RAINBOW HEIGHTS RADIO SITE INFRASTRUCTURE REPLACEMENT PROJECT

STRUCTURAL CALCULATIONS
 Table of Contents
Description Page

Design Scope 1

Section A: Calculations for Tower Foundation

Design Criteria 3
Load Parameters 3-4
Tower Load Summary 5
tnxTower Report 6 - 26
Foundation Design 27 - 37

Section B: Calculations for Equipment Building Foundation and Anchorage

Design Criteria 39
Loads 39 - 42
Foundation, Anchorage and Embed Plate Design 43 - 56

Section C: Calculation Attachments

Attachment #1: ATC Windspeed 58
Attachment #2: Google Earth Elevation Profile 59

Appendix A:
Owner-Provided Appurtenance List and Equipment Data Sheets 60 – 77

Appendix B:
Geotechnical Investigation Letter Report for the “Proposed Control Shelter
and Communications Tower,” by AECOM, dated July 13, 2017 78 - 90

i
Design Scope:

· Design of new tower foundation to replace existing 40’ high (approx.) tower. The design
of the tower and anchorage is per the tower manufacturer. A preliminary tower analysis
was performed to estimate loads for the foundation design. The foundation is designed
to accommodate a 25% future load increase on the new tower.

· Design of new foundation and anchorage for a re-purposed precast building structure
(16’L x 10’W x 9’H) being supplied by the County.

Page 1
 SECTION A:

CALCULATIONS FOR
TOWER FOUNDATION

Page 2
(PER TIA-222 SECTION 2.8.3)

Page 3
Page 4
Rainbow Tower Load Summary Table
Antenna Aspect
Attachment Approx Total Length of Pipes in Mount Member Mount Member Ratio Ca (Round,
2
level Owner Antenna Location Azimuth Antenna Make or Size Antenna Wt. (lb) Antenna Length, L (ft) Antenna Width, W (in) Aspect Ratio (L/W) Ca (Round, Subcritical) Aa (ft ) 2
Aa*Ca (ft ) Mount Type/ Size Standoff Mount (ft) Mount Wt. (lb) Length, L (ft) Width, W (in) (L/W) Subcritical) Aa (ft2) Aa*Ca (ft2)
Telewave/ 256" Omni Antenna
40' SD County LEG #1 N/A 35 21.33 2.75 93.08 1.20 4.89 5.87 2' standoff Pipe to Pipe/ 2-3/8" OD pipe 8.00 29.28 2.00 2.38 10.11 0.87 1.58 1.38
6dBd Fiberglass Collinear Antenna
Telewave/ 256" Omni Antenna
40' SD County LEG #2 N/A 35 21.33 2.75 93.08 1.20 4.89 5.87 2' standoff Pipe to Pipe/ 2-3/8" OD pipe 8.00 29.28 2.00 2.38 10.11 0.87 1.58 1.38
6dBd Fiberglass Collinear Antenna
Telewave/ 256" Omni Antenna
40' SD County LEG #3 N/A 35 21.33 2.75 93.08 1.20 4.89 5.87 2' standoff Pipe to Pipe/ 2-3/8" OD pipe 8.00 29.28 2.00 2.38 10.11 0.87 1.58 1.38
6dBd Fiberglass Collinear Antenna
30' SD County LEG #2 N/A 8' - 0" x 2" Dipole Antenna 30 8 4 24.00 1.20 2.67 3.20 1' standoff Pipe to Pipe/ 2-3/8" OD pipe 4.00 14.64 3.00 2.38 15.16 0.98 0.79 0.78
30' SD County LEG #1 N/A 5' - 6" x 2" Dipole Antenna 20 5.5 4 16.50 1.20 1.83 2.20 1' standoff Pipe to Pipe/ 2-3/8" OD pipe 4.00 14.64 3.00 2.38 15.16 0.98 0.79 0.78
20' SD County LEG #2 N/A Hustler Omni Antenna 7' 6" 10 8.5 2 51.00 1.20 1.42 1.70 4' standoff Pipe to Pipe/ 2-3/8" OD pipe 10.00 36.60 4.00 2.38 20.21 1.09 1.98 2.16
Center 20 SD County LEG #1 160 Decible Yagi Antenna 15 3 6 6.00 1.20 1.50 1.80 1' standoff Pipe to Pipe/ 2-3/8" OD pipe 3.00 10.98 3.00 2.38 15.16 0.98 0.59 0.58
18' SD County LEG #1 N/A Telewave Omni Antenna 244" 30 20.33 2.75 88.71 1.20 4.66 5.59 4' standoff Pipe to Pipe/ 2-3/8" OD pipe 10.00 36.60 4.00 2.38 20.21 1.09 1.98 2.16
18 SD County LEG #3 N/A Telewave Omni Antenna 244" 30 20.33 2.75 88.71 1.20 4.66 5.59 4' standoff Pipe to Pipe/ 2-3/8" OD pipe 10.00 36.60 4.00 2.38 20.21 1.09 1.98 2.16
Center 12' SD County LEG #1 & #2 face mount 195 Andrew MW Antennaa 8' parabolic 350 8 50.27 1' to 2' standoff Pipe to Pipe/ 3-1/2" OD pipe 4.00 30.32 4.00 3.50 13.71 0.95 1.17 1.11
10' SD County LEG #1 N/A Trimble GPS Antenna 1' 5 1.5 1 18.00 1.20 0.13 0.15 2' standoff Pipe to Pipe/ 2-7/8" OD pipe 3.00 17.40 3.00 2.88 12.52 0.92 0.72 0.66

Notes:
1) Tower appurtenances based on owner-provided list (See Appendix A)
2) Additional loading considerations:
a) 10' Lightning Rod @ 40' height
b) 3/8" Diam Safety Line, full height
c) Waveguide Ladder

Page 5
 Lightning
8'
5'-6"
Hustler
Decibel
Telewave
2"
3"
Andrew
2.5"
Trimble
xStd
2"
Std
x Dipole
Pipe
2"
102"
GPS
Yagi
8'
Pipe
Dipole
Rod
256"
244"
MW-Omni
1'
4'
2'
- w/
2'
Omni
Standoff
Standoff
Radome 40
30
20
18
12
10
DESIGNED APPURTENANCE LOADING
TYPE ELEVATION TYPE ELEVATION
Telewave 256" Omni 40 Decibel Yagi 20
Telewave 256" Omni 40 2" Std Pipe - 4' Standoff 20
Telewave 256" Omni 40 2" Std Pipe - 1' Standoff 20
Lightning Rod 40 Telewave 244" Omni 18
2" Std Pipe - 2' Standoff 40 Telewave 244" Omni 18
2" Std Pipe - 2' Standoff 40 2" Std Pipe - 4' Standoff 18
2" Std Pipe - 2' Standoff 40 2" Std Pipe - 4' Standoff 18
8' x 2" Dipole 30 3" Std Pipe - 2' Standoff 12
5'-6" x 2" Dipole 30 Andrew 8' MW w/ Radome 12
2" Std Pipe - 1' Standoff 30 2.5" Std Pipe - 2' Standoff 10
2" Std Pipe - 1' Standoff 30 Trimble GPS 10
Hustler 102" Omni 20

MATERIAL STRENGTH
GRADE Fy Fu GRADE Fy Fu
A36 36 ksi 58 ksi

TOWER DESIGN NOTES

1. Tower designed for Exposure C to the TIA-222-G Standard.
40.0 ft
2. Tower designed for a 115 mph basic wind in accordance with the TIA-222-G Standard.
3. Deflections are based upon a 60 mph wind.
4. Tower Risk Category III and IV.
5. Topographic Category 3 with Crest Height of 1100.00 ft
6. Weld together tower sections have flange connections.
7. Connections use galvanized A325 bolts, nuts and locking devices. Installation per TIA/EIA-222
and AISC Specifications.
8. Tower members are "hot dipped" galvanized in accordance with ASTM A123 and ASTM A153
Standards.
9. Welds are fabricated with ER-70S-6 electrodes.
L1 1/2x1 1/2x1/8
SR 1 5/8

617.9
T1

L1 1/2x1 1/2x1/8

10 @ 4

20.0 ft
A36

A36

ALL REACTIONS
ARE FACTORED
L2x2x1/4
SR 2 3/4

MAX. CORNER REACTIONS AT BASE:

1702.4
T2

DOWN: 94158 lb
SHEAR: 6220 lb
Maximum resultant moment and shear
UPLIFT: -83920 lb reactions due to 0.9DL+WL(0 deg)
SHEAR: 5390 lb load case (Load Case 1)
AXIAL
(see page 13 of 20 of tnxTower report)
4280 lb
Additionally, a second load case due
SHEAR MOMENT to 0.9DL+WL(30 deg) is also consid-
11138 lb 241096 lb-ft
0.0 ft
ered for biaxial loading on footing
Weight (lb) 2320.3

TORQUE 5362 lb-ft (Load Case 2)

REACTIONS - 115 mph WIND
Diagonal Grade

# Panels @ (ft)
Face Width (ft)

(see page 13 of 20 of tnxTower report)

Leg Grade

Diagonals

Top Girts
Section

Legs

Job:
AECOM Rainbow Tower
Project:
4225 Executive Square, Ste. 1400 Client:
La Jolla, CA 92037 County of San Diego Drawn by: David Hollinger App'd:
Code: Date: Scale:
Page Phone:
6 (858) 812-9292 TIA-222-G 07/24/17 NTS
Path: Dwg No.
FAX: - E-1
U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\TnxTower Analysis\Rainbow Tower v.1.eri
 Job Page
tnxTower Rainbow Tower 1 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Input Data

The main tower is a 3x free standing tower with an overall height of 40.00 ft above the ground line.
The base of the tower is set at an elevation of 0.00 ft above the ground line.
The face width of the tower is 3.00 ft at the top and 3.00 ft at the base.
This tower is designed using the TIA-222-G standard.
The following design criteria apply:
ASCE 7-10 Wind Data is used.
Basic wind speed of 115 mph.
Risk Category III and IV.
Exposure Category C.
Topographic Category 3.
Crest Height 1100.00 ft.
Deflections calculated using a wind speed of 60 mph.
Weld together tower sections have flange connections..
Connections use galvanized A325 bolts, nuts and locking devices. Installation per TIA/EIA-222 and AISC
Specifications..
Tower members are ''hot dipped'' galvanized in accordance with ASTM A123 and ASTM A153 Standards..
Welds are fabricated with ER-70S-6 electrodes..
A non-linear (P-delta) analysis was used.
Pressures are calculated at each section.
Stress ratio used in tower member design is 1.
Local bending stresses due to climbing loads, feed line supports, and appurtenance mounts are not considered.

Options
Consider Moments - Legs Distribute Leg Loads As Uniform Use ASCE 10 X-Brace Ly Rules
Consider Moments - Horizontals Assume Legs Pinned √ Calculate Redundant Bracing Forces
Consider Moments - Diagonals √ Assume Rigid Index Plate Ignore Redundant Members in FEA
Use Moment Magnification √ Use Clear Spans For Wind Area SR Leg Bolts Resist Compression
√ Use Code Stress Ratios √ Use Clear Spans For KL/r √ All Leg Panels Have Same Allowable
√ Use Code Safety Factors - Guys Retension Guys To Initial Tension Offset Girt At Foundation
Escalate Ice Bypass Mast Stability Checks Consider Feed Line Torque
Always Use Max Kz √ Use Azimuth Dish Coefficients √ Include Angle Block Shear Check
Use Special Wind Profile √ Project Wind Area of Appurt. Use TIA-222-G Bracing Resist. Exemption
√ Include Bolts In Member Capacity √ Autocalc Torque Arm Areas Use TIA-222-G Tension Splice Exemption
√ Leg Bolts Are At Top Of Section Add IBC .6D+W Combination Poles
√ Secondary Horizontal Braces Leg √ Sort Capacity Reports By Component Include Shear-Torsion Interaction
Use Diamond Inner Bracing (4 Sided) Triangulate Diamond Inner Bracing Always Use Sub-Critical Flow
SR Members Have Cut Ends Treat Feed Line Bundles As Cylinder Use Top Mounted Sockets
SR Members Are Concentric

Page 7
 Job Page
tnxTower Rainbow Tower 2 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Wind 180

Leg A

Wind 90

Fa
eA

ce
c
Fa

B
X
Leg C Z Leg B

Fac e C

Wind Norma l

Triangular To wer

Tower Section Geometry

Tower Tower Assembly Description Section Number Section
Section Elevation Database Width of Length
Sections
ft ft ft
T1 40.00-20.00 3.00 1 20.00
T2 20.00-0.00 3.00 1 20.00

Tower Section Geometry (cont’d)

Tower Tower Diagonal Bracing Has Has Top Girt Bottom Girt
Section Elevation Spacing Type K Brace Horizontals Offset Offset
End
ft ft Panels in in
T1 40.00-20.00 4.00 X Brace No No 0.0000 0.0000
T2 20.00-0.00 4.00 X Brace No No 0.0000 0.0000

Tower Section Geometry (cont’d)

Tower Leg Leg Leg Diagonal Diagonal Diagonal
Elevation Type Size Grade Type Size Grade
ft
T1 40.00-20.00 Solid Round 1 5/8 A36 Equal Angle L1 1/2x1 1/2x1/8 A36

Page 8
 Job Page
tnxTower Rainbow Tower 3 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Leg Leg Leg Diagonal Diagonal Diagonal

Elevation Type Size Grade Type Size Grade
ft
(36 ksi) (36 ksi)
T2 20.00-0.00 Solid Round 2 3/4 A36 Equal Angle L2x2x1/4 A36
(36 ksi) (36 ksi)

Tower Section Geometry (cont’d)

Tower Top Girt Top Girt Top Girt Bottom Girt Bottom Girt Bottom Girt
Elevation Type Size Grade Type Size Grade
ft
T1 40.00-20.00 Equal Angle L1 1/2x1 1/2x1/8 A36 Solid Round A36
(36 ksi) (36 ksi)
T2 20.00-0.00 Equal Angle L1 1/2x1 1/2x1/8 A36 Solid Round A36
(36 ksi) (36 ksi)

Tower Section Geometry (cont’d)

Tower Gusset Gusset Gusset Grade Adjust. Factor Adjust. Weight Mult. Double Angle Double Angle Double Angle
Elevation Area Thickness Af Factor Stitch Bolt Stitch Bolt Stitch Bolt
(per face) Ar Spacing Spacing Spacing
Diagonals Horizontals Redundants
ft ft2 in in in in
T1 40.00-20.00 0.00 0.0000 A36 1 1 1 36.0000 36.0000 36.0000
(36 ksi)
T2 20.00-0.00 0.00 0.0000 A36 1 1 1 36.0000 36.0000 36.0000
(36 ksi)

Tower Section Geometry (cont’d)

K Factors1
Tower Calc Calc Legs X K Single Girts Horiz. Sec. Inner
Elevation K K Brace Brace Diags Horiz. Brace
Single Solid Diags Diags
Angles Rounds X X X X X X X
ft Y Y Y Y Y Y Y
T1 No No 1 1 1 1 1 1 1 1
40.00-20.00 1 1 1 1 1 1 1
T2 20.00-0.00 No No 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
1
Note: K factors are applied to member segment lengths. K-braces without inner supporting members will have the K factor in the out-of-plane direction applied to
the overall length.

