DRIVER INFORMATION & MULTIMEDIA

SECTION
WARNING CHIME SYSTEM
WCS B

E
CONTENTS
BASIC INSPECTION .................................... 3 COMMON ITEM .........................................................12 F
COMMON ITEM : CONSULT-III Function (BCM -
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 COMMON ITEM) .....................................................12
Work Flow ................................................................. 3 G
BUZZER .....................................................................12
FUNCTION DIAGNOSIS ............................... 4 BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ..........................................................................12
WARNING CHIME SYSTEM ............................... 4 H
COMPONENT DIAGNOSIS ......................... 14
WARNING CHIME SYSTEM ....................................... 4
WARNING CHIME SYSTEM : System Diagram ...... 4 POWER SUPPLY AND GROUND CIRCUIT .... 14
WARNING CHIME SYSTEM : System Description I
...... 4 COMBINATION METER ............................................14
WARNING CHIME SYSTEM : Component Parts COMBINATION METER : Diagnosis Procedure ....14
Location ..................................................................... 5 J
BCM (BODY CONTROL MODULE) ..........................14
WARNING CHIME SYSTEM : Component De- BCM (BODY CONTROL MODULE) : Diagnosis
scription ..................................................................... 5 Procedure ................................................................14
LIGHT REMINDER WARNING CHIME ....................... 5 K
METER BUZZER CIRCUIT ............................... 16
LIGHT REMINDER WARNING CHIME : System
Description ...............................................................16
Diagram ..................................................................... 5
Component Function Check ....................................16 L
LIGHT REMINDER WARNING CHIME : System
Diagnosis Procedure ...............................................16
Description ................................................................ 6
LIGHT REMINDER WARNING CHIME : Compo- PARKING BRAKE SWITCH SIGNAL CIR-
nent Parts Location ................................................... 6 CUIT .................................................................. 17 M
LIGHT REMINDER WARNING CHIME : Compo- Description ...............................................................17
nent Description ........................................................ 6 Diagnosis Procedure ...............................................17
PARKING BRAKE RELEASE WARNING CHIME ...... 6 Component Inspection .............................................17 WCS
PARKING BRAKE RELEASE WARNING CHIME WARNING CHIME SYSTEM ............................. 18
: System Diagram ...................................................... 7
Wiring Diagram - WARNING CHIME (LHD MOD-
PARKING BRAKE RELEASE WARNING CHIME O
ELS) - ......................................................................18
: System Description ................................................. 7
Wiring Diagram - WARNING CHIME (RHD MOD-
PARKING BRAKE RELEASE WARNING CHIME
ELS) - ......................................................................21
: Component Parts Location ...................................... 7
P
PARKING BRAKE RELEASE WARNING CHIME ECU DIAGNOSIS ......................................... 24
: Component Description ........................................... 8
COMBINATION METER ................................... 24
DIAGNOSIS SYSTEM (METER) ......................... 9 Reference Value ......................................................24
CONSULT-III Function (METER/M&A) ..................... 9 Wiring Diagram - METER (LHD MODELS) - ...........29
Wiring Diagram - METER (RHD MODELS) - ..........38
DIAGNOSIS SYSTEM (BCM) ............................12
Fail Safe ..................................................................46

WCS-1
 DTC Index .............................................................. 47 Diagnosis Procedure ............................................... 74

BCM (BODY CONTROL MODULE) .................. 48 THE PARKING BRAKE RELEASE WARNING
Reference Value ..................................................... 48 CONTINUES SOUNDING, OR DOES NOT
Wiring Diagram - BCM - ......................................... 65 SOUND .............................................................. 75
Fail Safe ................................................................. 71 Description .............................................................. 75
DTC Inspection Priority Chart .............................. 72 Diagnosis Procedure ............................................... 75
DTC Index .............................................................. 73
PRECAUTION ............................................ 76
SYMPTOM DIAGNOSIS ............................. 74
PRECAUTIONS ................................................. 76
THE LIGHT REMINDER WARNING DOES Precaution for Supplemental Restraint System
NOT SOUND ...................................................... 74 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
Description .............................................................. 74 SIONER" ................................................................. 76

WCS-2
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001080318
B

DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM C
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
D
>> GO TO 2.
2.CHECK SYMPTOM E
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
F
>> GO TO 3.
3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS G
Connect CONSULT-III and perform self-diagnosis. Refer to WCS-9, "CONSULT-III Function (METER/M&A)".
Are self-diagnosis results normal?
YES >> GO TO 4. H
NO >> Repair or replace the malfunctioning parts and go to 5.
4.NARROW DOWN THE MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
I
Perform symptom diagnosis and repair or replace the identified malfunctioning parts.

>> GO TO 5. J
5.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally? K
YES >> INSPECTION END
NO >> GO TO 1.
L

WCS

WCS-3
 WARNING CHIME SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Diagram INFOID:0000000001080319

JSNIA0441GB

WARNING CHIME SYSTEM : System Description INFOID:0000000001080320

• Combination meter judges the necessity of parking brake warning according to vehicle speed signal and
parking brake switch signal.
• BCM judges the necessity of buzzer output according to signals from each switch, and transmits signal to
combination meter.
NOTE:
• Intelligent key warning is judged by intelligent key unit.
• Seat belt reminder warning is judged by front seat belt warning unit. Seat belt reminder warning buzzer is
integrated in the front seat belt warning unit.
COMBINATION METER
• The buzzer (1) for the warning chime system is integrated in the
combination meter.
• Combination meter sounds warning buzzer in the following condi-
tions.
- When it receives buzzer output signal from BCM with CAN com-
munication.
- When it judges the necessity of buzzer output according to vehicle
speed signal received from ABS actuator and electric unit (control
unit) with CAN communication and parking brake switch signal
received from parking brake switch.
JSNIA0319ZZ

BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
BCM warning function list
Warning functions Signal name
• Ignition switch signal
Light reminder warning chime • Lighting switch position signal
• Front door switch signal (driver side)

WCS-4
 WARNING CHIME SYSTEM
< FUNCTION DIAGNOSIS >
WARNING CHIME SYSTEM : Component Parts Location INFOID:0000000001080321

JSNIA0529ZZ F

Combination switch
1. 2. Front door switch (driver side) 3. Parking brake switch
(Lighting switch)
G
4. BCM

WARNING CHIME SYSTEM : Component Description INFOID:0000000001080322

H

Unit Description
• Receives the buzzer output signal from BCM with the CAN communication line and sounds the I
buzzer.
Combination meter • Judges the remaining parking brake according to the vehicle speed signal received from the ABS
actuator and electric unit (control unit) via CAN communication and the parking brake switch sig-
nal from parking brake switch to sound the warning buzzer. J
Transmits signals received from each unit to the combination meter with the CAN communication
BCM
line.
K
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter with the CAN communication line.
(control unit)
Combination switch
Transmits the lighting switch position signal to BCM. L
(Lighting switch)
Front door switch (driver side) Transmits the door switch signal to BCM.
Parking brake switch Refer to WCS-17, "Description".
M
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000001080323
WCS

