ALUMINIUM

Alumeco A/S is ISO 9001certified

2
Company Profile and Map
Aluminium Sheets/Plates
Aluminium Coils

Aluminium Tread Plates

Aluminium Barely Seed Plates
Aluminium Gangway Profiles

Aluminium Bars - Round

Aluminium Bars - Square
Aluminium Bars - Hexagonal

Aluminium Profiles - Flat

Aluminium Profiles - U, T, L
Aluminium Tubes - Square and Rectangular
Aluminium Profiles - Nature Anodized

Aluminium Profiles - Bulb

Aluminium Tubes - Round
Aluminium - Roller Tubes
Aluminium - Cylinder Tubes

Aluminium - Fittings
Transport Systems

Aluminium - Cargo Sections

Aluminium/Steel - Joint Compositions
Aluminium - Strongbacking

Aluminium - Special Profiles

Colour Marks According to Alloy

Machining

Technical Information
Reference Table

Terms of Sale and Delivery Edition 2015

Company Profile

Alumeco A/S, Odense

Alumeco A/S
Who is Alumeco A/S
Alumeco is the leading aluminium whole­
saler in Alumeco A/S was established in 1983. Since then the
Scandinavia. We are a modern trading company work­ company has expanded and today the group has seve­
ing in accordance with the motto “Just in time”. Our ral subsidiaries abroad.
prime duty is to meet the demands of our
customers.

Scandinavia's most extensive aluminium

stock
From our head office at Naesbyvej in Odense,
Alumeco offers a very wide range of aluminium profi­
les, special profiles, bars, tubes, plates and coils. We
have Scandinavia's most extensive stock with more
than 5000 tons of aluminium. In addition Alumeco has
its own service center, enabling us to offer sawing of
plates and profiles as well as foil application.

4
How to find Alumeco A/S

MOTEL
NÆSBYLUND KRO

Address
Alumeco A/S GAMMELSØ

Naesbyvej 26
DK-5000 Odense C.
Phone: +45 66 17 81 17
Fax: +45 66 14 58 71
NÆ
SB

VE
Email: [email protected]
Y

Web: www.alumeco.com
ÅLØKKE ALLÈ

RADISON SAS
H.C. ANDERSEN
EJ

HOTEL - ODENSE
NSV
TIO
TA
RE S
ØST

PLAZA
HOTEL
ODENSE

RUGÅRDSVEJ

53
EJ
LØKKEV

161 Odense V
Havn
GRØN

Blommenslyst
Motorway Middelfart/Odense E20
Exit 53 on the motorway
kkevej is approx. 12 km
rønlø
to G MIDDELFARTVEJ
ce
istan
D

E20

5
Aluminium Sheets/Plates / Aluminium Coils

Chemical Composition: EN AW-1050A - EN 573-3: 2009

Si Fe Cu Mn Mg Zn Ti Others Al

0.25 0.4 0.05 0.01 0.05 0.07 0.05 0.03 99.5

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress Rp 0.2 N/ A50 mm A hardness
mm2 HBS
mm min. max. min. % min. % min.
O/H111 0,5-80 65 95 20 22-35 20
H112 6,0-80 70-75 145 25-30 20 22-23
H14 0,2-25 105 145 85 2-6 34
H24 0,2-12,5 105 150 75 3-8 33
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Good Not suited for anodizing Excellent

6
Aluminium Sheets/Plates - EN AW-1050A
EN 573-3, 485-1, 485-2, 485-3, 485-4
Thickness Kg/ 1000 x 2000 mm Kg/pcs. 1250 x 2500 mm Kg/pcs. 1500 x 3000 mm
pcs. H14/ H14/
mm H24 DDQ Stucco H24 DDQ Stucco H14/H24

0.5 2.7 • 4.3 •

0.6 3.3 •
0.7 3.8 • • 8.5 •
1.0 5.4 • • • 8.5 • • 12.2 •
1.25 6.8 • • 10.6 • • 15.2 •
1.5 8.1 • • 12.7 • • • 18.3 •
2.0 10.8 • • 17.0 • • 24.3 •
2.5 13.5 • 21.1 • 30.5 •
3.0 16.2 • 25.4 • 36.6 •
4.0 21.6 • 34.0 • 48.8 •
5.0 27.0 • 42.2 • 61.0 •
6.0 32.4 • 50.7 • 72.9 •
Stocked in deep drawn quality (DDQ). We also stock: 1.5 x 1500 x 4000 mm; 2.0 x 1500 x 4000 mm; 2.0 x 2000 x 3000 mm
All sheets/plates can be supplied with PE-foil.

SHEETS CUT-TO-LENGTH
Aluminim Coil: Alloy EN AW-1050A H14
EN 573-3, 485-1, 485-2, 485-4 Alumeco cuts and delivers in
dimensions you need. Your ad­
Dimension Kg/coil vantages:
0.7x1000 mm 500 kg
• Less waste
1.0x1000 mm 500 kg
• Limited stock
1.0x1000 mm 1000 kg • Quick and flexible delivery
1.5x1250 mm 1200 kg
CONTACT US FOR OFFER
2.0x1250 mm 1500 kg

Aluminim Coil: Alloy EN AW-1050A H14 Stucco

EN 573-3, 485-1, 485-2, 485-4

Dimension Kg/coil
0.7x1000 mm 500 kg
0.8x1000 mm 250 kg
Stucco
0.8x1000 mm 1000 kg
1.0x1000 mm 500 kg

Aluminium Coil for insulation

EN 573-3, 485-1, 485-2, 485-4

3003 H14 5052 H22 Coated RAL 9005* Coated RAL 9010*
Dimension Kg/coil Kg/coil Kg/coil Kg/coil
0.63x1000 mm 250 / 1000 kg 500 kg
0.70x1000 mm 500 kg 500 kg
0.88x1000 mm 250 / 1000 kg 250 / 500 kg
0.75x1000 mm 250 / 1000 kg 250 / 500 kg
1.00x1000 mm 250 / 1000 kg 250 / 500 kg 500 kg 500 kg

7
Aluminium Sheets/Plates

Chemical Composition: EN AW-5754 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.4 0.1 0.5 2.6-3.6 0.3 0.2 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress Rp 0.2 N/ A50 mm A hardness
mm2 HBS
mm min. max. min. % min. % min.
O/H111 0.5-12.5 190 240 80 12-18 52
O/H111 12.5-100 190 240 80 17 52
H112 12.5-25 190 90 10 58
H22/32 0.20-12.5 220 270 130 7-10 63
H24/34 0.20-12.5 240 280 160 6-10 70
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Excellent Good Excellent

8
Aluminium Sheets/Plates - Sea water-resistant - EN AW-5754
EN 573-3, 485-1, 485-2, 485-3, 485-4
Thickness Kg/pcs. 0.5-6 x 1000 x 2000 mm Kg/pcs. 0.7-6 x 1250 x 2500 mm Kg/pcs. 1-6 x 1500 x 3000 mm
mm 8-60 x 1020 x 2020 mm 8-30 x 1270 x 2520 mm 8-140 x 1520 x 3020 mm
H22/32 H112/H111 H22/32 - H24/34 H112/H111 H22/32 H112/H111

0.5 2.7 •
0.7 3.8 • 5.9 •
1.0 5.4 • 8.5 • 12.2 •
1.2 6.5 • 10.2 •
1.5 8.1 • 12.7 • 18.3 •
2.0 10.8 • 17.0 • 24.3 •
2.5 13.5 • 21.1 • 30.5 •
3.0 16.2 • 25.4 • • 36.6 • •
4.0 21.6 • • 34.0 • • 48.8 • •
5.0 27.0 • • 42.2 • • 61.0 • •
6.0 32.4 • • 50.6 • • 72.9 • •
8.0 44.5 • 69.2 • 99.4 •
10.0 55.7 • 86.4 • 124.2 •
12.0 66.8 • 103.7 • 149.1 •
15.0 83.5 • 129.6 • 186.3 •
20.0 111.3 • 172.8 • 248.4 •
25.0 139.1 • 216.0 • 310.5 •
30.0 166.9 • 259.2 • 372.6 •
*35.0 194.7 • 434.7 •
40.0 222.5 • 496.8 •
50.0 279.0 • 621.0 •
60.0 334.0 • 746.0 •
70.0 893.0 •
80.0 1020.0 •
90.0 1148.0 •
100.0 1276.0 •
120.0 1531.0 •
140.0 1735,0 •
* Price is dimension dependent. All sheets/plates up to and including 8 mm thickness can be supplied with PE-foil.

9
Aluminium Sheets/Plates

Chemical Composition: EN AW-5754 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.4 0.1 0.5 2.6-3.6 0.3 0.2 0.15 Rest

Mechanical Properties:
Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
O/H111 0.5-12.5 190 240 80 12-18 52
H22/32 0.2-12.5 220 270 130 7-10 63
H24/34 0.2-12.5 240 280 160 6-10 70
GradeA 3-12.5 230 140 10-11 63
For more information see page 56

Chemical Composition: EN AW-5083 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.4 0.1 0.4-1.0 4.0-4.9 0.05-0.25 0.25 0.35 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
O/H111 3-6.3 275 350 125 11-15 75
O/H111 6.3-80 270 345 115 14-15 73-75
GradeA 3-12.5 305 220 10-12 89
H116 12.5-40.0 305 215 10 89
H116 40.0-80.0 285 200 10 83
For more information see page 56

10
 Aluminium Sheets/Plates - Sea water-resistant - EN AW-5754 - »Super-size«
EN 573-3, 485-1, 485-2, 485-3, 485-4

Thickness Kg/ 2000 x Kg/ 2000 x

mm pcs. 5000 mm pcs. 6000 mm
3.0 81.0 *•
4.0 130.0 *•
5.0 162.0 •
6.0 195.0 •
7.0 227.0 •
8.0 260.0 •
* Can be supplied with PE-film 1 side.

Aluminium Sheets/Plates - Sea water-resistant - EN AW-5083 - »Super-size«

EN 573-3, 485-1, 485-2, 485-3, 485-4

Thickness Kg/pcs. 2000 x Kg/pcs. 2000 x Kg/pcs. 2500 x

mm 6000 mm 8000 mm 10000 mm
3.0 97.2 •
4.0 130.0 • 172.8 •
5.0 162.0 • 216.0 • 337.5 •
6.0 195.0 • 260.0 • 405.0 •

7.0 227.0 •
8.0 260.0 • 345.0 •
10.0 324.0 • 432.0 •
12.0 389.0 •
15.0 486.0 •
20.0 648.0 •
25.0 810.0 •
30.0 972.0 •
40.0 1295.0 •
50.0
All stated weights are theoretical weights, which may vary.

11
Aluminium Sheets/Plates

Chemical Composition: EN AW-5083 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.4 0.1 0.4-1.0 4.0-4.9 0.05-0.25 0.25 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
O/H111 0.2-6.3 275 350 125 11-15 75
O/H111 6.3-12.5 270 345 115 16 75
O/H111 12.5-80.0 270 345 115 14-15 73-75
O/H111 80.0-120.0 260 110 12 70
O/H111 120.0-200.0 255 105 12 69
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Excellent Protective anodizing Excellent

High tensile strength; particularly used in shipbuilding and

tank industries as well as for moulds in plastic and furniture industries

12
Aluminium Sheets/Plates - Sea water-resistant - EN AW-5083
EN 573-3, 485-1, 485-2, 485-3, 485-4

Thick- Kg/pcs. 2-6 x 1000 x 2000 mm Kg/pcs. 2-6 x 1250 x 2500 mm Kg/pcs. 2-6 x 1500 x 3000 mm
ness 8-20 x 1020 x 2020 mm 8-20 x 1270 x 2520 mm 8-140 x 1520 x 3020 mm
mm 150-220 x 1520 x 2800 mm
2.0 10.8 • 17.0 • 24.3 •
3.0 16.2 • 25.4 • 36.6 •
4.0 21.6 • 34.0 • 48.8 •
5.0 27.0 • 42.2 • 61.0 •
6.0 32.4 • 50.6 • 72.9 •
8.0 99.4 •
10.0 55.7 • 124.2 •
12.0 66.8 • 149.1 •
15.0 83.5 • 186.3 •
20.0 111.3 • 248.4 •
25.0 310.0 *•
30.0 372.0 *•
40.0 496.0 *•
50.0 620.0 *•
60.0 744.0 *•
70.0 868.0 •
80.0 992.0 •
100.0 1239.0 •
110.0 1363.0 •
120.0 1487.0 •
130.0 1611.0 •
140.0 1735.0 •
150.0 1859.0 •
160.0 1983.0 •
180.0 2231.0 •
200.0 2479.0 •
220.0 2727.0 •
All sheets/plates up to and including 8 mm thickness All stated weights are theoretical weights, which may vary.
can be supplied with PE-foil.

Can be supplied in thickness up to 750 mm.

*) Can also be supplied in dimension 2000 x 4000 mm.
Plates from 6 to 20 mm in thickness can be supplied with DNV-certificate.

13
Aluminium Sheets/Plates

Chemical Composition: EN AW-6082 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.7-1.3 0.5 0.1 0.4-1.0 0.6-1.2 0.25 0.2 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
T4 1.5-12.5 205 - 110 12-15 58
T6151 12.5-175 275 - 200 8-12 81
T651 12.5-175 275-295 - 230-240 4-8 83-89
T651 1.5-6 310 - 260 6-10 91-94
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Good Good Excellent

High tensile strength
Particularly used in engineering and tooling industries for construction of moulds etc.

14
Aluminium Sheets/Plates - EN AW-6082 T6/T651
EN 573-3, 485-1, 485-2, 485-3, 485-4
Thickness Kg/pcs. 1-6 x 1000 x 2000 mm Kg/ 2-6 x 1500 x 3000 mm
mm 8-20 x 1020 x 2020 mm pcs. 8-150 x 1520 x 3020 mm
1.0 5.4 •
1.5 8.1 •
2.0 10.8 •
2.5 13.5 •
3.0 16,2 •
4.0 21.6 •
5.0 27.0 • 61.0 •
6.0 32.4 • 72.9 •
8.0 44.5 • 99.4 •
10.0 55.7 • 124.2 •
12.0 66.8 • 149.1 •
15.0 83.5 • 186.3 •
20.0 111.3 • 248.4 •
25.0 310.5 •
30.0 372.6 •
35.0 460.0 *•
40.0 496.0 •
45.0 557.7 *•
50.0 621.0 •
60.0 746.0 •
65.0 806.0 *•
70.0 868.0 •
80.0 994.0 •
90.0 1116.0 *•
100.0 1245.0 •
110.0 1364.0 •
120.0 1488.0 • * Price is dimension dependent.
All sheets/plates up to and including 8 mm
130.0 1612.0 • thickness can be supplied with PE-foil.
140.0 1736.0 •
All stated weights are theoretical weights, which
150.0 1859.0 • may vary.

Aluminium Plates - EN AW 6082 T651 “Special Flatness”

EN 573-3, 485-1, 485-2, 485-3
Thickness Kg/pcs. 1520 x 3020 mm “Special Flatness”
mm
8.0 97.2 • • Extra straightened plates
10.0 124.2 • • Better planeness
12.0 149.1 • Max. 0.15 mm per 100 mm
15.0 186.3 • • Tension annealed
20.0 248.4 • • Less tensions
25.0 310.5 • • Superior surface
30.0 372.6 • • Superior thickness tolerance
• Also supplied cut to length

15
Aluminium Sheets/Plates

Chemical Composition: EN AW-7075 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.5 1.2-2.0 0.3 2.1-2.9 0.18-0.28 5.1-6.1 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
T651 1.5-12.5 540-545 - 460-475 7-8 160-163
T651 12.5-50.0 530-540 - 460-470 5-6 158-161
T651 90-100 460 - 360 3 135
T651 100-120 410 - 300 2 119
T651 120-150 360 - 260 2 104
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Acceptable Protective anodizing Acceptable

High tensile strength
Particularly used in engineering and tooling industries for construction of moulds etc.

Chemical Composition: HOKOTOL

Cu Mg Zn Al
2.1 2.0 6.2 Rest

Mechanical Properties:
Tensile stregth 0.2% proof stress Elongation Brinell­ hardness
Rm N/mm2 Rp 0.2 N/mm2 A50 mm A HBS
min. max. min. max. % min. % max.

550 500 - 4 - 160-180

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Acceptable Protective anodizing Acceptable

Hardness consistency, also in the centre of the plate. Extremely high tensile strength,
wear-resistant and forged. Particularly applicable in the tooling industry, for construction of moulds etc.
We can also offer: Sheets/plates, rings and roundels cut to length, also in small quantities.

16
Aluminium Sheets/Plates - EN AW-7075
EN 573-3, 485-1, 485-2, 485-3
Thickness Kg/ 1000 x Thickness Kg/pcs. 1520 x Thickness Kg/pcs. 1520 x Thickness Kg/pcs. 1520 x
mm pcs. 2000 mm mm 3020 mm mm 3020 mm mm 3020 mm
1.0 5.6 *• 8.0 102.8 *• 40.0 524.4 *• 180.0 2397.0 *•
2.0 11.4 *• 10.0 131.1 *• 50.0 656.0 *• 200.0 2664.0 *•
3.0 16.5 *• 12.0 157.4 *• 60.0 787.0 *• 220.0 2929.0 *•
15.0 196.7 *• 70.0 918.0 *•
20.0 262.2 *• 80.0 1047.0 *•
25.0 327.8 *• 120.0 1598.0 *•
30.0 393.3 *• 150.0 1997.0 *•
35.0 459.9 *• 160.0 2130.0 *•
All sheets/plates can be supplied up to and including 400 mm thickness, but we recommend HOKOTOL thicker than 80 mm.
* Price is dimension dependent.

Typical 0,2 % proof stress Hardness across a 300 mm (12”) thick plate

600 180
HOKOTOL
Hardness HB 2,5/187,5

500 160
Rp0,2 (LT,s/2) [MPa]

HOKOTOL
140
400
120
300 7075 T651
7075 T651 100

200 80
0 50 100 150 200 250 300 350 [mm] 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1
0 4 8 12 [ins.]
Thickness position
Plate thickness

Aluminium Plates - HOKOTOL

Tooling plates as alternative to tooling steel.
EN 485-3
Thickness Kg/pcs. 790 x Kg/pcs. 1270 x Kg/pcs. 1520 x
mm 2200 mm 2520 mm 3020 mm
40.0 524.0 •
51.0 668.0 •
65.0 851.0 •
75.0 989.0 •
85.0 1112.0 •
90.0 1178.0 •
100.0 1309.0 •
110.0 1439.0 •
120.0 1570.0 •
130.0 1701.0 •
140.0 1832.0 •
150.0 1963.0 •
160.0 1449.0 •
180.0 1603.3 •
200.0 984.0 •
All stated weights are theoretical weights, which may vary.
Can be supplied up to 400 mm thickness.
Other dimensions available on inquiry.

17
Aluminium Sheets/Plates

Chemical Composition: EN AC-5083 cast block, sawn on 6 sides

Si Fe Cu Mn Mg Cr Zn Ti Others Al

0.4 0.4 0.10 0.4-1.0 4.0-4.9 0.05-0.25 0.25 0.15 0.15 Rest

Mechanical Properties:
Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
min. % min. % min.
220 - 290 110 - 115 10 - 15 ca. 70 - 75

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability
Very good Good Very good

18
 Aluminium Plates: EN AC-5083 cast block, sawn on 6 sides
Naturally aged, homogenized and stress free
Thickness Kg/pcs. 1020 x 3100 mm Thickness Kg/pcs. 1020 x 3100 mm
mm mm
30 260.9 • 110 956.6 •
40 347.8 • 120 1043.5 •
50 435.0 • 130 1130.5 •
60 521.8 • 140 1217.4 •
70 608.7 • 150 1304.4 •
80 695.7 • 160 1391.3 •
90 782.6 • 200 1739.1 •
We can supply all thicknesses from 10-1000 mm from our stock in Coswig, Germany.

Characteristics Fields of application

• Very good machining properties

• Moulds
• Easy to mill
• Machine construction
• Good corrosion resistance
• Auto parts
• Minimum porosity
• Minimum internal stress

Sawing of thick plates - Alumeco Deutschland GmbH.

