Scribd
Upload
82 views3 pages

Irrigation Division Chunar, Mirzapur: Design of Beam

This document summarizes the design of a beam for an irrigation division project. Key details include: 1) The minimum depth of the beam is based on a serviceability requirement of e/d=20 for a simply supported beam. 2) The loads on the beam include self-weight, slab weight, parapet wall weight, live/superimposed load, and a safety factor is applied to calculate the total load. 3) Calculations are shown to determine the required depth, steel reinforcement, and shear reinforcement based on the loads and strength requirements. 4) The final design parameters include a beam depth of 300mm, 3 bars of 16mm diameter longitudinal reinforcement, and 8mm diameter

Uploaded by

govind narayan Shukla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
82 views3 pages

Irrigation Division Chunar, Mirzapur: Design of Beam

This document summarizes the design of a beam for an irrigation division project. Key details include: 1) The minimum depth of the beam is based on a serviceability requirement of e/d=20 for a simply supported beam. 2) The loads on the beam include self-weight, slab weight, parapet wall weight, live/superimposed load, and a safety factor is applied to calculate the total load. 3) Calculations are shown to determine the required depth, steel reinforcement, and shear reinforcement based on the loads and strength requirements. 4) The final design parameters include a beam depth of 300mm, 3 bars of 16mm diameter longitudinal reinforcement, and 8mm diameter

Uploaded by

govind narayan Shukla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

IRRIGATION DIVISION CHUNAR, MIRZAPUR

Design of Beam

Design Contains

M2O Fe415
Xu
=0 . 479
cl

Compatation of loads

The Minimum depth of beam is base on limit state of serviceability


requirement for simply supported beam e/d = 20

For a Fe415 Fs=0.58x415= 240

Hence modification factor = 1


L 3500
= =175 mm
cl= 20 20

For Preliminary Calculation assuming table depth

D as 300 mm and width as 300 mm

Self wt of Beam = 0.3x0.3x1x25000= 2250 N/M

Wt of slab =
( 1
2
x 3 . 50 x 1. 75 ) x
0 . 15
3 . 50
x 25000=3251 .25 N /m

Wt. of Parapet wall = 1x0.15x1.20x25000=4500 N/m


Live/Super imposed load = 2000 N/m
Total Load = 12031.25
Wu = 1.5x12031.25 = 18046.875 = 18.05 KN/m
Effective length
l = 2.90+0.30=3.20 m
2 2
wa. l 18 . 05 x 3 .2
= =23 . 104
Mumax = 8 8 KN-M
= 23.104x106 N-mm
effective depth required

√ √
Mu
d= Ru .b
=
23 . 104 x 10 6
2 .761 x 300 = 167.01 mm

Providing nominal cover of 25 mm and 16mm  bars with 8 mm 


stirrups
16
D= 167+25+8+ 2 =208 mm
Keeping D as 300 mm as assumed earlier
16
Cl available = 300-25-8- 2 = 259 mm
Since of available is more than required have section will be under
reinforced
Steel Reinforcement :-
Mumax
6
xu 23 .104 x 10
0. 87 fyd(1−
Ast = cl = 0. 87 x 415 x259(1−0479)

=474.22 mm2
Providing 16mm bars
474 . 22
No. of lear = 201. 06 =2.35 3 Nos.
Providing 3 Nos. of 16 mm  bas
Seal Reinforcement :-
Critical section for shear is at a distance
d= 259 mm from the face of the support

VuD
WuL
= 2
−wl (
0. 300
2
+0 .259 )
18046 .88 x 3. 20
−18046 .88 (0. 409)
= 2

= 21494.2 N
τ v =¿=0.276 N/mm2
For Shear strength of concrete
100 x(3 x201 . 06 )
c/c P= 300 x259 = 0.78 c/c
From IS Code τ c =¿
=0.5672
Since τ c > τ v , no shear reinforcement is necessary
However as per Cobol provision nominal shear reinforcement is required
Astv 0 . 4 2 . 175 Asvfg
>
b. Sv 0 .87 fy or Sv b

Using 8mm bars Av=100.50 mm2


2 . 175 x 100.50 x 415
Sv= 300 = 300 mm
Maximum Sv least of 0.75 d or 300 mm
0.75x259=194.25 mm
Hence Providing 8mm 2 Logical stirrups @ 190 mm c/c

You might also like