JSNIA0460GB

WCS-5
 WARNING CHIME SYSTEM
< FUNCTION DIAGNOSIS >
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000001080324

DESCRIPTION
With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1ST or 2ND position, the
light reminder warning chime will sound.
• BCM detects ignition switch in OFF or ACC position, front door switch (driver side) ON, and lighting switch in
1ST or 2ND position. And then transmits buzzer output signal (light reminder warning chime) to combination
meter with CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
• Lighting switch is at 1ST or 2ND position
• Ignition switch is at OFF or ACC
• Front door switch (driver side) is ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF
• Ignition switch ON
• Front door switch (driver side) OFF
LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000001297236

JSNIA0529ZZ

Combination switch
1. 2. Front door switch (driver side) 3. Parking brake switch
(Lighting switch)
4. BCM

LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000001080326

Unit Description
Combination meter Receives a buzzer output signal from the BCM and sounds the buzzer.
Judges the light reminder warning conditions from the signals provided by various switches and
BCM
transmits a buzzer output signal to the combination meter via CAN communication line if necessary.
Combination switch
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Front door switch (driver side) Transmits the door switch signal to BCM.

PARKING BRAKE RELEASE WARNING CHIME

WCS-6
 WARNING CHIME SYSTEM
< FUNCTION DIAGNOSIS >
PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000001080331

JSNIA0299GB

D
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000001080332

E
DESCRIPTION
Parking brake release warning chime judges the remaining parking brake according to the vehicle speed sig-
nal received from the ABS actuator and electric unit (control unit) via CAN communication and the parking
brake switch signal from parking brake switch to sound the warning buzzer. F
WARNING OPERATION CONDITIONS
If any of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or higher G
• Parking brake switch ON
WARNING CANCEL CONDITIONS
H
Warning is canceled if any of the following conditions is fulfilled.
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
I
PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location
INFOID:0000000001297237

WCS

JSNIA0529ZZ
O
Combination switch
1. 2. Front door switch (driver side) 3. Parking brake switch
(Lighting switch)
4. BCM P

WCS-7
 WARNING CHIME SYSTEM
< FUNCTION DIAGNOSIS >
PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000001080334

Unit Description
Judges the remaining parking brake according to the vehicle speed signal received from the ABS
Combination meter actuator and electric unit (control unit) via CAN communication and the parking brake switch signal
from parking brake switch and sounds the warning buzzer.
ABS actuator and electric unit
Transmits the vehicle speed signal to the combination meter via CAN communication.
(control unit)
Parking brake switch Refer to WCS-17, "Description".

WCS-8
 DIAGNOSIS SYSTEM (METER)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (METER)
A
CONSULT-III Function (METER/M&A) INFOID:0000000001081148

CONSULT-III FUNCTION (METER/M&A) B

System Diagnosis mode Description

Self Diagnostic Result Combination meter checks the conditions and displays memorized error. C
METER/M&A
Data Monitor Displays combination meter input/output data in real time.

SELF DIAGNOSTIC RESULT D

Refer to MWI-64, "DTC Index".
DATA MONITOR
E
Display Item List
X: Applicable
MAIN
Display item [Unit]
SIGNALS
Description F

Value of vehicle speed signal received from ABS actuator and electric unit (con-
SPEED METER trol unit) with CAN communication line.
X G
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received.
Vehicle speed signal value transmitted to other units with CAN communication
SPEED OUTPUT
X
line. H
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
Odometer signal value transmitted to other units with CAN communication line. I
[km/h or mph]
Value of the engine speed signal received from ECM with CAN communication
TACHO METER line.
X J
[rpm] NOTE:
8191.875 is displayed when the malfunction signal is received.
FUEL METER
X Fuel level indicated on combination meter.
[lit.] K
Value of engine coolant temperature signal received from ECM with CAN com-
W TEMP METER munication line.
X
[°C] NOTE: L
215 is displayed when the malfunction signal is input.
ABS W/L Status of ABS warning lamp judged from ABS warning lamp signal received from
[On/Off] ABS actuator and electric unit (control unit) with CAN communication line.
M
Status of ESP indicator lamp judged from ESP OFF indicator lamp signal re-
VDC/TCS IND
ceived from ABS actuator and electric unit (control unit) with CAN communication
[On/Off]
line.
WCS
SLIP IND Status of slip indicator lamp judged from slip indicator lamp signal received from
[On/Off] ABS actuator and electric unit (control unit) with CAN communication line.
Status of brake warning lamp judged from brake warning lamp signal received
from ABS actuator and electric unit (control unit) with CAN communication line. O
BRAKE W/L NOTE:
[On/Off] Displays “Off” if the brake warning lamp is illuminated when the valve check
starts, the parking brake switch is turned ON or the brake fluid level switch is
turned ON. P
DOOR W/L Status of door warning lamp judged from door switch signal received from BCM
[On/Off] with CAN communication line.
HI -BEAM IND Status of high beam indicator lamp judged from high beam request signal re-
[On/Off] ceived from BCM with CAN communication line.
TURN IND Status of turn indicator lamp judged from turn indicator signal received from BCM
[On/Off] with CAN communication line.