19
Aluminium Sheets/Plates

Chemical Composition: Cast Aluminium Plates - EN AC-5083 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al
0.4 0.4 0.1 0.4-1.0 4.0-4.9 0.05-0.25 0.25 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Tensile strength 0.2% proof stress Elongation Brinell­ hardness
Rm N/mm2 Rp 0.2 N/mm2 A50 mm A HBS
min. norm min. norm % min. % max.
275 125 15 70

Special Characteristics:
• Excellent dimensional stability during machining
• High mechanical properties Tolerances
• Minimal porosity Thickness: ± 0.1 mm
• Excellent for anodizing (hard) Flatness: < 12 mm 0.4 mm/m
• Fully machinable Flatness: > 12 mm 0.13 mm/m
• Fully weldable
• Roughness of Ra 0.4 microns
• Excellent corrosion resistance
• Good mechanical properties at elevated temperatures

20
Cast Aluminium Plates - EN AC-5083
Surface: Precision milled on both sides, with protective foil.

Thickness Kg/pcs. 1240 x 3048 mm Kg/pcs. 1520 x 3020 mm Kg/pcs. 1540 x 3048 mm
mm
6.35 64.8 •
8.00 101.4 •
10.00 124.0 •
12.00 148.8 •
15.00 185.9 •
20.00 247.9 •
25.00 309.9 •
30.00 371.8 •
35.00 433.8 •
40.00 495.8 •
50.00 619.7 •
60.00 760.4 •
80.00 1013.9 •

21
Aluminium Sheets/Plates

Chemical Composition: "Weldural"

Si Fe Cu Mn Mg Cr Zn Zr Ti Al
0.30 0.4 5.8-6.8 0.2-0.4 0.1 0.05 0.1 0.1-0.25 0.1 Rest

Mechanical Properties:
Thickness Tensile strength 0.2% proof stress Elongation Brinell­ hardness
Rm N/mm2 Rp 0.2 N/mm2 A50 mm A HBS
mm min. norm. min. norm. % min. % max.
100.0 455 350 7.5 130
200.0 440 335 6.5 130
300.0 405 320 3.5 130
400.0 365 305 2.5 130
500.0 345 295 1.5 130
600.0 395 315 3.5 130
700.0 395 315 3.5 130

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability
Acceptable Protective anodising Very good

Chemical Composition: EN AW-2017A - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al
0.2-0.8 0.7 3.5-4.5 0.4-1.0 0.4-1.0 0.1 0.25 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof stress Elongation Brinell­
Rm N/mm2 Rp 0.2 N/mm2 A50 mm A hardness
HBS
mm min. max. min. % min. % min.
T451 1.5 - 6.0 390 245 15 110
T451 6.0 - 12.5 390 260 13 111
T451 12.5 - 40.0 390 250 12 110
T451 40.0 - 60.0 385 245 12 108
T451 60.0 - 80.0 370 240 7

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability
Acceptable Protective anodising Acceptable

22
Aluminium Plates - “Weldural”
Tooling plates as alternative to tooling steel.

Thickness Kg/pcs. 1650 x 3020 mm Thickness Kg/pcs. 1500 x 3020 mm

mm mm
80.0 1156.0 • 250.0 3285.0 •
100.0 1445.0 • 280.0 3679.0 •
120.0 1734.0 • 300.0 3941.0 •
140.0 2023.0 • 320.0 4204.0 •
150.0 2168.0 • 350.0 4598.0 •
160.0 2312.0 • 400.0 5255.0 •
180.0 2601.0 • 450.0 5911.0 •
200.0 2896.0 • 500.0 6570.0 •
220.0 3179.0 •

Aluminium Plates - EN AW-2017A

EN 573-3, 485-1, 485-2, 485-3, 485-4

Thickness Kg/pcs. 1520 x 3020 mm

mm
5.0 64.3 •
6.0 77.2 •
8.0 102.9 •
10.0 128.6 •
12.0 154.3 •
15.0 192.8 •
20.0 257.1 •
25.0 321.4 •
30.0 385.6 •
50.0 643.0 •
60.0 772.0 •
70.0 900.0 •
80.0 1029.0 •
90.0 1157.0 •
100.0 1286.0 •

23
Alloy overview

Wide selection of alloys

The table below sums up a number of the alloys and corresponding thickness directly available from Denmark or Germany.

Thickness EN AW-5754 EN AW-5083 EN AW-6082 EN AW- EN AW-7075 Weldural Hokotol EN AC-5083 EN AC-5083
2017A precision milled sawn
mm DE DK DE DK DE DK DE DE DK DE DE DK DE DK DE DK
1 • • •
2 • • • • •
3 • • • • • •
4 • • • • • •
5 • • • • • • • •
6 • • • • • • • • • •
8 • • • • • • • • • • • •
10 • • • • • • • • • • • •
12 • • • • • • • • • • • •
15 • • • • • • • • • • • •
20 • • • • • • • • • • • •
25 • • • • • • • • • • • •
30 • • • • • • • • • • • •
35 • • • • • • • • • • •
40 • • • • • • • • • • • • •
45 • • • • • • • • •
50 • • • • • • • • • • • • •
51 • •
55 • • • • • • • •
60 • • • • • • • • • • • • •
65 • • •
70 • • • • • • • • • • • •
75 • • •
80 • • • • • • • • • • •
85 •
90 • • • • • • • • • • •
100 • • • • • • • • • • •
110 • • • • • •
120 • • • • • • • • • •
130 • • • • • •
140 • • • • • • •
150 • • • • • • • •
160 • • • •
180 • • • •
200 • • • • •
220 • • •
250 • • •
280 • •
300 • • •
320 • •
350 • •
400 • •
450 • •
500 • •

Standard rolled plate dimensions Max. dimensions of cast blocks

Thickness Max. width Max. length 610 mm x 1350 mm x 3100 mm
6 - 150 mm 1520 mm 3020 mm 595 mm x 1100 mm x 3100 mm
150 - 520 mm 1520 mm 2800/3020 mm 1000 x 1650 x 1800 mm

24
Special alloys

Cast aluminium – 5083 alloy

Our cast aluminium is available sawn on six sides.
Characteristics:
• Easy to mill
• Minimum porosity
• No rolling structure
• Internal stress is reduced to the absolute
minimum to obtain extreme precision, also
after machining

Cast and precision milled – 5083 alloy

The precision-milled EN AC-5083 plates have the
following additional advantages:
• Flatness tolerances to a minimum of
0.13 mm/metre ≥15 mm thick Mould for car headrest (made by W. Olsen)
• Thickness tolerances of +/- 0.127 mm
Hokotol – 7000 alloy
• Roughness: Ra 0.64 my
Fields of application:
• Foil on both sides
• Moulds for blow forming and injection
Precision part in 5083
moulding for the plastics industry
• Punching tools
• Machine parts requiring high strength combi-
ned with low weight
• Moulds for casting plastic window frames

Characteristics:
Weldural – 2219 alloy • Lightweight
Fields of application: • Easy to mill
• Precision parts for the machine industry due to • Extremely uniform mechanical properties
high dimensional stability throughout the entire thickness of the plate
• Machine parts • Resistant to wear
• Moulds
• Good polishing properties
• Suitable for high temperatures
• Excellent dimensional stability by stress relieved
• Refrigeration engineering
stretching or cold compressing
• Good thermal conductivity
Characteristics:
• High strength under heat stress
• Medium and high strength
• Resistant to wear
• Excellent weldability
• Good polishing properties
• Good corrosion resistance
• Extremely uniform mechanical properties
throughout the entire thickness of the plate
• Excellent dimensional stability by stress relieved
stretching or cold compressing
• Good thermal conductivity
Blow mould tank in Weldural

25
Aluminium Sheets/Plates

Chemical Composition: EN AW-5005 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.3 0.7 0.20 0.20 0.5-1.1 0.10 0.25 0.15 Rest

Mechanical Properties - EN 485-2: 2008

Temper Thickness Tensile strength 0.2% proof Elongation Brinell­
Rm N/mm2 stress A50 mm A hardness
Rp 0.2 N/mm2 HBS
mm min. max. min. % min. % min.
H14 0.2-1.5 145 185 120 2 48
H24/H34 0.5-6 145 185 110 4-6 47
For more information see page 56

Special Characteristics:
Corrosion resistance Suitability for anodizing Weldability

Good Vey good Good

Specially suited for decorative anodizing

26
Aluminium Sheets EN AW-5005 H14 - normal quality
EN 573-3, 485-1, 485-2, 485-4

Thickness Kg/pcs. 2000 x 4000 mm

mm
2.0 43.2 •
3.0 65.0 •
Available with and without foil.

Aluminium Sheets EN AW-5005 H14 - Guaranteed Anodizing Quality

1 side covered with PE-foil. EN 573-3, 485-1, 485-2, 485-4
Thickness Kg/pcs. 1000 x Kg/pcs. 1250 x Kg/pcs. 1500 x Kg/pcs. 2000 x
mm 2000 mm 2500 mm 3000 mm 4000 mm
1.0 5.4 • 8.5 • 12.2 •
1.5 8.1 • 12.7 • 18.3 •
2.0 10.8 • 17.0 • 24.3 • 43.2 •
2.5 13.5 •
3.0 16.2 • 25.3 • 36.6 •

Aluminium Sheets EN AW-5005 H14 - Nature anodized 15-20 my

1 side covered with PE-foil. EN 573-3, 485-1, 485-2, 485-4
Thickness Kg/pcs. 1000 x 2000 mm Kg/pcs. 1250 x 2500 mm Kg/pcs. 1500 x 3000 mm
mm
1,0 5,4 • 8,5 • 12,2 •
1,5 8,1 • 12,7 • 18,3 •
2,0 10,8 • 17,0 • 24,3 •
3,0 16,2 • 25,3 • 36,6 •

Stainless Steel look aluminium sheets - SSL

Aluminium sheets looking like stainless steel with laser foil on 1 side
Thickness Kg/pcs. 1250 x 2500 mm
mm
1.0 8.5 •
1.5 12.7 •
Dirt resistant, Corrosion resistant, UV-resistant, antistatic and uniform structure.
Other dimensions on request.

Samples can be sent on request

27
Aluminium Sheets - Coil Coated

Aluminium Sheets Coated

Polyester coated, liquid painting, 1 side covered with PE-foil.
EN 573-3, 485-1, 485-4,1396, 10204

White White Black Silver Antracit grey

Format Kg/ Signal Signal Signal Signal
Thickness RAL 9010 NCS 0500 RAL 9005 RAL 9006 RAL 7016
mm pcs. yellow red blue green
finish 80-90 finish 80-90 finish 30-40 finish 30-40 finish 80-90

0.6 mm 1000x2000 3.3 •

0.8 mm 1250x2500 5.4 •
1.0 mm 1000x2000 5.4 •
1.0 mm 1250x2500 8.5 • • • •
1.0 mm 1500x3000 12.2 •
1.5 mm 1000x2000 8.1 • •
1.5 mm 1250x2500 12.7 • • • •
1.5 mm 1500x3000 18.3 • • • • •
1.6 mm 1250x2500 13.5 • • • •
1.8 mm 1250x2500 9.8 •
1.8 mm 1500x3000 15.2 •
2.0 mm 1500x3000 24.3 •

For technical reasons, the colour samples above can

vary from the colour of the painted sheets.

Please ask for colour samples

Aluminium Coil Coated

EN 573-3, 485-1, 485-4, 1396, 10204

Colour Dimension Kg/coil

mm
0.6x1220mm coil white stucco 500 kg
0.6x1220mm coil oliven stucco 500 kg
0.6x1220mm coil grey stucco 500 kg
0.6x1220mm coil red stucco 500 kg

0.9x1250mm coil NCS 0502Y with foil 1 side 500 kg

0.7x1000mm coil RAL 9005 with foil 1 side 500 kg

1.0x1000mm coil RAL 9005 with foil 1 side 500 kg
0.7x1000mm coil RAL 9010 with foil 1 side 500 kg
1.0x1000mm coil RAL 9010 with foil 1 side 500 kg

28
Coated sheets

Overview of coating types

Coated aluminium sheets are most often used in the building, sign and insulation sectors. In general there are two
types of coated aluminium sheets: liquid painted and powder painted. Below is an overview of the two types and
their characteristics:

Definition Types Advantages Disadvantages

Liquid painting Polyester • Excellent resistance to abra­ • Bad chemical resistance
Polyurethane sion and knocks (Polyamide) (Polyrethane)
Liquid paint is applied
Polyamide • Resistant to chemical,
to the sheet with a
roller and is then heat mechanical and corrosive
PVDF
dried to harden the effects (PVDF)
paint. • Excellent elasticity (PVDF)
• Good chemical resistance
(Polyamide)
• Good coating elasticity
• Good resistance to UV
(Polyamide)
• PVDF has 24+ years life
expectancy

Powder painting Thermoplastic • High material exploitation • Bad resistance to weather

during production – no evap­ (Polyethylene, epoxy)
The sheet is coated oration • Bad resistance to UV
Polyethylene
with a thermoset layer • Easy to apply thicker layer (Polyester)
of powder. The paint is Polypropylene
then hardened by heat- Vinyl • Excellent resistance to abra­ • Bad resistance to weather
treating the sheet. sion and knocks (Polyamide) (Polyester)
Polyamide
• Resistant to chemical effects • Wastage during production
Polyester
(Polyethylene, vinyl) in the form of evaporation if
• Good adherence (polyester) there is over-spraying

• Good resistance to weather

Thermosetting
(polyester, vinyl)
• High corrosion stability
Epoxy
• Good coating elasticity
Polyester
• Good formability
Epoxy-polyester
(mix) • Good mechanical features
(Epoxy)
• Easy to apply finer thickeness
• Sheets can be scored without
the paint cracking
• Polyester has 16 years life
expectancy

NB: When ordering coated sheets it is a good idea to order the entire load in one go to avoid slight
differences in colour as a result of further orders being filled from different batches.

Alloys and maintenance

When using coated sheets in construction, Alumeco A/S recommends using sheets made of aluminium alloy
EN AW-5754 as this has corrosion resistance properties. The use of other alloys invalidates the guarantee. The
sheet surface should be maintained by being cleaned at least once a year to uphold the guarantee for the mate­
rial supplied.

29
Aluminium Tread Plates / Barely Seed Plates / Gangway Profiles

Chemical Composition: EN AW-5754 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.4 0.4 0.1 0.5 2.6-3.6 0.3 0.2 0.15 Rest

Mechanical Properties:
Temper Thickness Tensile strength 0.2% proof stress Elongation Brinell­
Rm N/mm2 Rp 0.2 N/mm2 A50 mm A hardness
HBS
mm min. max. min. % min. % min.
H114 1.5-3 240 310 100 8 60
H114 3-20 240 310 100 10-13 16 60
H244 1.5-3 300 360 220 2
For more information see page 56

We can also supply:

One bar (Not in stock) Quintet

Barely Seed Duet (Not in stock)

Gangway profiles Example of application

30
Aluminium Tread Plates Quintet - Sea water-resistant
EN AW-5754 H114 - EN AW 5086-H244
EN 573-3. 1386
Size Kg/ Thickness Kg/ Thickness Kg/ Thickness Kg/ Thickness Kg/ Thickness
mm pcs. 2/4 mm pcs. 3/4 mm pcs. 3/5 mm pcs. 5/7 mm pcs. 7/9 mm
1000 x 2000 13.0 • 18.0 • 30.0 • 40.0 •
1250 x 2500 20.0 • 29.0 • 47.0 • 63.0 •
1250 x 3000 34.0 • 57.0 •
1500 x 3000 29.0 • 41.0 • 67.5 *• 90.0 •
2000 x 4000 72.0 *• 120.0 *•
2500 x 7000 160.0 ** •
2500 x 8000 183.0 ** •
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.
** Primed on the back of the plate.

Aluminium Barely Seed Plates - Sea water-resistant

EN AW-5754 H244 - EN AW 5086 H244
EN 573-3, 1386
Thickness Kg/pcs. 1250 x Kg/pcs. 2500 x Kg/pcs. 2500 x
mm 2500 mm 8000 mm 9000 mm
1.5/2 14.7 •
2/2.5 19.0 •
2.5/3 23.0 •
3/3.5 183.0 ** • 206.0 ** •
** Primed on the back of the plate.

Aluminium Gangway Profile - Sea water-resistant - Anti-slip surface

EN AW-6060
EN 755 - 1, 755-2, 755-9
Extremely suitable for gangways, stairs etc. Can be supplied cut to length subject to inquiry.
Profile Kg/m Size Ix-value Wx-value 250

no. mm 4 mm 3
P 12234 3.93 250 x 40 mm 294020 11585 40
3
P 12234
25

Profile Kg/m Size Ix-value Wx-value 250

no. mm 4 mm 3
P 16062 4.38 250 x 60 mm 891900 23380 2,8

Not in stock. 60

3 4

P 16062
35 25

Profile Kg/m Size Ix-value Wx-value 300

no. mm 4 mm 3
P 13694 3.83 300 x 35 mm 215000 8244 3
35

P 13694
25

31
Aluminium Bars - Round

Chemical Composition: EN AW-6060 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al
0.30-0.6 0.10-0.30 0.10 0.10 0.35-0.6 0.05 0.15 0.15 Rest
Special Characteristics:
Extremely suitable for anodizing, good weldability.

Chemical Composition: EN AW-6082 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al
0.7-1.3 0.5 0.1 0.4-1.0 0.6-1.2 0.25 0.2 0.15 Rest
Special Characteristics:
High corrosion resistance, good weldability, high strength, suitable for anodizing.

Chemical Composition: EN AW-2007 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Ni Zn Bi Sn Pb Others Al
0.4-0.8 0.8 3.3-4.6 0.5-1.0 0.4-1.8 0.1 0.2 0.2 0.2 0.2 0.8-1.5 0.30 Rest
Special Characteristics:
Short-chipped - suitable for machining.

Chemical Composition: EN AW-6026 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Ti Bi Pb Others Al
0.6-1.4 0.7 0.2-0.5 0.2-1.0 0.2-1.2 <0.3 <0.3 <0.2 0.5-1.5 <0.4 0.15 Rest
Special Characteristics:
Short-chipped, high corrosion resistance, high strength, suitable for anodizing. To obtain optimal surface when anodizing, it is
recommended to turn min. 0.5 mm up to ø28 mm and 1 mm above that.

Chemical Composition: EN AW-2011 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Bi Pb Others Al
0,4 0,7 5,0-6,0 0,3 0,2-0,6 0,2-0,39 0,15 Rest
Special Characteristics:
Short-chipped, suitable for machining, polished surface, can be protectively anodized.

Chemical Composition: EN AW-2014 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Ti Others Al
0.5-1.2 0.7 3.9-5.0 0.4-1.2 0.2-0.8 0.1 0.25 0.15 0.15 Rest
Special Characteristics:
Short-chipped, suitable for machining, high strength.

Chemical Composition: EN AW-7075 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Ti Others Al
0.4 0.5 1.2-2.0 0.3 2.1-2.9 0.18-0.28 5.1-6.1 0.2 0.15 Rest
Special Characteristics:
Suitable for machining, very high strength.

EN AW - 6082 EN AW - 2007 EN AW - 6026 EN AW - 2011

32
Aluminium Bars - Round
EN 573-3, 754-1, 754-2, 754-3, 755-1, 755-2, 755-3
Diameter Kg/m EN AW-2007 EN AW-2011 EN AW-2014 EN AW-6026 EN AW-6060 EN AW-6082 EN AW-5083 EN AW-5754 EN AW-7075
mm (cut and drill­ (cut and drill­ (cut and drill­ (Corrosion (Corrosion
ing quality) ing quality) ing quality) resistance) resistance)

Length: Length: Length: Length: Length: Length: Length: Length: Length:

3000 mm 3000 mm 3000 mm 3000 mm 6000 mm 3000-6000 mm 3000 mm 3000 mm 3000 mm

3 0.02 * • 1)

4 0.04 * • 1)

5 0.06 * • 1) * • 1)

6 0.08 • 1) *• 1)
*• 1) 2)
* • 1)

7 0.11 • 1) 2)
* • 1) *• 1) 2)

8 0.15 • 1) 2)
• 1) *• 1)
*• 1)
*• 1)

9 0.19 * • 1) * • 1)
10 0.22 • 1) 2)
• 1) * • 1) *• 1)
• 1) 2) *• 1)

12 0.33 • 1) 2)
• 1) • 1) *• 1)
• 2) *• 1)

13 0.38 * • 1)
14 0.44 * • 1) * • 1) *• 1)

15 0.50 • 1) 2)
• 1) • 1) *• 1)
• 1) 2) *• 1)

16 0.58 * • 1) * • 1) • 2) *• 1) 2)

17 0.65 * • 1) * • 1)
18 0.73 • 1) 2)
* • 1) • 1) *• 2)
*• 1) 2)
*• 1)

19 0.81 * • 1)
20 0.89 • 1) 2)
• 1) • 1)
• 1) 2)
*• 1)
• 1) 2)
*• 2)
*• 1) 2)

21 1.00
22 1.08 • 1) 2)
• 1)
• 1)
• 2)
*• 1)

23 1.19
24 1.29 * • 1) • 1)
25 1.38 • 1) 2)
• 1) • 1)
• 1) *• 1)
• 1) 2)
*• 2)
• 1) 2)

26 1.51 * • 1) * • 1)
28 1.76 • 1) * • 1) • 2)
30 1.98 • 1) 2)
• 1) • 1)
• 1) • 1) 2) *• 2)
• 1) 2)

32 2.29 * • 1) • 1) 2) • 2)
33 2.44 * • 1)
34 2.59 • 2) • 1)

35 2.79 • 1) 2) *• 1)
• 1)
• 1)
• 2)
*• 1) 2)

36 2.90 * • 1)
38 3.23 • 2) * • 1) • 1) • 2)
40 3.60 • 1) 2) • 1) • 1)
• 1) 2) • 2) *• 2)
• 1) 2)
42 3.95 * • 1) • 1) * • 2) * • 1) 2)
45 4.60 • 1) 2)
• 1) • 1)
• 1) • 2) • 1) 2)
46 4.74 • 1)
48 5.16 • 1)
50 5.50 • 1) 2) • 1) 2) • 1)
• 1) 2) • 2)
*• 2)
*• 1) 2)
• 1) 2)
55 6.80 • 1) 2) * • 1) 2) • 2)
• 1) 2) • 2)
*• 1) 2)
* • 1) 2)
60 8.05 • 1) 2) * • 1) 2) • 2)
• 1) 2) • 2)
*• 2)
• 2)
65 9.47 • 2) • 2) • 2)
• 2) • 2)
*• 2)
* • 2)
70 10.70 • 2) * • 2) • 2)
• 2) • 2)
*• 2)
• 2)
*Price is dimension dependent. All stated weights are theoretical weights, which may vary.
1)Drawn 2)Extruded 3)Cast (EN AC-) Bars are supplied drawn, extruded or cast.
For bars over 60 mm in diameter the length is 3000 mm for alloy EN AW-6082. More information on page 34.

Please also ask for these alloys:

EN AW-2017. And cut
and drilling quality without lead.

