Scribd
Upload
113 views

Bioscrypt V-Prox™ / V-Pass FX™: Quick Start Guide

Uploaded by

Hopper Daniel Johnson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
113 views

Bioscrypt V-Prox™ / V-Pass FX™: Quick Start Guide

Uploaded by

Hopper Daniel Johnson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Bioscrypt V-Prox™ / V-Pass FX™

Quick Start Guide


Please note that this Quick Start Guide is for use with the MV1610 combo board V-Prox and V-
Pass FX.

Required items for Setup / Installation:


‰ A VeriSeries reader with mounting plate and pigtail connection cable – Included
‰ CD containing: application software, driver for the Serial-to-USB converter and documentation – Included
‰ Security hex key needed to reveal the USB Aux port - Included
‰ A USB cable for programming the reader through the USB Aux port – Included
‰ Computer running Windows 2000 or XP – Not Supplied
‰ DC power supply rated at 9-24V @ 500mA – Not Supplied

Optional items for Setup / Installation:


‰ Networking cable, Wiegand door controller, and Proximity Cards – Not Supplied
‰ RS-232/RS-485 Converter – Not Supplied
‰ External Wiegand Reader using a supported format – Not Supplied

Getting Started
Before installation be sure to complete these 6 steps:
1. Read the VeriSeries Operations Manual and Installation Guide (Documents included on the CD).
2. Read the MVXX Release Notes and VeriAdmin Release Notes on the CD for the most recent updates.
3. Install the VeriAdmin Software (included on CD) on a PC/Laptop running Windows 2000, or XP, to initially set up
the VeriSeries reader. You can install the VeriAdmin software on your computer by inserting the CD in to the
CD-ROM drive. The Installation dialog will pop-up shortly thereafter with system installation instructions.
4. On the same PC/Laptop, install the driver for the Serial-to-USB converter (included on the CD). This driver is
included in a separate folder on the CD (see Installation Guide for more information).
5. Configure VeriSeries readers with correct baud rate, unique Network IDs, etc. (see Setting Up the VeriSeries
Reader section below).
6. Become familiar with VeriSeries reader operations and enrolling users using the VeriAdmin software.

NOTE 1: CAUTION: The silicon sensor used in the VeriSeries product line is an electro-static sensitive device. Pin 15
on the pigtail must be connected to an Earth Ground for reliable operation. Installing a reader without proper grounding
will void the warranty. Refer to the Installation Manual for specific information.
NOTE 2: The VeriSeries reader is shipped with its main communication port (on the pigtail) set for RS-485 connection
with a baud rate of 9600 bits per second. The VeriSeries is shipped with its AUX communication port (USB connection
on the bottom) set to a baud rate of 57600 bits per second (baud).

Setting Up the VeriSeries Reader


‰ Apply power to the VeriSeries reader through the pigtail: connect DC power (9-24 V) to the red wire, and the power
return (power ground) to the black wire. Note: Wire colors have previously been changed. See VeriSeries Pigtail
Connections table below for wire colors.
‰ Connect the programming cable to the USB Aux port at the bottom of the reader after opening with Security hex
key.

Document #430-00118-09 Page 1 of 2 © Copyright 2006 Bioscrypt Inc.


VeriSeries Quick Start Guide All Rights Reserved
.
‰ Run / Open the VeriAdmin software on your PC. Configure the software for the correct PC COMM Port and set the
baud rate to 57600. From this software you will be able to change communications parameters, assign a network
ID, enroll or delete templates, and store/transfer templates on the PC or from reader to reader.
‰ Please refer to the VeriSeries Operations Manual for complete user instructions.

VeriSeries Pigtail Connections


Pin # Prior Color Current Color Signal Connect to
Jacket Grey Blue
1 Red w/Black Green Wiegand Out Data 0 Controller Data 0
2 Green w/Black Green w/White Wiegand In Data 0 Card Reader Data 0
3 Orange White Wiegand Out Data 1 Controller Data 1
4 Orange w/Black White w/Black Wiegand In Data 1 Card Reader Data 1
5 Green Grey TTL Output
6 Red Black w/White Wiegand GND Wiegand GND
7 Blue w/Black Blue w/Black RS-485 (-) RS-485 (-)
8 White Blue RS-485 (+) RS-485 (+)
9 Black w/White Violet RS-232 Tx RS-232 Rx
10 Red w/White Violet w/White RS-232 Rx RS-232 Tx
11 Black Black Power GND Power return
12 Green w/White Black w/Red Signal GND RS-485 GND or
cable shield
13 Blue w/White Red Unregulated input Power (9-24 VDC)
(9-24 VDC)
14 Blue Red/White N/A N/A
15 White w/Black Green w/Yellow Shield Earth Ground

Bioscrypt Technical Support Contact Information:

Telephone: +1 866.304.7180 (toll free US and Canada)


+1 310.760.4130 (direct)

Fax: +1 310.760.4137

Email: [email protected]
Web: http://www.bioscrypt.com

Hours: 5:30A – 5:00P PST (Monday – Friday)

Address: Bioscrypt Inc


Technical Support / RMA Dept.
2101 Rosecrans Ave., Suite 1250
El Segundo, CA 90245 USA

Corporate & Canadian Office U.S. Office U.K. Office


505 Cochrane Drive 2101 Rosecrans Ave, Suite 1250 35 Jackson Court, Hazlemere
Markham, ON, Canada L3R 8E3 El Segundo, CA 90245 High Wycombe, Buckinghamshire
T +1 905.940.7750 T +1 310.760.4101 England HP15 7TZ
F +1 905.940.7642 F +1 310.227.8038 T +44 (0) 1494.814404
www.bioscrypt.com F +44 (0) 1494.815513

Document #430-00118-09 Page 2 of 2 © Copyright 2006 Bioscrypt Inc.


VeriSeries Quick Start Guide All Rights Reserved
.

You might also like