WCS-9
 DIAGNOSIS SYSTEM (METER)
< FUNCTION DIAGNOSIS >
MAIN
Display item [Unit] Description
SIGNALS
FR FOG IND Status of front fog lamp indicator lamp judged from front fog light request signal
[On/Off] received from BCM with CAN communication line.
RR FOG IND Status of rear fog lamp indicator lamp judged from rear fog lamp status signal re-
[On/Off] ceived from BCM with CAN communication line.
OIL W/L Status of oil pressure warning lamp judged from oil pressure switch signal re-
[On/Off] ceived from IPDM E/R with CAN communication line.
MIL Status of malfunction indicator lamp judged from malfunctioning indicator lamp
[On/Off] signal received from ECM with CAN communication line.
GLOW IND Status of glow indicator lamp judged from glow indicator lamp signal received
[On/Off] from ECM with the CAN communication line.
CRUISE IND Status of CRUISE indicator judged from ASCD CRUISE lamp signal received
[On/Off] from ECM with CAN communication line.
SET IND Status of set indicator judged from ASCD SET indicator signal received from
[On/Off] ECM with CAN communication line.
ATC/T-AMT W/L Status of A/T check warning lamp judged from A/T CHECK indicator lamp signal
[On/Off] received from TCM with the CAN communication line.
4WD W/L Status of 4WD warning lamp judged from 4WD warning lamp signal received
[On/Off] from 4WD control unit with CAN communication line.
4WD LOCK IND Status of 4WD lock indicator judged from 4WD signal received from 4WD control
[On/Off] unit with the CAN communication line.
FUEL W/L
X Status of Low-fuel warning lamp judged from identified fuel level.
[On/Off]
KEY G/Y W/L Status of key warning lamp (G/Y) judged from key warning signal received from
[On/Off] Intelligent Key unit with CAN communication line.
KEY R W/L Status of key warning lamp (R) judged from key warning signal received from In-
[On/Off] telligent Key unit with CAN communication line.
KEY KNOB W/L Status of Key knob switch received from Intelligent Key unit with the CAN com-
[On/Off] munication line.
EPS W/L Status of EPS warning lamp judged from EPS warning lamp signal received from
[On/Off] EPS control unit with the CAN communication line.
Status of HDC warning lamp judged from HV system warning lamp signal re-
HDC W/L
ceived from ABS actuator and electric unit (control unit) with the CAN communi-
[On/Off]
cation line.
SHIFT IND
Status of shift position indicator judged from shift position signal and manual
[P/ R/ N/ D/ M1/ M2/ M3/ M4/ M5/
mode indicator signal received from TCM with CAN communication line.
M6]
O/D OFF SW
Status of O/D OFF switch.
[On/Off]
A/T S MODE SW Status of snow mode switch.
M RANGE SW
X Status of mode select switch (manual).
[On/Off]
NM RANGE SW
X Status of mode select switch (auto).
[On/Off]
AT SFT UP SW
X Status of position select switch (up).
[On/Off]
AT SFT DWN SW
X Status of position select switch (down).
[On/Off]
COMP F/B SIG A/C compressor activation condition that ECM judges according to the water tem-
[On/Off] perature and the acceleration degree.
PKB SW
Status of parking brake switch.
[On/Off]

WCS-10
 DIAGNOSIS SYSTEM (METER)
< FUNCTION DIAGNOSIS >
MAIN
Display item [Unit] Description
SIGNALS A
BRAKE OIL SW
Status of brake fluid level switch.
[On/Off]
DISTANCE B
X Value of possible driving distance calculated by combination meter.
[km]
Ambient temperature value converted from OAT sensor signal received from
OAT sensor. C
OUTSIDE TEMP NOTE:
[°C or °F] This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the OAT
sensor input value.) D
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit with CAN com-
[On/Off] munication line.
Buzzer status (in the combination meter) judged with the buzzer output signal re- E
BUZZER
X ceived from BCM via CAN communication and the warning output condition of
[On/Off]
the combination meter.
NOTE: F
Some items are not available according to vehicle specification.

WCS

WCS-11
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001307327

APPLICATION ITEM
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

Diagnosis mode Function description

ECU Identification BCM part number is displayed.
Self-Diagnostic Results Displays the diagnosis results judged by BCM. Refer to BCS-65, "DTC Index".
Data Monitor BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Work Support Changes the setting for each system function.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item

CONSULT-III Diagnosis mode

System
sub system selection item WORK SUPPORT DATA MONITOR ACTIVE TEST
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK × ×
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
— PTC HEATER*
*: This item is displayed, but is not function.
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000001080344

CONSULT-III FUNCTION (BCM – BUZZER)

WCS-12
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Test item Diagnosis mode Description A

Data Monitor Displays BCM input data in real time.
Buzzer
Active Test Operation of electrical loads can be checked by sending driving signal to them.
B
DATA MONITOR

Display item C
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged by ignition power supply input.
[On/Off]
D
KEY ON SW
Key switch status.
[On/Off]
DOOR SW -DR
Front door switch (driver side) status judged by BCM. E
[On/Off]
TAIL LAMP SW Lighting switch status judged by the lighting switch signal read with combination switch reading func-
[On/Off] tion.
F
ACTIVE TEST

Display item Description G

LIGHT WARN ALM The light reminder warning operation can be checked by operating the relevant function (On/Off).
ANTI KEY LOCK IN The anti key lock in warning operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN The key reminder warning operation can be checked by operating the relevant function (On/Off).
H

WCS

WCS-13
 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure INFOID:0000000001081149

1.CHECK FUSE
Check for blown fuses.

Terminal No. Signal name Fuses No.

1 Battery power supply 9
2 Ignition signal 3
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector terminals 1, 2 and ground.

Terminals
Ignition switch position
(+)
Combination meter (−)
OFF ON
Connector Terminal
Battery Battery
1
voltage voltage
M34 Ground
Approx. Battery
2
0V voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminals 3, 23 and ground.

Combination meter
Continuity
Connector Terminal
Ground
3
M34 Existed
23
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000001367522

1.CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not fusing.

WCS-14
 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >

Terminal No. Signal name Fuses and fusible link No. A

41 10
Battery power supply
57 J
B
4 ACC power supply 20
3 Ignition power supply 1
Is the fuse fusing? C
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2. D
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
E
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.

Terminals
F
Ignition switch position
(+)
BCM (−) G
OFF ACC ON
Connector Terminal
M67 57 Battery Battery Battery
M66 41 voltage voltage voltage H

Ground Approx. Battery Battery

4
0V voltage voltage
M65 I
Approx. Approx. Battery
3
0V 0V voltage
Is the measurement value normal?
J
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT K
Check continuity between BCM harness connector and ground.

BCM L
Continuity
Connector Terminal Ground
M67 55 Existed
M
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector. WCS

WCS-15
 METER BUZZER CIRCUIT
< COMPONENT DIAGNOSIS >
METER BUZZER CIRCUIT
Description INFOID:0000000001080347

• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000001080348

1.CHECK OPERATION OF METER BUZZER

1. Select “BUZZER” of “BCM” on CONSULT-III.
2. Perform “LIGHT WARN ALM” of “ACTIVE TEST”.
Does meter buzzer beep?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.

BUZZER
Under the condition of buzzer input : On
Except above : Off
Is the inspection result normal?
YES >> Replace combination meter.
NO >> Replace BCM. Refer to BCS-68, "Exploded View".
Diagnosis Procedure INFOID:0000000001080349

1.CHECK POWER SUPPLY AND GROUND CIRCUIT OF COMBINATION METER

Check power supply and ground circuit of combination meter. Refer to WCS-14, "COMBINATION METER :
Diagnosis Procedure".
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace malfunctioning parts.

WCS-16
 PARKING BRAKE SWITCH SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
A
Description INFOID:0000000001080355

Transmits the parking brake switch signal to the combination meter. B

Diagnosis Procedure INFOID:0000000001080356

1.CHECK COMBINATION METER INPUT SIGNAL C

1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector terminal 26 and ground.
D
26 – Ground
Parking brake ON : Approx. 0 V
Parking brake OFF : Approx. 5 V E
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2. F
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF. G
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector terminal 26 and parking brake switch
harness connector terminal 1.
H
26 – 1 : Continuity should exist.
4. Check continuity between combination meter harness connector terminal 26 and ground.
I
26 – Ground : Continuity should not exist.
Is the inspection result normal?
J
YES >> INSPECTION END
NO >> Repair harness or connector.
Component Inspection INFOID:0000000001080357 K

Refer to BRC-47, "Component Inspection".