33
Aluminium Bars - Round / Square / Hexagonal

Aluminium Bars - Round

EN 573-3, 755-1, 755-2, 755-3
Diameter Kg/m EN AW-2007 EN AW-2011 EN AW-2014 EN AW-6026 EN AW-6082 EN AW-5083 EN AW-5754 EN AW-7075
mm (cut and drilling (cut and drill­ (cut and drill­ (cut and drill­ (Corrosion (Corrosion
quality) ing quality) ing quality) ing quality) resistance) resistance)

Length: Length: Length: Length: Length: Length: Length: Length:

3000 mm 3000 mm 3000 mm 3000 mm 3000 mm 3000 mm 3000 mm 3000 mm

75 12.60 * • 2)
* • 2)
• 2)
• 2) • 2) * • 2) * • 2)
80 14.20 * • 2)
* • 2)
• 2)
• 2) • 2) * • 2)
*• 2) • 2)
85 16.20 * • 2)
* • 2)
• 2) • 2) * • 2)
* • 2)
90 18.10 * • 2)
* • 2)
• 2) • 2) * • 2)
* • 2)
95 20.20 * • 2)
* • 2)
• 2) • 2) * • 2)
* • 2)
100 22.40 * • 2)
* • 2)
• 2) • 2) * • 2)
*• 2)
• 2)
105 24.70 * • 2)
* • 2)
* • 2) * • 2) * • 2)
110 27.10 * • 2)
* • 2)
• 2) • 2) *• 2)
* • 2)
115 29.60 * • 2)
* • 2)
• 2) * • 2) * • 2)
120 32.10 * • 2)
* • 2)
• 2) • 2) *• 2)
*• 2)
* • 2)
125 35.00 * • 2)
* • 2)
* • 2) * • 2)
130 37.50 * • 2)
* • 2)
• 2) • 2) *• 2)
*• 2)

140 43.80 * • 2)
* • 2)
• 2) • 2) *• 2)
*• 2)

145 47.20
150 50.10 * • 2) *• 2)
• 2)
• 2) *• 2)
*• 2)
* • 2)
160 57.10 * • 2) 3) *• 2)
• 2)
* • 2) *• 2)
• 2)
165 60.90 • 2)
• 2)
170 64.70 *• 2) 3)
*• 2)
* • 2) *• 2)

175 67.30 * • 2)
180 72.50 * • 2) 3) *• 2)
• 2)
• 2) * • 2)
*• 2)
* • 2)
190 81.30 * • 2) 3) * • 2) * • 2)
* • 2)
200 89.50 * • 2) 3) *• 2)
• 2) * • 2)
*• 2)
• 2)
210 98.70 * • 2) 3) • 2) * • 2)

220 108.40 * • 2) 3) * • 2) * • 2)
* • 2)

230 118.40 * • 3) • 2) * • 2)

240 128.90 * • 2) 3) * • 2) 3) * • 2)

250 136.60 * • 2) 3) • 2) 3) *• 2)
* • 2)

260 151.40 * • 2) 3) * • 2) 3) * • 2)

270 157.20 • 2) 3)
280 175.60 * • 2) 3) • 2) 3) *• 2)

300 202.00 * • 2) 3) * • 2) 3) *• 2)

305 208.12 * • 2)
310 215.00 * • 3) * • 2)
320 229.00 * • 2) 3) * • 2) *• 2)

330 244.00 * • 2)
350 274.00 * • 2) 3) * • 2) 3) * • 2)

360 290.00 * • 3) * • 2) 3) * • 2)

380 323.00 * • 3) * • 2) 3) * • 2)

400 358.00 * • 2) 3) * • 2) 3) * • 2)

410 376.00 * • 2)

430 414.00 * • 2)

450 453.00 *• 3)
*• 2) 3)
* • 2)

480 515.00
500 560.00 *• 3)

*Price is dimension dependent.

1)Drawn 2)Extruded 3)Cast (EN AC-) Please also ask for these alloys:
For bars over 60 mm in diameter the length is 3000 mm for alloy EN AW-6082. EN AW-2017, EN AW-2024.
And cut and drilling quality without lead.

34
Aluminium Bars - Square
EN 573-3, 754-1, 754-2, 754-4, 755-1, 755-2, 755-4
mm Kg/m EN AW-2007 EN AW-2011 EN AW-6026 EN AW- EN AW-6082
(cut and drilling quality) (cut and drilling quality)
(cut and drilling quality) 6060/6063
Length: Length: Length: Length:
Length:
3000 mm 3000 mm 6000 mm 3000-6000 mm
3000 mm
8 0.18 • 1) * • 2)
10 0.27 * • 1) • 2)
12 0.39 * • 2)
• 2)
15 0.61 * • 2)
* • 1)
* • 2)
• 2)
20 1.08 * • 2)
* • 1)
• 1)
* • 2)
• 2)
25 1.69 * • 2)
* • 1)
* • 2)
• 2)
30 2.52 * • 2)
* • 1)
• 1)
• 2)
35 3.33 * • 2)
* • 1)
* • 1) • 2)
40 4.48 * • 2)
* • 1)
• 1) 2) • 2)
45 5.47 * • 2)
• 2)
50 6.80 * • 2)
*• 2)
• 1) 2)
• 2)
55 8.20 * • 2)
* • 2)
60 9.72 * • 2)
*• 2)
• 1) 2)
• 2)
65 11.80 *• 2)
* • 2)
70 13.23 *• 2)
*• 2)
• 2) • 2)
75 15.47 * • 2) * • 2)
80 17.30 *• 2)
*• 2)
• 2)
85 20.30 • 2)
90 22.96 *• 2)
*• 2)
• 2)
• 2)
95 24.50 * • 2)
100 27.00 *• 2)
*• 2)
• 2)
• 2)
110 33.00 • 2)
120 39.00 * • 2)
130 47.30 • 2)
135 49.21 * • 2)
140 54.90 • 2)
* • 2)
150 63.00 • 2)
160 69.90 * • 2)
165 77.60 * • 2)
170 82.37 * • 2)
180 90.70 * • 2)
200 112.00 * • 2)
220 131.00 * • 2)
* Price is dimension dependent.
1)Drawn 2)Extruded
For bars over 60 mm the length is 3000 mm for alloy EN AW-6082.

Aluminium Bars - Hexagonal

EN 573-3, 754-1, 754-2, 754-6, 755-1, 755-2, 755-6
mm Kg/m EN AW-2011 EN AW-6026
(cut and drilling quality) (cut and drilling quality)
Length: 3000 mm Length: 3000 mm
8 0.16
10 0.25 *•
14 0.48 *•
17 0.72 *• *•
19 0.89 *•
22 1.20 *• *•
27 1.80 *• *•
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.

35
Aluminium Profiles - Flat

Aluminium Profiles
EN AW-6060 T6 - EN AW-6082 T6
Manufacturing length 6000 mm EN 573-3, 755-1, 755-2, 755-5
WXH kg/m WXH kg/m WXH kg/m
mm mm mm
* 10 x 2 0.06 35 x 5 0.48 60 x 30 4.86
10 x 3 0.09 * 35 x 6 0.60 60 x 40 6.80
* 10 x 4 0.11 * 35 x 8 0.76 * 60 x 50 8.10
* 10 x 5 0.14 35 x 10 0.95 * 70 x 5 0.95
* 10 x 8 0.22 * 35 x 12 1.14 70 x 6 1.14
* 12 x 3 0.10 * 35 x 15 1.42 * 70 x 8 1.53
* 12 x 4 0.13 40 x 2 0.22 70 x 10 1.89
* 12 x 8 0.26 40 x 3 0.33 * 70 x 12 2.27
* 15 x 2 0.09 40 x 4 0.44 70 x 15 2.84
15 x 3 0.13 40 x 5 0.54 70 x 20 3.78
15 x 4 0.17 40 x 6 0.65 70 x 25 4.75
* 15 x 5 0.21 40 x 8 0.87 70 x 30 5.70
* 15 x 6 0.24 40 x 10 1.08 70 x 35 6.80
* 15 x 8 0.33 40 x 12 1.30 70 x 40 7.60
* 15 x 10 0.41 40 x 15 1.62 * 70 x 50 9.71
* 20 x 2 0.11 40 x 20 2.16 75 x 6 1.21
20 x 3 0.17 40 x 25 2.71 75 x 8 1.62
* 20 x 4 0.22 40 x 30 3.24 75 x 10 2.03
20 x 5 0.27 * 45 x 3 0.36 75 x 15 3.10
* 20 x 6 0.33 45 x 5 0.61 75 x 20 4.15
* 20 x 8 0.44 45 x 6 0.73 75 x 25 5.08
20 x 10 0.54 * 45 x 8 0.97 * 75 x 40 8.10
* 20 x 12 0.65 * 45 x 10 1.22 * 80 x 3 0.65
* 20 x 15 0.81 50 x 2 0.27 * 80 x 4 0.87
25 x 2 0.14 50 x 3 0.41 80 x 5 1.08
25 x 3 0.21 50 x 4 0.54 80 x 6 1.30
25 x 4 0.27 50 x 5 0.68 80 x 8 1.73
25 x 5 0.36 50 x 6 0.81 80 x 10 2.16
* 25 x 6 0.41 50 x 8 1.08 80 x 12 2.60
* 25 x 8 0.54 50 x 10 1.35 80 x 15 3.24
25 x 10 0.68 50 x 12 1.62 80 x 20 4.32
25 x 12 0.81 50 x 15 2.05 80 x 10 2.16
25 x 15 1.02 50 x 20 2.70 80 x 15 3.24
* 25 x 20 1.35 50 x 25 3.38 80 x 20 4.32
30 x 2 0.17 50 x 30 4.05 * 80 x 25 5.40
30 x 3 0.25 50 x 40 5.40 80 x 30 6.48
30 x 4 0.33 * 60 x 2 0.32 80 x 40 8.64
30 x 5 0.41 * 60 x 3 0.49 * 80 x 50 10.90
* 30 x 6 0.49 * 60 x 4 0.65 80 x 60 13.00
30 x 8 0.65 60 x 5 0.81 85 x 30 6.89
30 x 10 0.81 60 x 6 0.98 * 90 x 5 1.22
30 x 12 0.98 60 x 8 1.20 90 x 10 2.43
30 x 15 1.22 60 x 10 1.62 * 90 x 20 4.95
30 x 20 1.62 * 60 x 12 1.95 90 x 60 14.58
* 30 x 25 2.03 60 x 15 2.43 * 100 x 3 0.81
* 35 x 3 0.29 60 x 20 3.24 * 100 x 4 1.14
* 35 x 4 0.38 * 60 x 25 4.08 * 100 x 5 1.35
* Price is dimension dependent. More information on page 37.
Profiles with a thickness of more than 10 mm can be supplied in EN AW-6082. All stated weights are theoretical
weights, which may vary.
We stock certain dimensions with DNV-certificate.
36
Aluminium Profiles
EN AW-6060 T6 - EN AW-6082 T6
Manufacturing length 6000 mm EN 573-3, 755-1, 755-2, 755-5
WXH kg/m WXH kg/m WXH kg/m
mm mm mm
100 x 6 1.62 * 120 x 25 8.40 * 150 x 25 10.13
100 x 8 2.16 * 120 x 30 9.72 150 x 30 12.15
100 x 10 2.70 * 120 x 50 16.20 * 160 x 20 8.64
100 x 12 3.24 * 120 x 60 19.50 * 165 x 65 28.96
100 x 15 4.05 * 120 x 70 23.10 180 x 15 7.29
100 x 20 5.40 * 120 x 80 26.00 180 x 20 9.80
100 x 25 7.00 * 125 x 10 3.38 * 180 x 50 24.50
100 x 30 8.10 * 125 x 12 4.05 200 x 10 5.40
* 100 x 35 9.45 * 125 x 15 5.10 200 x 12 6.48
100 x 40 10.80 125 x 40 13.50 200 x 15 8.10
100 x 50 13.50 130 x 50 17.55 200 x 20 10.80
100 x 60 16.20 * 134 x 35 12.91 200 x 25 13.50
100 x 70 18.90 * 140 x 20 7.70 * 200 x 30 16.20
* 100 x 80 22.00 * 140 x 30 11.40 200 x 40 21.90
* 110 x 10 3.00 * 140 x 40 15.20 * 200 x 50 27.00
* 120 x 5 1.62 * 150 x 5 2.02 * 200 x 60 32.40
120 x 8 2.60 * 150 x 8 3.24 220 x 30 17.82
120 x 10 3.24 150 x 10 4.05 * 310 x 20 16.74
120 x 12 3.89 150 x 12 4.86 * 310 x 90 75.33
120 x 15 4.86 150 x 15 6.08
* 120 x 20 6.50 150 x 20 8.10
*Price is dimension dependent.
Profiles with a thickness of more than 10 mm can be supplied in EN AW-6082. All stated weights are theoretical weights, which may vary.
Certain dimensions can also be supplied in alloy EN AW 6012/6026.

We stock certain dimensions with DNV-certificate.

Aluminium Profiles
EN AW-2007
Manufacturing length 3000 mm EN 573-3, 755-1, 755-2, 755-5
WXH kg/m WXH kg/m WXH kg/m
mm mm mm
* 20 x 10 0.56 * 50 x 15 2.07 * 60 x 40 6.72
* 25 x 20 1.38 * 50 x 20 2.80 * 70 x 40 7.84
* 30 x 10 0.84 * 50 x 25 3.50 * 70 x 50 9.80
* 30 x 15 1.26 * 50 x 30 4.20 * 80 x 10 2.24
* 30 x 20 1.68 * 50 x 40 5.60 * 80 x 15 3.36
* 40 x 10 1.12 * 60 x 10 1.68 * 80 x 20 4.48
* 40 x 20 2.24 * 60 x 15 2.52 * 90 x 15 3.92
* 40 x 25 2.70 * 60 x 20 3.36 * 90 x 40 10.08
* 40 x 30 3.36 * 60 x 25 4.28 * 90 x 50 12.61
* 50 x 10 1.40 * 60 x 30 5.04 * 100 x 10 2.80
* 100 x 15 4.05
*Price is dimension dependent.

37
Aluminium Profiles - U / T

Aluminium Profiles - U - EN AW-6060 T6

Manufacturing length 6000 mm
EN 573-3, 755-1, 755-2, 755-9

Even-sided mm kg/m Uneven-sided mm kg/m Uneven-sided mm kg/m

WXHxWxT WXHxWxT WXHxWxT
10 x 10 x 10 x 1.5 0.11 20 x 10 x 20 x 2 0.25 30 x 50 x 30 x 4 1.11
* 10 x 10 x 10 x 2 0.15 * 20 x 15 x 20 x 2 0.28 * 30 x 50 x 30 x 5 1.35
12 x 12 x 12 x 2 0.20 10 x 20 x 10 x 2 0.20 * 40 x 50 x 40 x 4 1.41
* 14 x 14 x 14 x 2 0.22 * 15 x 20 x 15 x 2 0.25 * 30 x 60 x 30 x 3 0.96
15 x 15 x 15 x 2 0.23 * 30 x 20 x 30 x 2 0.43 * 30 x 60 x 30 x 4 1.27
20 x 20 x 20 x 2 0.32 * 40 x 20 x 40 x 2 0.52 * 40 x 60 x 40 x 3 1.14
* 20 x 20 x 20 x 3 0.43 15 x 25 x 15 x 2 0.29 * 40 x 60 x 40 x 4 1.52
* 25 x 25 x 25 x 2 0.40 * 15 x 30 x 15 x 2 0.30 40 x 60 x 40 x 5 1.78
25 x 25 x 25 x 3 0.59 * 15 x 30 x 15 x 3 0.45 * 40 x 70 x 40 x 4 1.54
* 30 x 30 x 30 x 2 0.49 * 20 x 30 x 20 x 2 0.36 * 30 x 80 x 30 x 3 1.10
30 x 30 x 30 x 3 0.72 20 x 30 x 20 x 3 0.54 * 40 x 80 x 40 x 3 1.25
* 30 x 30 x 30 x 4 0.88 * 40 x 30 x 40 x 3 0.87 * 40 x 80 x 40 x 4 1.64
* 35 x 35 x 35 x 3 0.80 * 20 x 35 x 20 x 2 0.39 40 x 80 x 40 x 5 2.03
* 40 x 40 x 40 x 2 0.62 * 20 x 40 x 20 x 2 0.51 * 50 x 80 x 50 x 5 2.30
40 x 40 x 40 x 3 0.93 * 20 x 40 x 20 x 3 0.63 * 40 x 100 x 40 x 3 1.42
* 40 x 40 x 40 x 4 1.21 25 x 40 x 25 x 3 0.72 * 40 x 100 x 40 x 4 1.87
* 50 x 50 x 50 x 3 1.22 * 30 x 40 x 30 x 3 0.79 * 50 x 100 x 50 x 3 1.58
* 50 x 50 x 50 x 4 1.54 * 30 x 40 x 30 x 4 0.99 50 x 100 x 50 x 5 2.58
* 50 x 50 x 50 x 5 1.90 * 25 x 45 x 25 x 3 0.73 * 50 x 100 x 50 x 8 x 6 x 8 3.53
* 60 x 60 x 60 x 4 1.86 * 20 x 50 x 20 x 3 0.73 * 55 x 120 x 55 x 10 5.70
* 60 x 60 x 60 x 5 2.29 * 25 x 50 x 25 x 4 1.00 60 x 120 x 60 x 5 3.12
30 x 50 x 30 x 3 0.90 * 100 x 200 x 100 x 10 10.30
* Price is dimension dependent.

Aluminium T-profiles - EN AW-6060 T6 - EN AW-6082 T6

Manufacturing length 6000 mm
EN 573-3, 755-1, 755-2, 755-9

Even-sided mm kg/m Even-sided mm kg/m Uneven-sided mm kg/m

HxWxT HxWxT HxWxT
20 x 20 x 2 0.21 * 50 x 50 x 3 0.79 * 50 x 30 x 5 1.02
* 25 x 25 x 2 0.26 * 50 x 50 x 4 1.04 * 100 x 50 x 6 2.34
* 25 x 25 x 3 0.39 50 x 50 x 5 1.27
30 x 30 x 3 0.47 * 60 x 60 x 4 1.30
* 40 x 40 x 3 0.63 60 x 60 x 6 1.90
40 x 40 x 4 0.82 80 x 80 x 8 3.35
* Price is dimension dependent.

38
Aluminium Profiles - Angle

Aluminium Profiles - EN AW-6060 T6 - EN AW-6082 T6

Manufacturing length 6000 mm. EN 573-3, 755-1, 755-2, 755-9
Even-sided mm kg/m Uneven-sided mm kg/m Uneven-sided mm kg/m
WxHxT WxHxT WxHxT
* 10 x 10 x 2 0.10 15 x 10 x 2 0.13 * 60 x 40 x 4 1.04
15 x 15 x 2 0.16 20 x 10 x 2 0.16 60 x 40 x 5 1.30
15 x 15 x 3 0.22 * 20 x 10 x 3 0.25 * 60 x 40 x 6 1.53
20 x 20 x 2 0.21 20 x 15 x 2 0.18 * 60 x 50 x 2 0.59
20 x 20 x 3 0.30 25 x 10 x 2 0.18 * 65 x 50 x 5 1.49
* 20 x 20 x 4 0.42 * 25 x 15 x 2 0.21 * 65 x 50 x 6 1.78
25 x 25 x 2 0.26 * 25 x 15 x 3 0.30 * 70 x 20 x 2 0.49
25 x 25 x 3 0.38 * 25 x 20 x 2 0.24 * 70 x 20 x 3 0.71
* 25 x 25 x 4 0.50 * 25 x 20 x 3 0.35 * 70 x 25 x 2.5 0.63
25 x 25 x 5 0.64 * 30 x 10 x 2 0.21 * 70 x 30 x 2 0.53
30 x 30 x 2 0.32 * 30 x 15 x 2 0.24 * 70 x 50 x 5 1.68
30 x 30 x 3 0.47 * 30 x 15 x 3 0.35 * 75 x 50 x 5 1.68
30 x 30 x 4 0.61 * 30 x 15 x 4 0.45 * 75 x 50 x 6 1.93
30 x 30 x 5 0.74 * 30 x 20 x 2 0.26 * 75 x 50 x 7 2.25
35 x 35 x 3 0.55 30 x 20 x 3 0.39 75 x 50 x 8 2.60
35 x 35 x 4 0.72 * 30 x 25 x 2 0.29 * 80 x 15 x 2 0.51
* 35 x 35 x 5 0.89 * 30 x 25 x 3 0.43 * 80 x 20 x 2 0.55
* 40 x 40 x 2 0.43 * 35 x 20 x 3 0.43 * 80 x 30 x 3 0.90
* 40 x 40 x 3 0.65 * 35 x 25 x 2 0.31 * 80 x 40 x 3 0.99
40 x 40 x 4 0.83 * 35 x 30 x 3 0.51 * 80 x 40 x 4 1.26
40 x 40 x 5 1.02 * 40 x 10 x 2 0.26 * 80 x 40 x 5 1.63
* 40 x 40 x 6 1.19 * 40 x 15 x 2 0.29 * 80 x 40 x 6 1.85
* 45 x 45 x 3 0.71 40 x 20 x 2 0.32 * 80 x 50 x 5 1.76
* 45 x 45 x 5 1.22 * 40 x 20 x 3 0.47 80 x 50 x 6 2.01
* 50 x 50 x 2 0.53 * 40 x 20 x 4 0.61 * 90 x 50 x 6 2.20
50 x 50 x 3 0.79 * 40 x 25 x 2 0.35 * 100 x 20 x 2 0.63
* 50 x 50 x 4 1.04 40 x 25 x 3 0.51 * 100 x 30 x 3 1.02
50 x 50 x 5 1.29 * 40 x 25 x 4 0.68 100 x 40 x 4 1.47
50 x 50 x 6 1.52 * 40 x 25 x 5 0.83 100 x 50 x 3 1.24
* 50 x 50 x 8 1.99 * 40 x 30 x 2 0.37 100 x 50 x 5 1.96
* 50 x 50 x 10 2.43 * 40 x 30 x 3 0.55 100 x 50 x 6 2.34
* 60 x 60 x 2 0.65 * 40 x 30 x 4 0.73 100 x 50 x 7 2.80
* 60 x 60 x 3 0.98 * 40 x 30 x 5 0.88 * 100 x 50 x 8 3.07
* 60 x 60 x 4 1.26 * 45 x 30 x 1.5 0.31 * 100 x 50 x 10 3.79
* 60 x 60 x 5 1.58 * 50 x 15 x 2 0.36 * 100 x 60 x 4 1.73
60 x 60 x 6 1.85 * 50 x 20 x 2 0.37 * 100 x 60 x 6 2.50
* 60 x 60 x 8 2.52 * 50 x 20 x 3 0.55 * 100 x 65 x 8 3.44
* 60 x 60 x 10 2.97 50 x 25 x 2 0.40 * 100 x 65 x 9 3.81
* 70 x 70 x 5 1.83 * 50 x 25 x 3 0.60 * 100 x 75 x 6 2.84
* 70 x 70 x 6 2.18 * 50 x 25 x 4 0.77 * 100 x 75 x 8 3.61
* 70 x 70 x 7 2.52 * 50 x 25 x 5 0.96 * 120 x 40 x 4 1.75
* 75 x 75 x 5 1.96 * 50 x 30 x 2 0.43 * 120 x 50 x 5 2.22
* 75 x 75 x 8 3.11 * 50 x 30 x 3 0.63 * 120 x 60 x 6 2.83
* 75 x 75 x 9 3.50 50 x 30 x 4 0.84 * 120 x 80 x 10 5.15
* 75 x 75 x 10 4.00 50 x 30 x 5 1.02 * 125 x 80 x 8 4.27
* 80 x 80 x 3 1.27 * 50 x 40 x 4 0.93 * 130 x 65 x 8 4.05
* 80 x 80 x 4 1.68 * 50 x 40 x 5 1.15 130 x 65 x 10 5.27
* 80 x 80 x 5 2.14 * 60 x 15 x 2 0.40 * 130 x 75 x 9 4.77
* 80 x 80 x 6 2.50 * 60 x 20 x 2 0.44 * 130 x 80 x 6 3.33
80 x 80 x 8 3.29 * 60 x 25 x 3 0.66 * 150 x 50 x 5 2.63
* 80 x 80 x 10 4.05 * 60 x 30 x 2 0.48 150 x 75 x 8 4.70
* 100 x 100 x 4 2.11 * 60 x 30 x 3 0.71 * 150 x 75 x 9 5.26
* 100 x 100 x 5 2.70 * 60 x 30 x 4 0.93 * 150 x 100 x 10 6.60
* 100 x 100 x 6 3.24 * 60 x 30 x 5 1.20 * 200 x 100 x 10 8.22
100 x 100 x 10 5.13 * 60 x 40 x 2 0.54
60 x 40 x 3 0.79
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.

