Data Sheet for Manual Simplex Strainer TOTAL 4 PAGE

● PROJECT CODE: B70170EA Purpose

● PROJECT NAME: PULAU INDAH COMBINED CYCLE POWER PLANT □ For Information

● OWNER: PULAU INDAH POWER PLANT SDN BHD

□ For Approval

●EQUIPMENT NAME : INTAKE FACILITY

■ For Construction
● DOCUMENT NUMBER : 0-WD511-VM460-00003
□ For ( )
● TITLE: DATA SHEET FOR MANUAL SIMPLEX STRAINER

0 Dec 21, 2021 J.H.Cho D.J.Kim Y.G.Kim For Construction H.J.Joo H.K.Kim J.H.Kim

PREPARED REVIEWED APPROVED CHECKED REVIEWED APPROVED

Rev.
No. DATE DESCRIPTION
ECOSET POSCO E&C
OWNER

PULAU INDAH POWER PLANT SDN BHD

Contractor (BUYER)

Sub-Contractor (Seller)
SEQUENCE REVISION

- 0
 REV.NO. DATA BY APP'D
0 2021.12.15 Y.S.Kim S.H.Han
SIMPLEX BASKET STRAINER
DATA SHEET
1 PROJECT PULAU INDAH COMBINED CYCLE POWER PLANT SHEET 1 OF 1
2 CLIENT LOCATION Pulau Indah, Malaysia
3 JOB NO. - ITEM NO. -
4 SERVICE SIMPLEX BASKET STRAINER NO. OF REQ'D WORKING: 1 S-BY 1 TOTAL 2
5 DESIGN CONDITIONS SCREEN DATA ACCESSORIES
6 CODE ASME SEC. VIII DIV.1 '2019 ED. Stamp req'd □ YES ■ NO Model No. BS-02 Hinge YES
7 Fluid name SEA WATER Ragulation DOSH Q'TY 1 Vent Valve NO
8 SHELL Filtration Area (㎡) 0.2297 Drain Valve NO
9 Operation press. 3 bar g Dimension (mm) ø150 x 450L Anchor Bolt YES
10 Operation temp. 28.9 ~ 32 ℃ Material 316L SS Fireproofing NO
11 Design press. 5.5 bar g Filtration Rating (㎛) 12 MESH Insulation NO
12 Design temp. 50 ℃ Filtration Efficiency (%) 98 Wind Velocity As for Spec.
13 Radiograph (S/H) SPOT / FULL Type Cleanable Seismic As for Spec.
14 Joint Eff. (S/H) 0.85 / 1 Manufacturer KHE Surface Prep. SEE NOTE
15 Corr. Allow. 0 mm *NOTE
16 Hydro. Test By code & regulation bar g 1. Surface Prep. : Acid Picking
3
17 Flow Rate 120 m /hr
18 Pressure Drop CLEAN : 0.0221 / DIRTY (50%) :0.0259 bar
19 MATERIALS SKETCH
20 Item Material Remarks
21 Shell / Head SA312-TP316L
22 Shell Flange SA182-F316L
23 Nozzle Flange SA182-F316L
24 Nozzle Pipe SA312-TP316L
25 Shell Bolt/Nut SA193-B8/SA194-8
26 Internals 316L SS
27 Support Legs 304 SS
28 Clip / Sup't 304 SS
29 Gasket NBR
30 Name Plate/Bracket 304 S.S/SA240-304
31 NOZZLE SCHEDULE
32 Mark Size No. Sch. Rat. Type Description
33 N1 6" 1 10S 150# WN.RF INLET
34 N2 6" 1 10S 150# WN.RF OUTLET
35 N3 1" 1 - 150# LWN.RF VENT
36 N4 1" 1 - 150# LWN.RF DRAIN
37
38
39
40
41
42
43
44
45
46
47 REMARKS
48
49
50
51
52
53
54
55
 PRESSURE DROP CALCULATION SHEET 1 OF 2