Tower Section Geometry (cont’d)

Page 9
 Job Page
tnxTower Rainbow Tower 4 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Leg Diagonal Top Girt Bottom Girt Mid Girt Long Horizontal Short Horizontal
Elevation
ft
Net Width U Net Width U Net Width U Net U Net U Net U Net U
Deduct Deduct Deduct Width Width Width Width
in in in Deduct Deduct Deduct Deduct
in in in in
T1 40.00-20.00 0.0000 1 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75
T2 20.00-0.00 0.0000 1 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75 0.0000 0.75

Tower Section Geometry (cont’d)

Tower Leg Leg Diagonal Top Girt Bottom Girt Mid Girt Long Horizontal Short Horizontal
Elevation Connection
ft Type
Bolt Size No. Bolt Size No. Bolt Size No. Bolt Size No. Bolt Size No. Bolt Size No. Bolt Size No.
in in in in in in in
T1 40.00-20.00 Flange 0.6250 4 0.6250 1 0.6250 0 0.6250 0 0.6250 0 0.6250 0 0.6250 0
A325N A325N A325N A325N A325N A325N A325N
T2 20.00-0.00 Flange 0.6250 4 0.6250 1 0.6250 0 0.6250 0 0.6250 0 0.6250 0 0.6250 0
A325N A325N A325N A325N A325N A325N A325N

Feed Line/Linear Appurtenances - Entered As Round Or Flat

Description Face Allow Component Placement Total Number Clear Width or Perimeter Weight
or Shield Type Number Per Row Spacing Diameter
Leg ft in in in plf
LDF5 B No Ar (CaAa) 40.00 - 8.00 3 3 0.5000 1.0800 0.30
0.0000
LDF5 B No Ar (CaAa) 30.00 - 8.00 2 2 0.5000 1.0800 0.30
0.0000
LDF5 B No Ar (CaAa) 20.00 - 8.00 2 2 0.5000 1.0800 0.30
0.0000
LDF5 B No Ar (CaAa) 18.00 - 8.00 2 2 0.5000 1.0800 0.30
0.0000
EW63 B No Ar (CaAa) 12.00 - 8.00 1 1 0.5000 2.0100 0.51
0.0000
LDF5 B No Ar (CaAa) 10.00 - 8.00 1 1 0.5000 1.0800 0.30
0.0000
3/8'' Safety Cable C No Ar (CaAa) 0.00 - 0.00 1 1 0.0000 0.3750 0.22

Feed Line/Linear Appurtenances - Entered As Area

Description Face Allow Component Placement Total CAAA Weight
or Shield Type Number
2
Leg ft ft /ft plf
Feedline Ladder B No CaAa (In Face) 40.00 - 8.00 1 No Ice 0.50 8.40

Feed Line/Linear Appurtenances Section Areas

Page 10
 Job Page
tnxTower Rainbow Tower 5 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Tower Face AR AF CAAA CAAA Weight

Section Elevation In Face Out Face
ft ft2 ft2 ft2 ft2 lb
T1 40.00-20.00 A 0.000 0.000 0.000 0.000 0.00
B 0.000 0.000 18.640 0.000 192.00
C 0.000 0.000 0.000 0.000 0.00
T2 20.00-0.00 A 0.000 0.000 0.000 0.000 0.00
B 0.000 0.000 18.224 0.000 134.64
C 0.000 0.000 0.000 0.000 0.00

Shielding Factor Ka
Tower Feed Line Description Feed Line Ka Ka
Section Record No. Segment Elev. No Ice Ice
T1 1 LDF5 20.00 - 40.00 0.6000 0.6000
T1 2 LDF5 20.00 - 30.00 0.6000 0.6000
T1 8 Feedline Ladder 20.00 - 40.00 1.0000 1.0000
T2 1 LDF5 8.00 - 20.00 0.6000 0.6000
T2 2 LDF5 8.00 - 20.00 0.6000 0.6000
T2 3 LDF5 8.00 - 20.00 0.6000 0.6000
T2 4 LDF5 8.00 - 18.00 0.6000 0.6000
T2 5 EW63 8.00 - 12.00 0.6000 0.6000
T2 6 LDF5 8.00 - 10.00 0.6000 0.6000
T2 8 Feedline Ladder 8.00 - 20.00 1.0000 1.0000

Discrete Tower Loads

Description Face Offset Offsets: Azimuth Placement CAAA CAAA Weight
or Type Horz Adjustment Front Side
Leg Lateral
Vert
ft ° ft ft2 ft2 lb
ft
ft
***Antennas***
Telewave 256'' Omni A From Leg 2.00 0.0000 40.00 No Ice 5.87 5.87 35.00
0.00
10.67
Telewave 256'' Omni B From Leg 2.00 0.0000 40.00 No Ice 5.87 5.87 35.00
0.00
10.67
Telewave 256'' Omni C From Leg 2.00 0.0000 40.00 No Ice 5.87 5.87 35.00
0.00
10.67
8' x 2'' Dipole C From Leg 1.00 0.0000 30.00 No Ice 3.20 3.20 30.00
0.00
0.00
5'-6'' x 2'' Dipole B From Leg 1.00 0.0000 30.00 No Ice 2.20 2.20 20.00
0.00
0.00
Hustler 102'' Omni C From Leg 4.00 0.0000 20.00 No Ice 1.70 1.70 10.00
0.00
4.25

Page 11
 Job Page
tnxTower Rainbow Tower 6 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Description Face Offset Offsets: Azimuth Placement CAAA CAAA Weight

or Type Horz Adjustment Front Side
Leg Lateral
Vert
ft ° ft ft2 ft2 lb
ft
ft
Decibel Yagi B From Leg 1.00 0.0000 20.00 No Ice 1.80 1.80 15.00
0.00
0.00
Telewave 244'' Omni B From Leg 4.00 0.0000 18.00 No Ice 5.59 5.59 30.00
0.00
10.17
Telewave 244'' Omni A From Leg 4.00 0.0000 18.00 No Ice 5.59 5.59 30.00
0.00
10.17
Trimble GPS B From Leg 1.00 0.0000 10.00 No Ice 0.15 0.15 5.00
0.00
0.00
Lightning Rod A From Leg 0.00 0.0000 40.00 No Ice 3.00 3.00 30.00
0.00
5.00
***Mounts***
2'' Std Pipe - 2' Standoff A From Leg 1.00 0.0000 40.00 No Ice 1.38 1.38 30.00
0.00
0.00
2'' Std Pipe - 2' Standoff B From Leg 1.00 0.0000 40.00 No Ice 1.38 1.38 30.00
0.00
0.00
2'' Std Pipe - 2' Standoff C From Leg 1.00 0.0000 40.00 No Ice 1.38 1.38 30.00
0.00
0.00
2'' Std Pipe - 1' Standoff C From Leg 0.50 0.0000 30.00 No Ice 0.78 0.78 15.00
0.00
0.00
2'' Std Pipe - 1' Standoff B From Leg 0.50 0.0000 30.00 No Ice 0.78 0.78 15.00
0.00
0.00
2'' Std Pipe - 4' Standoff C From Leg 2.00 0.0000 20.00 No Ice 2.16 2.16 37.00
0.00
0.00
2'' Std Pipe - 1' Standoff B From Leg 0.50 0.0000 20.00 No Ice 0.78 0.78 15.00
0.00
0.00
2'' Std Pipe - 4' Standoff B From Leg 2.00 0.0000 18.00 No Ice 2.16 2.16 37.00
0.00
0.00
2'' Std Pipe - 4' Standoff A From Leg 2.00 0.0000 18.00 No Ice 2.16 2.16 37.00
0.00
0.00
3'' Std Pipe - 2' Standoff C From Face 0.50 0.0000 12.00 No Ice 1.11 1.11 31.00
0.00
0.00
2.5'' Std Pipe - 2' Standoff B From Leg 1.00 0.0000 10.00 No Ice 0.66 0.66 18.00
0.00
0.00

Dishes

Page 12
 Job Page
tnxTower Rainbow Tower 7 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Description Face Dish Offset Offsets: Azimuth 3 dB Elevation Outside Aperture Weight
or Type Type Horz Adjustment Beam Diameter Area
Leg Lateral Width
Vert
ft ° ° ft ft ft2 lb
Andrew 8' MW w/ C Paraboloid w/o From 1.00 0.0000 12.00 8.00 No Ice 0.00 350.00
Radome Radome Face 0.00
0.00

Tower Pressures - No Ice

GH = 0.850

Section z KZ qz AG F AF AR Aleg Leg CAAA CAAA

Elevation a % In Out
c Face Face
ft ft psf ft2 e ft2 ft2 ft2 ft2 ft2
T1 40.00-20.00 30.00 0.982 64 62.708 A 6.326 5.417 5.417 46.13 0.000 0.000
B 6.326 5.417 46.13 18.640 0.000
C 6.326 5.417 46.13 0.000 0.000
T2 20.00-0.00 10.00 0.85 57 64.583 A 8.081 9.167 9.167 53.15 0.000 0.000
B 8.081 9.167 53.15 18.224 0.000
C 8.081 9.167 53.15 0.000 0.000

Tower Pressure - Service

GH = 0.850

Section z KZ qz AG F AF AR Aleg Leg CAAA CAAA

Elevation a % In Out
c Face Face
ft ft psf ft2 e ft2 ft2 ft2 ft2 ft2
T1 40.00-20.00 30.00 0.982 17 62.708 A 6.326 5.417 5.417 46.13 0.000 0.000
B 6.326 5.417 46.13 18.640 0.000
C 6.326 5.417 46.13 0.000 0.000
T2 20.00-0.00 10.00 0.85 15 64.583 A 8.081 9.167 9.167 53.15 0.000 0.000
B 8.081 9.167 53.15 18.224 0.000
C 8.081 9.167 53.15 0.000 0.000

Tower Forces - No Ice - Wind Normal To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 64 1 1 9.426 2171.10 108.56 C
40.00-20.00 B 0.187 2.639 1 1 9.426
C 0.187 2.639 1 1 9.426
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 57 1 1 13.338 2171.45 108.57 C
B 0.267 2.387 1 1 13.338
C 0.267 2.387 1 1 13.338
Sum Weight: 326.64 2320.31 OTM 86847.64 4342.56
lb-ft

Page 13
 Job Page
tnxTower Rainbow Tower 8 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Forces - No Ice - Wind 60 To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 64 0.8 1 8.161 1990.15 99.51 C
40.00-20.00 B 0.187 2.639 0.8 1 8.161
C 0.187 2.639 0.8 1 8.161
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 57 0.8 1 11.722 1986.00 99.30 C
B 0.267 2.387 0.8 1 11.722
C 0.267 2.387 0.8 1 11.722
Sum Weight: 326.64 2320.31 OTM 79564.43 3976.15
lb-ft

Tower Forces - No Ice - Wind 90 To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 64 0.85 1 8.477 2035.39 101.77 C
40.00-20.00 B 0.187 2.639 0.85 1 8.477
C 0.187 2.639 0.85 1 8.477
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 57 0.85 1 12.126 2032.36 101.62 C
B 0.267 2.387 0.85 1 12.126
C 0.267 2.387 0.85 1 12.126
Sum Weight: 326.64 2320.31 OTM 81385.24 4067.75
lb-ft

Tower Forces - Service - Wind Normal To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 17 1 1 9.426 591.00 29.55 C
40.00-20.00 B 0.187 2.639 1 1 9.426
C 0.187 2.639 1 1 9.426
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 15 1 1 13.338 591.09 29.55 C
B 0.267 2.387 1 1 13.338
C 0.267 2.387 1 1 13.338
Sum Weight: 326.64 2320.31 OTM 23640.95 1182.09
lb-ft

Page 14
 Job Page
tnxTower Rainbow Tower 9 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Tower Forces - Service - Wind 60 To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 17 0.8 1 8.161 541.74 27.09 C
40.00-20.00 B 0.187 2.639 0.8 1 8.161
C 0.187 2.639 0.8 1 8.161
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 15 0.8 1 11.722 540.61 27.03 C
B 0.267 2.387 0.8 1 11.722
C 0.267 2.387 0.8 1 11.722
Sum Weight: 326.64 2320.31 OTM 21658.37 1082.35
lb-ft

Tower Forces - Service - Wind 90 To Face

Section Add Self F e CF qz DF DR AE F w Ctrl.
Elevation Weight Weight a Face
c psf
ft lb lb e ft2 lb plf
T1 192.00 617.87 A 0.187 2.639 17 0.85 1 8.477 554.06 27.70 C
40.00-20.00 B 0.187 2.639 0.85 1 8.477
C 0.187 2.639 0.85 1 8.477
T2 20.00-0.00 134.64 1702.44 A 0.267 2.387 15 0.85 1 12.126 553.23 27.66 C
B 0.267 2.387 0.85 1 12.126
C 0.267 2.387 0.85 1 12.126
Sum Weight: 326.64 2320.31 OTM 22154.02 1107.29
lb-ft