We stock certain dimensions with DNV-certificate.

39
Aluminium Tubes - Square / Rectangular

Aluminium Tubes - Square - EN AW-6060 - T6 EN AW-6063 T6

Length: 6000mm EN 573-3, 755-1, 755-2, 755-7, 755-8
mm kg/m mm kg/m mm kg/m mm kg/m
10 x 10 x 1.0 0.10 *R 30 x 30 x 2.0 0.61 * 60 x 60 x 2.0 1.30 * 150 x 150 x 5.0 7.90
12 x 12 x 1.0 0.12 30 x 30 x 3.0 0.88 * R 60 x 60 x 3.5 2.10
* 15 x 15 x 1.5 0.23 40 x 40 x 2.0 0.83 * 60 x 60 x 4.0 2.42
15 x 15 x 2.0 0.32 * R 40 x 40 x 2.5 1.05 70 x 70 x 2.0 1.50
* 16 x 16 x 1.5 0.24 * R 40 x 40 x 3.0 1.19 * 70 x 70 x 4.0 2.86
18 x 18 x 1.0 0.20 * R 40 x 40 x 4.0 1.56 80 x 80 x 3.0 2.50
20 x 20 x 1.0 0.21 45 x 45 x 2.0 0.93 * 80 x 80 x 4.0 3.30
20 x 20 x 1.5 0.30 * 50 x 50 x 2.0 1.05 * R 80 x 80 x 5.0 4.25
20 x 20 x 2.0 0.39 R 50 x 50 x 2.5 1.30 90 x 90 x 4.0 3.78
25 x 25 x 1.5 0.38 50 x 50 x 3.0 1.54 * 100 x 100 x 2.0 2.16
20 x 20 x 2.0 0.39 * R 50 x 50 x 4.0 1.99 *R 100 x 100 x 4.0 4.15
25 x 25 x 1.5 0.38 50 x 50 x 5.0 2.43 100 x 100 x 5.0 5.19
*R 25 x 25 x 2.0 0.52 * 55 x 55 x 2.0 1.15 * 100 x 100 x 10.0 9.85
* 25 x 25 x 3.0 0.72 * R 60 x 60 x 1.8 1.10 * 120 x 120 x 5.0 6.40
* Price is dimension dependent.
R) Also supplied with corner radius. Price on request. R = Corner radius
Length for profiles with corner radius, ask Alumeco.

Aluminium Tubes - Rectangular - EN AW-6060 T6

Length: 6000mm EN 573-3, 755-1, 755-2, 755-7, 755-8
mm kg/m mm kg/m mm kg/m

20 x 10 x 1.5 0.24 * 60 x 20 x 2.0 0.83 * 100 x 50 x 4.0 3.07

* 20 x 10 x 2.0 0.29 * 60 x 25 x 3.0 1.29 * 100 x 50 x 5.0 3.78
* 20 x 15 x 2.0 0.35 * 60 x 30 x 2.0 0.93 * 100 x 60 x 3.0 2.50
25 x 15 x 2.0 0.40 * 60 x 30 x 3.0 1.36 * 100 x 60 x 4.0 3.40
* 25 x 20 x 2.0 0.45 * 60 x 40 x 2.0 1.04 * 100 x 80 x 3.0 2.89
* 30 x 15 x 2.0 0.46 60 x 40 x 2.5 1.30 * 120 x 18 x 2.0 1.46
R 30 x 20 x 2.0 0.50 * 60 x 40 x 3.0 1.60 * 120 x 20 x 2.0 1.54
* 30 x 25 x 2.0 0.56 60 x 40 x 4.0 1.99 * 120 x 30 x 3.0 2.43
* 35 x 20 x 2.0 0.56 * 60 x 50 x 3.0 1.70 * 120 x 40 x 2.0 1.69
* 35 x 25 x 2.0 0.61 * 70 x 20 x 2.0 0.92 * 120 x 40 x 3.0 2.49
* 40 x 15 x 2.0 0.56 * 80 x 20 x 2.0 1.08 * 120 x 40 x 4.0 3.29
40 x 20 x 1.5 0.46 * 80 x 30 x 2.0 1.15 * 120 x 50 x 4.0 3.64
40 x 20 x 2.0 0.61 * 80 x 30 x 3.0 1.71 * 120 x 60 x 2.5 2.37
* 40 x 20 x 2.5 0.81 * 80 x 40 x 2.0 1.28 * 120 x 60 x 3.0 2.81
* 40 x 20 x 3.0 0.88 80 x 40 x 3.0 1.85 * 120 x 60 x 4.0 3.70
40 x 25 x 2.0 0.66 * 80 x 40 x 4.0 2.40 * 140 x 50 x 4.0 3.73
* 40 x 30 x 2.0 0.72 * R 80 x 50 x 3.0 2.00 * 150 x 40 x 4.0 3.92
* 40 x 30 x 3.0 1.12 * 80 x 50 x 4.0 2.64 150 x 50 x 3.0 3.14
* 50 x 15 x 2.0 0.66 * 80 x 60 x 4.0 3.03 * 150 x 50 x 4.0 4.15
50 x 20 x 2.0 0.72 * 90 x 30 x 2.5 1.55 * R 150 x 50 x 5.0 5.15
* 50 x 25 x 2.0 0.80 100 x 18 x 2.0 1.24 * 150 x 100 x 3.0 3.95
* 50 x 25 x 3.0 1.19 100 x 20 x 2.0 1.26 * 160 x 40 x 4.0 4.20
50 x 30 x 2.0 0.83 * 100 x 25 x 1.5 1.00 * 180 x 40 x 4.0 4.58
50 x 30 x 2.5 1.10 * 100 x 30 x 3.0 2.18 * 200 x 50 x 4.0 5.25
50 x 30 x 3.0 1.20 * 100 x 40 x 2.0 1.50 * 200 x 100 x 4.0 6.48
* 50 x 34 x 2.5 1.15 100 x 40 x 2.5 1.90 * 200 x 100 x 5.0 7.83
* 50 x 40 x 2.0 0.96 * 100 x 40 x 3.0 2.28
* 50 x 40 x 2.5 1.20 * 100 x 40 x 4.0 2.94
* 50 x 40 x 3.0 1.54 * 100 x 50 x 2.0 1.60
* 50 x 40 x 4.0 1.78 100 x 50 x 3.0 2.36
Length for profiles with corner radius, ask Alumeco. R = Corner radius
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.

Other dimensions can be supplied subject to inquiry.

40
Aluminium Profiles - Anodized

Aluminium Profiles nature anodized with E6/20 microns EN AW-6060 T6

Manufacturing length 6000 mm. EN 573-3, 755-1, 755-2, 755-7, 755-8, 755-9

Profile anodizing

WxHxT kg/m WxHxT kg/m WxHxWxT kg/m

Even-sided mm Even-sided mm Even-sided mm
15 x 15 x 2 0.16 20 x 20 x 1 0.21 10 x 20 x 10 x 2 0.20
20 x 20 x 2 0.21 20 x 20 x 2 0.39 15 x 15 x 15 x 2 0.23
25 x 25 x 2 0.26 25 x 25 x 2 0.52 20 x 20 x 20 x 2 0.32
30 x 30 x 2 0.32 30 x 30 x 2 0.61 20 x 40 x 20 x 2 0.51
30 x 30 x 3 0.46 40 x 20 x 2 0.61 25 x 25 x 25 x 2 0.40
35 x 35 x 3 0.55 40 x 40 x 2 0.83 40 x 20 x 40 x 2 0.52
40 x 40 x 2 0.43 40 x 40 x 4 1.60
70 x 20 x 2 0.92

41
Aluminium Profiles - Bulb / Aluminium Tubes - Round

Aluminium Profiles - Bulb

EN AW-6082 T6 - EN AW-5083 H112
Manufacturing lengths 5000 - 6000 mm
EN 573-3, 755-1, 755-2, 755-9
Dimension H x S kg/m C1 C2 C2
60 x 5.0 1.24 15 10
65 x 3.5 1.23 15 15 C1

75 x 4.0 1.60 17 17
85 x 4.5 2.02 19 19 S
H
120 x 5.0 3.60 27 27
140 x 6.0 4.72 30 30
180 x 7.0 7.80 40 40
Not in stock. All stated weights are theoretical weights, which may vary.

Aluminium Tubes - Round D

EN AW-6060 T6 - EN AW-6005A T6 / EN AW-6082 T6
Manufacturing length 6000 mm
EN-573-3, 755-1, 755-2, 755-7, 755-8
mm kg/m mm kg/m mm kg/m
OD x t OD x t OD x t
6.0 x 1.0 0.05 * 22.0 x 2.0 0.40 * 40.0 x 2.0 0.65
8.0 x 1.0 0.06 * 22.0 x 3.0 0.48 * 40.0 x 2.5 0.79
10.0 x 1.0 0.08 25.0 x 1.0 0.21 40.0 x 3.0 0.95
* 10.0 x 1.5 0.11 25.0 x 1.5 0.30 * 40.0 x 3.5 1.09
* 10.0 x 2.0 0.14 25.0 x 2.0 0.39 * 40.0 x 4.0 1.23
12.0 x 1.0 0.10 25.0 x 2.5 0.47 40.0 x 5.0 1.49
* 12.0 x 1.5 0.14 25.0 x 3.0 0.57 40.0 x 7.5 2.07
* 12.0 x 2.0 0.17 * 25.0 x 3.5 0.64 * 42.0 x 2.5 0.85
* 13.0 x 1.5 0.16 * 25.0 x 5.0 0.85 * 42.0 x 3.0 1.00
* 14.0 x 3.0 0.28 28.0 x 1.5 0.34 * 42.0 x 3.5 1.15
* 15.0 x 1.0 0.12 30.0 x 2.0 0.48 * 42.0 x 5.0 1.60
15.0 x 1.5 0.18 * 30.0 x 2.5 0.59 45.0 x 2.0 0.74
* 15.0 x 2.0 0.23 30.0 x 3.0 0.69 * 45.0 x 3.0 1.17
16.0 x 1.5 0.19 * 30.0 x 4.0 0.89 45.0 x 5.0 1.70
* 16.0 x 2.0 0.25 * 30.0 x 5.0 1.07 * 48.0 x 2.5 0.99
* 16.0 x 3.0 0.34 * 30.0 x 6.0 1.38 * 48.0 x 3.0 1.15
18.0 x 1.0 0.15 * 32.0 x 1.5 0.41 * 48.3 x 4.0 1.53
* 18.0 x 1.2 0.18 * 32.0 x 2.0 0.51 50.0 x 1.5 0.62
18.0 x 1.5 0.21 * 32.0 x 3.0 0.73 50.0 x 2.0 0.82
* 18.0 x 2.0 0.28 * 32.0 x 3.5 0.85 * 50.0 x 2.5 1.00
* 19.0 x 1.0 0.16 35.0 x 1.5 0.43 * 50.0 x 3.0 1.20
19.0 x 1.5 0.23 35.0 x 2.0 0.56 * 50.0 x 3.5 1.39
* 19.0 x 2.0 0.31 * 35.0 x 2.5 0.74 * 50.0 x 4.0 1.57
20.0 x 1.0 0.16 * 35.0 x 3.0 0.82 50.0 x 5.0 1.91
20.0 x 1.5 0.24 * 35.0 x 5.0 1.28 * 50.0 x 10.0 3.81
* 20.0 x 2.0 0.31 * 36.0 x 4.0 1.08 * 50.0 x 12.0 3.90
20.0 x 3.0 0.44 * 38.0 x 1.5 0.47 * 50.0 x 15.0 4.45
* 20.0 x 4.0 0.54 * 38.0 x 3.0 0.89 54.0 x 2.0 0.89
* 20.0 x 5.0 0.64 * 38.0 x 4.0 1.16 * 55.0 x 2.0 0.90
22.0 x 1.5 0.27 40.0 x 1.5 0.49
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.
More information on page 43.

42
Aluminium Tubes - Round D
EN AW-6060 T6 - EN AW-6005A T6 / EN AW-6082 T6
Manufacturing length 6000 mm
EN 573-3, 755-1, 755-2, 755-7, 755-8
mm kg/m mm kg/m mm kg/m
OD x t OD x t OD x t
* 55.0 x 2.5 1.17 90.0 x 5.0 3.61 * 150.0 x 8.0 9.66
* 55.0 x 5.0 2.27 * 90.0 x 10.0 7.25 * 150.0 x 10.0 12.40
* 60.0 x 1.5 0.78 * 90.0 x 20.0 11.80 * 150.0 x 15.0 17.20
* 60.0 x 2.0 0.99 * 96.0 x 3.0 2.37 * 150.0 x 20.0 22.50
* 60.0 x 2.5 1.30 100.0 x 2.0 1.70 * 160.0 x 5.0 6.60
60.0 x 3.0 1.46 * 100.0 x 3.0 2.47 * 160.0 x 15.0 18.50
* 60.0 x 4.0 1.90 * 100.0 x 4.0 3.30 * 160.0 x 20.0 24.17
60.0 x 5.0 2.40 100.0 x 5.0 4.04 * 164.0 x 7.0 9.40
* 60.0 x 6.0 2.94 * 100.0 x 6.0 5.01 * 170.0 x 10.0 13.81
* 60.0 x 10.0 4.67 * 100.0 x 10.0 7.65 * 170.0 x 15.0 20.00
* 60.0 x 15.0 6.12 * 100.0 x 15.0 10.86 * 175.0 x 7.0 9.99
* 63.0 x 1.5 0.79 * 100.0 x 16.0 11.43 * 180.0 x 10.0 15.11
* 65.0 x 5.0 2.55 * 100.0 x 20.0 13.90 * 180.0 x 20.0 27.50
* 65.0 x 10.0 5.52 * 100.0 x 30.0 18.13 * 180.0 x 40.0 48.00
* 70.0 x 2.0 1.16 * 102.0 x 1.7 1.48 * 190.0 x 10.0 16.07
* 70.0 x 3.0 1.71 * 106.0 x 3.0 2.73 * 190.0 x 15.0 23.50
* 70.0 x 4.0 2.39 110.0 x 2.0 1.83 * 200.0 x 5.0 8.30
70.0 x 5.0 2.76 110.0 x 5.0 4.50 200.0 x 8.0 14.40
* 70.0 x 10.0 5.19 * 110.0 x 10.0 8.93 * 200.0 x 10.0 16.20
75.0 x 3.0 1.85 120.0 x 5.0 4.90 * 200.0 x 15.0 23.96
75.0 x 5.0 3.02 * 120.0 x 10.0 9.82 * 200.0 x 20.0 31.50
* 75.0 x 10.0 5.51 * 120.0 x 15.0 13.60 * 206.0 x 3.0 5.50
* 76.0 x 3.0 1.90 * 120.0 x 20.0 16.96 * 210.0 x 5.0 8.69
* 80.0 x 2.0 1.33 * 125.0 x 4.0 4.12 * 210.0 x 10.0 16.99
* 80.0 x 3.0 1.96 * 125.0 x 7.5 7.50 * 216.0 x 8.0 14.37
* 80.0 x 4.0 2.58 * 130.0 x 3.0 3.35 * 230.0 x 10.0 18.70
80.0 x 5.0 3.18 * 130.0 x 5.0 5.31 * 240.0 x 10.0 19.90
* 80.0 x 10.0 5.95 * 130.0 x 10.0 10.84 * 250.0 x 5.0 10.80
* 80.0 x 15.0 8.27 * 140.0 x 5.0 5.72 * 250.0 x 10.0 20.40
* 80.0 x 20.0 10.22 * 140.0 x 10.0 11.05 * 260.0 x 10.0 21.25
* 86.0 x 3.0 2.11 * 140.0 x 20.0 20.43 * 266.0 x 8.0 17.70
* 90.0 x 3.0 2.22 * 150.0 x 3.0 3.74 * 318.0 x 9.0 23.60
* 90.0 x 4.0 2.91 150.0 x 5.0 6.18
* Price is dimension dependent. All stated weights are theoretical weights, which may vary.

Other dimensions can be supplied subject to inquiry.

Please also ask for these alloys: EN AW-5754, EN AW-5083, EN AW-6012, EN AW- 2007

43
Aluminium - Roller Tubes

Chemical Composition: EN AW-6060 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.3-0.6 0.1-0.3 0.1 0.1 0.35-0.6 0.05 0.15 0.15 Rest

Roller Tubes Roller Tubes Roller Tubes

T.O.P.-quality: H.T.-quality: I.S.Q.-quality:
Material 6060 Material 6060 Material 6060

Temper-hardened Temper-hardened Temper-hardened

Strength T6 Strength T6 Strength T6

Type: Type : Type :

Hot-extruded via chamber Hot-extruded via chamber Hot-extruded via chamber
mould and drawn

Tolerances: Tolerances: Tolerances:

Outside diameter ISO k 13 Outside diameter ISO k 15 Outside diameter ISO k 14
Inside diameter ISO H 11 Inside diameter ISO M 15 Inside diameter ISO H 14
Inequality of wall in % of Inequality of wall in % of Inequality of wall in % of
the nominal wall thickness the nominal wall thickness the nominal wall thickness
S < 7 mm 6% S > 10 mm 5% S < 10 mm 5%
S > 7 mm 5%

Straightness: 0.2 mm/m Straightness: 0.5 mm/m Straightness:

D < 250 mm 0.6 mm
D > 250 mm 0.8 mm/m

Concentric running accuracy Concentric running accuracy Concentric running accuracy

between centres: between centres: between centres:
Max: 0.4 mm/m Max: 1.0 mm/m D < 250 mm 1.2 mm/m
D > 250 mm 1.6 mm/m

Economy and quality:

High quality roller tubes - a necessity for economical production. Fine tolerances on outside and inside diameters,
uniform thickness and concentric running accuracy help to optimise the production process and reduce material
consumption.

