Scribd
Upload
425 views

Advanced VCO Design Using Ansoft Designer

This document summarizes the steps for designing an advanced voltage-controlled oscillator (VCO) using Ansoft Designer. It outlines the VCO specifications, including an oscillation frequency of 1800MHz +/- 30MHz and an output power greater than 4dBm. It then describes creating the device library, designing the resonant circuit and oscillator circuit, adding a buffer amplifier for impedance matching, and performing total system analysis. The final results showed the VCO meeting the oscillation frequency and output power specifications.

Uploaded by

labirint10
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
425 views

Advanced VCO Design Using Ansoft Designer

This document summarizes the steps for designing an advanced voltage-controlled oscillator (VCO) using Ansoft Designer. It outlines the VCO specifications, including an oscillation frequency of 1800MHz +/- 30MHz and an output power greater than 4dBm. It then describes creating the device library, designing the resonant circuit and oscillator circuit, adding a buffer amplifier for impedance matching, and performing total system analysis. The final results showed the VCO meeting the oscillation frequency and output power specifications.

Uploaded by

labirint10
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 32

Advanced VCO Design using Ansoft Designer

Moriaki Ueno Ansoft Japan

Presentation #8

Agenda
w w w w w w w w

About Ansoft Designer VCO specification Device library making Resonant Circuit design Oscillator Circuit design Buffer amp design Total analysis Conclusion

About Ansoft Designer


Communication System Simulation

Integrated environment

High Frequency Circuit Simulation

Planar EM Electro Magnetic Simulation

VCO specifications
w

We intend to design VCO for mobile communications.


w w w w

Oscillation frequency Output power Supply voltage Current consumption

1800MHz +/- 30MHz more than 4dBm 3V 8mA

VCO circuit
w
Vcc

Circuit topology and power estimation


Oscillator Buffer Amp

Output port

Freq. control

Resonant Circuit

Power level ; -3dBm

S21 ; 9dB @2GHz Ic=3mA Power level ; 6dBm

VCO Circuit
w

Parts to use
w

Transistor Varicap Condenser Coil Substrate

w w w w

2SC5668(NE667M03) OSC 2SC5435(NE685M03) Buffer JDV2S13S GRP15, GRP18 series LQW18 series TMM-4 t=0.8mm double sided

Device library making


w

Equivalent circuit for condenser and coil


*

* Parallel resistor added for improve DC current convergence in Harmonic balance analysis

Device library making


w

Equivalent circuit for packaged transistor and diode

chip

chip

package

package

Device library making


w

Write net list and importing library to user-library

Write net list and copy to user-library

Resonant Circuit
w

Microstrip resonator
small condenser added

Practical resonant circuit

Evaluate resonant circuit

Evaluate resonator circuit response


1V tuning voltage = 2.5V 4V

Evaluate resonant circuit Frequency range

Relation between unloaded Q (Qu) and Frequency range


w w

Qu and Frequency range change according to microstrip width. As Qu increase, frequency range is decrease.

Determine microstrip width


w

Qu*Frequency range is introduced as a indicator to evaluate resonant circuit performance

It shows 1.0mm is best

Insert physical layout


w

It can make layout by inserting EnsembleCircuit.

Revised circuit

Simulation with physical layout


w

Make microstrip layout and simulate resonant circuit under co-simulation

Pattern layout

Parts layout

Simulator setting

Include 0Hz

Resonant circuit simulation result

DC bias calculation

3.3 kohm

Ic is set 2.6mA

0.65V 1.5V 0.85V

3.3 kohm

330 ohm

Oscillator circuit
Parts layout

Pattern layout Oscillator circuit

Simulation result
w

After adjust resonant circuit

Output Level

Oscillation frequency

Buffer amp design


w

DC bias
3.3 kohm

3.3 kohm 330 ohm

Impedance matching
w

Adjusted circuit

TG21

S11 & S22

Simulation result with physical layout

Pattern layout

S11 & S22

Revised circuit

Final circuit

Pattern layout

Buffer amp performance

TG21

S11 & S22 S21 S11 S22 S12

Total simulation
w

Final step of VCO design


w w w w

Merge oscillator and buffer amp layout. Make schematic which include EnsembleCircuits symbol Adjust oscillation frequency Adjust other performances.

Merged layout and schematic

Merged layout

VCO schematic

Adjusted layout
Condenser move

Microstrip length shortened

Resonant microstrip length shortened

Final result
w

Oscillation frequency and output power

Final result
w

Output spectrum and load-pull characteristics

Final result
w

Output voltage and power waveform

Conclusion
w w

VCO design is showed step by step Ansoft DesignerTM is powerful tool


w

Seamless environment between circuit and electro magnetic simulator makes short time design.

You might also like