GDI fuel rails
Remover (Similar to EN-49248)
6706
Crankshaft Seal 2011-2013 Aveo/Cruze/Sonic/Volt Safely installs front crankshaft seal
Installer (Similar to KM-960)
6742
Timing Chain Retainer 2011-Later 2.0L/2.4L Ecotech Retain the timing chain and lower sprocket
positions while servicing the upper sprockets,
camshafts, valve springs, or valve seals
6677
(Similar to EN-48749)
Flywheel Holding Tool 2013-2014 2.0L & 2.5L Holds the flywheel in place for servicing the
balancer or flywheel bolts
(Similar to EN-50792)
6759
TOOL APPLICATION USE
Front Crank Seal 2013-2014 2.0L & 2.5L Allows for the installation of front crank seal
Installer without the removal of the cover
(Similar to EN-50820 & EN48034)
6758
Timing Chain Holding 2013-2014 2.0L & 2.5L Retains the timing chain position relative to
Tool the crankshaft position
(Similar to EN-50656)
6746
Camshaft Actuator 2013-2014 2.0L & 2.5L Holds camshaft actuator in place to safely
Locking Tool remove/install actuator bolt
(Similar to EN-50793)
6745
Tensioner Retaining Pin 2013-2014 2.0L & 2.5L Relieves the tension on the timing chain tensioner
for camshaft, actuator, and timing chain service
6744 (Similar to EN-50837)
Injector Seal Installer 2013-Later 4.3L V6, 5.3L V8 or 6.2L V8 Correctly install the injector seals for
Adapters leak-free operation
(Similar to EN-51105)
6707
Injector Retaining Clip 2013-Later 4.3L V6, 5.3L V8 or 6.2L V8 Removes or installs the injector retaining clips
Replacer without over-spreading to ensure proper
retention of the injector to the rail
6708 (Similar to EN-51097)
Fuel Pump Installation 2013-Later 4.3L V6, 5.3L V8 or 6.2L V8 Verifies that the camshaft fuel pump lobe is at
Gauge base circle position before installing the high
pressure fuel pump
(Similar to EN-51092)
6710
Pan Seal Cutter All Pressed into the sealant and struck with a
hammer in order to cut through the oil pan seals
(Similar to J-37228)
6788
Connecting Rod All Protects the crankshaft bearing surface from
Guides damage by nicking or scratching during piston
and connecting rod removal or installation (w/
6553 M8x1.0 threads)
(Similar to EN-51454)
Steering Column 2005-Later Installs into the steering column to keep the
Anti-Rotation Pin steering wheel orientation correct
2551 (Similar to J-42640)
Door Handle Spring 2014-Later Allows for door handle replacement without
Retainer having to remove the interior door panel
(Similar to BO-51363)
6644
Key Fob Fixture All Allows for quick and safe removal/installation of
GM flip key blades
(Similar to BO-51098)
2550
otctools.com QUESTIONS?
800 533 6127
TOOL APPLICATION USE
Cigarette Lighter All Remove cigarette lighter socket without damage
Socket Remover to socket or dash
2549 (Similar to J-42059)
Torque Converter 1990-2011 FWD Automatic Transmission Installs torque converter seals without damage
Seal Installer (Similar to J-28540-A)
6715
Seal Protector 2013-Later Chevrolet Trax, Buick Encore Protects transfer case Intermediate Drive Shaft
(IDS) seal from splines of the IDS during shaft
removal or installation
6713 (Similar to DT-50937)
Input Shaft Seal 2013-Later Chevrolet Trax, Buick Encore Installs input shaft seal & side extension housing
Installer seals to proper depth
(Similar to DT-50840 & J-8092)
6714
Transmission Adapter 2013-Later Chevrolet Trax, Buick Encore Replaces the mount bushing on the transmission
Plate Bushing Replacer adapter plate
(Similar to DT-50839 & CH-50342)
6702
Shift Rail Seal Installer 2013-Later Manual Transmission Installs the shift seal on the Tremec TR 3160
(Tremec TR 3160) transmission to the proper depth to ensure
optimal seal life
(Similar to DT-51077)
6716
Pump Seal Installer Set 2014-Later Protects, installs and sizes the torque converter
fluid seal ring into the stator support during unit
overhaul
(Similar to DT-51191)
6743
Trans Mainshaft 2014-Later Corvette (Manual) Prevent damage to components and are necessary
Bearing and Gear as the transmission assembly
Installer (Similar to DT-51076 & DT-51076-10)
6724
Trans Case Holding All Adjustable design for adapting to many different
Fixture transmission case configurations
as well as other components
(Similar to J-36842)
7040
GM Duramax 2001-2004 6.6L Duramax engines Designed to pull injectors
Injector Puller (Similar to J-44639)
6778
GM Duramax 2005-2011 6.6L Duramax engines Designed to pull injectors
Injector Puller (Similar to J-46594)
6779
2007_1176 Rev. A
GM Water Pump 2006-2014 2.0L I4 engines Holds the timing chain in place for water pump
Holding Tool 2002- 2008 2.2L I4 engines with replacement or removal. Unique design can be
engine code F installed regardless of timing chain orientation.
2004- 2008 2.4L I4 engines with Keeps timing on GM engines when used properly
engine code B during service.
6616 (Similar to J-43651)
otctools.com QUESTIONS?
800 533 6127
