Tittle

In aluminium cylinder blocks, the cylinder liners are made of

The best fuels for compression ignition engines are

During suction stroke, the inside pressure of cylinder is

Which of the following is not an automobile?
The commonly used antifreeze solution in automobiles is
A heat treated glass generally used in automobiles bursts into ________ upon cracking,
The connecting rod lower end is connected to the relevant ________ of crankshaft.
Clutch facings are usually attached to the plate by
The main cause for the change in engine oil viscosity is
The motion of the cam is transferred to the valves through
The operation of removing trapped air from the hydraulic braking system is known as
The calorific value of Diesel is about
The formula for Iso-octane is
The component in the radiator of an automobile that increases the boiling point of water is
In a square type engine
The coefficient of friction for the clutch facing is approximately
Which part of the automobile tyre is subjected to greatest flexing action?
The component in the radiator of an automobile that increases the boiling point of water is
The formula for Iso-octane is
The calorific value of Diesel is about
How many cells are used in a 12 volt car battery?
The lower cylindrical portion of the piston which improves piston cooling performance is called
The octane number of compressed natural gas (CNG) is
Bead wires are made of
The exhaust gas from petrol engine contains

It is necessary to maintain the valve clearances as they

The oil pump is driven by the
A traction control system (TCS) in automobiles controls the
A clutch is usually designed to transmit maximum torque which is
The vehicle ride will be comfortable if
The torque available at the contact between driving wheels and road is known as
Which of the following symptom is caused as a result of brake disc run out ?
What type of bearing is used for main bearings and connecting rod bearings ?
Incorrect steering axis inclination (S.A.I.) causes
The effect of having excess camber is
The function of an alternator in an automobile is to
If the air-fuel mixture in a spark ignition engine is too rich, then air-fuel ratio is about
In automobiles G.V.W. refers to
The firing order for an in-line four cylinder I.C. engine is
If the engine coolant leaks into the engine oil, then engine oil
In radial tyres
In a ventilated disc brake,
A

Aluminium

Straight chain paraffin

More than the atmospheric pressure

Motor cycle
Carbon disulphide
Sharp edged fragments
Big end
Steel rivets
Humidity
pistons
trapping
36.5 MJ/kg
C8H18
Drain plug
Geometrical shape is square
0.1
Bead
Drain plug
C8H18
36.5 MJ/kg
2
Piston crown
90
Steel
Petrol vapours

reduce the resistance to sliding that occurs

alternator shaft
vibrations on the steering wheel
80 per cent of the maximum engine torque
unsprung mass is kept minimum
clutch effort
Ineffectiveness of the brakes
What type of bearing is used for main bearin
poor recovery of the steering wheel after ma
uneven tyre wear
convert mechanical energy into electrical en
 17:1
gross vehicle wheel track
1-3-2-4
turns black
none of these
a duct directs air towards the caliper for coo
B

Ceramic

Aromatics

Less than the atmospheric pressure

Passenger car
Ethylene glycol
Small particles
Crank arm
Brass rivets
Temperature
rocker arms
tapping
42.5 MJ/kg
C7H17
Water jacket
Diameter and length of piston are same
0.4
Side wall
Water jacket
C7H17
38.5 MJ/kg
4
Connecting rod
100
Copper
Water vapours

allow for lengthening of the valves owing to the heat of combustion

camshaft
engine power during acceleration
150 per cent of the maximum engine torque
sprang mass is kept minimum
none of these
Judder during braking
Needle roller bearing
tendency to assume toe-out orientation
excessive steering alignment torque
partly convert engine power into electric power
 10:01
gross vehicle wheel base
1-2-3-4
becomes foamy
inner tubes are always used
caliper is covered with cooling fins
C

Brass

Branched chain paraffin

Equal to the atmospheric pressure

Aeroplane
Ammonium chloride
Large particles
Journal
Aluminium screws
Vibration
camshaft pulley
bleeding
38.5 MJ/kg
CX7H17
Vacuum valve
Two cylinders are placed horizontal and two vertical
0.8
Shoulder
Vacuum valve
C6H18
42.5 MJ/kg
6
Piston pin boss
110
Aluminium
Carbon monoxide

increase the speed at which the valves move up and down

crankshaft directly
torque that is transmitted by the tyres to the road surface
none of these
vehicle mass is kept minimum
tractive effort
Rapid wearing of the brake pads
Plain bearings
generation of a braking effect at tight corners
hard steering
supply electric power
 15:01
gross vehicle weight
1-2-4-3
appears milky
all plies run parallel to one another and vertical to tyre bead
disc contains radial vanes between its rubbing surfaces for optimum cooling performance
D

Cast iron

Naphthalene

None of these
Truck
Freon-12
None of these
Small end
Steel screws
Contamination
valve stems
cleaning
45.5 MJ/kg
C7H18
Pressure cap
Stroke length and cylinder bore are same
1.2
Tread
Pressure cap
C7H18
42.5 MJ/kg
8
Piston skirt
120
Correct Answer
All of these

make the crankshaft turn smoothly

crankshaft via drive belt
stopping distance in case of emergency
equal to the maximum engine torque
all of these
brake effort
Localized wearing of the brake pads
Ballbearings
the vehicle to pull to the side of lesser inclination
too much traction
continually recharge the battery
 13:01
gross vehicle width
1-3-4-2
none of these
one ply layer runs diagonally one way and another layer runs diagonally the other way
disc contains many small holes for optimum cooling performance
Right Answer

Cast iron

Naphthalene

Less than the atmospheric pressure

Aeroplane
Ethylene glycol
Small particles
Journal
Brass rivets
Temperature
rocker arms
bleeding
38.5 MJ/kg
C8H18
Pressure cap
Stroke length and cylinder bore are same
0.4
Side wall
Pressure cap
C8H18
42.5 MJ/kg
6
Piston skirt
120
Steel
All of these

allow for lengthening of the valves owing to the heat of combustion

crankshaft directly
torque that is transmitted by the tyres to the road surface
150 per cent of the maximum engine torque
unsprung mass is kept minimum
tractive effort
Judder during braking
Plain bearings
poor recovery of the steering wheel after making a turn
uneven tyre wear
continually recharge the battery
 10:01
gross vehicle weight
1-3-4-2
appears milky
all plies run parallel to one another and vertical to tyre bead
disc contains radial vanes between its rubbing surfaces for optimum cooling performance