PROJECT PULAU INDAH COMBINED CYCLE POWER PLANT

CLIENT -
CALCULATION FOR OPENING AREA
ITEM NAME SIMPLEX BASKET STRAINER 1. PERFORATED PLATE. (60° ZIG ZAG)
d : PORE DIAMETER = 8.0 mm
DESIGN CONDITION P : PITCH = 10 mm
FLUID NAME : SEA WATER dp : POROUS RATIO
DESIGN PRESSURE : 5.5 bar g
DESIGN TEMPERATURE : 50 ℃ dp= 0.91 x (d / P)²
DENSITY (ρ) : 1025 kg/㎥ = 0.5824
FLOW RATE (Qv) : 120.00 ㎥/hr
VISCOSITY (μ) : 1 CP
NOZZLE SIZE & SCH. : DN150 10S
NOZZLE INSIDE DIA. : 161.5 mm
NOZZLE SECTION AREA(An) : 0.0205 m2 2. SCREEN (PLAIN WEAVE)
STRAINER TYPE : B TYPE n : MESH = 12
( EX.: Y, T1, T2, T3 ,B ,C1 ,C2) Wd : WIRE DIAMETER = 0.460 mm
REQUIRED PRESSURE DROP (ΔPr) = 0.07 bar O : OPENING = 1.657 mm
P : PITCH
ELEMENT DATA ds: POROUS RATIO
d1 d2 L2
DIMENSION : Ø 150 x Ø0 x 450 mm

Q'TY : 1 EA P= 25.4 / n = 2.1167 mm

2
ELEMENT AREA (At) : 0.2297 m
POROUS PLATE : Ø8 x 10P x 2 t O P-W 2.12 - 0.46 = 0.6126
OPEN AREA OF PUNCH.PL. (Af) = At x dp = 0.1338 m2
ds = ( P )² = ( P )² = ( 2.12 )²
MESH OF SCREEN : 12 MESH (S.W.G.# 26 ) 3. ELEMENT OPENING AREA (Ae)
OPENING OF MESH (Ds) : 1.657 Ae = At x dp x ds = 0.23 x 0.5824 x 0.6126 = 0.0820
VOID RATIO OF SCREEN(ds) : 0.6126 4. RATIO OF OPENING AREA (R)
EFFECTIVE AREA OF WIRE SCREEN (Ae) = At x ds R = Ae / An x 100 = 0.082 / 0.0205 x 100
= 0.1407 m2 = 401 %
T-3, C-1, C-2 K=0.1
INITIAL or CLEAN Y, T-1, T-2 K=0.2
1. PRESSURE DROP OF CONTAINER (ΔPh) BUCKET TYPE K=1.5
* NOZZLE VELOCITY (Vn) = Qv / An = 1.62721 m/sec
* LOSS COEFFICENT (K) : 1.5
ΔPh = Kx(Vn2/(2xgc))xρx10-4 kg/cm2 g = 0.02077048675 bar g
2. PRESSURE DROP OF WIRE MESH SCREEN (ΔPs)
* SCREEN VELOCITY (Vs) = Qv / Ae = 0.4067 m/sec
-3 -3
* NRC = (DSx10 xVsxρ) / (dsxμx10 ) = 1127.379
* DISCHARGE COEFFICIENT (C) : 1.18 ( SEE FIGURE # 1 )
-4
ΔPs =( n )x ( 1 - ds² )x ( Vs² )x ρ x 10 bar g = 0.0010295296693
C² ds² 2 x gc bar g
3. PRESSURE DROP OF PUNCHING PLATE (ΔPp)
* WEIGHT FLOW RATE (Qw) = Qv x ρ = 34.1667 kg/sec
* t / Dp = 0.25
* NRC = (Qwxdx10-3) / (Afxμx10-3) = 2042.939
0.1
* C x (Pt / d) = 0.794 ( SEE FIGURE # 2 )
* ORIFICE COEFFICIENT (C) : 0.7765
-4
ΔPp = [ Qw²{1 - (Af / At)²} ] x 10 bar g = 0.00035577 bar g
2 x gc x ρ x C²x Af²

** INITIAL PRESSURE DROP (TOTAL) **

ΔPi = ΔPh + ΔPs + ΔPp = 0.0221557860006 bar g

KYUNG HAN ENGINEERING CORP.