L

WCS

WCS-17
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >
WARNING CHIME SYSTEM
Wiring Diagram - WARNING CHIME (LHD MODELS) - INFOID:0000000001538126

JCNWA0277GB

WCS-18
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >

WCS

JCNWA0278GB

WCS-19
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >

JCNWA0279GB

WCS-20
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >
Wiring Diagram - WARNING CHIME (RHD MODELS) - INFOID:0000000001538127

WCS

JCNWA0280GB
P

WCS-21
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >

JCNWA0281GB

WCS-22
 WARNING CHIME SYSTEM
< COMPONENT DIAGNOSIS >

WCS

JCNWA0282GB

WCS-23
 COMBINATION METER
< ECU DIAGNOSIS >
ECU DIAGNOSIS
COMBINATION METER
Reference Value INFOID:0000000001081150

VALUES ON THE DIAGNOSIS TOOL

Monitor Item Condition Value/Status

Equivalent to speedometer reading
SPEED METER Ignition switch NOTE:
While driving
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
Equivalent to speedometer reading
SPEED OUTPUT Ignition switch NOTE:
While driving
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
Ignition switch Equivalent to odometer reading in
ODO OUTPUT —
ON combination meter
Equivalent to tachometer reading
TACHO METER Ignition switch NOTE:
While driving
[rpm] ON 8191.875 is displayed when the mal-
function signal is received
FUEL METER Ignition switch
— Values according to fuel level
[lit] ON
Values according to engine coolant
temperature
W TEMP METER Ignition switch
— NOTE:
[°C] ON
215 is displayed when the malfunction
signal is input

Ignition switch ABS warning lamp ON On

ABS W/L
ON ABS warning lamp OFF Off

Ignition switch ESP OFF indicator lamp ON On

VDC/TCS IND
ON ESP OFF indicator lamp OFF Off

Ignition switch SLIP indicator lamp ON On

SLIP IND
ON SLIP indicator lamp OFF Off

Ignition switch Brake warning lamp ON On

BRAKE W/L
ON Brake warning lamp OFF Off

Ignition switch Door warning lamp ON On

DOOR W/L
ON Door warning lamp OFF Off

Ignition switch High beam indicator lamp ON On

HI-BEAM IND
ON High beam indicator lamp OFF Off

Ignition switch Turn signal indicator lamp ON On

TURN IND
ON Turn signal indicator lamp OFF Off

Ignition switch Front fog lamp indicator lamp ON On

FR FOG IND
ON Front fog lamp indicator lamp OFF Off

Ignition switch Rear fog lamp indicator lamp ON On

RR FOG IND
ON Rear fog lamp indicator lamp OFF Off

Ignition switch Oil pressure warning lamp ON On

OIL W/L
ON Oil pressure warning lamp OFF Off

Ignition switch Malfunction indicator lamp ON On

MIL
ON Malfunction indicator lamp OFF Off

WCS-24
 COMBINATION METER
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
Ignition switch Glow indicator lamp ON On
GLOW IND
ON Glow indicator lamp OFF Off

Ignition switch Cruise indicator lamp ON On B

CRUISE IND
ON Cruise indicator lamp OFF Off

Ignition switch SET indicator lamp ON On

SET IND
ON SET indicator lamp OFF Off C
TCM electronic control system warning
On
Ignition switch lamp ON
ATC/T-AMT W/L D
ON TCM electronic control system warning
Off
lamp OFF

Ignition switch 4WD warning lamp ON On

4WD W/L
ON
E
4WD warning lamp OFF Off

Ignition switch 4WD LOCK indicator lamp ON On

4WD LOCK IND
ON 4WD LOCK indicator lamp OFF Off F
Ignition switch Low-fuel warning lamp ON On
FUEL W/L
ON Low-fuel warning lamp OFF Off
KEY warning lamp (green/yellow) ON On
G
Ignition switch
KEY G/Y W/L
ON KEY warning lamp (green/yellow) OFF Off

Ignition switch KEY warning lamp (red) ON On H

KEY R W/L
ON KEY warning lamp (red) OFF Off

Ignition switch LOCK warning lamp ON On

KEY KNOB W/L
ON LOCK warning lamp OFF Off I

Ignition switch EPS warning lamp ON On

EPS W/L
ON EPS warning lamp OFF Off
J
Ignition switch HDC warning lamp ON On
HDC W/L
ON HDC warning lamp OFF Off
Shift position indicator P display P K
Shift position indicator R display R
Shift position indicator N display N
L
Shift position indicator D display D

Ignition switch Shift position indicator M1 display M1

SHIFT IND
ON Shift position indicator M2 display M2 M
Shift position indicator M3 display M3
Shift position indicator M4 display M4
WCS
Shift position indicator M5 display M5
Shift position indicator M6 display M6

Ignition switch O/D OFF indicator lamp ON On O

O/D OFF SW
ON O/D OFF indicator lamp OFF Off

Ignition switch Snow mode switch ON On

AT S MODE SW
ON Snow mode switch OFF Off P

Ignition switch MANUAL MODE On

M RANGE SW
ON Other than the above Off

Ignition switch MANUAL MODE Off

NM RANGE SW
ON Other than the above On

WCS-25
 COMBINATION METER
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status

Ignition switch Selector lever (+) position On

AT SFT UP SW
ON Other than the above Off

Ignition switch Selector lever (–) position On

AT SFT DWN SW
ON Other than the above Off

Ignition switch A/C compressor activation condition On

COMP F/B SIG
ON A/C compressor deactivation condition Off

Ignition switch Parking brake switch ON On

PKB SW
ON Parking brake switch OFF Off

Ignition switch Brake fluid level switch ON On

BRAKE OIL SW
ON Brake fluid level switch OFF Off
DISTANCE Ignition switch Possible driving distance calculated by
—
[km] ON combination meter
Equivalent to ambient air temperature
OUTSIDE TEMP Ignition switch NOTE:
—
[°C or °F] ON This may not match the indicated value
on the information display.

Ignition switch Low-fuel warning displayed On

FUEL LOW SIG
ON Low-fuel warning not displayed Off

Ignition switch Buzzer ON On

BUZZER
ON Buzzer OFF Off
NOTE:
Some items are not available according to vehicle specification.