Discrete Appurtenance Pressures - No Ice GH = 0.850

Description Aiming Weight Offsetx Offsetz z Kz qz CAAC CAAC

Azimuth Front Side
° lb ft ft ft psf ft2 ft2
Telewave 256'' Omni 0.0000 35.00 0.00 -3.73 50.67 1.097 69 5.87 5.87
Telewave 256'' Omni 120.0000 35.00 3.23 1.87 50.67 1.097 69 5.87 5.87
Telewave 256'' Omni 240.0000 35.00 -3.23 1.87 50.67 1.097 69 5.87 5.87
8' x 2'' Dipole 240.0000 30.00 -2.37 1.37 30.00 0.982 64 3.20 3.20
5'-6'' x 2'' Dipole 120.0000 20.00 2.37 1.37 30.00 0.982 64 2.20 2.20
Hustler 102'' Omni 240.0000 10.00 -4.96 2.87 24.25 0.939 61 1.70 1.70
Decibel Yagi 120.0000 15.00 2.37 1.37 20.00 0.902 59 1.80 1.80
Telewave 244'' Omni 120.0000 30.00 4.96 2.87 28.17 0.969 63 5.59 5.59
Telewave 244'' Omni 0.0000 30.00 0.00 -5.73 28.17 0.969 63 5.59 5.59
Trimble GPS 120.0000 5.00 2.37 1.37 10.00 0.850 57 0.15 0.15
Lightning Rod 0.0000 30.00 0.00 -1.73 45.00 1.070 68 3.00 3.00
2'' Std Pipe - 2' Standoff 0.0000 30.00 0.00 -2.73 40.00 1.044 67 1.38 1.38
2'' Std Pipe - 2' Standoff 120.0000 30.00 2.37 1.37 40.00 1.044 67 1.38 1.38
2'' Std Pipe - 2' Standoff 240.0000 30.00 -2.37 1.37 40.00 1.044 67 1.38 1.38

Page 15
 Job Page
tnxTower Rainbow Tower 10 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Description Aiming Weight Offsetx Offsetz z Kz qz CAAC CAAC

Azimuth Front Side
° lb ft ft ft psf ft2 ft2
2'' Std Pipe - 1' Standoff 240.0000 15.00 -1.93 1.12 30.00 0.982 64 0.78 0.78
2'' Std Pipe - 1' Standoff 120.0000 15.00 1.93 1.12 30.00 0.982 64 0.78 0.78
2'' Std Pipe - 4' Standoff 240.0000 37.00 -3.23 1.87 20.00 0.902 59 2.16 2.16
2'' Std Pipe - 1' Standoff 120.0000 15.00 1.93 1.12 20.00 0.902 59 0.78 0.78
2'' Std Pipe - 4' Standoff 120.0000 37.00 3.23 1.87 18.00 0.882 58 2.16 2.16
2'' Std Pipe - 4' Standoff 0.0000 37.00 0.00 -3.73 18.00 0.882 58 2.16 2.16
3'' Std Pipe - 2' Standoff 180.0000 31.00 0.00 1.37 12.00 0.850 56 1.11 1.11
2.5'' Std Pipe - 2' 120.0000 18.00 2.37 1.37 10.00 0.850 57 0.66 0.66
Standoff
Sum 570.00
Weight:

Discrete Appurtenance Pressures - Service GH = 0.850

Description Aiming Weight Offsetx Offsetz z Kz qz CAAC CAAC

Azimuth Front Side
° lb ft ft ft psf ft2 ft2
Telewave 256'' Omni 0.0000 35.00 0.00 -3.73 50.67 1.097 19 5.87 5.87
Telewave 256'' Omni 120.0000 35.00 3.23 1.87 50.67 1.097 19 5.87 5.87
Telewave 256'' Omni 240.0000 35.00 -3.23 1.87 50.67 1.097 19 5.87 5.87
8' x 2'' Dipole 240.0000 30.00 -2.37 1.37 30.00 0.982 17 3.20 3.20
5'-6'' x 2'' Dipole 120.0000 20.00 2.37 1.37 30.00 0.982 17 2.20 2.20
Hustler 102'' Omni 240.0000 10.00 -4.96 2.87 24.25 0.939 17 1.70 1.70
Decibel Yagi 120.0000 15.00 2.37 1.37 20.00 0.902 16 1.80 1.80
Telewave 244'' Omni 120.0000 30.00 4.96 2.87 28.17 0.969 17 5.59 5.59
Telewave 244'' Omni 0.0000 30.00 0.00 -5.73 28.17 0.969 17 5.59 5.59
Trimble GPS 120.0000 5.00 2.37 1.37 10.00 0.850 15 0.15 0.15
Lightning Rod 0.0000 30.00 0.00 -1.73 45.00 1.070 19 3.00 3.00
2'' Std Pipe - 2' Standoff 0.0000 30.00 0.00 -2.73 40.00 1.044 18 1.38 1.38
2'' Std Pipe - 2' Standoff 120.0000 30.00 2.37 1.37 40.00 1.044 18 1.38 1.38
2'' Std Pipe - 2' Standoff 240.0000 30.00 -2.37 1.37 40.00 1.044 18 1.38 1.38
2'' Std Pipe - 1' Standoff 240.0000 15.00 -1.93 1.12 30.00 0.982 17 0.78 0.78
2'' Std Pipe - 1' Standoff 120.0000 15.00 1.93 1.12 30.00 0.982 17 0.78 0.78
2'' Std Pipe - 4' Standoff 240.0000 37.00 -3.23 1.87 20.00 0.902 16 2.16 2.16
2'' Std Pipe - 1' Standoff 120.0000 15.00 1.93 1.12 20.00 0.902 16 0.78 0.78
2'' Std Pipe - 4' Standoff 120.0000 37.00 3.23 1.87 18.00 0.882 16 2.16 2.16
2'' Std Pipe - 4' Standoff 0.0000 37.00 0.00 -3.73 18.00 0.882 16 2.16 2.16
3'' Std Pipe - 2' Standoff 180.0000 31.00 0.00 1.37 12.00 0.850 15 1.11 1.11
2.5'' Std Pipe - 2' 120.0000 18.00 2.37 1.37 10.00 0.850 15 0.66 0.66
Standoff
Sum 570.00
Weight:

Dish Pressures - No Ice

Elevation Dish Aiming Weight Offsetx Offsetz Kz AA qz
ft Description Azimuth lb ft ft ft2 psf
°
12.00 Andrew 8' MW w/ Radome 180.0000 350.00 0.00 1.87 0.850 50.27 56
Sum 350.00
Weight:

Page 16
 Job Page
tnxTower Rainbow Tower 11 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Dish Pressures - Service

Elevation Dish Aiming Weight Offsetx Offsetz Kz AA qz
ft Description Azimuth lb ft ft ft2 psf
°
12.00 Andrew 8' MW w/ Radome 180.0000 350.00 0.00 1.87 0.850 50.27 15
Sum 350.00
Weight:

Force Totals
Load Vertical Sum of Sum of Sum of Sum of Sum of Torques
Case Forces Forces Forces Overturning Overturning
X Z Moments, Mx Moments, Mz
lb lb lb lb-ft lb-ft lb-ft
Leg Weight 1636.09
Bracing Weight 684.21
Total Member Self-Weight 2320.31 756.61 -194.53
Total Weight 3566.95 756.61 -194.53
Wind 0 deg - No Ice 0.00 -11138.50 -240855.70 -194.53 1294.50
Wind 30 deg - No Ice 3487.80 -9918.37 -209876.89 -94940.89 110.13
Wind 60 deg - No Ice 6675.84 -7490.14 -141657.04 -171292.78 -41.82
Wind 90 deg - No Ice 7954.68 28.24 1095.52 -201436.27 3962.47
Wind 120 deg - No Ice 7510.95 4801.98 112355.59 -183813.65 4065.89
Wind 150 deg - No Ice 4504.54 8035.51 188795.83 -107141.80 2672.39
Wind 180 deg - No Ice 0.00 9576.47 220738.34 -194.53 -1294.50
Wind 210 deg - No Ice -4504.54 8035.51 188795.83 106752.74 -4914.53
Wind 240 deg - No Ice -7510.95 4801.98 112355.59 183424.60 -5360.39
Wind 270 deg - No Ice -7954.68 28.24 1095.52 201047.22 -3962.47
Wind 300 deg - No Ice -6675.84 -7490.14 -141657.04 170903.73 1336.32
Wind 330 deg - No Ice -3487.80 -9918.37 -209876.89 94551.84 2132.00
Total Weight 3566.95 756.61 -194.53
Wind 0 deg - Service 0.00 -3032.03 -65013.10 -194.53 352.38
Wind 30 deg - Service 949.42 -2699.90 -56580.30 -25985.60 29.98
Wind 60 deg - Service 1817.24 -2038.90 -38010.06 -46769.48 -11.38
Wind 90 deg - Service 2165.36 7.69 848.86 -54974.89 1078.63
Wind 120 deg - Service 2044.57 1307.16 31135.16 -50177.80 1106.78
Wind 150 deg - Service 1226.19 2187.36 51943.08 -29306.83 727.46
Wind 180 deg - Service 0.00 2606.83 60638.21 -194.53 -352.38
Wind 210 deg - Service -1226.19 2187.36 51943.08 28917.77 -1337.79
Wind 240 deg - Service -2044.57 1307.16 31135.16 49788.75 -1459.16
Wind 270 deg - Service -2165.36 7.69 848.86 54585.84 -1078.63
Wind 300 deg - Service -1817.24 -2038.90 -38010.06 46380.42 363.76
Wind 330 deg - Service -949.42 -2699.90 -56580.30 25596.54 580.36

Load Combinations
Comb. Description
No.
1 Dead Only
2 1.2 Dead+1.0 Wind 0 deg - No Ice
3 0.9 Dead+1.0 Wind 0 deg - No Ice
4 1.2 Dead+1.0 Wind 30 deg - No Ice
5 0.9 Dead+1.0 Wind 30 deg - No Ice
6 1.2 Dead+1.0 Wind 60 deg - No Ice
7 0.9 Dead+1.0 Wind 60 deg - No Ice

Page 17
 Job Page
tnxTower Rainbow Tower 12 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Comb. Description
No.
8 1.2 Dead+1.0 Wind 90 deg - No Ice
9 0.9 Dead+1.0 Wind 90 deg - No Ice
10 1.2 Dead+1.0 Wind 120 deg - No Ice
11 0.9 Dead+1.0 Wind 120 deg - No Ice
12 1.2 Dead+1.0 Wind 150 deg - No Ice
13 0.9 Dead+1.0 Wind 150 deg - No Ice
14 1.2 Dead+1.0 Wind 180 deg - No Ice
15 0.9 Dead+1.0 Wind 180 deg - No Ice
16 1.2 Dead+1.0 Wind 210 deg - No Ice
17 0.9 Dead+1.0 Wind 210 deg - No Ice
18 1.2 Dead+1.0 Wind 240 deg - No Ice
19 0.9 Dead+1.0 Wind 240 deg - No Ice
20 1.2 Dead+1.0 Wind 270 deg - No Ice
21 0.9 Dead+1.0 Wind 270 deg - No Ice
22 1.2 Dead+1.0 Wind 300 deg - No Ice
23 0.9 Dead+1.0 Wind 300 deg - No Ice
24 1.2 Dead+1.0 Wind 330 deg - No Ice
25 0.9 Dead+1.0 Wind 330 deg - No Ice
26 Dead+Wind 0 deg - Service
27 Dead+Wind 30 deg - Service
28 Dead+Wind 60 deg - Service
29 Dead+Wind 90 deg - Service
30 Dead+Wind 120 deg - Service
31 Dead+Wind 150 deg - Service
32 Dead+Wind 180 deg - Service
33 Dead+Wind 210 deg - Service
34 Dead+Wind 240 deg - Service
35 Dead+Wind 270 deg - Service
36 Dead+Wind 300 deg - Service
37 Dead+Wind 330 deg - Service

Maximum Member Forces

Section Elevation Component Condition Gov. Axial Major Axis Minor Axis
No. ft Type Load Moment Moment
Comb. lb lb-ft lb-ft
T1 40 - 20 Leg Max Tension 15 21609.56 4.05 5.90
Max. Compression 18 -22847.45 72.90 -39.03
Max. Mx 8 10158.56 118.37 -14.24
Max. My 24 -208.22 42.75 -120.64
Max. Vy 20 556.19 -0.00 -0.00
Max. Vx 2 530.03 -0.00 -0.00
Diagonal Max Tension 9 2063.94 8.40 1.71
Max. Compression 20 -2111.72 0.00 0.00
Max. Mx 18 1692.79 11.69 -1.62
Max. My 24 -1975.05 -7.18 4.02
Max. Vy 18 -5.78 11.69 -1.62
Max. Vx 24 1.61 0.00 0.00
Top Girt Max Tension 10 214.11 0.00 0.00
Max. Compression 15 -225.60 0.00 0.00
Max. Mx 10 214.11 -1.65 0.00
Max. My 16 23.42 0.00 0.00
Max. Vy 14 2.20 0.00 0.00
Max. Vx 16 -0.00 0.00 0.00
T2 20 - 0 Leg Max Tension 15 75842.84 2.64 -140.94
Max. Compression 2 -84423.06 0.00 0.00
Max. Mx 22 -16136.70 -438.56 67.32
Max. My 12 -27391.85 -0.41 436.88
Max. Vy 10 -869.81 -42.19 -6.45

Page 18
 Job Page
tnxTower Rainbow Tower 13 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Section Elevation Component Condition Gov. Axial Major Axis Minor Axis
No. ft Type Load Moment Moment
Comb. lb lb-ft lb-ft
Max. Vx 4 1395.60 -80.37 -32.91
Diagonal Max Tension 24 6217.03 36.08 -12.06
Max. Compression 24 -6706.69 0.00 0.00
Max. Mx 2 5088.39 63.90 7.75
Max. My 16 -3582.02 -40.27 31.23
Max. Vy 2 -28.44 63.90 7.75
Max. Vx 16 -12.50 -40.27 31.23
Top Girt Max Tension 20 190.02 0.00 0.00
Max. Compression 19 -191.05 0.00 0.00
Max. Mx 10 -188.41 -1.65 0.00
Max. My 16 13.31 0.00 0.00
Max. Vy 14 2.20 0.00 0.00
Max. Vx 16 -0.00 0.00 0.00