 PRESSURE DROP CALCULATION SHEET 2 OF 2

PROJECT PULAU INDAH COMBINED CYCLE POWER PLANT

CLIENT -
CALCULATION FOR OPENING AREA
ITEM NAME SIMPLEX BASKET STRAINER 1. PERFORATED PLATE. (60° ZIG ZAG)
d : PORE DIAMETER = 8.0 mm
DESIGN CONDITION P : PITCH = 10 mm
FLUID NAME : SEA WATER dp : POROUS RATIO
DESIGN PRESSURE : 5.5 bar g
DESIGN TEMPERATURE : 50 ℃ dp= 0.91 x (d / P)²
DENSITY (ρ) : 1025 kg/㎥ = 0.5824
FLOW RATE (Qv) : 120.00 ㎥/hr
VISCOSITY (μ) : 1 CP
NOZZLE SIZE & SCH. : DN150 10S
NOZZLE INSIDE DIA. : 161.5 mm
NOZZLE SECTION AREA(An) : 0.0205 m2 2. SCREEN (PLAIN WEAVE)
STRAINER TYPE : B TYPE n : MESH = 12
( EX.: Y, T1, T2, T3 ,B ,C1 ,C2) Wd : WIRE DIAMETER = 0.460 mm
REQUIRED PRESSURE DROP (ΔPr) = 0.1 bar O : OPENING = 1.657 mm
P : PITCH
ELEMENT DATA ds: POROUS RATIO
d1 d2 L2
DIMENSION : Ø 150 x Ø0 x 450 mm

Q'TY : 1 EA P= 25.4 / n = 2.1167 mm

2
ELEMENT AREA (At) : ( 50% CLOGGED ) 0.1149 m
POROUS PLATE : Ø8 x 10P x 2 t O P-W 2.12 - 0.46 = 0.6126
OPEN AREA OF PUNCH.PL. (Af) = At x dp = 0.0669 m2
ds = ( P )² =(
P )² = ( 2.12 )²
MESH OF SCREEN : 12 MESH (S.W.G.# 26 ) 3. ELEMENT OPENING AREA (Ae)
OPENING OF MESH (Ds) : 1.657 Ae = At x dp x ds = 0.115 x 0.5824 x 0.6126 = 0.0410
VOID RATIO OF SCREEN(ds) : 0.6126 4. RATIO OF OPENING AREA (R)
EFFECTIVE AREA OF WIRE SCREEN (Ae) = At x ds R = Ae / An x 100 = 0.041 / 0.0205 x 100
= 0.0704 m2 = 201 %
T-3, C-1, C-2 K=0.1
50% BLOCKED Y, T-1, T-2 K=0.2
1. PRESSURE DROP OF CONTAINER (ΔPh) BUCKET TYPE K=1.5
* NOZZLE VELOCITY (Vn) = Qv / An = 1.62721 m/sec
* LOSS COEFFICENT (K) : 1.5
ΔPh = Kx(Vn2/(2xgc))xρx10-4 kg/cm2 g = 0.020770487 bar g
2. PRESSURE DROP OF WIRE MESH SCREEN (ΔPs)
* SCREEN VELOCITY (Vs) = Qv / Ae = 0.8134 m/sec
-3 -3
* NRC = (DSx10 xVsxρ) / (dsxμx10 ) = 2254.758
* DISCHARGE COEFFICIENT (C) : 1.26 ( SEE FIGURE # 1 )
-4
ΔPs =( n )x ( 1 - ds² )x ( Vs² )x ρ x 10 bar g = 0.0036005 bar g
C² ds² 2 x gc

3. PRESSURE DROP OF PUNCHING PLATE (ΔPp)

* WEIGHT FLOW RATE (Qw) = Qv x ρ = 34.1667 kg/sec
* t / Dp = 0.25
* NRC = (Qwxdx10-3) / (Afxμx10-3) = 4085.879
0.1
* C x (Pt / d) = 0.75 ( SEE FIGURE # 2 )
* ORIFICE COEFFICIENT (C) : 0.7334
-4
ΔPp = [ Qw²{1 - (Af / At)²} ] x 10 bar g = 0.001594951 bar g
2 x gc x ρ x C²x Af²

** INITIAL PRESSURE DROP (TOTAL) **

ΔPi = ΔPh + ΔPs + ΔPp = 0.0259659079120 bar g

KYUNG HAN ENGINEERING CORP.