Additional technical and economical benefits: Quality example: Roller tube in T.O.P.-quality.
• Few tensions Dimensions 120 x 7 x 1800
• Minimal imbalance
• Optimal chipping properties Outside diameter ISO k 13
• Low inertia force Inside diameter ISO H 11
• Highly anodizable Hight of arch, max: 0.36 mm
• High durability Concentric running accuracy
between centres, max: 0.72 mm
Inequality of wall, max: 0.35 mm

44
Roller Tubes - EN AW-6060 T6 D
Manufacturing length 6010 mm
EN 755-1, 755-2

OD x t mm kg/m Quality OD x t mm kg/m Quality OD x t mm kg/m Quality

30 x 4.0 0.90 T.O.P. 110 x 15.0 12.30 H.T. 170 x 20.0 26.00 H.T.
40 x 4.0 1.20 T.O.P. 110 x 20.0 15.60 H.T. 180 x 5.0 7.60 T.O.P.
40 x 6.0 1.80 T.O.P. 110 x 25.0 18.40 H.T. 180 x 8.0 11.90 T.O.P.
50 x 3.0 1.20 T.O.P. 114 x 10.0 9.00 T.O.P. 180 x 10.0 14.70 T.O.P.
50 x 5.0 1.90 T.O.P. 120 x 5.0 5.00 T.O.P. 180 x 15.0 21.40 H.T.
50 x 8.0 2.90 T.O.P. 120 x 7.0 6.80 T.O.P. 180 x 20.0 27.70 H.T.
50 x 10.0 3.50 T.O.P. 120 x 8.0 7.80 T.O.P. 182 x 11.0 16.30 T.O.P.
60 x 2.0 1.00 T.O.P. 120 x 10.0 9.50 T.O.P. 190 x 5.0 8.00 T.O.P.
60 x 3.0 1.50 T.O.P. 120 x 15.0 13.60 H.T. 190 x 10.0 15.60 T.O.P.
60 x 5.0 2.40 T.O.P. 120 x 20.0 17.30 H.T. 190 x 15.0 22.70 T.O.P.
60 x 6.0 2.80 T.O.P. 125 x 10.0 9.90 T.O.P. 195 x 12.5 19.70 I.S.Q.
60 x 7.5 3.40 T.O.P. 128 x 4.0 4.30 T.O.P. 200 x 10.0 16.40 T.O.P.
60 x 10.0 4.30 T.O.P. 130 x 5.0 5.40 T.O.P. 200 x 12.5 20.30 T.O.P.
60 x 15.0 5.80 H.T. 130 x 7.0 7.40 T.O.P. 200 x 15.0 24.00 I.S.Q.
62 x 6.0 2.90 T.O.P. 130 x 10.0 10.40 T.O.P. 200 x 25.0 37.90 I.S.Q.
70 x 3.0 1.70 T.O.P. 130 x 15.0 14.90 T.O.P. 205 x 12.5 20.80 H.T.
70 x 5.0 2.80 T.O.P. 130 x 20.0 19.00 H.T. 210 x 10.0 17.30 I.S.Q.
70 x 8.0 4.30 T.O.P. 132 x 8.5 9.10 T.O.P. 210 x 15.0 25.30 I.S.Q.
70 x 10.0 5.20 T.O.P. 140 x 5.0 5.80 T.O.P. 210 x 20.0 32.90 I.S.Q.
75 x 7.0 4.10 T.O.P. 140 x 7.0 8.10 T.O.P. 220 x 10.0 18.20 I.S.Q.
75 x 10.0 5.60 T.O.P. 140 x 10.0 11.20 T.O.P. 220 x 15.0 26.60 I.S.Q.
80 x 3.0 2.00 T.O.P. 140 x 15.0 16.20 H.T. 225 x 15.0 27.30 I.S.Q.
80 x 5.0 3.20 T.O.P. 140 x 20.0 20.80 H.T. 230 x 15.0 27.90 I.S.Q.
80 x 10.0 6.10 T.O.P. 144 x 11.0 12.70 T.O.P. 240 x 10.0 19.90 I.S.Q.
80 x 15.0 8.40 H.T. 150 x 5.0 6.30 T.O.P. 240 x 15.0 29.20 I.S.Q.
80 x 20.0 10.40 H.T. 150 x 7.5 9.20 T.O.P. 250 x 10.0 20.80 I.S.Q.
81x 8.0 5.10 T.O.P. 150 x 10.0 12.10 T.O.P. 250 x 15.0 30.50 I.S.Q.
90 x 6.0 4.40 T.O.P. 150 x 15.0 17.50 T.O.P. 260 x 15.0 31.80 I.S.Q.
90 x 10.0 6.90 T.O.P. 150 x 20.0 22.50 H.T. 270 x 17.5 38.20 I.S.Q.
90 x 15.0 9.70 H.T. 152 x 6.0 7.60 T.O.P. 285 x 12.5 29.50 I.S.Q.
90 x 20.0 12.10 H.T. 152 x 10.0 12.30 T.O.P. 285 x 20.0 45.90 I.S.Q.
100 x 5.0 4.10 T.O.P. 160 x 5.0 6.70 T.O.P. 285 x 26.0 58.50 I.S.Q.
100 x 6.0 4.90 T.O.P. 160 x 8.0 10.50 T.O.P. 300 x 10.0 25.10 I.S.Q.
100 x 10.0 7.80 T.O.P. 160 x 10.0 13.00 T.O.P. 303 x 18.0 44.40 I.S.Q.
100 x 15.0 11.00 H.T. 160 x 15.0 18.80 H.T. 310 x 20.0 50,20 I.S.Q.
100 x 20.0 13.80 H.T. 160 x 20.0 24.20 H.T. 325 x 17.0 45.30 I.S.Q.
102 x 8.5 6.90 T.O.P. 170 x 5.0 7.10 T.O.P. 360 x 17.0 50.40 I.S.Q.
106 x 8.0 6.80 T.O.P. 170 x 10.0 13.80 T.O.P. 365 x 25.5 74.90 I.S.Q.
110 x 5.0 4.50 T.O.P. 170 x 12.0 16.40 T.O.P.
110 x 10.0 8.70 T.O.P. 170 x 15.0 20.10 H.T.
Can also be supplied cut to length. All stated weights are theoretical weights, which may vary.

Please allow approx. 1-2 weeks’ delivery time for dimensions not in stock.

45
Aluminium - Cylinder Tubes

Chemical Composition: EN AW-6060 - EN 573-3: 2009

Si Fe Cu Mn Mg Cr Zn Others Al

0.3-0.6 0.1-0.3 0.1 0.1 0.35-0.6 0.05 0.15 0.15 Rest

Specification Cylinder tubes for Additional technical

any use data and benefits
Aluminium cylinder tubes:

Alloy: EN AW 6060 T6 • Nominal width 20-320 mm • High wear resistance

• Wall thickness 1.5-10 mm • Fine tolerances
Inside • Length up to 6000 mm • High quality surface
Ø tolerance: ISO H11 • Excellent low friction properties
Roughness: Ra < 1 micron • Aluminium Cylinder tubes of • Lightweight
high precision are always in stock • Pressure and corrosion resistant
Surface: Fine-drawn,
no covering A technically extensive, high qual­
Surface: Fine-drawn, ity range includes different for­
internally and mats to meet individual problem
externally hard solutions.

Layer thickness: • Chamber-pressed

25 microns • Chamber-pressed and drawn
± 5 microns • Piercing-pressed and drawn
Strength: 450 HV • Non-covered
• Hard anodized
Straightness: 0.35 mm per m

Wear - resistance Wall thickness under constant load

100000 180
Diameter (mm)

Hard anodized Galvanized 150

tempered chromium W
al
lt
hi
ck
ne
50000 100 ss
10
Cyanide 90 m
m
tempered steel 8
80 7
m
m
m
70 6 m
m
5 m
m
60 m
Annealed steel 3. 4 m
5
(105 kp/mm) 50 m m
3 m
2. m
5 m
m
40 m
2
m
1. m
5
m
m
30
25
10000
AL 99
Pressure (bar) 6 7 8 9 10 40 50 60 80 100 200 300 400 500 700

5000
Standard values for the definition of the wall thickness on alumin­
ium cylinder tubes, Alloy - 6060, safety to 0.2-limit:2.

2000

0 25 50

Degrading µm

Profitability and quality

The cylinder tube is a special product in our extensive product range.
Using this product, high precision can be achieved, which means they are often used as control and operating
cylinders.
Prices for special dimensions and formats available on request.

46
 D
Aluminium Cylinder Tubes - EN AW-6060 T6
Manufacturing length 3050 mm
EN 573-3, EN 755-1, 755-2

Nominal size Outside diameter x kg/m Nominal size Outside diameter x kg/m
mm wall thickness mm mm wall thickness mm
12 16 x 2.0 0.24 80 85 x 2.5 1.75
16 20 x 2.0 0.31 86 x 3.0 2.12
20 25 x 2.5 0.48 87 x 3.5 2.48
88 x 4.0 2.85
25 28 x 1.5 0.34
30 x 2.5 0.58 85 89 x 2.0 1.48
32 36 x 2.0 0.58 100 105 x 2.50 2.17
38 x 3.0 0.89 106 x 3.00 2.65
35 40 x 2.5 0.80 100 107 x 3.50 3.07
108 x 4.00 3.55
40 44 x 2.0 0.71
45 x 2.5 0.90 110 116 x 3.00 2.88
46 x 3.0 1.09 125 132 x 3.50 4.85
133 x 4.00 4.38
50 54 x 2.0 0.88
55 x 2.5 1.11 150 160 x 5.00 6.60
56 x 3.0 1.35 160 167 x 3.50 4.85
170 x 5.00 7.00
58 63 x 2.5 1.28
200 210 x 5.00 8.69
63 68 x 2.5 1.39
69 x 3.0 1.68 250 262 x 6.00 13.03
70 75 x 2.5 1,54 300 312 x 6.00 15.60
76 x 3.0 1.86 320 336 x 8.00 22.26

Aluminium Profile Cylinder Tubes EN AW-6060 T6

Manufacturing length 3000 mm EN 573-3, 755-1, 755-2, 755-9
For metric thread
I
A (mm) P B (mm) C (mm) D (mm) F (mm) E (mm) G (mm) H (mm) I (mm) C

32.0 H 11 36.0 32.5 5.35 ±0.15 10.0 0.5 0.3 42.5

40.0 H 11 45.0 38.0 5.35 ±0.15 10.0 0.5 0.5 48.0 R
C 90
50.0 H 11 55.0 46.5 6.65 ±0.15 12.0 0.4 0.3 58.5 A
A
G
∅

63.0 H 11 68.0 56.5 6.65 ±0.15 12.0 0.4 0.3 70.0

DF

80.0 H 12 86.0 72.0 8.75 ±0.15 14.0 0.4 0.4 86.0 ∅ AP

E

∅B
100.0 H 12 106.0 89.0 8.75 ±0.15 15.0 0.5 0.3 107.0 ∅H A

125.0 H 12 132.0 110.0 10.50 ±0.15 17.0 0.5 0.4 133.0

For self-cutting screws

I
A (mm) P B (mm) C (mm) D (mm) F (mm) E (mm) G (mm) H (mm) I (mm) C

32.0 H 11 36.0 32.5 5.40 ±0.20 10.4 0.5 0.3 42.9

R
40.0 H 11 45.0 38.0 5.40 ±0.20 10.4 0.5 0.5 48.4 C 90
A
50.0 H 11 55.0 46.5 7.40 ±0.25 13.5 0.4 0.3 60.0
A
G
∅

63.0 H 11 68.0 56.5 7.40 ±0.25 13.5 0.4 0.3 70.0

DF

80.0 H 12 86.0 72.0 9.25 ±0.15 15.0 0.4 0.4 87.0 ∅ AP

E

∅B
100.0 H 12 106.0 89.0 9.25 ±0.15 16.0 0.5 0.3 106.5 ∅H A

125.0 H 12 132.0 110.0 10.50 ±0.15 17.0 0.5 0.3 133.0

160.0 H 13 170.0 140.0 17.50 ±0.15 25.0 0.5 0.4 172.0

47
Aluminium - Fittings

90° Aluminium Welding Bends - EN AW-5754 - EN AW-6060

EN 573-3, DIN 1725, DIN 2605 (Bauart 3 - Long radius), DIN 2609 - EN 755-1,2,8

Dimension Dimension
90 d1 s a d1 s a
25 x 3.0 27.5 40 x 5.0 38.0
a
30 x 2.5 33.5 50 x 3.0 57.0
30 x 3.0 33.5 50 x 4.0 57.0

s
32 x 3.0 33.5 60 x 3.0 76.0
a
35 x 5.0 33.5 60 x 5.0 72.0
d1
40 x 3.0 45.0 70 x 5.0 82.5
40 x 4.0 45.0 75 x 5 . 0 92.0

We would be pleased to receive your

Dimension Dimension
inquiries for 180° bends as well as dimen­ d1 s a d1 s a
sions not mentioned.
80 x 3.0 110.0 100 x 5.0 133.5
80 x 5.0 95.0 106 x 3.0 142.5
90 x 3.0 114.5 110 x 5.0 142.5
90 x 5.0 114.5 125 x 4.0 181.0
100 x 3.0 133.5 160 x 5.0 216.0

Aluminium Screw Sockets

EN AW-6082 T6 / EN AW 6060 T6 - With Whitworth pipe threads
EN 573-3 DIN 2999

l Dimension Dimension Outside Ø Length

Inch mm d I
1
/4" 8 20 25
d
3
/8" 10 25 30
/2"
1
15 30 35
/4"
3
20 35 40
1" 25 40 45
11/4" 32 50 50
11/2" 40 55 55
2" 50 70 60
21/2" 65 90 70
3" 80 100 75
Aluminium Nipples
EN AW-6082 T6 / EN AW 6060 T6 - With Whitworth pipe threads
EN 573-3, DIN 2999

l Dimension Dimension Outside Ø Length Length

A
Inch mm d I A
1
/4" 8 13 50 20
d
1
/2" 15 22 50 20
3
/4" 20 28 50 20
1" 25 35 60 25
11/4" 32 42 65 25
1 /2"
1
40 50 75 30
2" 50 60 75 30

We can also supply:

Alu. welding collars / Alu. collars / Alu. welding nipples /
Alu. T-pieces / Alu. reductions.

48
Transport systems

• TOP SECTIONS

• BOTTOM SECTIONS

• MIDDLE SECTIONS

• CORNER SECTIONS

• AND MUCH MORE...

Aluminium transport systems

are delivered directly from
stock. For more details please
visit us at www.alumeco.com

49
Aluminium - Cargo Sections

Aluminium Cargo Sections - EN AW-6005A T6

Manufacturing length 6000 mm
EN 573-3, EN 755-1, 755-2, 755-9

Ix = 2868449 mm4 Ix = 168450 mm4

Wx = 42978 mm3 Wx = 8743 mm3
198
Iy = 2868449 mm4 Iy = 3594902 mm4
Wy = 42978 mm3 Wy = 36305 mm3
2,5

Profile 7069 3,3 38 Profile 1517

6,3

Weight per m 8.70 Weight per m 2.45

25,4
133,3
Not in stock Not in stock

Ix = 5110595 mm4 Ix = 74420 mm4

Wx= 67082 mm3 Wx = 5204 mm3
Iy = 5110595 mm4 228,5 Iy = 3857535 mm4
Wy = 67082 mm3 Wy = 33745 mm3

Profile 7235 2 28,5 Profile 7176

7,1

Weight per m 11.20 Weight per m 1.95

33
152,4 Not in stock

Ix = 3410000 mm4
Wx = 51300 mm3 Ix = 42975 mm4
Iy = 3410000 mm4 Wx = 3312 mm3
Wy = 51300 mm3 228,5
Iy = 3963457 mm4
Wy = 34669 mm3
Profile 384-4 3
24
2
Profile 7067
6,5 Weight per m 8.90
41 Weight per m 1.85
133 Not in stock
Not in stock

Ix = 220410  mm4
Wx = 6959  mm3 Ix = 76559 mm4
Iy = 252644 mm4 Wx = 6657 mm3
31,7 Wy = 11406  mm3 210 Iy = 4792458 mm4
Wy = 45642 mm3
6,35 52
Profile 7242 23
4 Profile 7003
Weight per m 2.40
Weight per m 2.98

Ix = 196729 mm4 Ix = 479213 mm4

229,8
Wx = 6493 mm3 Wx = 19169 mm3
25,4 Iy = 170190  mm4 Ix = 9676665 mm4
Wy = 8957 mm3 Wx = 84218 mm3
4,2
6,3 51
50,0
Profile 7071 Profile 42205

Weight per m 2.20 Weight per m 4.40

Not in stock
Not in stock
Can be supplied cut to length.
Ix = 63485 mm4
Wx = 5520 mm3
210 Ix = 3674126 mm4
Wx = 34992 mm3
23
3 Profile 7001

Weight per m 2.30

Not in stock

All stated weights are theoretical weights, which may vary.

50
Aluminium/Steel - Joint Compositions / Aluminium - Strongbacking

Aluminium/Steel Joint Compositions

Dimension: (H x W) H = St + Al + Al Weight pr. m
34 x 24 mm in lengths of 3800 mm (20 + 3 + 10) ca. 4.6 kg
34 x 28 mm in lengths of 3800 mm (20 + 3 + 10) ca. 5.3 kg

Other dimensions on request.

Please note:
1. Do not heat above 300° C
2. Do not bend with a radius
less than 300 mm.

10 Aluminium
AIMg 4,5 Mn

3 3 mm
Aluminium
3 mm
Steel
20

St 52,3

Aluminium-Strongbacking:
Standard types
For welding steel constructions.
Extruded aluminium profile in a sea
120
water-resistant alloy, cut to length.
55 mm
Bridge grooved to customer
173,5
65
specifications.
280

Dim: (Profile) 280 x 40 mm.

We also supply in other widths,
120
e.g. 560, 770 and 840 mm.
55 mm Can be supplied grooved (single or
417
65 multiple) according to customer
560 specifications.

Advantages:
120 Quick, recyclable, cost reducing.
55 mm

65
453,5
840

51
Aluminium - Special Profiles

Alumeco takes part - from the very first Logic and logistics
idea to the finished product in an extended co-operation
In the development phase you will find that The co-operation with Alumeco does not necessar­
Alumeco is an active, creative and highly qualified ily have to end as soon as the product has been de­
sparring partner during the whole process from veloped. We are also an efficient sparring partner
the very first idea to the finished product solution. within the fields of:
It is about speaking the same language as you and
reading your demands in the particular situation. • Stock keeping

Only few competitors match the competence and • Logistics

know-how that Alumeco has accumulated con­ • Purchasing
cerning development of customer designed profiles • Assembling
in aluminium. We know the many applications of
this material. We know our customer´s demands • Packing
and have a technical knowledge enabling us to • Delivery
carry on a dialogue on a very high level. That very
dialogue with our customers is the prerequisite
for developing individual solutions and customer
designed profiles.

Outsourcing
Many companies consider what functions they with For these customers, Alumeco takes care of all busi­
advantage can entrust to external partners. This is ness from ordering to production and transporta­
also true for the total handling of aluminium. More tion. The result is a more efficient business where
and more of Alumeco´s customers choose to out­ everyone is focusing on what they do best. For
source the entire flow of aluminium to us. Alumeco it is aluminium.

52
 on our
e e m o r e examples
S
homepage

Hanging profile

Hat profile Profiles for door and window

Profiles at your free disposal

Alumeco has a certain number of dies at its disposal which can be used by all our
customers. The die costs are already paid, and no extra costs are added.

You can find more profile drawings on our site:

www.alumeco.com

53
Colour Marks According to Alloy

To avoid mixing materials we have marked our profiles and bars:

Alloy Alloy
Colour
(EN AW) DIN

2007 Al Cu Mg Pb Black (RAL 9004)

2011 Al Cu Bi Pb Red (RAL 3020)

2014 Gold (RAL 1036)

6026 Orange (RAL 2004)

5083 AlMg4,5Mn0,7 Brown (RAL 8002)

5754 Al Mg 3 Yellow (RAL 1023)

6005 Al Mg Si 0.7 Turquoise (RAL 5018)

6012 Al Mg Si Pb White (RAL 9010)

6012A Pink (RAL 4003)

6060 Al Mg Si 0.5 Colourless

6073 Al Mg Si 1 Green (RAL 6018)

6082 Al Mg Si 1 Blue (RAL 5010)

7075 Al Zn Mg Cu 1.5 Purple (RAL 4005)

54
Machining

Own service centre

As a natural supplement to our full service as the Band saws
leading aluminium wholesaler, Alumeco offers machi­ In addition Alumeco disposes of saws for cutting of bars
ning and sawing owing to our modern and big assem­ and profiles up to Ø 580 mm.
bly of machinery.

