4170C

Operating
Specification
Mobile Mining Crusher

Working Ranges Capacity

Shovel Dumping Height 9.5 m 31 ft. Optimum Loading Shovel Size P&H 4100 Series
(Dipper Door Open)
Design Capacity
Crusher Discharge Height Nominal 7.3K-9K MT/h 8K-10KST/h
Max 11.5 m 38 ft. Maximum throughput 10K MT/h 11KST/h
Min Application dependent
Maximum feed size 2.4 m3 7.9 ft3
Floor Level Radius 41 m 135 ft
Product Size 400 mm 46 in
Swing radius
Tail (Hopper side) 22 m 72 ft Hopper Capacity
Head (Discharge side) 51 m 167 ft Payload 275MT 303ST

Volumetric Capacity 170m3 222yd3

 8
1 6
4
2
7
5

1 Electrical Control 3 Propel 6 Optional Hydraulic Boom & Breaker 8 Twin Roll Crusher
‡ Centurion Supervisory Controller provides direct integrated ‡ Two rugged planetary gear cases of proven design independently ‡ Breaker provided 30 foot boom and 170° swing angle to break ‡ Has a modular design with an easy access for maintenances
comunication with motor drives giving precise motor control and transmit torque to the drive sprockets, producing the tractive material both on the apron feeder and in the sizer feed chute.
fast cycle times. Real-time multi-tasking capability allows for optimal effort required for fast, efficient propel and positioning operations ‡ Wheel mounted roll out for quick shaft/teeth replacements
machine logic sequencing, monitoring and control. contributing to greater digging time ‡ The hammer is a 5000 foot-pounds of energy and 5.3 inch wedge
‡ Design accommodates properties of the material i.e. abrasiveness,
tool. It operates at up to 2755 psi and 52 gpm. A 100HP hydraulic
‡ Centurion I/O System uses ‘Profibus’ communication protocol ‡ P&H DELTA Drive low tension sprocket drive system with heavy duty stickiness
power unit is provided.
for seamless integration of all shovel subsystems and future cast crawler shoes ‡ Equipped with dual VFD control reversible drives
expandability. Low-voltage 24V DC I/O drop points feature open and
short circuit detection for improved diagnostics and troubleshooting. ‡ Spring set air release disc brakes - one per motor Capacity
Nominal 9MT/h 10KST/h
Maximum 10.8MT/h 12KST/h

4 Apron Feeder Finished product size

‡ Heavy duty and able to withstand an impact of material dumped

7 Electro Magnet Nominal
Maximum
360mm
400mm
14 in
16 in
2 Hopper directly by the EMS ‡ This magnet is capable of picking up dipper teeth and steel liner
material off the discharge conveyor belt. The desigh will allow the Roll centre distance 1570mm 62 in
‡ Equipped with dual drive variable speed control
operator to move it over an open area and drop the tramp iron.
‡ Combine consistent productivity with high durability and ‡ D9 tractor-type chain and rollers Teeth pattern Application dependent
maintainability ‡ Able to be lifted completely with a partially full Hoper for propelling
Method of securing tooth segment Quick disconnect
‡ Configured to the mine specific conditions and capacity requirements Width between skirts 2.9 m 114in.
‡ Specific wear packages can be cooperatively specified Wear material on tooth segment Application dependent
Drive type Electric
‡ Accepts Run Of the Mine material that is directly dumped by Shovel Wear material in sizing chamber Application dependent
‡ Walls are at the angle that material unrestrictedly funneled to the
apron plate feeder Power Requirements
‡ Shaped so that the shovel can approached at 270° for loading 5 Slewing & Luffing Discharge Conveyor Supply Voltage* 7200V or 13800V 6000 6600 or 11000V
Maximum height of hopper 7.9 m 26 ft 3 Phase, 60 Hz 3 Phase, 50 Hz.
Length up to 39 m up to 128 ft
Supply Transformer (Minimum) 5000 kVA
Volumetric Capacity Minimum Short Circuit VA Available 25 MVA
Belt speed up to 2.4m/s up to 467ft/min
Struck 170m3 222yd3 *Voltage per customer requirements
Heaped
Belt width 2400mm 96 in
TRANSFORMER
Nominal Capacity 275mT 303sT
Inclination Up to 14 degrees / Down 5 degrees Auxiliarie Transformer 450 kVA
Control/Lighting Supply Winding 50 kVA
Dipper Loads 3
Slewing Angle .+/-55° from within line of plant Note: Transformer capacities may vary depending on options
G

A Overall Dimensions
A Overall Width 21.4 m 70 ft. 0 in.
B Overall Length 72.2 m 237 ft. 0 in.
C Overall Height 17.2 m 56 ft. 0 in.
D Width of Crawler Shoes 3.5 m 11 ft. 6 in.

C
E Overall Width of Crawlers 12.8 m 42 ft. 0 in.
F Overall Length of Crawlers 12.8 m 42 ft. 0 in.
G Hopper Height 7.92 m 26 ft. 0 in.

Features And Customization

D
E
The Mobile Sizer is built with several features to enhance safety,
reliability, and productivity over the lifecycle of the operation.
‡ Automatic Lubrication and Compressed Air Systems with
advanced diagnostic and control
‡ Temperature Monitoring System for motors and bearings
‡ +RXVH3UHVVXUL]DWLRQ6\VWHPWRSURYLGH¿OWHUHGDLUIRUFRROLQJ
and dust suppression
‡ Auto Swing to hopper
Ground Pressure & Weight ‡ Video monitoring
Machine weight 1920 T 4.25M lb ‡ Collision avoidance
‡ Remote Health Monitoring
Crawler Width 3505mm 138 in 7KH0RELOH6L]HUFDQEHFXVWRPL]HGIRUORFDODQGPLQHVLWHVSHFL¿F
conditions in the following areas:
Crawler Bearing Area 62.56m 2
96,967in 2
‡ Control Maintenance Room
Crawler Ground Preasure ‡ Climate Control
Empty Hopper 27419.71kg/m2 39psi ‡ Cold Weather Equipment
Full Hopper 29528.92kg/m3 42psi ‡ Technology and Software
‡ Electrical and Mechanical Systems
‡ Maintenance Systems

Box 310 t
Milwaukee,Wisconsin 53201 USA

www.phmining.com Phone: (414) 671-4400 t Fax: (414) 671-7306 www.minepro.com

NOTE: All designs, specifications and components of equipment described above are subject to change at manufacturer’s sole discretion at any time
without advance notice. Data published herein is informational in nature and shall not be construed to warrant suitability of machine for any particular
purpose as performance may vary with conditions encountered. The only warranty applicable is our standard written warranty for this machine.
P&H and P&H MinePro Services are trademarks of Joy Global Inc. or one of its affiliates. © 2009 P&H Mining Equipment Inc. All rights reserved.

XS-4788 PDF-709