Maximum Reactions
Location Condition Gov. Vertical Horizontal, X Horizontal, Z
Load lb lb lb
Comb.
Leg C Max. Vert 18 84286.17 4818.43 -1658.18
Max. Hx 18 84286.17 4818.43 -1658.18
Max. Hz 7 -83354.60 -4445.88 3006.65
Min. Vert 7 -83354.60 -4445.88 3006.65
Min. H x 7 -83354.60 -4445.88 3006.65
Min. H z 14 43900.38 2021.62 -1886.47
Leg B Max. Vert 10 84441.72 -4695.92 -1871.93
Max. Hx 23 -83237.70 4319.62 3224.97
Max. Hz 25 -70910.64 3301.94 3256.41
Min. Vert 23 -83237.70 4319.62 3224.97
Min. H x 10 84441.72 -4695.92 -1871.93
Min. H z 14 44050.71 -1769.50 -2313.13
Leg A Max. Vert 2 94158.03 246.01 6215.27
Max. Hx 22 55935.38 937.13 4165.71
Max. Hz 2 94158.03 246.01 6215.27
Min. Vert 15 -83920.37 -252.22 -5384.34
Min. H x 7 55657.10 -689.15 4160.62
Min. H z 15 -83920.37 -252.22 -5384.34

Tower Mast Reaction Summary

Load Vertical Shearx Shearz Overturning Overturning Torque
Combination Moment, Mx Moment, Mz
lb lb lb lb-ft lb-ft lb-ft
Dead Only 3566.95 0.00 0.00 756.61 -194.53 0.00
1.2 Dead+1.0 Wind 0 deg - No 4280.34 0.00 -11138.47 -240922.85 -226.26 1295.05
Ice SRSS = 241096 lb-ft Max Reactions for
0.9 Dead+1.0 Wind 0 deg - No 3210.25 0.00 -11138.50 -241095.63 -167.74 1294.90 Foundation
Ice Design (CASE 1:
1.2 Dead+1.0 Wind 30 deg - No 4280.34 3487.70 -9918.33 -209914.07 -95069.01 115.30 Uniaxial Analysis)
Ice
0.9 Dead+1.0 Wind 30 deg - No 3210.25 3487.71 -9918.35 -210094.29 -94987.28 114.93
Ice
1.2 Dead+1.0 Wind 60 deg - No 4280.34 6675.71 -7490.06 -141624.15 -171493.19 -34.41
Max Reactions for
Tower Wt. for Foundation
Foundation Design (CASE 2:
Page 19
Design Biaxial Analysis)
 Job Page
tnxTower Rainbow Tower 14 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Load Vertical Shearx Shearz Overturning Overturning Torque

Combination Moment, Mx Moment, Mz
lb lb lb lb-ft lb-ft lb-ft
Ice
0.9 Dead+1.0 Wind 60 deg - No 3210.25 6675.73 -7490.07 -141821.23 -171393.53 -34.92
Ice
1.2 Dead+1.0 Wind 90 deg - No 4280.34 7954.59 28.32 1231.23 -201668.11 3964.00
Ice
0.9 Dead+1.0 Wind 90 deg - No 3210.25 7954.61 28.32 1003.97 -201561.13 3963.48
Ice
1.2 Dead+1.0 Wind 120 deg - 4280.34 7510.92 4801.98 112595.62 -184037.70 4066.74
No Ice
0.9 Dead+1.0 Wind 120 deg - 3210.25 7510.94 4801.99 112342.49 -183935.47 4066.34
No Ice
1.2 Dead+1.0 Wind 150 deg - 4280.34 4504.54 8035.41 189114.62 -107292.90 2673.20
No Ice
0.9 Dead+1.0 Wind 150 deg - 3210.25 4504.55 8035.43 188843.59 -107209.22 2673.04
No Ice
1.2 Dead+1.0 Wind 180 deg - 4280.34 0.00 9576.32 221089.87 -225.50 -1295.01
No Ice
0.9 Dead+1.0 Wind 180 deg - 3210.25 0.00 9576.34 220811.69 -167.14 -1294.87
No Ice
1.2 Dead+1.0 Wind 210 deg - 4280.34 -4504.54 8035.41 189108.30 106837.91 -4916.21
No Ice
0.9 Dead+1.0 Wind 210 deg - 3210.25 -4504.55 8035.43 188837.15 106870.96 -4915.81
No Ice
1.2 Dead+1.0 Wind 240 deg - 4280.34 -7510.92 4801.98 112589.43 183574.64 -5361.76
No Ice
0.9 Dead+1.0 Wind 240 deg - 3210.25 -7510.94 4801.99 112336.15 183589.21 -5361.21
No Ice
1.2 Dead+1.0 Wind 270 deg - 4280.34 -7954.59 28.31 1231.70 201200.86 -3964.00
No Ice
0.9 Dead+1.0 Wind 270 deg - 3210.25 -7954.61 28.32 1004.31 201210.77 -3963.48
No Ice
1.2 Dead+1.0 Wind 300 deg - 4280.34 -6675.71 -7490.07 -141617.50 171029.39 1329.53
No Ice
0.9 Dead+1.0 Wind 300 deg - 3210.25 -6675.73 -7490.08 -141814.54 171046.69 1329.88
No Ice
1.2 Dead+1.0 Wind 330 deg - 4280.34 -3487.69 -9918.33 -209907.40 94612.75 2127.80
No Ice
0.9 Dead+1.0 Wind 330 deg - 3210.25 -3487.70 -9918.35 -210087.58 94648.05 2127.91
No Ice
Dead+Wind 0 deg - Service 3566.95 0.00 -3032.01 -65062.21 -194.17 352.51
Dead+Wind 30 deg - Service 3566.95 949.41 -2699.88 -56622.60 -26006.57 30.70
Dead+Wind 60 deg - Service 3566.95 1817.22 -2038.89 -38036.84 -46806.78 -10.67
Dead+Wind 90 deg - Service 3566.95 2165.34 7.69 848.11 -55018.78 1079.07
Dead+Wind 120 deg - Service 3566.95 2044.55 1307.15 31158.03 -50218.40 1107.27
Dead+Wind 150 deg - Service 3566.95 1226.18 2187.34 51982.71 -29330.72 727.61
Dead+Wind 180 deg - Service 3566.95 0.00 2606.80 60684.68 -194.01 -352.55
Dead+Wind 210 deg - Service 3566.95 -1226.18 2187.34 51982.32 28942.39 -1338.15
Dead+Wind 240 deg - Service 3566.95 -2044.55 1307.15 31157.66 49829.44 -1459.75
Dead+Wind 270 deg - Service 3566.95 -2165.34 7.69 848.21 54629.45 -1079.07
Dead+Wind 300 deg - Service 3566.95 -1817.22 -2038.89 -38036.38 46417.66 363.21
Dead+Wind 330 deg - Service 3566.95 -949.40 -2699.88 -56621.97 25618.08 579.85

Solution Summary
Sum of Applied Forces Sum of Reactions
Load PX PY PZ PX PY PZ % Error
Comb. lb lb lb lb lb lb
1 0.00 -3566.95 0.00 -0.00 3566.95 -0.00 0.000%

Page 20
 Job Page
tnxTower Rainbow Tower 15 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Sum of Applied Forces Sum of Reactions

Load PX PY PZ PX PY PZ % Error
Comb. lb lb lb lb lb lb
2 0.00 -4280.34 -11138.50 -0.00 4280.34 11138.47 0.000%
3 0.00 -3210.25 -11138.50 -0.00 3210.25 11138.50 0.000%
4 3487.80 -4280.34 -9918.37 -3487.70 4280.34 9918.33 0.001%
5 3487.80 -3210.25 -9918.37 -3487.71 3210.25 9918.35 0.001%
6 6675.84 -4280.34 -7490.14 -6675.71 4280.34 7490.06 0.001%
7 6675.84 -3210.25 -7490.14 -6675.73 3210.25 7490.07 0.001%
8 7954.68 -4280.34 28.24 -7954.59 4280.34 -28.32 0.001%
9 7954.68 -3210.25 28.24 -7954.61 3210.25 -28.32 0.001%
10 7510.95 -4280.34 4801.98 -7510.92 4280.34 -4801.98 0.000%
11 7510.95 -3210.25 4801.98 -7510.94 3210.25 -4801.99 0.000%
12 4504.54 -4280.34 8035.51 -4504.54 4280.34 -8035.41 0.001%
13 4504.54 -3210.25 8035.51 -4504.55 3210.25 -8035.43 0.001%
14 -0.00 -4280.34 9576.47 -0.00 4280.34 -9576.32 0.001%
15 -0.00 -3210.25 9576.47 -0.00 3210.25 -9576.34 0.001%
16 -4504.54 -4280.34 8035.51 4504.54 4280.34 -8035.41 0.001%
17 -4504.54 -3210.25 8035.51 4504.55 3210.25 -8035.43 0.001%
18 -7510.95 -4280.34 4801.98 7510.92 4280.34 -4801.98 0.000%
19 -7510.95 -3210.25 4801.98 7510.94 3210.25 -4801.99 0.000%
20 -7954.68 -4280.34 28.24 7954.59 4280.34 -28.31 0.001%
21 -7954.68 -3210.25 28.24 7954.61 3210.25 -28.32 0.001%
22 -6675.84 -4280.34 -7490.14 6675.71 4280.34 7490.07 0.001%
23 -6675.84 -3210.25 -7490.14 6675.73 3210.25 7490.08 0.001%
24 -3487.80 -4280.34 -9918.37 3487.69 4280.34 9918.33 0.001%
25 -3487.80 -3210.25 -9918.37 3487.70 3210.25 9918.35 0.001%
26 0.00 -3566.95 -3032.03 -0.00 3566.95 3032.01 0.000%
27 949.42 -3566.95 -2699.90 -949.41 3566.95 2699.88 0.000%
28 1817.24 -3566.95 -2038.90 -1817.22 3566.95 2038.89 0.001%
29 2165.36 -3566.95 7.69 -2165.34 3566.95 -7.69 0.000%
30 2044.57 -3566.95 1307.16 -2044.55 3566.95 -1307.15 0.000%
31 1226.19 -3566.95 2187.36 -1226.18 3566.95 -2187.34 0.000%
32 -0.00 -3566.95 2606.83 -0.00 3566.95 -2606.80 0.001%
33 -1226.19 -3566.95 2187.36 1226.18 3566.95 -2187.34 0.000%
34 -2044.57 -3566.95 1307.16 2044.55 3566.95 -1307.15 0.000%
35 -2165.36 -3566.95 7.69 2165.34 3566.95 -7.69 0.000%
36 -1817.24 -3566.95 -2038.90 1817.22 3566.95 2038.89 0.001%
37 -949.42 -3566.95 -2699.90 949.40 3566.95 2699.88 0.000%

Non-Linear Convergence Results

Load Converged? Number Displacement Force
Combination of Cycles Tolerance Tolerance
1 Yes 6 0.00000001 0.00000001
2 Yes 6 0.00000001 0.00001504
3 Yes 6 0.00000001 0.00000001
4 Yes 6 0.00000001 0.00007920
5 Yes 6 0.00000001 0.00006695
6 Yes 6 0.00000001 0.00011749
7 Yes 6 0.00000001 0.00010053
8 Yes 6 0.00000001 0.00009043
9 Yes 6 0.00000001 0.00007818
10 Yes 6 0.00000001 0.00001870
11 Yes 6 0.00000001 0.00000674
12 Yes 6 0.00000001 0.00008302
13 Yes 6 0.00000001 0.00006928
14 Yes 6 0.00000001 0.00011973
15 Yes 6 0.00000001 0.00010256

Page 21
 Job Page
tnxTower Rainbow Tower 16 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

16 Yes 6 0.00000001 0.00008028

17 Yes 6 0.00000001 0.00006582
18 Yes 6 0.00000001 0.00002016
19 Yes 6 0.00000001 0.00000991
20 Yes 6 0.00000001 0.00009034
21 Yes 6 0.00000001 0.00007809
22 Yes 6 0.00000001 0.00011694
23 Yes 6 0.00000001 0.00010008
24 Yes 6 0.00000001 0.00008163
25 Yes 6 0.00000001 0.00007016
26 Yes 6 0.00000001 0.00004170
27 Yes 6 0.00000001 0.00005600
28 Yes 6 0.00000001 0.00006940
29 Yes 6 0.00000001 0.00005865
30 Yes 6 0.00000001 0.00004270
31 Yes 6 0.00000001 0.00005805
32 Yes 6 0.00000001 0.00007033
33 Yes 6 0.00000001 0.00005803
34 Yes 6 0.00000001 0.00004293
35 Yes 6 0.00000001 0.00005871
36 Yes 6 0.00000001 0.00006918
37 Yes 6 0.00000001 0.00005592

Maximum Tower Deflections - Service Wind

Section Elevation Horz. Gov. Tilt Twist
No. Deflection Load
ft in Comb. ° °
T1 40 - 20 0.525 26 0.0963 0.0277
T2 20 - 0 0.165 26 0.0565 0.0295

Critical Deflections and Radius of Curvature - Service Wind

Elevation Appurtenance Gov. Deflection Tilt Twist Radius of
Load Curvature
ft Comb. in ° ° ft
40.00 Telewave 256'' Omni 26 0.525 0.0963 0.0277 64494
30.00 8' x 2'' Dipole 26 0.327 0.0780 0.0315 32247
20.00 Hustler 102'' Omni 26 0.165 0.0565 0.0295 17589
18.00 Telewave 244'' Omni 26 0.140 0.0516 0.0279 18281
12.00 Andrew 8' MW w/ Radome 26 0.080 0.0355 0.0207 26872
10.00 Trimble GPS 26 0.064 0.0298 0.0177 32247

Maximum Tower Deflections - Design Wind

Section Elevation Horz. Gov. Tilt Twist
No. Deflection Load
ft in Comb. ° °
T1 40 - 20 1.943 3 0.3553 0.1015
T2 20 - 0 0.611 3 0.2094 0.1083

Page 22
 Job Page
tnxTower Rainbow Tower 17 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Critical Deflections and Radius of Curvature - Design Wind

Elevation Appurtenance Gov. Deflection Tilt Twist Radius of
Load Curvature
ft Comb. in ° ° ft
40.00 Telewave 256'' Omni 3 1.943 0.3553 0.1015 17607
30.00 8' x 2'' Dipole 3 1.210 0.2883 0.1157 8804
20.00 Hustler 102'' Omni 3 0.611 0.2094 0.1083 4802
18.00 Telewave 244'' Omni 3 0.519 0.1912 0.1024 4991
12.00 Andrew 8' MW w/ Radome 3 0.297 0.1317 0.0760 7336
10.00 Trimble GPS 3 0.238 0.1107 0.0649 8803