In our service centre we offer sawing of aluminium

Contact Alumeco A/S the next time you inquire cutting
plates in dimensions up to:
of plates and roundels, shortening of profiles, band
• width: 4300 mm sawing or foil application. We have the capacity to
• length: 7000 mm handle orders for both large and small numbers.
• thickness: 250 mm

Circular saws
For cutting of profiles and bars, Alumeco disposes of
saws with cutting dimensions up to:

• width: 600 mm
• length: 250 mm
55
Technical Information

Aluminium Sheets/Plates EN 485-2: 2008 (extraction)

Mechanical Properties
Alloy Temper Thickness Tensile strength Proof stress Elongation Bending radius* Brinell­
mm Rm Rp0.2 min. % hardness
MPa MPa HBS*
above to Min. Max. Min. Max. A50 mm A 180˚ 90˚
EN AW-1200 O/H111 0.5 1.5 75 105 25 21 0t 0t
Al99.0 1.5 3.0 75 105 25 24 0t 0t 23
H12 0.5 1.5 95 135 75 4 0.5t 0t 31
1.5 3.0 95 135 75 5 0.5t 0.5t 31
3.0 6.0 95 135 75 6 1.0t 1.0t 31
H14 0.5 1.5 115 155 95 3 1.0t 0.5t 37
1.5 3.0 115 155 95 4 1.0t 1.0t 37
3.0 6.0 115 155 95 5 1.5t 1.5t 37
H22 0.5 1.5 95 135 65 5 0.5t 0t 30
1.5 3.0 95 135 65 6 0.5t 0.5t 30
3.0 6.0 95 135 65 10 1.0t 1.0t 30
H24 0.5 1.5 115 155 90 4 1.0t 0.5t 37
1.5 3.0 115 155 90 5 1.0t 1.0t 37
3.0 6.0 115 155 90 7 1.5t 37
EN AW-1050A O/H111 0.5 1.5 65 95 20 22 0t 0t 20
Al99.5 1.5 3.0 65 95 20 26 0t 0t 20
3.0 6.0 65 95 20 29 0.5t 0.5t 20
6.0 12.5 65 95 20 35 1.0t 1.0t 20
H112 >
_6.0 12.5 75 30 20 23
H12 0.5 1.5 85 125 65 4 0.5t 0t 28
1.5 3.0 85 125 65 5 0.5t 0.5t 28
3.0 6.0 85 125 65 7 1.0t 1.0t 28
6.0 12.5 85 125 65 9 2.0t 28
H14 0.5 1.5 105 145 85 3 1.0t 0.5t 34
1.5 3.0 105 145 85 4 1.0t 1.0t 34
3.0 6.0 105 145 85 5 1.5t 34
6.0 12.5 105 145 85 6 2.5t 34
H22 0.5 1.5 85 125 55 5 0.5t 0t 27
1.5 3.0 85 125 55 6 0.5t 0.5t 27
3.0 6.0 85 125 55 11 1.0t 1.0t 38
H24 0.5 1.5 105 145 75 4 1.0t 0.5t 33
1.5 3.0 105 145 75 5 1.0t 1.0t 33
3.0 6.0 105 145 75 8 1.5t 1.5t 33
6.0 12.5 105 145 75 8 2.5t 33
EN AW-3103 O/H111 0.5 1.5 90 130 35 19 0t 0t 27
AlMn 1 1.5 3.0 90 130 35 21 0t 0t 27
3.0 6.0 90 130 35 24 1.0t 1.0t 27
H12 0.5 1.5 115 155 85 4 1.5t 0.5t 36
1.5 3.0 115 155 85 5 1.5t 1.0t 36
3.0 6.0 15 155 85 6 1.0t 36
H14 0.5 1.5 140 180 120 2 2.0t 1.0t 45
1.5 3.0 140 180 120 3 2.0t 1.0t 45
3.0 6.0 140 180 120 4 2.0t 45
H22 0.5 1.5 115 155 75 7 1.0t 0.5t 36
1.5 3.0 115 155 75 8 1.0t 1.0t 36
3.0 6.0 115 155 75 9 1.0t 36
H24 0.5 1.5 140 180 110 4 1.5t 1.0t 44
1.5 3.0 140 180 110 5 1.5t 1.0t 44
3.0 6.0 140 180 110 6 2.0t 44
EN AW-3105 O/H111 0.5 1.5 100 155 40 15 0t 29
Al Mn1Mg 0.5 1.5 3.0 100 155 40 17 0.5t 29
H12 0.5 1.5 130 180 105 4 1.5t 41
1.5 3.0 130 180 105 4 1.5t 41
H14 0.5 1.5 150 200 130 2 2.5t 48
1.5 3.0 150 200 130 2 2.5t 48
H22 0.5 1.5 130 180 105 6 41
1.5 3.0 130 180 105 7 41
H24 0.5 1.5 150 200 120 4 2.5t 47
1.5 3.0 150 200 120 5 2.5t 47
EN AW-5005 O/H111 0.5 1.5 100 145 35 19 0t 0t 29
AlMg1 1.5 3.0 100 145 35 20 0.5t 0t 29
3.0 6.0 100 145 35 22 1.0t 1.0t 29
H12 0.5 1.5 125 165 95 2 1.0t 0.5t 39
1.5 3.0 125 165 95 4 1.5t 1.0t 39
3.0 6.0 125 165 95 5 1.0t 39
H14 0.5 1.5 145 185 120 2 2.0t 1.0t 48
1.5 3.0 145 185 120 3 2.0t 1.0t 48
3.0 6.0 145 185 120 4 2.0t 48
H22/H32 0.5 1.5 125 165 80 5 1.0t 0.5t 38
1.5 3.0 125 165 80 6 1.5t 1.0t 38
3.0 6.0 125 165 80 8 1.0t 38
H24/H34 0.5 1.5 145 185 110 4 1.5t 1.0t 47
1.5 3.0 145 185 110 5 2.0t 1.0t 47
3.0 6.0 145 185 110 6 2.0t 47
EN AW-5052 O/H111 0.5 1.5 170 215 65 14 0t 0t 47
AlMg 2.5 1.5 3.0 170 215 65 16 0.5t 0.5t 47
3.0 6.0 170 215 65 18 1.0t 47
6.0 12.5 165 215 65 19 2.0t 46
* They also contain values of bend radius and hardness following sampling and test methods as More information on page 57
described in EN 485-1. These values are for information only.

56
Aluminium Sheets/Plates EN 485-2: 2008 (extraction)
Mechanical Properties
Alloy Temper Thickness Tensile strength Proof stress Elongation Bending radius* Brinell­
mm Rm Rp0.2 min. % hardness
MPa MPa HBS*
above to Min. Max. Min. Max. A50 mm A 180˚ 90˚
EN AW-5052 12.5 80 165 215 65 18 46
AlMg2.5 H112 >
_6.0 12.5 190 110 7 55
12.5 40.0 170 70 10 47
40.0 80.0 170 70 14 47
H12 0.2 0.5 210 260 160 4 63
0.5 1.5 210 260 160 5 63
1.5 3.0 210 260 160 6 63
1.5 3.0 210 260 160 6 63
3.0 6.0 210 260 160 8 63
6.0 12.5 210 260 160 10 63
H14 0.5 1.5 230 280 180 3 69
1.5 3.0 230 280 180 4 69
3.0 6.0 230 280 180 4 69
6.0 12.5 230 280 180 5 69
H22/H32 0.5 1.5 210 260 130 6 1.5t 1.0t 61
1.5 3.0 210 260 130 7 1.5t 1.5t 61
3.0 6.0 210 260 130 10 1.5t 61
6.0 12.5 210 260 130 12 2.5t 61
H24/H34 0.5 1.5 230 280 150 5 2.0t 1.5t 67
1.5 3.0 230 280 150 6 2.0t 2.0t 67
3.0 6.0 230 280 150 7 2.5t 67
6.0 12.5 230 280 150 9 3.0t 67
EN AW-5754 O/H111 0.5 1.5 190 240 80 14 0.5t 0.5t 52
AlMg3 1.5 3.0 190 240 80 16 1.0t 1.0t 52
3.0 6.0 190 240 80 18 1.0t 1.0t 52
6.0 12.5 190 240 80 18 2.0t 52
12.5 100.0 190 240 80 17 52
H112 >
_6.0 12.5 210 140 12 62
12.5 25.0 200 120 10 58
25.0 40.0 190 80 12 52
40.0 80.0 190 80 14 52
H12 0.5 1.5 220 270 170 5 66
1.5 3.0 220 270 170 6 66
3.0 6.0 220 270 170 7 66
6.0 12.5 220 270 170 9 66
H14 0.5 1.5 240 280 190 3 72
1.5 3.0 240 280 190 4 72
3.0 6.0 240 280 190 4 72
6.0 12.5 240 280 190 5 72
H22/H32 0.5 1.5 220 270 130 8 1.5t 1.0t 63
1.5 3.0 220 270 130 10 2.0t 1.5t 63
3.0 6.0 220 270 130 11 1.5t 63
6.0 12.5 220 270 130 10 2.5t 63
H24/H34 0.5 1.5 240 280 160 6 2.5t 1.5t 70
1.5 3.0 240 280 160 7 2.5t 2.0t 70
3.0 6.0 240 280 160 8 2.5t 70
6.0 12.5 240 280 160 10 3.0t 70
EN AW-5083 O/H111 0.5 1.5 275 350 125 12 1.0t 1.0t 75
AlMg4.5Mn0.7 1.5 3.0 275 350 125 13 1.5t 1.0t 75
3.0 6.0 275 350 125 15 1.5t 75
6.0 12.5 275 350 125 16 2.5t 75
12.5 50.0 275 350 125 15 75
50.0 80.0 270 345 115 14 73
80.0 120.0 260 110 12 70
120.0 150.0 255 105 12 69
H112 >
_6.0 12.5 275 125 12 75
12.5 40.0 275 125 10 75
40.0 80.0 270 115 10 73
H116 >
_1.5 3.0 305 215 8 3.0t 2.0t 89
3.0 6.0 305 215 10 2.5t 89
6.0 12.5 305 215 12 4.0t 89
12.5 40.0 305 215 10 89
40.0 80.0 285 200 10 83
H12 0.5 1.5 315 375 250 4 94
3.0 6.0 315 375 250 6 94
6.0 12.5 315 375 250 7 94
H14 0.5 1.5 340 400 280 3 1020
1.5 3.0 340 400 280 3 1020
3.0 6.0 340 400 280 3 1020
6.0 12.5 340 400 280 1020
H22/H32 0.5 1.5 305 380 215 6 2.0t 1.5t 89
1.5 3.0 305 380 215 7 3.0t 2.0t 89
3.0 6.0 305 380 215 8 2.5t 89
6.0 12.5 305 380 215 10 3.5t 89
H24/H34 0.5 1.5 340 400 250 5 2.0t 99
1.5 3.0 340 400 250 6 2.5t 99
3.0 6.0 340 400 250 7 3.5t 99
6.0 12.5 340 400 250 8 4.5t 99
* They also contain values of bend radius and hardness following sampling and test methods as More information on page 58
described in EN 485-1. These values are for information only.

57
Technical Information

Aluminium Sheets/Plates EN 485-2: 2008 (extraction)

Mechanical Properties
Alloy Temper Thickness Tensile strength Proof stress Elongation Bending radius* Brinell­
mm Rm Rp0.2 min. % hardness*
MPa MPa HBS
above to Min. Max. Min. Max. A50 mm A 180˚ 90˚
EN AW-6082 O >
_0.4 1.5 150 85 14 1.0t 0.5t 40
AlSiMgMn 1.5 3.0 150 85 16 1.0t 1.0t 40
3.0 6.0 150 85 18 1.5t 40
6.0 12.5 150 85 17 2.5t 40
12.5 25.0 155 16 40
T4/T451 >
_0.4 1.5 205 110 12 3.0t 1.5t 58
1.5 3.0 205 110 14 3.0t 2.0t 58
3.0 6.0 205 110 15 3.0t 58
6.0 12.5 205 110 14 4.0t 58
T451 12.5 40.0 205 110 13 58
40.0 80.0 205 110 12 58
T42 >
_0.4 1.5 205 95 12 1.5t 57
1.5 3.0 205 95 14 2.0t 57
3.0 6.0 205 95 15 3.0t 57
6.0 12.5 205 95 14 4.0t 57
12.5 40.0 205 95 13 57
40.0 80.0 205 95 12 57
T6/T651/T62 >
_0.4 1.5 310 260 6 2.5t 94
1.5 3.0 310 260 7 3.5t 94
3.0 6.0 310 260 10 4.5t 94
6.0 12.5 300 255 9 6.0t 91
T651/T62 12.5 60.0 295 240 8 89
60.0 100.0 295 240 7 89
100.0 150.0 275 240 6 84
150.0 175.0 275 230 4 83
T61/T6151 >
_0.4 1.5 280 205 10 2.0t 82
1.5 3.0 280 205 11 2.5t 82
3.0 6.0 280 205 11 4.0t 82
6.0 12.5 280 205 12 5.0t 82
T6151 12.5 60.0 275 200 12 81
60.0 100.0 275 200 10 81
100.0 150.0 275 200 9 81
150.0 175.0 275 200 8 81
EN AW-7020 O >
_0.4 1.5 220 140 12 45
AlZn4.5Mg1 1.5 3.0 220 140 13 45
3.0 6.0 220 140 15 45
6.0 12.5 220 140 12 45
T4/T451 >
_0.4 1.5 320 210 11 2.0t 92
1.5 3.0 320 210 12 2.5t 92
3.0 6.0 320 210 13 3.5t 92
6.0 12.5 320 210 14 5.0t 92
T6/T651/T62 >
_0.4 1.5 350 280 7 3.5t 104
1.5 3.0 350 280 8 4.0t 104
3.0 6.0 350 280 10 5.5t 104
6.0 12.5 350 280 10 8.0t 104
T651 12.5 40.0 350 280 9 104
40.0 100.0 340 270 8 101
100.0 150.0 330 260 7 98
150.0 175.0 330 260 6 98
EN AW-7075 O 1.5 3.0 275 145 10 3.0t 1.0t 55
AlZn5.5MgCu 3.0 6.0 275 145 10 2.5t 55
6.0 12.5 275 145 10 4.0t 55
12.5 75.0 275 9 55
T62 1.5 3.0 540 470 7 6.5t 161
3.0 6.0 545 475 8 8.0t 163
6.0 12.5 540 460 8 12t 160
T651/T62 12.5 25.0 540 470 6 161
25.0 50.0 530 460 5 158
50.0 60.0 525 440 4 155
60.0 80.0 495 420 4 147
80.0 90.0 490 390 4 144
90.0 100.0 460 360 3 135
100.0 120.0 410 300 2 119
120.0 150.0 360 260 2 104
T76/T7651 >
_1.5 3.0 500 425 7 149
3.0 6.0 500 425 8 149
6.0 12.5 490 415 7 146

* They also contain values of bend radius and hardness following sampling and test methods as described in EN 485-1. These values are for
information only.

58
Aluminium Bars - Extruded EN 755-2: 2008 (extraction)
Mechanical Properties
Alloy Temper Extruded Round bar- Dimensions Extruded Tensile 0.2% Elongation
profiles diameter square round bars strength Proof stress
hexagonal
bars Rm Rp 0.2

e (3) (10) D (1) S (2) e (3) N/mm2 N/mm2 A50 mm A

mm mm mm mm
% %
above to above to above to above to Min. Max. Min. Max. min. min.
EN AW-1050A F, H112 (4) all all all 60 - 20 - 25 23
Al99,5 O, H111 all all all 60 95 20 - 25 23
EN AW-2007 T4, T4510, T4511 (5) 0 80 0 80 0 25 370 - 250 - 8 6
AlCu4PbMgMn T4, T4510, T451 (5) 80 200 80 200 340 - 220 - 8 -
T4, T4510, T451 (5) 200 250 200 250 330 - 210 - 7 -
EN AW-2011 T4 (5) 0 200 0 60 275 - 125 - 14 12
AlCu6BiPb T6 (5) 0 75 0 60 310 - 230 - 8 6
T6 (5) 75 200 - - 295 - 195 - 6 -
T6 (5) 0 25 310 - 230 - 6 4
EN AW-2014 O, H111 0 200 0 200 - 250 - 135 12 10
AlCu4SiMn T4, T4510, T4511 0 25 0 25 370 - 230 - 13 11
T4, T4510, T4511 25 75 25 75 410 - 270 - 12 -
T4, T4510, T4511 75 150 75 150 390 - 250 - 10 -
T4, T4510, T4511 150 200 150 200 350 - 230 - 8 -
T6, T4510, T6511 0 25 0 25 415 - 370 - 6 5
T6, T4510, T6511 25 75 25 75 460 - 415 - 7 -
T6, T4510, T6511 75 100 75 150 465 - 420 - 7 -
T6, T4510, T6511 150 200 150 200 430 - 350 - 6 -
T6, T4510, T6511 200 250 200 250 420 - 320 - 5 -
O, H111 0 20 - 250 - 135 12 10
T4, T4510, T4511 0 20 370 - 230 - 11 10
T6, T4510, T6511 0 10 415 - 370 - 7 5
T6, T4510, T6511 10 40 450 - 400 - 6

En AW-2017A O, H111 0 200 0 200 - 250 - 135 12 10

AlCu4MgSi(A) T4, T4510, T4511 (5) 0 25 0 25 380 - 260 - 12 10
T4, T4510, T4511 (5) 25 75 25 75 400 - 270 - 10 -
T4, T4510, T4511 (5) 75 150 75 150 390 - 260 - 9 -
T4, T4510, T4511 (5) 150 200 150 200 370 - 240 - 8 -
T4, T4510, T4511 (5) 200 250 200 250 360 - 220 - 7 -
O, H111 0 20 - 250 - 135 12 10
T4, T4510, T4511 (5) 0 10 380 - 260 - 12 10
T4, T4510, T4511 (5) 10 75 400 - 270 - 10 8
En AW-2024 O, H111 0 200 0 200 - 250 - 150 12 10
AlCu4Mg1 T3, T3510, T3511 0 50 0 50 450 - 310 - 8 6
T3, T3510, T3511 50 100 50 100 440 - 300 - 8 -
T3, T3510, T3511 100 200 100 200 420 - 280 - 8 -
T3, T3510, T3511 200 250 200 250 400 - 270 - 8 -
T8, T8510, T8511 0 150 0 150 455 - 380 - 5 4
O, H111 0 30 - 250 - 150 12 10
T3, T3510, T3511 0 30 420 - 290 - 8 6
T8, T8510, T8511 0 30 455 - 380 - 5 4
EN AW-5754 F, H112 (4) 0 150 0 150 0 25 180 - 80 - 14 12
AlMg3 F, H112 (4) 150 250 150 250 180 - 70 - 13 -
O, H111 0 150 0 150 0 25 180 250 80 - 17 15
EN AW-5083 F, (4) 0 200 0 200 all 270 - 110 - 12 10
AlMg4.5Mn0.7 F, (4) 200 250 200 250 260 - 110 - 12 -
O, H111 0 200 0 200 all 270 - 110 - 14 12
O, H112 0 200 0 200 all 270 - 125 - 12 10
F, (4) all 270 - 110 - 12 10
O, H111 all 270 - 110 - 14 12

O, H112 all 270 - 125 - 12 10

EN AW-6005 T4 (5)(Å) 0 25 180 - 90 - 15 13
AlSiMg T6 (5) 25 50 25 50 270 - 225 - 8 -
T6 (5)(Å) 0 5 270 - 225 - 8 6
T6 (5)(Å) 5 10 260 - 215 - 8 6
T6 (5)(Å) 10 25 250 - 200 - 8 6
T4 (5)(H) 0 10 180 - 90 - 15 13
T6 (5)(H) 0 5 255 - 215 - 8 6
T6 (5)(H) 5 15 250 - 200 - 8 6
T6 (5) 0 25 0 25 270 - 225 - 10 8
T6 (5) 50 100 50 100 260 - 215 - 8 -
T6 (5) 0 5 270 - 225 - 8 6
T6 (5) 5 10 260 - 215 - 8 6

(1) D = Diameter for round bars. Å = Open profile

(2) S = Cross section for square and hexagonal bars, plus thickness for flat profiles and bars. H = Hollow profile
(3) e = Wall thickness.
(4) F-Condition: The mechanical properties are only intended as a guide.
(5) The properties can only be reached by shock cooling.
10) When a profile’s cross section consists of different wall thicknesses with different mechanical properties,
the lowest specified value must be considered as the effective value for the whole profile.
More information on page 60

59
Technical Information

Aluminium Bars - Extruded EN 755-2: 2008 (extraction)

Mechanical Properties
Alloy Temper Extruded Round bar- Dimensions Extruded Tensile 0.2% Elongation
profiles diameter square round bars strength Proof stress
hexagonal
bars Rm Rp 0.2

e (3) (10) D (1) S (2) e (3) N/mm2 N/mm2 A50 mm A

mm mm mm mm
% %
above to above to above to above to Min. Max. Min. Max. min. min.
EN AW-6012 T6, T6510, T6511 (5) 0 150 0 150 0 30 310 - 260 - 8 6
Al MgSiPb T6, T6510, T6511 (5) 150 200 150 200 260 - 200 - 8 -
EN AW-6060 T4 (5) 0 25 0 150 0 150 0 15 120 - 60 - 16 14
Al MgSi 0.5 T5 0 5 0 150 0 150 0 15 160 - 120 - 8 6
T5 5 25 140 - 100 - 8 6

T6 (5) 0 3 0 150 0 150 0 15 190 - 150 - 8 6

T6 (5) 3 25 170 - 140 - 8 6
T64 (5) (8) 0 15 0 50 0 50 0 15 180 - 120 - 12 10
T66 (5) 0 3 0 150 0 150 0 15 215 - 160 - 8 6
T66 (5) 3 25 195 - 150 - 8 6
EN AW-6061 O, H111 0 200 0 200 - 150 - 110 16 14
Al Mg1SiCu T4 (5) 0 200 0 200 180 - 110 - 15 13
T6 (5) 0 200 0 200 260 - 240 - 8 6
O, H111 0 25 - 150 - 110 16 14
T4 (5) 0 25 180 - 110 - 15 13
T6 (5) 0 5 260 - 240 - 8 6
T6 (5) 5 25 260 - 240 - 10 8
EN AW-6082 O, H111 all 0 200 0 200 0 25 - 160 - 110 14 12
AlSi1MgMn T4 (5) 0 25 205 - 110 - 14 12
T5 (Å+H) 0 5 270 - 230 - 8 6
T6 (5)(Å+H) 0 5 290 - 250 - 8 6
T6 (5)(Å) 5 25 310 - 260 - 10 8
T6 (5)(H) 5 15 310 - 260 - 10 8
T4 (5) 0 200 0 200 0 25 205 - 110 - 14 12
T6 (5) 0 20 0 20 0 5 295 - 250 - 8 6
T6 (5) 20 150 20 150 310 - 260 - 8 -
T6 (5) 150 200 150 200 280 - 240 - 6 -
T6 (5) 200 250 200 250 270 - 200 - 6 -
T6 (5) 5 25 310 - 260 - 10 8
EN AW-6262
AlMg1SiPb T6 (5) 0 25 0 200 0 200 0 25 260 - 240 - 10 8
EN AW-6262R
AlMg1SiPb T6 (5) 0 25 0 200 0 200 0 25 260 - 240 - 10 8
En AW-7020 T6 (5) 0 50 0 50 350 - 290 - 10 8
AlZn4.5Mg1 T6 (5) 50 200 50 200 340 - 275 - 10 -
T6 (5) 0 15 350 - 290 - 10 8
EN AW-7022 T6, T6510, T6511 (5) 0 80 0 80 0 30 490 - 420 - 7 5
Al Zn5Mg3Cu T6, T6510, T6511 (5) 80 200 80 200 470 275 400 165 7 -
EN AW-7075 O, H111 0 200 0 200 - - - 10 8
Al Zn 5.5MgCu T6, T6510, T6511 0 25 0 25 540 - 480 - 7 5
T6, T6510, T6511 25 100 25 100 560 - 500 - 7 -
T6, T6510, T6511 100 150 100 150 530 - 470 - 6 -

T6, T6510, T6511 150 200 150 200 470 - 400 - 5 -

T73, T73510, T7351 (9) 0 25 0 25 485 - 420 - 7 5

T73, T73510, T7351 (9) 25 75 25 75 475 - 405 - 7 -

T73, T73510, T7351 (9) 75 100 75 100 470 - 390 - 6 -
T73, T73510, T7351 (9) 100 150 100 150 440 - 360 - 6 -
O, H111 0 10 - 275 - 165 10 -
T6, T6510, T6511 0 5 540 - 485 - 8 6
T6, T6510, T6511 5 10 560 - 505 - 7 5
T6, T6510, T6511 10 50 560 - 495 - 6 4
T73, T73510, T7351 (9) 0 5 470 - 400 - 7 5

T73, T73510, T7351 (9) 5 25 485 - 420 - 8 6

(1) D = Diameter for round bars. Å = Open profile

(2) S = Cross section for square and hexagonal bars, plus thickness for flat profiles and bars. H = Hollow profile
(3) e = Wall thickness.
(5) The properties can only be reached by shock cooling.
(8) Bending quality.
(9) Referring to supplement A and supplement B for material in this condition.
(10)When a profile’s cross section consists of different wall thicknesses with different mechanical properties,
the lowest specified value must be considered as the effective value for the whole profile.