TERMINAL LAYOUT

JSNIA0457ZZ

PHYSICAL VALUES

Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(G)
OFF
Ignition
2
Ground IGN signal Input switch — Battery voltage
(P)
ON
Ignition
3
Ground Ground — switch — 0V
(B)
ON

Ignition Fuel filter warning lamp ON 0V

8* Ground Fuel filter sensor signal Input switch
(Y) Fuel filter warning lamp
ON 12 V
OFF

WCS-26
 COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output

Ignition O/D OFF switch pressed 0V B

9
Ground O/D OFF switch signal Input switch O/D OFF switch not
(P) 12 V
ON pressed
Press the steering switch C
Ignition 0V
11 Steering switch (trip com- (trip computer)
Ground Input switch
(W) puter) signal
ON Other than the above 5V
D
Air bag warning lamp
Ignition 4V
15 ON
Ground Air bag signal Input switch
(GR) Air bag warning lamp
ON 0V
OFF E

F
Ignition
19
Ground OAT sensor signal Input switch —
(BR)
ON
G
JSNIA0014GB

Ignition
20
Ground OAT sensor ground — switch — 0V
H
(R)
ON
21
— CAN-H — — — —
(L) I
22
— CAN-L — — — —
(P)
Ignition J
23
Ground Ground — switch — 0V
(B)
ON

24 Fuel level sensor signal

Ignition K
Ground — switch — 0V
(B) ground
ON
Ignition Charge warning lamp ON 0V L
25
Ground Alternator signal Input switch
(BR) Charge warning lamp OFF 12 V
ON
Ignition Parking brake ON 0V
26 M
Ground Parking brake switch signal Input switch
(GR) Parking brake OFF 5V
ON

Ignition Brake fluid level is normal 5V

27 Brake fluid level switch sig- WCS
Ground Input switch Brake fluid level is less than
(LG) nal 0V
ON low level
Ignition Security warning lamp ON 0V
28 O
Ground Security signal Input switch
(B) Security warning lamp OFF 12 V
ON

WCS-27
 COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition
31 Vehicle speed signal Vehicle speed is approxi-
Ground Output switch
(V) (8 pulse) mately 40 km/h (25 MPH)
ON

JSNIA0012GB

Refer to MWI-33, "Component

Inspection (QR25DE Engine
Models)" or MWI-34, "Compo-
nent Inspection (Except
Ignition
32 QR25DE Engine Models)".
Ground Oil level sensor signal Input switch —
(L) NOTE:
ON
The measurement cannot be
performed because the signal is
input for a moment with the igni-
tion switch ON.
Ignition
33 Oil level sensor signal
Ground — switch — 0V
(O) ground
ON

Ignition
34
Ground Fuel level sensor signal Input switch —
(G)
ON

JSNIA0423GB

Ignition Manual mode 12 V

37
Ground Not manual mode signal Input switch
(Y) Other than the above 0V
ON
Ignition Selector lever (–) position 0V
38 Manual mode shift down
Ground Input switch
(O) signal Other than the above 12 V
ON
Ignition Selector lever (+) position 0V
39 Manual mode shift up sig-
Ground Input switch
(V) nal Other than the above 12 V
ON
Ignition Manual mode 0V
40
Ground Manual mode signal Input switch
(LG) Other than the above 12 V
ON
*: LHD models

WCS-28
 COMBINATION METER
< ECU DIAGNOSIS >
Wiring Diagram - METER (LHD MODELS) - INFOID:0000000001541678

WCS

JCNWA0259GB
P

WCS-29
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0260GB

WCS-30
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0261GB

WCS-31
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0262GB

WCS-32
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0263GB

WCS-33
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0264GB

WCS-34
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0265GB

WCS-35
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0266GB

WCS-36
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0267GB

WCS-37
 COMBINATION METER
< ECU DIAGNOSIS >
Wiring Diagram - METER (RHD MODELS) - INFOID:0000000001541679

JCNWA0268GB

WCS-38
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0269GB

WCS-39
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0270GB

WCS-40
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0271GB

WCS-41
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0272GB

WCS-42
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0273GB

WCS-43
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0274GB

WCS-44
 COMBINATION METER
< ECU DIAGNOSIS >

WCS

JCNWA0275GB

WCS-45
 COMBINATION METER
< ECU DIAGNOSIS >

JCNWA0276GB

Fail Safe INFOID:0000000001081152

The combination meter activates the fail-safe control if the CAN communication lines between each unit are
malfunctioning.

WCS-46
 COMBINATION METER
< ECU DIAGNOSIS >

Function Specifications A
Speedometer
Reset to zero by suspending communication.
Tachometer
Meter illumination control Change to nighttime mode.
B

Buzzer Turned off by suspending communication.

ABS warning lamp C
Brake warning lamp
EPS OFF indicator lamp Turned on by suspending communication.
ESP OFF indicator lamp D
SLIP indicator lamp
4WD warning lamp
E
SPORT indicator lamp
4WD indicator lamp
4WD LOCK indicator lamp F
Oil pressure warning lamp
Door warning lamp
Warning lamp/indicator G
Malfunction indicator lamp
lamp
CRUISE indicator lamp
SET indicator lamp H
Front fog lamp indicator lamp Turned off by suspending communication.
Rear fog lamp indicator lamp
I
Glow indicator lamp
DPF warning lamp
HDC indicator lamp J
KEY R/G warning lamp
KEY LOCK warning lamp
High beam indicator lamp K
Turn signal indicator lamp

DTC Index INFOID:0000000001081153

L

Display contents of CONSULT-III Time Diagnostic item is detected when ... Refer to M
CAN COMM CIRCUIT Combination meter is not transmitting or receiving CAN
CRNT, 1 - 39 MWI-28
[U1000] communication signal for 2 seconds or more.
CONTROL UNIT (CAN) Detecting error during the initial diagnosis of CAN control- WCS
CRNT, 1 - 39 MWI-29
[U1010] ler of combination meter.
VEHICLE SPEED The abnormal vehicle speed signal is input from ABS ac-
CRNT, 1 - 39 MWI-30
[B2205] tuator and electric unit (control unit) for 2 seconds or more. O
ENGINE SPEED ECM continuously transmits abnormal engine speed sig-
CRNT, 1 - 39 MWI-31
[B2267] nals for 2 seconds or more.
WATER TEMP ECM continuously transmits abnormal engine coolant tem- P
CRNT, 1 - 39 MWI-32
[B2268] perature signals for 60 seconds or more.
OIL LEV SEN OPEN Combination meter judged that the oil level sensor signal •MWI-33
CRNT, 1 - 39
[B2321] circuit is open-circuited for 1 second or more. (QR25DE)
OIL LEV SEN SHORT Combination meter judged that the oil level sensor signal •MWI-33 (Except
CRNT, 1 - 39 QR25DE)
[B2322] circuit is short-circuited for 1 second or more.