Bolt Design Data

Section Elevation Component Bolt Bolt Size Number Maximum Allowable Ratio Allowable Criteria
No. Type Grade Of Load per Load Load Ratio
ft in Bolts Bolt lb Allowable
lb
T1 40 Leg A325N 0.6250 4 1411.55 20708.70 1 Bolt Tension
0.068
Diagonal A325N 0.6250 1 2063.94 3194.53 1 Member Block
0.646
Shear
T2 20 Leg A325N 0.6250 4 7558.96 20708.70 1 Bolt Tension
0.365
Diagonal A325N 0.6250 1 6217.03 9107.81 1 Member Block
0.683
Shear

Compression Checks

Leg Design Data (Compression)

Section Elevation Size L Lu Kl/r A Pu fPn Ratio
No. Pu
ft ft ft in2 lb lb fPn
T1 40 - 20 1 5/8 20.00 4.00 118.2 2.0739 -22847.40 32222.80 0.709 1
K=1.00
T2 20 - 0 2 3/4 20.00 4.00 69.8 5.9396 -84423.10 148885.00 0.567 1
K=1.00

1
Pu / fPn controls

Diagonal Design Data (Compression)

Page 23
 Job Page
tnxTower Rainbow Tower 18 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Section Elevation Size L Lu Kl/r A Pu fPn Ratio

No. Pu
ft ft ft in2 lb lb fPn
T1 40 - 20 L1 1/2x1 1/2x1/8 5.00 2.39 96.7 0.3594 -2111.72 7115.97 0.297 1
K=1.00
T2 20 - 0 L2x2x1/4 5.00 2.31 70.9 0.9380 -6706.69 23330.90 0.287 1
K=1.00

1
Pu / fPn controls

Top Girt Design Data (Compression)

Section Elevation Size L Lu Kl/r A Pu fPn Ratio
No. Pu
2
ft ft ft in lb lb fPn
T1 40 - 20 L1 1/2x1 1/2x1/8 3.00 2.86 116.1 0.3594 -225.60 5729.76 0.039 1
K=1.00
T2 20 - 0 L1 1/2x1 1/2x1/8 3.00 2.86 116.1 0.3594 -191.05 5729.76 0.033 1
K=1.00

1
Pu / fPn controls

Tension Checks

Leg Design Data (Tension)

Section Elevation Size L Lu Kl/r A Pu fPn Ratio
No. Pu
ft ft ft in2 lb lb fPn
T1 40 - 20 1 5/8 20.00 4.00 118.2 2.0739 21609.60 67195.70 0.322 1

T2 20 - 0 2 3/4 20.00 4.00 69.8 5.9396 75842.80 192442.00 0.394 1

1
Pu / fPn controls

Diagonal Design Data (Tension)

Section Elevation Size L Lu Kl/r A Pu fPn Ratio
No. Pu
2
ft ft ft in lb lb fPn
T1 40 - 20 L1 1/2x1 1/2x1/8 5.00 2.39 61.6 0.1992 2063.94 8666.02 0.238 1

T2 20 - 0 L2x2x1/4 5.00 2.31 45.5 0.5629 6217.03 24485.10 0.254 1

Page 24
 Job Page
tnxTower Rainbow Tower 19 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Section Elevation Size L Lu Kl/r A Pu fPn Ratio

No. Pu
ft ft ft in2 lb lb fPn

1
Pu / fPn controls

Top Girt Design Data (Tension)

Section Elevation Size L Lu Kl/r A Pu fPn Ratio
No. Pu
ft ft ft in2 lb lb fPn
T1 40 - 20 L1 1/2x1 1/2x1/8 3.00 2.86 73.9 0.3594 214.11 11643.80 0.018 1

T2 20 - 0 L1 1/2x1 1/2x1/8 3.00 2.86 73.9 0.3594 190.02 11643.80 0.016 1

1
Pu / fPn controls

Section Capacity Table

Section Elevation Component Size Critical P øPallow % Pass
No. ft Type Element lb lb Capacity Fail
T1 40 - 20 Leg 1 5/8 1 -22847.40 32222.80 70.9 Pass
T2 20 - 0 Leg 2 3/4 39 -84423.10 148885.00 56.7 Pass
T1 40 - 20 Diagonal L1 1/2x1 1/2x1/8 7 -2111.72 7115.97 29.7 Pass
64.6 (b)
T2 20 - 0 Diagonal L2x2x1/4 46 -6706.69 23330.90 28.7 Pass
68.3 (b)
T1 40 - 20 Top Girt L1 1/2x1 1/2x1/8 4 -225.60 5729.76 3.9 Pass
T2 20 - 0 Top Girt L1 1/2x1 1/2x1/8 41 -191.05 5729.76 3.3 Pass
Summary
Leg (T1) 70.9 Pass
Diagonal 68.3 Pass
(T2)
Top Girt 3.9 Pass
(T1)
Bolt Checks 68.3 Pass
RATING = 70.9 Pass

Element Map
Section Section Component Element List
No. Elevation Type
ft
T1 40.00-20.00 Leg 1-3
Diagonal 7-36
Top Girt 4-6
T2 20.00-0.00 Leg 37-39
Diagonal 43-72

Page 25
 Job Page
tnxTower Rainbow Tower 20 of 20
Project Date
AECOM
4225 Executive Square, Ste. 1400 09:03:47 07/24/17
La Jolla, CA 92037 Client Designed by
Phone: (858) 812-9292 County of San Diego
FAX: - David Hollinger

Section Section Component Element List

No. Elevation Type
ft
Top Girt 40-42
Total number of elements: 72

Program Version 7.0.7.0 - 7/18/2016 File:U:/Projects/_Jobs/60543652 Radio Tower/400-Technical/419 Structural/TnxTower Analysis/Rainbow Tower v.1.eri

Page 26
Page 27
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 1 (Uniaxial Analysis)

Code References
ACI 318-11,
Calculations per ACI 318-14, IBC
IBC 2012,
2015, CBC
CBC 2013,
2016, ASCE 7-10 1.5 ksf * 1/3 increase for short term
Load Combinations Used : ASCE 7-10 loading (per soils report) = 2 ksf
General Information
Material Properties Soil Design Values
f'c : Concrete 28 day strength = 4.0 ksi Allowable Soil Bearing = 2.0 ksf
fy : Rebar Yield = 60.0 ksi Increase Bearing By Footing Weight = No
Ec : Concrete Elastic Modulus = 3,122.0 ksi Soil Passive Resistance (for Sliding) = 10.0 pcf
Concrete Density = 145.0 pcf Soil/Concrete Friction Coeff. = 0.350
Values Flexure = 0.90
Shear = 0.750 Increases based on footing Depth
Analysis Settings Footing base depth below soil surface = 3.0 ft
Min Steel % Bending Reinf. = Allowable pressure increase per foot of depth= ksf
Min Allow % Temp Reinf. = 0.00090 when footing base is below = ft
Min. Overturning Safety Factor = 1.0 : 1
Min. Sliding Safety Factor = 1.0 : 1 Increases based on footing plan dimension
Add Ftg Wt for Soil Pressure : Yes Allowable pressure increase per foot of depth= ksf
Use ftg wt for stability, moments & shears : Yes when maximum length or width is greater =than ft
Add Pedestal Wt for Soil Pressure : No
Per soils report, no passive resistance
Use Pedestal wt for stability, mom & shear : No
is permitted for tower foundation. 10 pcf
Dimensions is lowest input Enercalc program allows
Width parallel to X-X Axis = 12.0 ft for passiveZ resistance and is negligible.
Length parallel to Z-Z Axis = 12.0 ft
Footing Thickness = 36.0 in
12'-0"

X X
Pedestal dimensions...
px : parallel to X-X Axis = in
pz : parallel to Z-Z Axis = in
Height = in Edge Dist. = 3"
Rebar Centerline to Edge of Concrete...
at Bottom of footing = 3.0 in

Reinforcing 12'-0"
Z
Bars parallel to X-X Axis
Number of Bars = 12.0
Reinforcing Bar Size = # 6
Bars parallel to Z-Z Axis
Number of Bars = 12.0
Reinforcing Bar Size = # 6
12 - # 6 Bars 12 - # 6 Bars
3"

3"

Bandwidth Distribution Check (ACI 15.4.4.2) X-X Section Looking to +Z Z-Z Section Looking to +X

Direction Requiring Closer Separation n/a

# Bars required within zone n/a
# Bars required on each side of zone n/a
Applied Loads
D Lr L S W E H
P : Column Load = 3.570 k
OB : Overburden = ksf
M-xx = 241.40 k-ft
M-zz = k-ft
V-x = k
V-z = 11.140 k

Page 28
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 1 (Uniaxial Analysis)

DESIGN SUMMARY Design OK

Min. Ratio Item Applied Capacity Governing Load Combination
PASS 0.5860 Soil Bearing 1.172 ksf 2.0 ksf +0.60D+0.60W+0.60H about X-X axis
PASS 1.446 Overturning - X-X 164.892 k-ft 238.356 k-ft +0.60D+0.60W+0.60H
PASS n/a Overturning - Z-Z 0.0 k-ft 0.0 k-ft No Overturning
PASS n/a Sliding - X-X 0.0 k 0.0 k No Sliding
PASS 2.161 Sliding - Z-Z 6.684 k 14.444 k +0.60D+0.60W+0.60H
PASS n/a Uplift 0.0 k 0.0 k No Uplift
PASS 0.009713 Z Flexure (+X) 0.6284 k-ft 64.699 k-ft +1.408D+0.50L+0.20S+E+1.60H
PASS 0.009713 Z Flexure (-X) 0.6284 k-ft 64.699 k-ft +1.408D+0.50L+0.20S+E+1.60H
PASS 0.2449 X Flexure (+Z) 15.846 k-ft 64.699 k-ft +0.90D+W+0.90H
PASS 0.1427 X Flexure (-Z) 9.232 k-ft 64.699 k-ft +1.20D+0.50L+0.50S+W+1.60H
PASS 0.002974 1-way Shear (+X) 0.2821 psi 94.868 psi +1.408D+0.50L+0.20S+E+1.60H
PASS 0.002974 1-way Shear (-X) 0.2821 psi 94.868 psi +1.408D+0.50L+0.20S+E+1.60H
PASS 0.09175 1-way Shear (+Z) 8.704 psi 94.868 psi +0.90D+W+0.90H
PASS 0.04446 1-way Shear (-Z) 4.218 psi 94.868 psi +1.20D+0.50Lr+0.50L+W+1.60H
PASS 0.007596 2-way Punching 1.441 psi 189.737 psi +0.90D+W+0.90H
Detailed Results
Soil Bearing
Rotation Axis & Actual Soil Bearing Stress Actual / Allowable
Load Combination... Gross Allowable Xecc Zecc Bottom, -Z Top, +Z Left, -X Right, +X Ratio
X-X, +D+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+L+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+Lr+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+S+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+0.750Lr+0.750L+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+0.750L+0.750S+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+0.60W+H 2.0 n/a 29.885 0.0 1.038 n/a n/a 0.519
X-X, +D+0.70E+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +D+0.750Lr+0.750L+0.450W+H 2.0 n/a 22.414 0.03754 0.8820 n/a n/a 0.441
X-X, +D+0.750L+0.750S+0.450W+H 2.0 n/a 22.414 0.03754 0.8820 n/a n/a 0.441
X-X, +D+0.750L+0.750S+0.5250E+H 2.0 n/a 0.0 0.4598 0.4598 n/a n/a 0.230
X-X, +0.60D+0.60W+0.60H 2.0 n/a 49.809 0.0 1.172 n/a n/a 0.586
X-X, +0.60D+0.70E+0.60H 2.0 n/a 0.0 0.2759 0.2759 n/a n/a 0.138
Z-Z, +D+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+L+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+Lr+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+S+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.750Lr+0.750L+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.750L+0.750S+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.60W+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.70E+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.750Lr+0.750L+0.450W+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.750L+0.750S+0.450W+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +D+0.750L+0.750S+0.5250E+H 2.0 0.0 n/a n/a n/a 0.4598 0.4598 0.230
Z-Z, +0.60D+0.60W+0.60H 2.0 0.0 n/a n/a n/a 0.2759 0.2759 0.138
Z-Z, +0.60D+0.70E+0.60H 2.0 0.0 n/a n/a n/a 0.2759 0.2759 0.138
Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+H None 0.0 k-ft Infinity OK
X-X, +D+L+H None 0.0 k-ft Infinity OK
X-X, +D+Lr+H None 0.0 k-ft Infinity OK
X-X, +D+S+H None 0.0 k-ft Infinity OK
X-X, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
X-X, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
X-X, +D+0.60W+H 164.892 k-ft 397.260 k-ft 2.409 OK
X-X, +D+0.70E+H None 0.0 k-ft Infinity OK
X-X, +D+0.750Lr+0.750L+0.450W+H 123.669 k-ft 397.260 k-ft 3.212 OK
X-X, +D+0.750L+0.750S+0.450W+H 123.669 k-ft 397.260 k-ft 3.212 OK

Page 29
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 1 (Uniaxial Analysis)

Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+0.750L+0.750S+0.5250E+H None 0.0 k-ft Infinity OK
X-X, +0.60D+0.60W+0.60H 164.892 k-ft 238.356 k-ft 1.446 OK
X-X, +0.60D+0.70E+0.60H None 0.0 k-ft Infinity OK
Z-Z, +D+H None 0.0 k-ft Infinity OK
Z-Z, +D+L+H None 0.0 k-ft Infinity OK
Z-Z, +D+Lr+H None 0.0 k-ft Infinity OK
Z-Z, +D+S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.60W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.70E+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+0.450W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+0.5250E+H None 0.0 k-ft Infinity OK
Z-Z, +0.60D+0.60W+0.60H None 0.0 k-ft Infinity OK
Z-Z, +0.60D+0.70E+0.60H None 0.0 k-ft Infinity OK
Sliding Stability All units k
Force Application Axis
Load Combination... Sliding Force Resisting Force Sliding SafetyRatio Status
X-X, +D+H 0.0 k 23.714 k No Sliding OK
X-X, +D+L+H 0.0 k 23.714 k No Sliding OK
X-X, +D+Lr+H 0.0 k 23.714 k No Sliding OK
X-X, +D+S+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750Lr+0.750L+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750L+0.750S+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.60W+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.70E+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750Lr+0.750L+0.450W+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750L+0.750S+0.450W+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750L+0.750S+0.5250E+H 0.0 k 23.714 k No Sliding OK
X-X, +0.60D+0.60W+0.60H 0.0 k 14.444 k No Sliding OK
X-X, +0.60D+0.70E+0.60H 0.0 k 14.444 k No Sliding OK
Z-Z, +D+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+L+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+Lr+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+S+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750Lr+0.750L+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750L+0.750S+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750L+0.750S+0.450W+H 5.013 k 23.714 k 4.730 OK
Z-Z, +D+0.750L+0.750S+0.5250E+H 0.0 k 23.714 k No Sliding OK
Z-Z, +0.60D+0.60W+0.60H 6.684 k 14.444 k 2.161 OK
Z-Z, +0.60D+0.70E+0.60H 0.0 k 14.444 k No Sliding OK
Z-Z, +D+0.60W+H 6.684 k 23.714 k 3.548 OK
Z-Z, +D+0.70E+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H 5.013 k 23.714 k 4.730 OK
Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.40D+1.60H 0.6248 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.40D+1.60H 0.6248 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 0.5355 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 0.5355 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60L+0.50S+1.60H 0.5355 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60L+0.50S+1.60H 0.5355 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 0.5355 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 0.5355 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 6.259 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 5.188 -Z Top 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+1.60S+1.60H 0.5355 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+1.60S+1.60H 0.5355 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60S+0.50W+1.60H 6.259 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK

Page 30
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 1 (Uniaxial Analysis)

Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.20D+1.60S+0.50W+1.60H 5.188 -Z Top 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 13.664 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 9.232 -Z Top 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 13.664 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 9.232 -Z Top 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.408D+0.50L+0.20S+E+1.60H 0.6284 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.408D+0.50L+0.20S+E+1.60H 0.6284 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+W+0.90H 15.846 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+W+0.90H 7.047 -Z Top 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.6918D+E+0.90H 0.3087 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.6918D+E+0.90H 0.3087 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.40D+1.60H 0.6248 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.40D+1.60H 0.6248 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 0.5355 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 0.5355 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.408D+0.50L+0.20S+E+1.60H 0.6284 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.408D+0.50L+0.20S+E+1.60H 0.6284 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+W+0.90H 0.4016 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+W+0.90H 0.4016 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.6918D+E+0.90H 0.3087 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.6918D+E+0.90H 0.3087 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
One Way Shear
Load Combination... Vu @ -X Vu @ +X Vu @ -Z Vu @ +Z Vu:Max Phi Vn Vu / Phi*Vn Status
+1.40D+1.60H 0.2805 psi 0.2805 psi 0.2805 psi 0.2805 psi 0.2805 psi 94.868 psi 0.002956 OK
+1.20D+0.50Lr+1.60L+1.60H 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 94.868 psi 0.002534 OK
+1.20D+1.60L+0.50S+1.60H 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 94.868 psi 0.002534 OK
+1.20D+1.60Lr+0.50L+1.60H 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 94.868 psi 0.002534 OK
+1.20D+1.60Lr+0.50W+1.60H 0.2404 psi 0.2404 psi 2.587 psi 3.068 psi 3.068 psi 94.868 psi 0.03234 OK
+1.20D+0.50L+1.60S+1.60H 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 0.2404 psi 94.868 psi 0.002534 OK
+1.20D+1.60S+0.50W+1.60H 0.2404 psi 0.2404 psi 2.587 psi 3.068 psi 3.068 psi 94.868 psi 0.03234 OK
+1.20D+0.50Lr+0.50L+W+1.60H 0.2404 psi 0.2404 psi 4.218 psi 6.873 psi 6.873 psi 94.868 psi 0.07244 OK
+1.20D+0.50L+0.50S+W+1.60H 0.2404 psi 0.2404 psi 4.218 psi 6.873 psi 6.873 psi 94.868 psi 0.07244 OK
+1.408D+0.50L+0.20S+E+1.60H 0.2821 psi 0.2821 psi 0.2821 psi 0.2821 psi 0.2821 psi 94.868 psi 0.002974 OK
+0.90D+W+0.90H 0.1803 psi 0.1803 psi 3.164 psi 8.704 psi 8.704 psi 94.868 psi 0.09175 OK
+0.6918D+E+0.90H 0.1386 psi 0.1386 psi 0.1386 psi 0.1386 psi 0.1386 psi 94.868 psi 0.001461 OK
Punching Shear All units k
Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+1.40D+1.60H 1.085 psi 189.737 psi 0.005718 OK
+1.20D+0.50Lr+1.60L+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+1.60L+0.50S+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+1.60Lr+0.50L+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+1.60Lr+0.50W+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+0.50L+1.60S+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+1.60S+0.50W+1.60H 0.9299 psi 189.737 psi 0.004901 OK
+1.20D+0.50Lr+0.50L+W+1.60H 1.257 psi 189.737 psi 0.006626 OK
+1.20D+0.50L+0.50S+W+1.60H 1.257 psi 189.737 psi 0.006626 OK
+1.408D+0.50L+0.20S+E+1.60H 1.091 psi 189.737 psi 0.005751 OK

Page 31
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 1 (Uniaxial Analysis)

Punching Shear All units k

Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+0.90D+W+0.90H 1.441 psi 189.737 psi 0.007596 OK
+0.6918D+E+0.90H 0.5361 psi 189.737 psi 0.002826 OK

Page 32
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 2 (Biiaxial Analysis)

Code References
ACI 318-11,
Calculations per ACI 318-14, IBC
IBC 2012,
2015, CBC
CBC 2013,
2016, ASCE 7-10 1.5 ksf * 1/3 increase for short term
Load Combinations Used : ASCE 7-10 loading (per soils report) = 2 ksf
General Information
Material Properties Soil Design Values
f'c : Concrete 28 day strength = 4.0 ksi Allowable Soil Bearing = 2.0 ksf
fy : Rebar Yield = 60.0 ksi Increase Bearing By Footing Weight = No
Ec : Concrete Elastic Modulus = 3,122.0 ksi Soil Passive Resistance (for Sliding) = 10.0 pcf
Concrete Density = 145.0 pcf Soil/Concrete Friction Coeff. = 0.350
Values Flexure = 0.90
Shear = 0.750 Increases based on footing Depth
Analysis Settings Footing base depth below soil surface = 3.0 ft
Min Steel % Bending Reinf. = Allowable pressure increase per foot of depth= ksf
Min Allow % Temp Reinf. = 0.00090 when footing base is below = ft
Min. Overturning Safety Factor = 1.0 : 1
Min. Sliding Safety Factor = 1.0 : 1 Increases based on footing plan dimension
Add Ftg Wt for Soil Pressure : Yes Allowable pressure increase per foot of depth= ksf
Use ftg wt for stability, moments & shears : Yes when maximum length or width is greater =than ft
Add Pedestal Wt for Soil Pressure : No
Per soils report, no passive resistance
Use Pedestal wt for stability, mom & shear : No
is permitted for tower foundation. 10 pcf
Dimensions is lowest input Enercalc program allows
Width parallel to X-X Axis = 12.0 ft for passiveZ resistance and is negligible.
Length parallel to Z-Z Axis = 12.0 ft
Footing Thickness = 36.0 in
12'-0"

X X
Pedestal dimensions...
px : parallel to X-X Axis = in
pz : parallel to Z-Z Axis = in
Height = in Edge Dist. = 3"
Rebar Centerline to Edge of Concrete...
at Bottom of footing = 3.0 in

Reinforcing 12'-0"
Z
Bars parallel to X-X Axis
Number of Bars = 12.0
Reinforcing Bar Size = # 6
Bars parallel to Z-Z Axis
Number of Bars = 12.0
Reinforcing Bar Size = # 6
12 - # 6 Bars 12 - # 6 Bars
3"
3"

Bandwidth Distribution Check (ACI 15.4.4.2) X-X Section Looking to +Z Z-Z Section Looking to +X

Direction Requiring Closer Separation n/a

# Bars required within zone n/a
# Bars required on each side of zone n/a
Applied Loads
D Lr L S W E H
P : Column Load = 3.570 k
OB : Overburden = ksf
M-xx = 94.990 k-ft
M-zz = 210.10 k-ft
V-x = 3.490 k
V-z = 9.920 k

Page 33
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 2 (Biiaxial Analysis)

DESIGN SUMMARY Design OK

Min. Ratio Item Applied Capacity Governing Load Combination
PASS 0.6865 Soil Bearing 1.373 ksf 2.0 ksf 30.8 deg CCW
PASS 3.184 Overturning - X-X 74.850 k-ft 238.356 k-ft +0.60D+0.60W+0.60H
PASS 1.801 Overturning - Z-Z 132.342 k-ft 238.356 k-ft +0.60D+0.60W+0.60H
PASS 6.898 Sliding - X-X 2.094 k 14.444 k +0.60D+0.60W+0.60H
PASS 2.427 Sliding - Z-Z 5.952 k 14.444 k +0.60D+0.60W+0.60H
PASS n/a Uplift 0.0 k 0.0 k No Uplift
PASS 0.5174 Z Flexure (+X) 33.475 k-ft 64.699 k-ft +0.90D+W+0.90H
PASS 0.1910 Z Flexure (-X) 12.359 k-ft 64.699 k-ft +1.40D+1.60H
PASS 0.5327 X Flexure (+Z) 34.467 k-ft 64.699 k-ft +0.90D+W+0.90H
PASS 0.1910 X Flexure (-Z) 12.359 k-ft 64.699 k-ft +1.40D+1.60H
PASS 0.1691 1-way Shear (+X) 16.040 psi 94.868 psi +0.90D+W+0.90H
PASS 0.05849 1-way Shear (-X) 5.548 psi 94.868 psi +1.40D+1.60H
PASS 0.08756 1-way Shear (+Z) 8.307 psi 94.868 psi +0.90D+W+0.90H
PASS 0.06636 1-way Shear (-Z) 6.295 psi 94.868 psi +1.20D+0.50Lr+0.50L+W+1.60H
PASS 0.1060 2-way Punching 20.121 psi 189.737 psi +1.40D+1.60H
Detailed Results
Soil Bearing
Rotation Axis & Actual Soil Bearing Stress Actual / Allowable
Load Combination... Gross Allowable Xecc Zecc Bottom Left Top Left Top Right Bottom Right Ratio
, +D+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+L+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+Lr+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+S+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+0.750Lr+0.750L+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+0.750L+0.750S+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+0.60W+H 0.000
, 30.3 deg CCW 2.0 23.986 13.566 0.2422 0.0 0.6537 1.230 0.615
, +D+0.70E+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +D+0.750Lr+0.750L+0.450W+H 0.000
, 29.8 deg CCW 2.0 17.989 10.174 0.3096 0.0 0.6089 1.008 0.504
, +D+0.750L+0.750S+0.450W+H 0.000
, 29.8 deg CCW 2.0 17.989 10.174 0.3096 0.0 0.6089 1.008 0.504
, +D+0.750L+0.750S+0.5250E+H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.4598 0.4598 0.4598 0.4598 0.230
, +0.60D+0.60W+0.60H 0.000
, 30.8 deg CCW 2.0 39.976 22.610 0.0 0.0 0.4154 1.373 0.687
, +0.60D+0.70E+0.60H 0.000
, 0.0 deg CCW 2.0 0.0 0.0 0.2759 0.2759 0.2759 0.2759 0.138
Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+H None 0.0 k-ft Infinity OK
X-X, +D+L+H None 0.0 k-ft Infinity OK
X-X, +D+Lr+H None 0.0 k-ft Infinity OK
X-X, +D+S+H None 0.0 k-ft Infinity OK
X-X, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
X-X, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
X-X, +D+0.60W+H 74.850 k-ft 397.260 k-ft 5.307 OK
X-X, +D+0.70E+H None 0.0 k-ft Infinity OK
X-X, +D+0.750Lr+0.750L+0.450W+H 56.138 k-ft 397.260 k-ft 7.077 OK
X-X, +D+0.750L+0.750S+0.450W+H 56.138 k-ft 397.260 k-ft 7.077 OK

Page 34
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 2 (Biiaxial Analysis)

Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+0.750L+0.750S+0.5250E+H None 0.0 k-ft Infinity OK
X-X, +0.60D+0.60W+0.60H 74.850 k-ft 238.356 k-ft 3.184 OK
X-X, +0.60D+0.70E+0.60H None 0.0 k-ft Infinity OK
Z-Z, +D+H None 0.0 k-ft Infinity OK
Z-Z, +D+L+H None 0.0 k-ft Infinity OK
Z-Z, +D+Lr+H None 0.0 k-ft Infinity OK
Z-Z, +D+S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.60W+H 132.342 k-ft 397.260 k-ft 3.002 OK
Z-Z, +D+0.70E+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H 99.257 k-ft 397.260 k-ft 4.002 OK
Z-Z, +D+0.750L+0.750S+0.450W+H 99.257 k-ft 397.260 k-ft 4.002 OK
Z-Z, +D+0.750L+0.750S+0.5250E+H None 0.0 k-ft Infinity OK
Z-Z, +0.60D+0.60W+0.60H 132.342 k-ft 238.356 k-ft 1.801 OK
Z-Z, +0.60D+0.70E+0.60H None 0.0 k-ft Infinity OK
Sliding Stability All units k
Force Application Axis
Load Combination... Sliding Force Resisting Force Sliding SafetyRatio Status
X-X, +D+H 0.0 k 23.714 k No Sliding OK
X-X, +D+L+H 0.0 k 23.714 k No Sliding OK
X-X, +D+Lr+H 0.0 k 23.714 k No Sliding OK
X-X, +D+S+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750Lr+0.750L+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750L+0.750S+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.60W+H 2.094 k 23.714 k 11.325 OK
X-X, +D+0.70E+H 0.0 k 23.714 k No Sliding OK
X-X, +D+0.750Lr+0.750L+0.450W+H 1.571 k 23.714 k 15.099 OK
X-X, +D+0.750L+0.750S+0.450W+H 1.571 k 23.714 k 15.099 OK
X-X, +D+0.750L+0.750S+0.5250E+H 0.0 k 23.714 k No Sliding OK
X-X, +0.60D+0.60W+0.60H 2.094 k 14.444 k 6.898 OK
X-X, +0.60D+0.70E+0.60H 0.0 k 14.444 k No Sliding OK
Z-Z, +D+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+L+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+Lr+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+S+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750Lr+0.750L+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750L+0.750S+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750L+0.750S+0.450W+H 4.464 k 23.714 k 5.312 OK
Z-Z, +D+0.750L+0.750S+0.5250E+H 0.0 k 23.714 k No Sliding OK
Z-Z, +0.60D+0.60W+0.60H 5.952 k 14.444 k 2.427 OK
Z-Z, +0.60D+0.70E+0.60H 0.0 k 14.444 k No Sliding OK
Z-Z, +D+0.60W+H 5.952 k 23.714 k 3.984 OK
Z-Z, +D+0.70E+H 0.0 k 23.714 k No Sliding OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H 4.464 k 23.714 k 5.312 OK
Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.40D+1.60H 12.359 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.40D+1.60H 12.359 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 10.594 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 10.594 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60L+0.50S+1.60H 10.594 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60L+0.50S+1.60H 10.594 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 10.594 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 10.594 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 18.991 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 8.726 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+1.60S+1.60H 10.594 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+1.60S+1.60H 10.594 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+1.60S+0.50W+1.60H 18.991 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK

Page 35
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 2 (Biiaxial Analysis)

Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.20D+1.60S+0.50W+1.60H 8.726 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 31.016 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 4.358 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 31.016 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 4.358 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.20S+E+1.60H 10.594 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +1.20D+0.50L+0.20S+E+1.60H 10.594 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+W+0.90H 34.467 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+W+0.90H 0.4722 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+E+0.90H 7.945 +Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
X-X, +0.90D+E+0.90H 7.945 -Z Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.40D+1.60H 12.359 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.40D+1.60H 12.359 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 10.594 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 10.594 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 10.594 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 10.594 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 10.594 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 10.594 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 8.726 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 18.776 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 10.594 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 10.594 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 8.726 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 18.776 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 4.358 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 30.490 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 4.358 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 30.490 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.20S+E+1.60H 10.594 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +1.20D+0.50L+0.20S+E+1.60H 10.594 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+W+0.90H 0.4722 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+W+0.90H 33.475 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+E+0.90H 7.945 -X Bottom 0.3888 Min Temp % 0.440 64.699 OK
Z-Z, +0.90D+E+0.90H 7.945 +X Bottom 0.3888 Min Temp % 0.440 64.699 OK
One Way Shear
Load Combination... Vu @ -X Vu @ +X Vu @ -Z Vu @ +Z Vu:Max Phi Vn Vu / Phi*Vn Status
+1.40D+1.60H 5.548 psi 5.548 psi 5.548 psi 3.815 psi 5.548 psi 94.868 psi 0.05849 OK
+1.20D+0.50Lr+1.60L+1.60H 4.756 psi 4.756 psi 4.756 psi 3.27 psi 4.756 psi 94.868 psi 0.05013 OK
+1.20D+1.60L+0.50S+1.60H 4.756 psi 4.756 psi 4.756 psi 3.27 psi 4.756 psi 94.868 psi 0.05013 OK
+1.20D+1.60Lr+0.50L+1.60H 4.756 psi 4.756 psi 4.756 psi 3.27 psi 4.756 psi 94.868 psi 0.05013 OK
+1.20D+1.60Lr+0.50W+1.60H 3.691 psi 8.655 psi 5.818 psi 5.33 psi 8.655 psi 94.868 psi 0.09123 OK
+1.20D+0.50L+1.60S+1.60H 4.756 psi 4.756 psi 4.756 psi 3.27 psi 4.756 psi 94.868 psi 0.05013 OK
+1.20D+1.60S+0.50W+1.60H 3.691 psi 8.655 psi 5.818 psi 5.33 psi 8.655 psi 94.868 psi 0.09123 OK
+1.20D+0.50Lr+0.50L+W+1.60H 1.36 psi 14.288 psi 6.295 psi 8.075 psi 14.288 psi 94.868 psi 0.1506 OK
+1.20D+0.50L+0.50S+W+1.60H 1.36 psi 14.288 psi 6.295 psi 8.075 psi 14.288 psi 94.868 psi 0.1506 OK
+1.20D+0.50L+0.20S+E+1.60H 4.756 psi 4.756 psi 4.756 psi 3.27 psi 4.756 psi 94.868 psi 0.05013 OK
+0.90D+W+0.90H 0 psi 16.04 psi 3.692 psi 8.307 psi 16.04 psi 94.868 psi 0.1691 OK
+0.90D+E+0.90H 3.567 psi 3.567 psi 3.567 psi 2.452 psi 3.567 psi 94.868 psi 0.0376 OK
Punching Shear All units k
Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+1.40D+1.60H 20.121 psi 189.737 psi 0.106 OK
+1.20D+0.50Lr+1.60L+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+1.60L+0.50S+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+1.60Lr+0.50L+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+1.60Lr+0.50W+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+0.50L+1.60S+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+1.60S+0.50W+1.60H 17.247 psi 189.737 psi 0.0909 OK
+1.20D+0.50Lr+0.50L+W+1.60H 17.466 psi 189.737 psi 0.09205 OK
+1.20D+0.50L+0.50S+W+1.60H 17.466 psi 189.737 psi 0.09205 OK
+1.20D+0.50L+0.20S+E+1.60H 17.247 psi 189.737 psi 0.0909 OK

Page 36
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Tower Foundation - CASE 2 (Biiaxial Analysis)

Punching Shear All units k

Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+0.90D+W+0.90H 13.586 psi 189.737 psi 0.0716 OK
+0.90D+E+0.90H 12.935 psi 189.737 psi 0.06817 OK

Page 37
 SECTION B:

CALCULATIONS FOR
EQUIPMENT BUILDING FOUNDATION
AND ANCHORAGE

Page 38
/ ROOF

Page 39
INTERMEDIATE (ASSUMED FOR SDC D)

Page 40
• Kd • V2 (EQ. 27.3-1)

Page 41
Page 42
Page 43
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Building Foundation

Code References
ACI 318-11,
Calculations per ACI 318-14, IBC
IBC 2012,
2015, CBC
CBC 2013,
2016, ASCE 7-10
Load Combinations Used : IBC 2012
General Information
Material Properties Soil Design Values
f'c : Concrete 28 day strength = 3.0 ksi Allowable Soil Bearing = 1.50 ksf
fy : Rebar Yield = 60.0 ksi Increase Bearing By Footing Weight = No
Ec : Concrete Elastic Modulus = 3,122.0 ksi Soil Passive Resistance (for Sliding) = 100.0 pcf
Concrete Density = 145.0 pcf Soil/Concrete Friction Coeff. = 0.350
Values Flexure = 0.90
Shear = 0.750 Increases based on footing Depth
Analysis Settings Footing base depth below soil surface = 1.50 ft
Min Steel % Bending Reinf. = Allowable pressure increase per foot of depth= ksf
Min Allow % Temp Reinf. = 0.00090 when footing base is below = ft
Min. Overturning Safety Factor = 1.0 : 1
Min. Sliding Safety Factor = 1.0 : 1 Increases based on footing plan dimension
Add Ftg Wt for Soil Pressure : Yes Allowable pressure increase per foot of depth= ksf
Use ftg wt for stability, moments & shears : Yes when maximum length or width is greater =than ft
Add Pedestal Wt for Soil Pressure : No
Use Pedestal wt for stability, mom & shear : No
Dimensions
Width parallel to X-X Axis = 17.0 ft 16'-0"
Length parallel to Z-Z Axis = 11.0 ft Z
Footing Thickness = 6.0 in
11'-0"

10'-0"
Pedestal dimensions... X X
px : parallel to X-X Axis = 192.0 in
pz : parallel to Z-Z Axis = 120.0 in
=
5'-6"

Height 0.010 in

Edge Dist. = 3"

Rebar Centerline to Edge of Concrete...
at Bottom of footing = 3.0 in

8'-6"
Reinforcing 17'-0"
Z
Bars parallel to X-X Axis
Number of Bars = 10.0
Reinforcing Bar Size = # 5
Bars parallel to Z-Z Axis
Number of Bars = 17
Reinforcing Bar Size = # 5 10 - # 5 Bars 17 - # 5 Bars
3"

3"

X-X Section Looking to +Z Z-Z Section Looking to +X

Bandwidth Distribution Check (ACI 15.4.4.2)

Direction Requiring Closer Bars
Separation
along Z-Z Axis
# Bars required within zone 78.6 %
# Bars required on each side of zone 21.4 %
Applied Loads
D Lr L S W E H
P : Column Load = 50.0 k
OB : Overburden = ksf
M-xx = 24.0 195.0 k-ft
M-zz = k-ft
V-x = k
V-z = 4.80 19.50 k

Page 44
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Building Foundation

DESIGN SUMMARY Design OK

Min. Ratio Item Applied Capacity Governing Load Combination
PASS 0.5625 Soil Bearing 0.8438 ksf 1.50 ksf +0.60D+0.70E+0.60H about X-X axis
PASS 1.463 Overturning - X-X 143.336 k-ft 209.740 k-ft +0.60D+0.70E+0.60H
PASS n/a Overturning - Z-Z 0.0 k-ft 0.0 k-ft No Overturning
PASS n/a Sliding - X-X 0.0 k 0.0 k No Sliding
PASS 1.056 Sliding - Z-Z 13.650 k 14.410 k +0.60D+0.70E+0.60H
PASS n/a Uplift 0.0 k 0.0 k No Uplift
PASS 0.01338 Z Flexure (+X) 0.04623 k-ft 3.454 k-ft +1.408D+0.50L+0.70S+E+1.60H
PASS 0.01338 Z Flexure (-X) 0.04623 k-ft 3.454 k-ft +1.408D+0.50L+0.70S+E+1.60H
PASS 0.06099 X Flexure (+Z) 0.2294 k-ft 3.761 k-ft +0.6918D+E+0.90H
PASS 0.01232 X Flexure (-Z) 0.04632 k-ft 3.761 k-ft +1.40D+1.60H
PASS 0.03607 1-way Shear (+X) 2.963 psi 82.158 psi +1.408D+0.50L+0.70S+E+1.60H
PASS 0.03607 1-way Shear (-X) 2.963 psi 82.158 psi +1.408D+0.50L+0.70S+E+1.60H
PASS 0.1191 1-way Shear (+Z) 9.784 psi 82.158 psi +0.6918D+E+0.90H
PASS 0.02320 1-way Shear (-Z) 1.906 psi 82.158 psi +1.40D+1.60H
PASS 0.06984 2-way Punching 6.279 psi 89.909 psi +0.6918D+E+0.90H
Detailed Results
Soil Bearing
Rotation Axis & Actual Soil Bearing Stress Actual / Allowable
Load Combination... Gross Allowable Xecc Zecc Bottom, -Z Top, +Z Left, -X Right, +X Ratio
X-X, +D+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+L+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+Lr+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+S+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+0.750Lr+0.750L+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+0.750L+0.750S+H 1.50 n/a 0.0 0.3399 0.3399 n/a n/a 0.227
X-X, +D+0.60W+H 1.50 n/a 2.991 0.2944 0.3853 n/a n/a 0.257
X-X, +D+0.70E+H 1.50 n/a 27.063 0.0 0.7609 n/a n/a 0.507
X-X, +D+0.750Lr+0.750L+0.450W+H 1.50 n/a 2.243 0.3058 0.3740 n/a n/a 0.249
X-X, +D+0.750L+0.750S+0.450W+H 1.50 n/a 2.243 0.3058 0.3740 n/a n/a 0.249
X-X, +D+0.750L+0.750S+0.5250E+H 1.50 n/a 20.297 0.03154 0.6482 n/a n/a 0.432
X-X, +0.60D+0.60W+0.60H 1.50 n/a 4.985 0.1585 0.2494 n/a n/a 0.166
X-X, +0.60D+0.70E+0.60H 1.50 n/a 45.104 0.0 0.8438 n/a n/a 0.563
Z-Z, +D+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+L+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+Lr+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+S+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.750Lr+0.750L+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.750L+0.750S+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.60W+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.70E+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.750Lr+0.750L+0.450W+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.750L+0.750S+0.450W+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +D+0.750L+0.750S+0.5250E+H 1.50 0.0 n/a n/a n/a 0.3399 0.3399 0.227
Z-Z, +0.60D+0.60W+0.60H 1.50 0.0 n/a n/a n/a 0.2039 0.2039 0.136
Z-Z, +0.60D+0.70E+0.60H 1.50 0.0 n/a n/a n/a 0.2039 0.2039 0.136
Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+H None 0.0 k-ft Infinity OK
X-X, +D+L+H None 0.0 k-ft Infinity OK
X-X, +D+Lr+H None 0.0 k-ft Infinity OK
X-X, +D+S+H None 0.0 k-ft Infinity OK
X-X, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
X-X, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
X-X, +D+0.60W+H 15.842 k-ft 349.566 k-ft 22.065 OK
X-X, +D+0.70E+H 143.336 k-ft 349.566 k-ft 2.439 OK
X-X, +D+0.750Lr+0.750L+0.450W+H 11.882 k-ft 349.566 k-ft 29.420 OK
X-X, +D+0.750L+0.750S+0.450W+H 11.882 k-ft 349.566 k-ft 29.420 OK