60
Aluminium Bars - Drawn EN 754-2: 2008 (extraction)
Mechanical Properties
Alloy Temper Material Round bar- Dimensions Drawn Tensile 0.2% Elongation
no. diameter square tube strength Proof stress
hexagonal
bars Rm Rp 0.2

D (1) S (2) e (3) N/mm2 N/mm2 A50 mm A

mm mm mm
% %
above to above to above to Min. Max. Min. Max. min. min.
EN AW-2007 T3 (4) 3.1645.53 0 30 0 30 370 - 250 - 7 5
AlCu4PbMgMn T3 (4) 3.1645.53 30 80 30 80 340 - 220 - 6 -
T351 (4) 3.1645.53 0 80 0 80 370 - 250 - 5 3
T3 (4) 3.1645.53 0 20 370 - 250 - 7 5
T3510, T3511 (4) 3.1645.53 0 20 370 - 250 - 5 3
EN AW-2011 T3 3.1645.53 0 40 0 40 320 - 270 - 10 8
AlCu6BiPb T3 3.1645.53 40 50 40 50 300 - 250 - 10 -
T3 3.1645.53 50 80 50 80 280 - 210 - 10 -
T8 0 80 0 80 370 - 270 - 8 6
T3 3.1645.53 0 5 310 - 260 - 10 8
T3 3.1645.53 5 20 290 - 240 - 8 6
T8 0 20 370 - 275 - 8 6
EN AW-6012 T4 (4) 3.0615.51 0 80 0 80 0 20 200 - 100 - 10 8
AlMgSiPb T6 (4) 3.0615.71 0 80 0 80 0 20 310 - 260 - 8 6
EN AW-6061 O, H111 3.3211.10 0 80 0 80 0 20 - 150 - 110 16 14

AlMg1SiCU T4 (4) 3.3211.51 0 80 0 80 0 20 205 110 - 16 14

T6 (4) 3.3211.71 0 80 0 80 0 20 290 - 240 - 10 8
EN AW-6262R T6 (4) 0 80 0 80 0 20 290 - 240 - 10 8
AlMg1SiPb T8 (4) 0 50 0 50 0 10 345 - 315 - 4 3
T9 (4) 0 50 0 50 0 10 360 - 330 - 4 3
EN AW-6262 T6 (4) 0 80 0 80 0 20 290 - 240 - 10 8
AlMg1SiPb T8 (4) 0 50 0 50 0 10 345 - 315 - 4 3
T9 (4) 0 50 0 50 0 10 360 - 330 - 4 3
EN AW-6082 O, H111 3.2315.10 0 80 0 80 0 20 - 110 - 110 15 13
AlSiMgMn T4 (4) 3.2315.51 0 80 0 80 0 20 205 - 110 - 14 12
T6 (4) 3.2315.71 0 80 0 80 310 - 255 - 10 9
T6 (4) 3.2315.71 0 5 310 - 255 - 8 7
T6 (4) 3.2315.71 5 20 310 - 240 - 10 9
(1) D = Diameter for round bars.
(2) S = Cross section for square and hexagonal bars, plus thickness for flat profiles and bars.
(3) e = Wall thickness.
(5) The properties can only be reached by shock cooling.
(4) P
 roperties may be obtained by press quenching.

Tolerances for Extruded Flat Profiles EN 755-5: 2008

Alloy group I: EN AW-1050A – EN AW-1350 – EN AW-6005 – EN AW-6012 – EN AW-6026 – EN AW-6082 – EN AW-6262 – EN AW-6262R

Width Tolerance Thickness Alloy group I

mm mm 2<t<6 6<t<10 10<t<18 18<t<30 30<t<50 50<t<80 80<t<120 120<t<180 180<t<240
from 10 to 18 ±0.25 ±0.20 ±0.25 ±0.25 - - - - - -
above 18 to 30 ±0.30 ±0.20 ±0.25 ±0.30 ±0.30 - - - - -
above 30 to 50 ±0.40 ±0.25 ±0.25 ±0.30 ±0.35 ±0.40 - - - -
above 50 to 80 ±0.60 ±0.25 ±0.30 ±0.35 ±0.40 ±0.50 ±0.60 - - -
above 80 to 120 ±0.80 ±0.30 ±0.35 ±0.40 ±0.45 ±0.60 ±0.70 ±0.80 - -
above 120 to 180 ±1.0 ±0.40 ±0.45 ±0.50 ±0.55 ±0.60 ±0.70 ±0.90 ±1.0 -
above 180 to 240 ±1.4 - ±0.55 ±0.60 ±0.65 ±0.70 ±0.80 ±1.0 ±1.1 ±1.4
above 240 to 350 ±1.8 - ±0.65 ±0.70 ±0.75 ±0.80 ±0.90 ±1.1 ±1.3 ±1.5
above 350 to 450 ±2.2 - - ±0.80 ±0.85 ±0.90 ±1.0 ±1.2 ±1.4 ±1.6
above 450 to 600 ±3.0 - - - - ±0.90 ±1.0 ±1.4 - -

Tolerances for Extruded Flat Profiles EN 755-5: 2008

Alloy group II: EN AW-2007/ EN AW-2011/ EN AW-7075

Width Tolerance Thickness Alloy group II

mm mm 2<t<6 6<t<10 10<t<18 18<t<30 30<t<50 50<t<80 80<t<120 120<t<180 180<t<240
from 10 to 18 ±0.35 ±0.25 ±0.30 ±0.35 - - - - - -
above 18 to 30 ±0.40 ±0.25 ±0.30 ±0.40 ±0.40 - - - - -
above 30 to 50 ±0.50 ±0.30 ±0.30 ±0.40 ±0.50 ±0.50 - - - -
above 50 to 80 ±0.70 ±0.30 ±0.35 ±0.45 ±0.60 ±0.70 ±0.70 - - -
above 80 to 120 ±1.0 ±0.35 ±0.40 ±0.50 ±0.60 ±0.70 ±0.80 ±1.0 - -
above 120 to 180 ±1.4 ±0.45 ±0.50 ±0.55 ±0.70 ±0.80 ±1.0 ±1.1 ±1.4 -
above 180 to 240 ±1.8 - ±0.60 ±0.65 ±0.70 ±0.90 ±1.1 ±1.3 ±1.6 ±1.8
above 240 to 350 ±2.2 - ±0.70 ±0.75 ±0.80 ±0.90 ±1.2 ±1.4 ±1.7 ±1.9
above 350 to 450 ±2.8 - - ±0.90 ±1.0 ±1.1 ±1.4 ±1.8 ±2.1 ±2.3
above 450 to 600 ±3.5 - - - - ±1.2 ±1.4 ±1.8 - -

61
Technical Information

Tolerances for Drawn Square, Hexagonale and Round Bars according to

EN 754-4: 2008
Alloy: EN AW-2007 / EN AW-2011 / EN AW-2014 / EN AW-6012 / EN AW-6026 / EN AW-6060/6063 / EN AW-6082 /
EN AW-6262 / EN AW-6262R / EN AW-7075

Dimension area Square Bars Hexagonal Bars Round Bars

Limit measurement Limit measurement Limit measurement
(permitted deviations) (permitted deviations) (permitted deviations)
from 3 to 6 0 to -0.08 0 to -0.08 0 to -0.08
above 10 to 10 0 to -0.09 0 to -0.09 0 to -0.09
above 10 to 18 0 to -0.11 0 to -0.11 0 to -0.11
above 18 to 30 0 to -0.13 0 to -0.13 0 to -0.13
above 30 to 50 0 to -0.16 0 to -0.16 0 to -0.16
above 50 to 65 0 to -0.19 0 to -0.19 0 to -0.19

Tolerances for Extruded Square, Hexagonale and Round Bars according

to EN 754-4: 2008
Alloy group: I = EN AW-6060/6063 / EN AW-6082 / EN AW-6012 / EN AW-6026 / EN AW-6262 / EN AW-6262R
II = EN AW-2007/ EN AW- 2011/ EN AW-2014/ EN AW-7075

Dimension area Square Bars Hexagonal Bars Round Bars

Alloy group Alloy group Alloy group

I II I II I II
from 8 to 18 ±0.22 ±0.30
from 10 to 18 ±0.22 ±0.30 ±0.22 ±0.30
above 18 to 25 ±0.25 ±0.35 ±0.25 ±0.35 ±0.25 ±0.35
above 25 to 40 ±0.30 ±0.40 ±0.30 ±0.40 ±0.30 ±0.40
above 40 to 50 ±0.35 ±0.45 ±0.35 ±0.45 ±0.35 ±0.45
above 50 to 65 ±0.40 ±0.50 ±0.40 ±0.50 ±0.40 ±0.50
above 65 to 80 ±0.45 ±0.70 ±0.45 ±0.70 ±0.45 ±0.70
above 80 to 100 ±0.55 ±0.90 ±0.55 ±0.90 ±0.55 ±0.90
above 100 to 120 ±0.65 ±1.00 ±0.65 ±1.00 ±0.65 ±1.00
above 120 to 150 ±0.80 ±1.20 ±0.80 ±1.20 ±0.80 ±1.20
above 150 to 180 ±1.00 ±1.40 ±1.00 ±1.40 ±1.00 ±1.40
above 180 to 220 ±1.15 ±1.70 ±1.15 ±1.70 ±1.50 ±1.70
above 220 to 270 ±1.30 ±2.00
above 270 to 320 ±1.60 ±2.50

62
Width thickness tolerances for Cold-rolled Sheets/Plates
according to EN 485-4: 2008
Alloy group: I = EN AW-1050A/ EN AW-3003/ EN AW-5005
II = EN AW-5052/ EN AW-5754 / EN AW-5083/ EN AW-6082 / EN AW-7075

Thickness to 1000 above 1000 above 1250 above 1600 above 2000 above 2500 above 3000
mm mm to 1250 mm to 1600 mm to 2000 mm to 2500 mm to 3000 mm to 3500 mm
above to I II I II I II I II I II I II I II
0.2 0.4 ±0.02 ±0.03 ±0.04 ±0.05 ±0.05 ±0.06 - - - - -
0.4 0.5 ±0.03 ±0.03 ±0.04 ±0.05 ±0.05 ±0.06 ±0.06 ±0.07 ±0.10 - -
0.5 0.6 ±0.03 ±0.04 ±0.05 ±0.06 ±0.06 ±0.07 ±0.07 ±0.08 ±0.11 - -
0.6 0.8 ±0.03 ±0.04 ±0.06 ±0.07 ±0.07 ±0.08 ±0.08 ±0.09 ±0.12 - -
0.8 1 ±0.04 ±0.05 ±0.06 ±0.08 ±0.08 ±0.09 ±0.09 ±0.10 ±0.13 - -
1 1.2 ±0.04 ±0.05 ±0.07 ±0.09 ±0.09 ±0.10 ±0.10 ±0.12 ±0.14 - -
1.2 1.5 ±0.05 ±0.07 ±0.09 ±0.11 ±0.10 ±0.12 ±0.11 ±0.14 ±0.16 - -
1.5 1.8 ±0.06 ±0.08 ±0.10 ±0.12 ±0.11 ±0.13 ±0.12 ±0.15 ±0.17 - -
1.8 2 ±0.06 ±0.09 ±0.11 ±0.13 ±0.12 ±0.14 ±0.14 ±0.16 ±0.19 - -
2 2.5 ±0.07 ±0.10 ±0.12 ±0.14 ±0.13 ±0.15 ±0.15 ±0.17 ±0.20 - -
2.5 3 ±0.08 ±0.11 ±0.13 ±0.15 ±0.15 ±0.17 ±0.17 ±0.19 ±0.23 - -
3 3.5 ±0.10 ±0.12 ±0.15 ±0.17 ±0.17 ±0.19 ±0.18 ±0.20 ±0.24 - -
3.5 4 ±0.15 ±0.20 ±0.22 ±0.23 ±0.25 ±0.34 ±0.38
4 5 ±0.18 ±0.22 ±0.24 ±0.25 ±0.29 ±0.36 ±0.42
5 6 ±0.20 ±0.24 ±0.25 ±0.26 ±0.32 ±0.40 ±0.46

Width thickness tolerances for Hot-rolled Sheets/Plates

according to EN 485-3: 2008
Thickness mm to 1250 mm above 1250 mm above 1600 mm above 2000 mm above 2500 mm
above to to 1600 mm to 2000 mm to 2500 mm to 3500 mm
2.5 4 ±0.28 ±0.28 ±0.32 ±0.35 ±0.40
4 5 ±0.30 ±0.30 ±0.35 ±0.40 ±0.45
5 6 ±0.32 ±0.32 ±0.40 ±0.45 ±0.50
6 8 ±0.35 ±0.40 ±0.40 ±0.50 ±0.55
8 10 ±0.45 ±0.50 ±0.50 ±0.55 ±0.60
10 15 ±0.50 ±0.60 ±0.65 ±0.65 ±0.80
15 20 ±0.60 ±0.70 ±0.75 ±0.80 ±0.90
20 30 ±0.65 ±0.75 ±0.85 ±0.90 ±1.00
30 40 ±0.75 ±0.85 ±1.00 ±1.10 ±1.20
40 50 ±0.90 ±1.00 ±1.10 ±1.20 ±1.50
50 60 ±1.10 ±1.20 ±1.40 ±1.50 ±1.70
60 80 ±1.40 ±1.50 ±1.70 ±1.90 ±2.00
80 100 ±1.70 ±1.80 ±1.90 ±2.10 ±2.20
100 150 ±2.20 ±2.20 ±2.70 ±2.80 -
150 200 ±2.80 ±2.80 ±3.30 ±3.30 -
Valid for alloy groups I & II

63
Profile Tolerances

Tolerance relative to the generic dimension S

Generic
Diameter of the circumscribed circel D
diemension H

< ≤ D ≤ 100 100 <D≤200 200 <D≤300 300 <D≤500 500 <D≤800
- 10 ±0.25 ±0.30 ±0.35 ±0.40 ±0.50
10 25 ±0.30 ±0.40 ±0.50 ±0.60 ±0.70 H

25 50 ±0.50 ±0.60 ±0.80 ±0.90 ±1.10

50 100 ±0.70 ±0.90 ±1.10 ±1.30 ±1.50
100 150 - ±1.10 ±1.30 ±1.50 ±1.70
150 200 - ±1.30 ±1.50 ±1.80 ±2.00
200 300 - - ±1.70 ±2.10 ±2.40
300 450 - - - ±2.80 ±3.00
450 600 - - - ±3.80 ±4.20

Tolerance related to wall thickness

Related
Diameter of the circumscribed circel D
thickness S

< ≤ D ≤ 100 100 <D≤200 300 <D≤500 500 <D≤800

- 1.5 ±0.20 ±0.30 - -
1,5 3 ±0.25 ±0.40 ±0.60 ±0.80
3 6 ±0.40 ±0.60 ±0.80 ±1.00
6 10 ±0.60 ±0.80 ±1.00 ±1.20
10 15 ±0.80 ±1.00 ±1.20 ±1.50
15 20 ±1.20 ±1.50 ±1.70 ±2.00
20 30 ±1.50 ±1.80 ±2.00 ±2.50
30 40 - ±2.00 ±2.20 ±2.70
40 50 - - - -

Tolerance related to wall thickness

For right angles
Z
Width
Deviation from straight line Z
W
> ≤
- 30 0,4
30 50 0,7
W
50 80 1,0
80 120 1,4
120 180 2,0
180 240 2,6
240 300 3,1
300 400 3,5

64
 Straigthness tolerances

The tolerance on the straigthness line h must be less than or

equal to 1,5 mm/m of the lenght. Localised differences from
the straight line must not exceed 0,6 mm/m

Flatness tolerances
Width b Difference from the flatness p
Hollow extruded products Open extruded products
> ≤
Wall thickness t
≤5 >5
- 30 0.3 0.2 0.2
30 60 0.4 0.3 0.3
60 100 0.6 0.4 0.4
100 150 0.9 0.6 0.6
150 200 1.2 0.8 0.8
200 300 1.8 1.2 1.2
300 400 2.4 1.6 1.6
400 500 3.0 2.0 2.0
500 600 3.6 2.4 2.4

Twisting tolerances
Width b Tolerances on twisting t
On the total length L
> ≤ On the length 1000 mm
1000 < L ≤ 6000 L > 6000
- 30 1.2 2.5 3.0
30 50 1.5 3.0 4.0
50 100 2.0 3.5 5.0
100 200 2.5 5.0 7.0
200 300 2.5 6.0 8.0
300 450 3.0 8.0
1.5xL (in mm)
450 600 3.5 9.5

65
Technical Information / Reference Table

Aluminium Properties - EN 485-2: 2008

Alloy Min. Min. Min. Brinell­ Spec. Thermal Coefficient Weldability Annealing Fusing- Elastic- Electrical
Proof Tensile Elon­ hard- weight conduc­ of thermal point/ modulus conduc­
stress strength gation ness tivity expansion interval tivity
Rp 0.2 Rm at 20˚ ohm-
cm x K mm2
(N/mm2) (N/mm2) A5% HBS g/cm3 W/cmxK (20-100˚C) cm/106 x ˚C C˚ KN/mm2

5754 H111 80 190 12 52 2.66 1.3-1.7 23.7 excellent 330-360 610-640 70 18-23
5083 H111 125 275 12 75 2.66 1.1-1.2 23.8 excellent 330-400 580-640 71 17
6082 T651 240 295 8 89 2.70 1.5-1.9 23.4 good 350-400 585-650 70 24-32
2017A T4 245 390 12 110 2.80 1.3-1.7 22.8 bad 350-400 512-650 72 21-28
2024 T3 290 440 13 110 2.77 1.3-1.7 22.8 bad 350-400 505-640 73 18-26
2014 T651 400 460 6 133 2.80 1.6 23.0 bad 350-400 510-640 72 23-29
7020 T651 270 340 8 101 2.77 1.2-1.6 23.0 good 350-400 580-650 70 18-24
7022 T651 350 430 5 127 2.78 1.3-1.5 23.6 bad -- 515-640 71 17-19
7075 T651 440 525 4 155 2.80 1.3-1.6 23.3 bad -- 500-640 72 17-20
7050 Hokotol 532 757 7.8 180 2.83 1.54 23.5 bad -- 560-600 70.3 23
The indicated numbers are guidelines only.