WCS-47
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001367523

VALUES ON THE DIAGNOSIS TOOL

Monitor Item Condition Value/Status

VEHICLE SPEED While driving Equivalent to speedometer reading
Ignition switch OFF or ACC Off
IGN ON SW
Ignition switch ON On
Mechanical key is removed from key cylinder Off
KEY ON SW
Mechanical key is inserted to key cylinder On
Door lock/unlock switch does not operate Off
CDL LOCK SW
Press door lock/unlock switch to the lock side On
Door lock/unlock switch does not operate Off
CDL UNLOCK SW
Press door lock/unlock switch to the unlock side On
Driver's door closed Off
DOOR SW-DR
Driver's door opened On
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
Rear RH door closed Off
DOOR SW-RR
Rear RH door opened On
Rear LH door closed Off
DOOR SW-RL
Rear LH door opened On
Back door closed Off
BACK DOOR SW
Back door opened On
“LOCK” button of Intelligent Key or door request switch are not
Off
I-KEY LOCK pressed
“LOCK” button of Intelligent Key or door request switch are pressed On
“UNLOCK” button of Intelligent Key or door request switch are not
Off
pressed
I-KEY UNLOCK
“UNLOCK” button of Intelligent Key or door request switch are
On
pressed
Return to ignition switch to “LOCK” position Off
PUSH SW
Press ignition switch On
“LOCK” button of key fob is not pressed Off
KEYLESS LOCK
“LOCK” button of key fob is pressed On
“UNLOCK” button of key fob is not pressed Off
KEYLESS UNLOCK
“UNLOCK” button of key fob is pressed On
Ignition switch ON NOMAL
After the reception of air bag deployment signal from air bag diag-
Off
SHOCK SENSOR nosis sensor unit
During the reception of air bag deployment signal from air bag diag-
On
nosis sensor unit
Other than the following Off
UNLOCK SHOCK
During the unlock operation interlocked with air bag On

NOTE: On
UNLOCK WITH DR
The item is indicated, but not monitored Off

WCS-48
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
Vehicle speed sensing auto door lock function does not operate Off
LOCK WITH SPEED
Vehicle speed sensing auto door lock function is operating On
Ignition switch OFF Off B
ACC ON SW
Ignition switch ACC or ON On
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On C
Lighting switch OFF Off
TAIL LAMP SW
Lighting switch 1ST On
D
Turn signal switch OFF Off
TURN SIGNAL R
Turn signal switch RH On
Turn signal switch OFF Off E
TURN SIGNAL L
Turn signal switch LH On
Lighting switch OFF Off
HI BEAM SW F
Lighting switch HI On
Lighting switch OFF Off
HEAD LAMP SW 1
Lighting switch 2ND On G
Lighting switch OFF Off
HEAD LAMP SW 2
Lighting switch 2ND On
H
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Lighting switch OFF Off I
AUTO LIGHT SW
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW J
Front fog lamp switch ON On
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On
K
Engine stopped Off
ENGINE RUN
Engine running On
Light & rain sensor is in normal condition OK L
LIT-SEN FAIL
Light & rain sensor is with error NOTOK
Outside of the room is dark On
AUT LIGHT SYS M
Outside of the room is bright Off
Displays a setting time of the follow
HD LIGHT TIME — me home function set by the work
WCS
support
Ignition switch OFF or ACC Off
IGN SW CAN
Ignition switch ON On O
Front wiper switch OFF Off
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off P
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off
FR WIPER INT
Front wiper switch INT On
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On

WCS-49
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
Any position other than front wiper stop position Off
FR WIPER STOP
Front wiper stop position On
Rear wiper switch OFF Off
RR WIPER ON
Rear wiper switch ON On
Rear wiper switch OFF Off
RR WIPER INT
Rear wiper switch INT On
Rear wiper stop position Off
RR WIPER STOP
Other than rear wiper stop position On
Rear washer switch OFF Off
RR WASHER SW
Rear washer switch ON On

NOTE: Off
REVERSE SW CAN
The item is indicated, but not monitored On
When headlamp washer switch is not pressed Off
H/L WASH SW
When headlamp washer switch is pressed On
Blower fan motor switch OFF Off
FAN ON SIG
Blower fan motor switch ON (other than OFF) On
Compressor ON is not requested from auto amp.
Off
(A/C indicator OFF, blower fan motor switch OFF or etc.)
AIR COND SW
Compressor ON is requested from auto amp.
On
(A/C indicator ON and blower fan motor switch ON).
Hazard switch OFF Off
HAZARD SW
Hazard switch ON On
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On
When back door opener switch is not pressed Off
TRNK OPNR SW
When back door opener switch is pressed On
Close the hood
NOTE: Off
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood On
Auto lock function does not operate Off
AUTO RELOCK
Auto lock function is operating On
The vehicle without glass break sensor Off
GLS BREAK SEN
The vehicle with glass break sensor On
• Ignition switch OFF or ACC
Off
OIL PRESS SW • Engine running
Ignition switch ON On

WCS-50
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
A

WCS
JSMIA0031GB

PHYSICAL VALUES O
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter- P
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT-III. Refer to
BCS-28, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-9, "System
Description".

WCS-51
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

Terminal No. Description

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Just after Insert mechanical key
1 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(W) Output der
of tester should move
Just after Insert mechanical key
2 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(G) Output der
of tester should move

3 Ignition power sup- Ignition switch OFF or ACC 0V

Ground Input
(W) ply Ignition switch ON or START Battery voltage

4 Ignition switch OFF 0V

Ground ACC power supply Input
(SB) Ignition switch ON or ACC Battery voltage
Insert mechanical key into ignition key cylin-
5 Battery voltage
der
*1
(LG) Ground Key switch Input
Remove mechanical key from ignition key
(R)*2 0V
cylinder

WCS-52
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.4 V D

E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0166GB

1.3 V
G

6 Combination switch Combination Lighting switch 2ND

H
Ground Input
(L) INPUT 3 switch (Wiper intermittent dial 4)

JPMIA0167GB
I
1.3 V

Rear washer switch ON

K

JPMIA0169GB

1.3 V L

Any of the condition below M

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 WCS
JPMIA0196GB

1.3 V
O

WCS-53
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.4 V

Lighting switch 1ST

(Wiper intermittent dial 4)

JPMIA0166GB

1.3 V

7 Combination switch Combination Lighting switch AUTO

Ground Input
(GR) INPUT 4 switch (Wiper intermittent dial 4)

JPMIA0168GB

1.3 V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 6

JPMIA0169GB

1.3 V

Rear wiper INT

(Wiper intermittent dial 4)

JPMIA0196GB

1.3 V

WCS-54
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF C

JPMIA0165GB

1.4 V D

Turn signal switch RH

F
JPMIA0166GB

1.3 V
G

Combination
8 Combination switch switch
H
Ground Input Turn signal switch LH
(V) INPUT 1 (Wiper intermit-
tent dial 4)

JPMIA0167GB
I
1.3 V

Front wiper switch LO

K

JPMIA0168GB

1.3 V L

Front washer switch ON

WCS
JPMIA0196GB

1.3 V
O

WCS-55
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

JPMIA0165GB

1.4 V

Lighting switch 2ND

JPMIA0166GB

1.3 V

9 Combination
Combination switch switch
(G)*3 Ground Input Lighting switch PASS
INPUT 2 (Wiper intermit-
(B)*4 tent dial 4)

JPMIA0167GB

1.3 V

Front wiper switch INT

JPMIA0168GB

1.3 V

Front wiper switch HI

JPMIA0196GB

1.3 V

WCS-56
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.3 V D

E
Front fog lamp switch ON
(Wiper intermittent dial 4)
F
JPMIA0167GB

1.3 V
G

10 Combination switch Combination Rear fog lamp switch ON

H
Ground Input
(BR) INPUT 5 switch (Wiper intermittent dial 4)

JPMIA0168GB
I
1.3 V

Rear wiper switch ON

(Wiper intermittent dial 4) K

JPMIA0169GB

1.3 V L

Any of the condition below

M
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 6 WCS
• Wiper intermittent dial 7
JPMIA0196GB

1.3 V
11 Input/ O
Ground Audio link — — —
(B) Output

WCS-57
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

OFF
(When rear door RH
12 Rear door closed)
Ground Rear door switch RH Input
(LG) switch RH
PKID0924E

11.2 V
ON
(When rear door RH 0V
opened)

OFF
13 Back door (When back door closed)
Ground Back door switch Input
(V) switch
PKID0924E

11.2 V
ON
0V
(When back door opened)

OFF
(When passenger door
14
Passenger door Passenger door closed)
(P)*3 Ground Input
switch switch
(BR)*4 PKID0924E

11.2 V
ON
(When passenger door 0V
opened)

OFF
15 (When driver door closed)
Driver door
(BR)*3 Ground Driver door switch Input
*4
switch
(P) PKID0924E

11.2 V
ON
(When driver door 0V
opened)

WCS-58
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

OFF
(When rear door LH C
16 Rear door closed)
Ground Rear door switch LH Input
(GR) switch LH
PKID0924E

11.2 V D
ON
(When rear door LH 0V
opened) E
17 Door lock status indi- Door lock status ON 12 V
Ground Output
(L) cator indicator OFF 0V
F

G
20 Rear window defog- Rear window Not pressed
Ground Input
(SB) ger switch defogger switch
H
JPMIA0154GB

1.1 V
While pressing 0V
I
21 Input/
— CAN-L — —
(P) Output
22 Input/
(L)
— CAN-H
Output
— — J

ON 0V

23 Security indica- L
Ground Security indicator Output Blinking
(V) tor

JPMIA0014GB
M
10.3 V
OFF 12 V
Ignition switch OFF or ACC 12 V WCS

24 Light & rain sensor Input/

O
Ground
(GR) serial link Output Ignition switch ON

P
JPMIA0156GB

8.7 V
25
Ground Alarm link Output — —
(G)

WCS-59
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

26
Blower fan motor Blower fan mo- OFF
(GR)*5 Ground Input
switch tor switch
(LG)*6
PKID0924E

11.2 V
ON (other than OFF) 0V

Compressor ON is not re-

quested from auto amp.
(A/C indicator OFF, blow-
er fan motor switch OFF
27
Ignition switch or etc.)
(P)*5 Ground A/C switch Input
*6
ON PKID0924E
(Y) 11.2 V
Compressor ON is re-
quested from auto amp.
(A/C indicator ON and 0V
blower fan motor switch
ON).
Ignition switch OFF or ACC 0V

28
(LG)*7 Ground Shock detect sensor Input
Ignition switch ON
(R)*8

JPMIA0155GB

6.0 V

29
Back door opener Back door Not pressed
(LG)*3 Ground Input
switch opener switch
(O)*4
JPMIA0154GB

1.2 V
Pressed 0V

32 Door lock/unlock Door lock/un- Not pressed

Ground
(BR) switch (Unlock) Input lock switch

JPMIA0154GB

1.2 V
Pressed to the unlock side 0 V

WCS-60
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

33
OFF C
(W)*9 Ground Hazard switch Input Hazard switch
(Y)*10
JPMIA0154GB

1.3 V D
ON 0V

34
Door lock/unlock Door lock/un- Not pressed F
(SB)*3 Ground
switch (Lock) Input lock switch
(P)*4
JPMIA0154GB

1.2 V G
Pressed to the lock side 0V

35 Headlamp washer Headlamp Not pressed I

Ground
(G) switch Input washer switch

JPMIA0154GB
J
1.2 V
Pressed to the lock side 0V
All switch OFF 0V K
Turn signal switch RH
Lighting switch 2ND
Combination
Lighting switch HI
L
36 Combination switch switch
Ground Output
(G) OUTPUT 5 (Wiper intermit-
tent dial 4)
Lighting switch 1ST M
JPMIA0164GB

9.1 V
All switch OFF WCS
0V
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4)
O
Rear washer switch ON
(Wiper intermittent dial 4)
37 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Any of the condition below P
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 5
• Wiper intermittent dial 6 JPMIA0161GB

9.1 V
Rear wiper switch ON
(Wiper intermittent dial 4)

WCS-61
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF 0V
Front wiper switch LO
Front wiper switch MIST
Combination
38 Combination switch switch Front wiper switch INT
Ground Output
(W) OUTPUT 3 (Wiper intermit- Lighting switch AUTO
tent dial 4)

Rear fog lamp switch ON JPMIA0162GB

9.3 V
All switch OFF 0V
Turn signal switch LH
Lighting switch PASS
Combination
39 Combination switch switch Lighting switch 2ND
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Front fog lamp switch ON
JPMIA0163GB

9.3 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Any of the condition below
40 Combination switch Combination with all switch OFF
Ground Output • Wiper intermittent dial 1
(P) OUTPUT 1 switch
• Wiper intermittent dial 2
• Wiper intermittent dial 3
• Wiper intermittent dial 6
• Wiper intermittent dial 7 JPMIA0160GB

Rear wiper switch INT 9.1 V

(Wiper intermittent dial 4)
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage
(LG) ply

42 Interior room lamp Interior room lamp battery saver activation 0V

Ground Output
(V) power supply Interior room lamp battery saver no activation 12 V

43 Rear wiper switch OFF 0V

Ground Rear wiper motor Output
(SB) Rear wiper switch ON 12 V

Rear wiper stop position

44 Ignition switch
Ground Rear wiper auto stop Input
(B) ON
JPMIA0197GB

Any position other than

0V
rear wiper stop position

WCS-62
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

45 Back door lock actu- Back door Pressed

(V)
Ground
ator
Output
opener switch
C

SKIA9232E
D
Not pressed 0V
Turn signal switch OFF 0V
E

47 Ignition switch
Ground Turn signal LH Output
(BR) ON Turn signal switch LH F

PKID0926E G
6.5 V
Turn signal switch OFF 0V
H

48 Ignition switch
Ground Turn signal RH Output I
(GR) ON Turn signal switch RH

PKID0926E J
6.5 V

49 OFF 0V
Ground Rear fog lamp Output Rear fog lamp
(Y) ON 12 V K
50 Unlock 5V
Ground Unlock sensor Input Driver's door
(G) lock 0V
L
51 Depress the brake pedal Battery voltage
Ground Stop lamp switch Input
(R) Release the brake pedal 0V