Aluminium Material Abbreviation:

Germany Material ISO / USA UK France Spain Italy Sweden
DIN no. EN-norm BS NF UNE UNI SIS
Al 99.5 3.0255 1050A 1050A 1B A5 L3051 4507 4007
Al 99.7 3.0275 1070A 1070A - A7 - - 4005
Al 99.8 3.0285 1080A 1080A 1A A8 - - 4004
Al 99.0 3.0205 1200 1200 1C A4 - - 4010
E-Al 99.5 3.0257 1350A 1350A 1E A5L L3052 - 4008
AlCuMgPb 3.1645 2007 2007 - A-U4Pb L3121 - 4335
AlCuBiPb 3.1655 2011 2011 FC1 A-U 4Pb L3192 6362 4355
AlCuSiMn 3.1255 2014 2014 - - - - 4338
AlCuMg 1 3.1325 2017A 2017A H14 A-U4G L3120 3576 -
AlCuMg 2 3.1355 2024 2024 H16 A-U4G1 - - -
AlMn 3.0515 3003 3003 N3 - - - 4054
AlMg1 3.3315 5005 5005 - - - - 4106
AlMg2.5 3.3523 5052 5052 N4 - - - 4120
AlMg5 3.3555 5056 5056 N6 A-G5 - - -
AlMg 4.5 Mn 3.3547 5083 5083 N8 5083 L3321 7790 4140
AlMg3 3.3535 5754 5754 N5 A-G3M L3390 3575 4125
AlMgSi0.7 3.3210 6005 6005 - - - - 4107
AlMgSiPb 3.0615 6012 6012 - - - -
AlMgSi0.5 3.3206 6060/63 6060/63 H9 A-GS L3441 3569 4104
AlMg1SiCu 3.3211 6061 6061 H20 - - - -
AlMgSi1 3.2315 6082 6082 H30 A-SGM 0.7 L3451 3571 4212
AlZn 4.5 Mg 1 3.4335 7020 7020 H17 A-Z5G L3741 7791 4425
AlZnMgCu 0.5 3.4345 7022 7022 - A-Zn5 GU 0.6 - - -
AlZnMgCu 1.5 3.4365 7075 7075 2L95 A-Zn5 GU L3710 3735 -

66
Reference Table DIN-standard / EN-standard
Approximate comparison, as EN-standard cannot replace DIN-standard.

Type Alloy Properties Tolerances

DIN EN DIN EN DIN EN
Al99.5 K 1712 573-3 1745 485-1/2 1783 485-4
EN AW-1050A V 59600 485-3
AlMg3 K 1725 573-3 1745 485-1/2 1783 485-4
EN AW-5754 V 59600 485-3
AlMg4.5Mn K 1725 573-3 1745 485-1/2 1783 485-4
EN AW-5083 V 59600 485-3
AlMgSi1 K 1725 573-3 1745 485-1/2 1783 485-4
EN AW-6082 V 59600 485-3
AlZnMgCu1.5 K 1725 573-3 1745 485-1/2 59600 485-3
EN AW-7075
AlMg1 K 1725 573-3 1745 485-1/2 1783 485-4
EN AW-5005
Tread Plate AlMg3 1725 573-3 59605 1386 59605 1386
EN AW-5754
Round Bars Drawn 1725 573-3 1747 754-1/2 1798 754-3
Extruded 755-1/2 1799 755-3
Square Bars Drawn 1725 573-3 1747 754-1/2 1796 755-4
Extruded 755-1/2 59700 755-4
Hexagonal Bars Drawn 1725 573-3 1747 754-1/2 1797 754-6
Extruded 755-1/2 59700 755-6
Flat Profiles 1725 573-3 1747 755-1/2 1770 755-5
Angle Profiles 1725 573-3 1748 755-1/2 1771
U-Profiles 1725 573-3 1748 755-1/2 9713
T-Profiles 1725 573-3 1746 755-1/2 9714
Round Tubes 1725 573-3 1746 755-1/2 9107 755-8
Square Tubes 1725 573-3 1748 755-1/2 1748 755-8

K = Cold-rolled • V = Hot-rolled

Temper Description Comparison DIN-standard - EN-standard

DIN-standard EN-Standard Temper Temper Description Comparison DIN-standard - EN-standard
material no. 1994 Al99.5-1050A AlMg1-5005A AlMg3-5754 AlMg4.5Mn-5083 AlMgSi1-6082

xxxx-H112 Hot-rolled with prescribed

x.xxxx.07
strength value
-F Hot-rolled without prescribed
.08
strength value
-0 Soft
.10 W7 - 0 W11 - 0 W19 - 0 W28-0
non-hardable alloys
-H111 Soft, stretch-straightened
.10 W19 - H111 W28 - H111
non-hardable alloys
-0 Soft
.10 W-0
hardable alloys
-H12 Cold-rolled
.24 F9 - H12 F13 - H12 F22 - H12
to 1/4 hard
-H14 Cold-rolled
.26 F11 - H14 F15 - H14 F24 - H14
to 1/2 hard
Cold-rolled
.30 F15 - H18 F19 - H18 F29 - H18
to 1/1 hard
-H22/H32 Cold-rolled, annealed
.25 G9 - H22/H32 G13 - H22/H32 G22 - H22/H32 G31 - H22/H32
to 1/4 hard
-H24/H34 Cold-rolled, annealed
.27 G11 - H24/H34 G15 - H24/H34 G24 - H24/H34 G35 - H24/H34
to 1/2 hard
Cold-rolled, annealed
.29 -H26/H36 G17 - H26/H36 G27 - H26/H36
to 3/4 hard
Cold-rolled, annealed
.31 -H28/H38 F21 - T4/T451
to 1/1 hard

.51 -T4/T451 Cold-hardened

Cold-hardened with
.53 -T3/T351 fiber structure
.71 -T6/T651 Temper-hardened F28 - T6/T651
.72 -T6/T651 Temper-hardened F32 - T6/T651

67
Technical Information

EN 515: 2000
Temper Definition
F1)
As fabricated (no mechanical property limits specified).
O2) Annealed - products achieving the required annealed properties after hot forming processes may be designated
as O temper.
O1 Thermally treated at approximately the same time and temperature required for solution treatment and slow
cooled to room temperature (formerly designated as T41).
O2 Thermomechanically processed to enhance formability, such as required for super-plastic forming (SPF).
O3 Homogenized.
H12 Strain-hardened - 1/4 hard.
H14 Strain-hardened - 1/2 hard.
H16 Strain-hardened - 3/4 hard.
H18 Strain-hardened - 4/4 hard (fully hardened).
H19 Strain-hardened - extra hard.
Hxx4 Applies to embossed or patterned sheet or strip, fabricated from the corresponding Hxx temper.
Hxx5 Strain-hardened - applies to welded tubes.
H111 Annealed and slightly strain-hardened (less than H11) during subsequent operations such as stretching or levelling.
H112 Slightly strain-hardened from working at an elevated temperature from a limited amount of cold work
(mechanical property limits specified).
H116 Applies to aluminium-magnesium alloys with a magnesium content of 4% or more and for which mechanical
property limits and exfoliation corrosion resistance are specified.
H22 Strain-hardened and partially annealed - 1/4 hard.
H24 Strain-hardened and partially annealed - 1/2 hard.
H26 Strain-hardened and partially annealed - 3/4 hard.
H28 Strain-hardened and partially annealed - 4/4 hard (fully hardened).
H32 Strain-hardened and stabilized - 1/4 hard.
H34 Strain-hardened and stabilized - 1/2 hard.
H36 Strain-hardened and stabilized - 3/4 hard.
H38 Strain-hardened and stabilized - 4/4 hard (fully hardened).
H42 Strain-hardened and painted or lacquered - 1/4 hard.
H44 Strain-hardened and painted or lacquered - 1/2 hard.
H46 Strain-hardened and painted or lacquered - 3/4 hard.
H48 Strain-hardened and painted or lacquered - 4/4 hard (fully hardened).
W Solution heat-treated (unstable temper). The period of natural ageing (W2h..) may also be specified.
W51 Solution heat-treated (unstable temper) and stress-relieved by controlled stretching (permanent set 0.5% to 3%
for sheet, 1.5% to 3% for plate, 1% to 3% for hand or ring forging and rolled ring). The products receive no
further straightening after stretching.
W510 Solution heat-treated (unstable temper) and stress-relieved by controlled stretching (permanent set 1% to 3%
for extruted rod, bar, shapes and tube, 0.5% to 3% for drawn tube).
The products receive no further straightening after stretching.
W511 Same as W510 except minor straightening is allowed after stretching to comply with standard tolerances.
W52 Solution heat-treated (unstable temper) and stress-relieved by compressing to produce a permanent set of 1- 5%.
W54 Solution heat-treated (unstable temper) and stress-relieved by restriking cold in the finish die (die forging).
T1 Cooled from an elevated temperature shaping process and naturally aged.
T2 Cooled from an elevated temperature shaping process, cold worked and naturally aged.
T33) Solution heat-treated, cold worked and naturally aged.
T31 Solution heat-treated, cold worked approximately 1% and naturally aged.
T351 S olution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to
3% for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled
ring) and naturally aged. The products receive no further straightening after stretching.
T3510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar,
shapes and tube, 0.5% to 3% for drawn tube) and naturally aged. The products receive no further
straightening after stretching.
T3511 Same as T3510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T352 Solution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and naturally aged.

68
EN 515: 2000
Temper Definition
T354 Solution heat-treated stress-relieved by restriking cold in the finish die and naturally aged.
T36 Solution heat-treated, cold worked approximately 6% and naturally aged.
T37 Solution heat-treated, cold worked approximately 7% and naturally aged.
T39 Solution heat-treated and cold worked to an appropriate degree to achieve the specified mechanical properties.
Cold work may be carried out before or after natural ageing.
T44) Solution heat-treated and naturally aged.
T42 Solution heat-treated and naturally aged. Applies to test material heat-treated from annealed or F temper or to
products heat-treated from any temper by the user.
T451 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to 3%
for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled ring)
and naturally aged. The products receive no further straightening after stretching.
T4510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar
shapes and tube, 0.5% to 3% for drawn tube) and naturally aged. The products receive no further
straightening after stretching.
T4511 Same as T4510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T452 Solution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and naturally aged.
T454 Solution heat-treated, stress-relieved by restriking cold in the finish die and naturally aged.
T5 Cooled from an elavated temperature shaping process and then artificially aged.
T51 Cooled from an elavated temperature shaping process and then artificially aged in underageing conditions to
improve formability.
T56 Cooled from an elevated temperature shaping process and then artificially aged - mechanical property level
higher than T5 achieved through special control of the process (6000 series alloys).
T65) Solution heat-treated and then artificially aged.
T61 Solution heat-treated and then artificially aged in underageing conditions to improve formability.
T6151 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to 3%
for plate and then artificially aged in underageing conditions to improve formability. The products
receive no further straightening after stretching.
T62 Solution heat-treated and then artificially aged. Applies to test material heat-treated from annealed or F
temper or to products heat-treated from any temper by the user.
T64 Solution heat-treated and then artificially aged in underageing conditions (between T6 and T61) to improve
formability.
T651 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to
3% for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled
ring and then artificially aged. The products receive no further straightening after stretching.
T6510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded
rod, bar, shapes and tube, 0.5% to 3% for drawn tube) and then artificially aged. The products receive no
further straightening after stretching.
T6511 Same as T6510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T652 S olution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and then
artificially aged.
T654 Solution heat-treated, stress-relieved by restriking cold in the finish die and then artificially aged.
T66 Solution heat-treated and then artificially aged - mechanical property level higher than T6 achieved through spe­
cial control of the process (6000 series alloys).
T7 Solution heat-treated and then artificially overaged.
T73 Solution heat-treated and then artificially overaged in order to achieve the best stress corrosion resistance.
T732 Solution heat-treated and then artificially overaged in order to achieve the best stress corrosion resistance.
Applies to test material heat-treated from annealed or F temper or to products heat-treated from any temper
by the user.
T7351 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to 3%
for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled ringand
then artificially overaged in order to achieve the best stress corrosion resistance. The products receive no further
straightening after stretching.
T73510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar,
shapes and tube, 0.5% to 3% for drawn tube) and then artificially overaged in order to achieve the best stress
corrosion resistance. The products receive no further straightening after stretching.
T73511 Same as T73510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T7352 Solution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and then artifi-
cially overaged in order to achieve the best stress corrosion resistance.
T7354 Solution heat-treated, stress-relieved by restriking cold in the finish die and then artificially overaged in order
to achieve the best stress corrosion resistance.

69
Technical Information

EN 515: 2000
Temper Definition
T74 Solution heat-treated and then artificially overaged (between T73 and T76).
T7451 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to 3%
for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled ring
and then artificially overaged (between T73 and T76). The products receive no further straightening after
stretching.
T74510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar
shapes and tube 0.5% to 3% for drawn tube) and then artificially overaged (between T73 and T76). The pro-
ducts receive no further straightening after stretching.
T74511 Same as T74510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T7452 Solution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and then artifi­
cially overaged (between T73 and T76).
T7454 Solution heat-treated, stress-relieved by restriking cold in the finish die and then artificially overaged (bet-
ween T73 and T76)
T76 Solution heat-treated and then artificially overaged in order to achieve a good exfoliation corrosion resistance.
T761 S olution heat-treated and then artificially overaged in order to achieve a good exfoliation corrosion resistan-
ce. (applies to 7475 sheet and strip).
T762 Solution heat-treated and then artificially overaged in order to achieve a good exfoliation corrosion resistan-
ce. Applies to test material heat-treated from annealed or F temper or to products heat-treated from any tem-
per by the user.
T7651 Solution heat-treated, stress-relieved by controlled stretching (permanent set 0.5% to 3% for sheet, 1.5% to
3% for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled
ring and then artificially overaged in order to achieve a good exfoliation corrosion resistance. The products
receive no further straightening after stretching.
T76510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar,
shapes and tube, 0.5% to 3% for drawn tube) and then artificially overaged in order to achieve a good exfoli-
ation corrosion resistance. The products receive no further straightening after stretching.
T76511 Same as T76510 except that minor straightening is allowed after stretching to comply with standard tolerances.
T7652 S olution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and then artifi­
cially overaged in order to achieve a good exfoliation corrosion resistance.
T7654 Solution heat-treated, stress-relieved by restriking in the finish die and then artificially overaged in order
to achieve a good exfoliation corrosion resistance.
T79 Solution heat-treated and then artificially overaged (very limited overageing).
T79510 S olution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar,
shapes and tube, 0.5% to 3% for drawn tube) and then artificially overaged (very limited overageing). The
products receive no further straightening after stretching.
T79511 Same as T79510 except for minor straightening is allowed after stretching to comply with standard tolerances.
T86) Solution heat-treated, cold worked and then artificially aged.
T81 Solution heat-treated, cold worked and then approximately 1% and then artificially aged.
T82 Solution heat-treated by the user, controlled stretched with a minimum permanent set of 2% and then artifi­-
cially aged (alloy 8090).
T832 Solution heat-treated, cold worked a controlled specific amount and then artificially aged (applies to 6063
drawn tube).
T841 Solution heat-treated, cold worked and then artificially underaged (sheet and strip in alloys 2091 and 8090).
T84151 Solution heat-treated, stress-relieved by stretching with a permanent set of 1.5% to 3% and then artificially
underaged (plate in alloys 2091 and 8090).
T851 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for sheet, 1.5% to 3%
for plate, 1% to 3% for rolled or cold-finished rod and bar, 1% to 5% for hand or ring forging and rolled ring)
and then artificially aged. The products receive no further straightening after stretching.
T8510 Solution heat-treated, stress-relieved by controlled stretching (permanent set 1% to 3% for extruded rod, bar,
profiles and tube, 0.5% to 3% for drawn tube) and then artificially aged. The products receive no further
straightening after stretching.
T8511 Same as T8510 except for minor straightening is allowed after stretching to comply with standard tolerances.
T852 S olution heat-treated, stress-relieved by compressing to produce a permanent set of 1% to 5% and then artifi­
cially aged.
T854 Solution heat-treated, stress-relieved by restriking cold in the finish die and then artificially aged.
T86 Solution heat-treated, cold worked approximately 6% and then artificially aged.
T87 Solution heat-treated, cold worked approximately 7% and then artificially aged.
T89 S olution heat-treated, cold worked to an appropriate degree to achieve the specified mechanical properties
and then artificially aged.
T9 Solution heat-treated, artificially aged and then cold worked.

70
Terms of Sale and Delivery

1. Validity 9. Retention of Title quality of the goods. If Buyer has discovered or

The present Terms of Sale and Delivery shall apply Seller shall retain title to the goods sold with the should have discovered the defect, and he does not
to all quotations, sales and deliveries unless other­ restrictions that follow from mandatory rules of submit a complaint in accordance with the above,
wise agreed in writing. law until the full purchase price plus any costs he cannot subsequently make a claim about the
Any terms of sale and delivery which may be accrued have been paid to Seller or to the party to defect.
printed on the order confirmation or to which the whom Seller has assigned his right. If Buyer has not made a claim about the defect to
customer otherwise refers shall only be valid if this Seller within 6 months from the date of delivery, he
is expressly stated in our order confirmation. 10. Delivery cannot subsequently claim any such defect.
Delivery shall be made from Seller´s address If remedial action has been taken or a replacement
2. Product Information whether or not Seller delivers the goods sold to delivery has been made, Seller´s liability for defects
All information about weight, dimensions and Buyer using his own employees or third party in cannot be extended to more than 1 year from the
quality as well as technical data and other data accordance with a separate agreement. The time of original date of delivery.
stated in catalogues, prospectuses and any other de­livery has been fixed by Seller at Seller´s best esti­
advertising material shall be directional and shall mate with the reservations made when the quota­ 15. Limitation of Liability
only be binding to the extent they form an express tion was given/the agreement was entered into. A claim for damages against Seller cannot exceed
part of the agreement between the parties. In connection with sale of goods from stock and the invoice amount for the product sold.
standard goods, a postponement of the time of Seller shall not be liable for any consequential loss,
3. Quotations delivery by 30 days due to Seller´s situation shall be loss of profit or any other indirect loss which follows
All prices shall be subject to changes in raw material regarded as delivery in due time and shall be from the agreement, including any indirect loss
and exchange rates, delivery time subject to the respected to the effect that Buyer cannot exercise which has incurred as a result of delay or defe­cts in
goods being unsold and change of delivery time any remedies against Seller for this reason unless the goods sold. The following circumstances shall
from works. If all Seller gives a written quo­tation otherwise agreed. result in exemption of liability for Seller if they pre­
which does not state a specific time stipulated for In connection with sale of individually manufac­ vent performance of the agreement or make the
acceptance, the quotation shall lapse if acceptance tured goods, Seller shall not be liable for any form performance of the agreement unnecessarily oner­
has not been received by the Seller within 2 weeks of delay irrespective of the duration hereof to the ous.
from the date of quotation. effect that Buyer cannot exercise any remedies Industrial disputes and any other circumstances
against Seller for this reason. Each of the parties beyond the control of the parties such as fire, war,
4. Quality shall, however, be entitled, without any liability, to mobilisation or unforeseen military call-ups of an
Buyer shall be responsible for ensuring that the cancel the agreement if the delay exceeds three equivalent extent, requisitioning, sequestration,
technical data and the material in its entirety are months. exchange controls, riots and civil unrest, shortage
suitable for his requirements. If a delay in delivery is due to Seller being in a situ­ of transport possibilities, general scarcity of goods,
A certificate will as agreed be enclosed in accor­ ation as stated in Clause 15 (exemption from liabil­ fuel restrictions and defects in or delays in deliver­
dance with agreement. Seller will check that the ity), the time of delivery shall be postponed by the ies from sub-suppliers which are due to any of the
certificate meets the demands for the delivery but time of duration of the obstacle. However, both circumstances set out in the present Clause.
will not check the information provided in the cer­ parties shall, without any liability, be entitled to Circumstances like those set out above which
tificate. cancel the agreement if the obstacle has lasted for occured before the quotation was given/the
more than 3 months. The present provision shall agreement was entered into shall only entail
5. Quantity apply whether or not the cause of delay occurs exemption of liability if their effect on the perfor­
The total quantity delivered shall be subject to a before or after the expiry of the agreed delivery mance of the agreement could not have beeen
margin of plus/minus 10% of the quantity specified. time. foreseen at the time in question.
Calculation by weight, unit or length shall be in In the above case, Seller shall notify Buyer of the Seller shall be under an obligation to notify Buyer
accordance with generally accepted practice. change in delivery time without undue delay. in writing without undue delay should any such
circumstances occur.
6. Orders and agreement 11. Packaging
In order to be binding on Seller, an order shall be Packaging shall be on Buyer´s account unless it is 16. Product Liability
confirmed in writing by Seller, and only Seller´s expressly stated that this has been included in the Seller shall only be liable for personal injury if it is
Terms of Sale and Delivery shall apply to the price. proved that the injury was suffered as a result of
exe­cution of the order. Packaging may only be returned in accordance errors or omissions on the part of Seller or other
If Buyer has any objections to the contents of the with a separate agreement. parties for whom, Seller is responsible.
order confirmation these shall be made in writing Seller shall not be liable for any damage to real
and shall be received by Seller not later than one 12. Cancellation property or movable property.
week after the date of the order confirmation. In connection with cancellation of deliveries, Buyer Seller shall not be liable for any consequential loss,
shall be under an obligation to pay full compensa­ loss of earnings or any other indirect loss.
7. Prices and Delivery tion, including for loss of profit, and gene­rally to To the extent to which Seller may incur product
In connection with sales from stock, the prices excl. indemnify Seller for all costs incurred in connection liability vis-à-vis a third party, Buyer shall be under
VAT and terms of payment are stated in Seller´s cur­ with the cancellation. an obligation to indemnify Seller to the same
rent price list in force at the time in question shall extent as Seller´s liability is limited in accordance
apply. Delivery shall be ex Seller´s address. 13. Product changes with the above three sentences. If a third party
Freigt payable by Buyer shall always be invoiced Seller reserves the right to make changes to agreed makes a claim against one of the parties for liability
Buyer and shall not be paid in cash on receipt. specifications without notice if this can be done for damages in accordance with the
witout any inconvenience to the Buyer. present Clause the party in question shall immedi­
8. Payment ately notify the other party.
Seller shall receive payment on the date specified in 14. Defects and Complaints Seller and Buyer shall be under a mutual obligation
the invoice as the final due date for payment. If Upon delivery, Buyer shall immediately perform to accept that legal proceedings are instituted
such a date has not been specified payment shall be such inspection of the goods sold as generally against them at the court which hears claims for
made in cash on delivery. However, Seller reser­ves accepted business practice requires. Any defects in damages brought against one of them on the basis
the right to change the terms of payment if Seller the goods sold will, within a reasonable period of of damage or injury allegedly caused by the deliv­
receives information that Buyer´s ability to pay has time, be remedied or a replacement delivery will be ery.
deteriorated. If the delivery is postponed because made at Seller´s discretion. These limitations to Seller´s liability shall not apply
of Buyer´s situation (claimant´s default), Buyer shall If such remedial action is not taken or a replace­ if he has shown gross negligence.
nevertheless, unless otherwise notified by Seller, be ment delivery is not made within a reasonable
under an obligation to make any payment to Seller period of time, Buyer shall be entitled to termina­te 17. Returns
as if delivery had been made at the agreed time. If the agreement, require a reduction in the pur­ Returns will only be accepted in accordance with a
payment is made after the due date, Seller shall be chase price or claim damages pursuant to with the special agreement on this with Seller.
entitled to charge interest on the outstanding general rules of Danish law and the present Terms Unless otherwise agreed, crediting of returns shall
amount from time to time from the due date at the of Sale and Delivery. be subject to the returns being undamaged and as
rate of interest stated on the invoice at any given If Buyer wants to claim a defect, Buyer shall notify for works/factory-packaged materials that they are
time. Buyer shall not be entitled to offset any coun­ Seller hereof in writing immediately after the in original, unbroken packaging.
terclaims against Seller which have not been recog­ defect has been or should have been discovered
nized in writing by Seller and shall not be entitled and specify the nature of the defect in the written 18. Disputes
to withhold any part of the purchase price because notification. Samples of a sufficient quantity for a Any disputes arising between the parties shall be
of countercla­ims of any kind whatsoever. certain assessment of the justification of the com­ settled by the courts in Denmark pursuant to
plaints must be enclosed with complaints about the Danish law.

71
 Reservations are taken for printing errors. Photos ©: Alumeco A/S

Alumeco A/S Naesbyvej 26 DK-5000 Odense C Tlf. +45 66 17 81 17 Fax +45 66 14 58 71 [email protected] www.alumeco.com