52 Room lamp timer Interior room OFF 12 V M

Ground Output
(R) control lamp ON 0V

53 Power window pow- OFF or ACC 0V

(L)
Ground
er supply (IGN)
Output Ignition switch WCS
ON 12 V

O
Door unlock Pressed to the unlock side
54 Door lock/un-
Ground (All other than driv- Output
(O) lock switch
er's door) P

SKIA9232E

Not pressed 0V
55
Ground Ground — Ignition switch ON 0V
(B)

WCS-63
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Not pressed 0V

56 Door lock (All) and Door lock/un-

Ground Output
(V) fuel lid lock lock switch Pressed to the lock side

SKIA9232E

57 Battery power sup-

Ground Input Ignition switch OFF Battery voltage
(Y) ply
58 Power window pow-
Ground Output Ignition switch OFF 12 V
(P) er supply (BAT)
When lock button of key fob or Intelligent Key
0V
59 is not pressed
Ground Super lock Output
(R) When lock button of key fob or Intelligent Key
12 V
is pressed

60 Driver's door unlock Door lock/un- Pressed to the unlock side

Ground Output
(G) and fuel lid unlock lock switch

SKIA9232E

Not pressed 0V
*1: With Intelligent Key
*2: Without Intelligent Key
*3: RHD models
*4: LHD models
*5: With gasoline engine
*6: With diesel engine
*7: RHD models with side air bag
*8: LHD models with side air bag
*9: With xenon headlamp and daytime light system
*10: Except with xenon headlamp and daytime light system

WCS-64
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - BCM - INFOID:0000000001541680

WCS

JCMWA0500GB
P

WCS-65
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCMWA0501GB

WCS-66
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

WCS

JCMWA0502GB

WCS-67
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCMWA0503GB

WCS-68
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

WCS

JCMWA0504GB

WCS-69
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCMWA0505GB

WCS-70
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

WCS

JCMWA0506GB

P
Fail Safe INFOID:0000000001367525

FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC is detected.

WCS-71
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DTC Fail-safe Cancellation

• Inhibits engine cranking
B2190: NATS ANTENNA AMP • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2191: DIFFERENCE OF KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
• Inhibits engine cranking
B2194: DISCORD BCM-I-KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2195: ANTI SCANNING • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2196: DONGLE NG • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)

REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper auto stop signal.
When the rear wiper auto stop signal does not change more than 5 seconds while driving the rear wiper, BCM
stops power supply to protect the rear wiper motor.
Condition of cancellation
1. Turn ignition switch OFF.
2. Pass more than 1 minute after the rear wiper stop.
3. Turn ignition switch ON.
4. Operate the rear wiper switch.
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY LIGHT & RAIN SENSOR MALFUNCTION
BCM detects the light & rain sensor serial link error and the light & rain sensor malfunction.
BCM controls the following fail-safe when light & rain sensor has a malfunction.
Fail-safe Control
• Auto light control: Headlamp is turned ON.
• Front wiper control: The condition just before the activation of fail-safe is maintained until the front wiper
switch is turned OFF.
DTC Inspection Priority Chart INFOID:0000000001367526

Priority DTC
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
• B2196: DONGLE NG

WCS-72
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DTC Index INFOID:0000000001367527

A
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- B
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter C
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
D
DTC TIME Fail-safe Reference
U1000: CAN COMM CIRCUIT 0 1 - 39 — BCS-33
U1010: CONTROL UNIT (CAN) 0 1 - 39 — BCS-34 E
• With Intelligent Key system: SEC-41
B2190: NATS ANTENNA AMP CRNT PAST × • Without Intelligent Key system: SEC-
254 F
• With Intelligent Key system: SEC-43
B2191: DIFFERENCE OF KEY CRNT PAST × • Without Intelligent Key system: SEC-
256
G
• With Intelligent Key system: SEC-38
B2192: ID DISCORD BCM-ECM CRNT PAST × • Without Intelligent Key system: SEC-
251
H
• With Intelligent Key system: SEC-40
B2193: CHAIN OF BCM-ECM CRNT PAST × • Without Intelligent Key system: SEC-
253
B2194: DISCORD BCM-I-KEY CRNT PAST × SEC-53 I
• With Intelligent Key system: SEC-54
B2195: ANTI SCANNING CRNT PAST × • Without Intelligent Key system: SEC-
264 J
• With Intelligent Key system: SEC-55
B2196: DONGLE NG CRNT PAST × • Without Intelligent Key system: SEC-
265 K

WCS

WCS-73
 THE LIGHT REMINDER WARNING DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description INFOID:0000000001080363

The light reminder warning does not sound under the following conditions.
• Lighting switch 1ST or 2ND position
• Driver door open
• Ignition switch OFF or ACC
Diagnosis Procedure INFOID:0000000001080364

1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION

Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES >> GO TO 2.
NO >> Refer to EXL-193, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table".
2.CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL CIRCUIT
Perform the inspection for the front door switch (driver side) signal circuit. Refer to DLK-83, "DRIVER SIDE :
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK FRONT DOOR SWITCH (DRIVER SIDE) UNIT
Perform a unit inspection for the front door switch (driver side). Refer to DLK-84, "DRIVER SIDE : Component
Inspection".
Is the inspection result normal?
YES >> Replace the BCM. Refer to BCS-68, "Removal and Installation".
NO >> Replace the front door switch (driver side). Refer to DLK-292, "Removal and Installation".

WCS-74
 THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
A
DOES NOT SOUND
Description INFOID:0000000001080367
B
• The parking brake warning buzzer sounds continuously during vehicle travel even though the parking brake
is released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking C
brake applied.
Diagnosis Procedure INFOID:0000000001080368

D
1.CHECK PARKING BRAKE WARNING LAMP OPERATION
1. Start engine.
2. Check the operation of the parking brake warning lamp when operating the parking brake. E

Condition Warning lamp status

F
Parking brake ON ON
Parking brake OFF OFF
Is the inspection result normal? G
YES >> Replace combination meter.
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT H

Perform an inspection for the parking brake switch signal circuit. Refer to WCS-17, "Diagnosis Procedure".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK PARKING BRAKE SWITCH UNIT J
Perform a unit inspection for the parking brake switch. Refer to BRC-47, "Component Inspection".
Is the inspection result normal?
K
YES >> Replace combination meter.
NO >> Replace parking brake switch.

WCS

WCS-75
 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000001558903

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

WCS-76