Page 45
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Building Foundation

Overturning Stability
Rotation Axis &
Load Combination... Overturning Moment Resisting Moment Stability Ratio Status
X-X, +D+0.750L+0.750S+0.5250E+H 107.502 k-ft 349.566 k-ft 3.252 OK
X-X, +0.60D+0.60W+0.60H 15.842 k-ft 209.740 k-ft 13.239 OK
X-X, +0.60D+0.70E+0.60H 143.336 k-ft 209.740 k-ft 1.463 OK
Z-Z, +D+H None 0.0 k-ft Infinity OK
Z-Z, +D+L+H None 0.0 k-ft Infinity OK
Z-Z, +D+Lr+H None 0.0 k-ft Infinity OK
Z-Z, +D+S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.60W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.70E+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+0.450W+H None 0.0 k-ft Infinity OK
Z-Z, +D+0.750L+0.750S+0.5250E+H None 0.0 k-ft Infinity OK
Z-Z, +0.60D+0.60W+0.60H None 0.0 k-ft Infinity OK
Z-Z, +0.60D+0.70E+0.60H None 0.0 k-ft Infinity OK
Sliding Stability All units k
Force Application Axis
Load Combination... Sliding Force Resisting Force Sliding SafetyRatio Status
X-X, +D+H 0.0 k 22.933 k No Sliding OK
X-X, +D+L+H 0.0 k 22.933 k No Sliding OK
X-X, +D+Lr+H 0.0 k 22.933 k No Sliding OK
X-X, +D+S+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.750Lr+0.750L+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.750L+0.750S+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.60W+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.70E+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.750Lr+0.750L+0.450W+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.750L+0.750S+0.450W+H 0.0 k 22.933 k No Sliding OK
X-X, +D+0.750L+0.750S+0.5250E+H 0.0 k 22.933 k No Sliding OK
X-X, +0.60D+0.60W+0.60H 0.0 k 14.035 k No Sliding OK
X-X, +0.60D+0.70E+0.60H 0.0 k 14.035 k No Sliding OK
Z-Z, +D+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+L+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+Lr+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+S+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+0.750Lr+0.750L+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+0.750L+0.750S+H 0.0 k 23.308 k No Sliding OK
Z-Z, +D+0.750L+0.750S+0.450W+H 2.160 k 23.308 k 10.791 OK
Z-Z, +D+0.750L+0.750S+0.5250E+H 10.238 k 23.308 k 2.277 OK
Z-Z, +0.60D+0.60W+0.60H 2.880 k 14.410 k 5.003 OK
Z-Z, +0.60D+0.70E+0.60H 13.650 k 14.410 k 1.056 OK
Z-Z, +D+0.60W+H 2.880 k 23.308 k 8.093 OK
Z-Z, +D+0.70E+H 13.650 k 23.308 k 1.708 OK
Z-Z, +D+0.750Lr+0.750L+0.450W+H 2.160 k 23.308 k 10.791 OK
Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.40D+1.60H 0.04632 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.40D+1.60H 0.04632 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 0.03971 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50Lr+1.60L+1.60H 0.03971 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60L+0.50S+1.60H 0.03971 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60L+0.50S+1.60H 0.03971 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 0.03971 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60Lr+0.50L+1.60H 0.03971 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 0.04432 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60Lr+0.50W+1.60H 0.03509 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50L+1.60S+1.60H 0.03971 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50L+1.60S+1.60H 0.03971 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+1.60S+0.50W+1.60H 0.04432 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK

Page 46
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Building Foundation

Footing Flexure
Flexure Axis & Load Combination Mu Which Tension @ As Req'd Gvrn. As Actual As Phi*Mn Status
k-ft Side ? Bot or Top ? in^2 in^2 in^2 k-ft
X-X, +1.20D+1.60S+0.50W+1.60H 0.03509 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 0.04893 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50Lr+0.50L+W+1.60H 0.03048 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 0.04893 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.20D+0.50L+0.50S+W+1.60H 0.03048 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.408D+0.50L+0.70S+E+1.60H 0.1201 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +1.408D+0.50L+0.70S+E+1.60H 0.01263 -Z Top 0.0648 Min Temp % 0.310 3.761 OK
X-X, +0.90D+W+0.90H 0.03901 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +0.90D+W+0.90H 0.02055 -Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +0.6918D+E+0.90H 0.2294 +Z Bottom 0.0648 Min Temp % 0.310 3.761 OK
X-X, +0.6918D+E+0.90H 0.006207 -Z Top 0.0648 Min Temp % 0.310 3.761 OK
Z-Z, +1.40D+1.60H 0.04596 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.40D+1.60H 0.04596 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50Lr+1.60L+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60L+0.50S+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60Lr+0.50L+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60Lr+0.50W+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50L+1.60S+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+1.60S+0.50W+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50Lr+0.50L+W+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 0.03939 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.20D+0.50L+0.50S+W+1.60H 0.03939 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.408D+0.50L+0.70S+E+1.60H 0.04623 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +1.408D+0.50L+0.70S+E+1.60H 0.04623 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +0.90D+W+0.90H 0.02955 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +0.90D+W+0.90H 0.02955 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +0.6918D+E+0.90H 0.02271 -X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
Z-Z, +0.6918D+E+0.90H 0.02271 +X Bottom 0.0648 Min Temp % 0.2818 3.454 OK
One Way Shear
Load Combination... Vu @ -X Vu @ +X Vu @ -Z Vu @ +Z Vu:Max Phi Vn Vu / Phi*Vn Status
+1.40D+1.60H 2.946 psi 2.946 psi 1.906 psi 1.906 psi 2.946 psi 82.158 psi 0.03586 OK
+1.20D+0.50Lr+1.60L+1.60H 2.525 psi 2.525 psi 1.634 psi 1.634 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+1.60L+0.50S+1.60H 2.525 psi 2.525 psi 1.634 psi 1.634 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+1.60Lr+0.50L+1.60H 2.525 psi 2.525 psi 1.634 psi 1.634 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+1.60Lr+0.50W+1.60H 2.525 psi 2.525 psi 1.441 psi 1.827 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+0.50L+1.60S+1.60H 2.525 psi 2.525 psi 1.634 psi 1.634 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+1.60S+0.50W+1.60H 2.525 psi 2.525 psi 1.441 psi 1.827 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+0.50Lr+0.50L+W+1.60H 2.525 psi 2.525 psi 1.248 psi 2.02 psi 2.525 psi 82.158 psi 0.03074 OK
+1.20D+0.50L+0.50S+W+1.60H 2.525 psi 2.525 psi 1.248 psi 2.02 psi 2.525 psi 82.158 psi 0.03074 OK
+1.408D+0.50L+0.70S+E+1.60H 2.963 psi 2.963 psi 0.5199 psi 4.992 psi 4.992 psi 82.158 psi 0.06076 OK
+0.90D+W+0.90H 1.894 psi 1.894 psi 0.8398 psi 1.611 psi 1.894 psi 82.158 psi 0.02305 OK
+0.6918D+E+0.90H 1.456 psi 1.456 psi 0.2554 psi 9.784 psi 9.784 psi 82.158 psi 0.1191 OK
Punching Shear All units k
Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+1.40D+1.60H 3.587 psi 89.909 psi 0.0399 OK
+1.20D+0.50Lr+1.60L+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+1.60L+0.50S+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+1.60Lr+0.50L+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+1.60Lr+0.50W+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+0.50L+1.60S+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+1.60S+0.50W+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+0.50Lr+0.50L+W+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.20D+0.50L+0.50S+W+1.60H 3.075 psi 89.909 psi 0.0342 OK
+1.408D+0.50L+0.70S+E+1.60H 3.97 psi 89.909 psi 0.04416 OK

Page 47
 File = U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\419 Structural\rainbow tower.ec6
General Footing ENERCALC, INC. 1983-2015, Build:6.15.3.9, Ver:6.15.3.9
Lic. # : KW-06005615 Licensee : aecom
Description : Building Foundation

Punching Shear All units k

Load Combination... Vu Phi*Vn Vu / Phi*Vn Status
+0.90D+W+0.90H 2.306 psi 89.909 psi 0.02565 OK
+0.6918D+E+0.90H 6.279 psi 89.909 psi 0.06984 OK

Page 48
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 1
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

Specifier's comments: Building Embed Plate Anchorage

1 Input data
Anchor type and diameter: AWS D1.1 GR. B 3/4
Effective embedment depth: hef = 11.000 in.
Material:
Proof: Design method ACI 318-14 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 1.000 in.
Anchor plate: lx x ly x t = 197.000 in. x 125.000 in. x 1.000 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 4000, fc' = 4000 psi; h = 21.000 in.
Reinforcement: tension: condition B, shear: condition A; anchor reinforcement: shear
edge reinforcement: none or < No. 4 bar
Seismic loads (cat. C, D, E, or F) Tension load: yes (17.2.3.4.3 (d))
Shear load: yes (17.2.3.5.3 (c))

Geometry [in.] & Loading [kip, ft.kip]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 49
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 2
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

2 Load case/Resulting anchor forces y

Load case: Design loads

Anchor reactions [kip]

Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 3.339 2.251 -0.119 -2.248
2 3.339 2.262 -0.119 -2.259
3 3.339 2.273 -0.119 -2.270 678 321
9 Tension 4
4 3.178 2.250 -0.108 -2.248 10 5
5 3.017 2.250 -0.097 -2.248
6 3.339 2.630 -0.119 -2.627
7 3.339 2.619 -0.119 -2.616
x
8 3.339 2.608 -0.119 -2.605
9 3.178 2.629 -0.108 -2.627
10 3.017 2.629 -0.097 -2.627
11 0.000 2.251 0.119 -2.248 20 15
19 14
12 0.000 2.262 0.119 -2.259 16
1718 13
1211
Compression
13 0.000 2.273 0.119 -2.270
14 0.000 2.250 0.108 -2.248
15 0.152 2.250 0.097 -2.248
16 0.000 2.630 0.119 -2.627
17 0.000 2.619 0.119 -2.616
18 0.000 2.608 0.119 -2.605
19 0.000 2.629 0.108 -2.627
20 0.152 2.629 0.097 -2.627
max. concrete compressive strain: 0.02 [‰]
max. concrete compressive stress: 82 [psi]
resulting tension force in (x/y)=(0.000/55.891): 32.725 [kip]
resulting compression force in (x/y)=(0.000/-59.734): 67.315 [kip]

3 Tension load
Load Nua [kip] Capacity f Nn [kip] Utilization bN = Nua/f Nn Status
Steel Strength* 3.339 21.547 16 OK
Pullout Strength* 3.339 13.188 26 OK
Concrete Breakout Strength** 32.725 37.101 89 OK
Concrete Side-Face Blowout, direction ** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (anchors in tension)

3.1 Steel Strength

Nsa = Ase,N futa ACI 318-14 Eq. (17.4.1.2)
f Nsa ≥ Nua ACI 318-14 Table 17.3.1.1

Variables
Ase,N [in.2] futa [psi]
0.44 65000
Calculations
Nsa [kip]
28.730
Results
Nsa [kip] f steel f Nsa [kip] Nua [kip]
28.730 0.750 21.547 3.339

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 50
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 3
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

3.2 Pullout Strength

NpN = y c,p Np ACI 318-14 Eq. (17.4.3.1)
Np = 8 Abrg f'c ACI 318-14 Eq. (17.4.3.4)
f NpN ≥ Nua ACI 318-14 Table 17.3.1.1

Variables
y c,p Abrg [in.2] la f'c [psi]
1.000 0.79 1.000 4000
Calculations
Np [kip]
25.120
Results
Npn [kip] f concrete f seismic f nonductile f Npn [kip] Nua [kip]
25.120 0.700 0.750 1.000 13.188 3.339

3.3 Concrete Breakout Strength

Ncbg = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nb ACI 318-14 Eq. (17.4.2.1b)
f Ncbg ≥ Nua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
ANc0 = 9 h2ef ACI 318-14 Eq. (17.4.2.1c)

( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-14 Eq. (17.4.2.5b)

y cp,N = MAX
cac(
ca,min 1.5hef
,
cac )
≤ 1.0 ACI 318-14 Eq. (17.4.2.7b)
5/3
Nb = 16 l a √f'c hef ACI 318-14 Eq. (17.4.2.2b)

Variables
hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.] y c,N
11.000 0.000 16.807 6.000 1.000

cac [in.] kc la f'c [psi]

- 16 1.000 4000

Calculations
ANc [in.2] ANc0 [in.2] y ec1,N y ec2,N y ed,N y cp,N Nb [kip]
3487.50 1089.00 1.000 0.495 0.809 1.000 55.056
Results
Ncbg [kip] f concrete f seismic f nonductile f Ncbg [kip] Nua [kip]
70.669 0.700 0.750 1.000 37.101 32.725

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 51
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 4
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

4 Shear load
Load Vua [kip] Capacity f Vn [kip] Utilization bV = Vua/f Vn Status
Steel Strength* 2.630 18.674 15 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 48.750 144.993 34 OK
Concrete edge failure in direction ** 1 N/A N/A N/A N/A
* anchor having the highest loading **anchor group (relevant anchors)
1
Shear Anchor Reinforcement has been selected!

4.1 Steel Strength

Vsa = Ase,V futa ACI 318-14 Eq. (17.5.1.2a)
f Vsteel ≥ Vua ACI 318-14 Table 17.3.1.1

Variables
Ase,V [in.2] futa [psi]
0.44 65000
Calculations
Vsa [kip]
28.730
Results
Vsa [kip] f steel f Vsa [kip] Vua [kip]
28.730 0.650 18.674 2.630

4.2 Pryout Strength

Vcpg = kcp [(AA ) y

Nc
Nc0
ec,N ]
y ed,N y c,N y cp,N Nb ACI 318-14 Eq. (17.5.3.1b)
f Vcpg ≥ Vua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
ANc0 = 9 h2ef ACI 318-14 Eq. (17.4.2.1c)

( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-14 Eq. (17.4.2.5b)

y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 ACI 318-14 Eq. (17.4.2.7b)
5/3
Nb = 16 l a √f'c hef ACI 318-14 Eq. (17.4.2.2b)

Variables
kcp hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.]
2 11.000 9.600 0.000 6.000

y c,N cac [in.] kc la f'c [psi]

1.000 - 16 1.000 4000

Calculations
ANc [in.2] ANc0 [in.2] y ec1,N y ec2,N y ed,N y cp,N Nb [kip]
4005.00 1089.00 0.632 1.000 0.809 1.000 55.056
Results
Vcpg [kip] f concrete f seismic f nonductile f Vcpg [kip] Vua [kip]
207.133 0.700 1.000 1.000 144.993 48.750

5 Combined tension and shear loads

bN bV z Utilization bN,V [%] Status
0.882 0.336 5/3 98 OK

bNV = bzN + bzV <= 1

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 52
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 5
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
• Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant
standard!
• An anchor design approach for structures assigned to Seismic Design Category C, D, E or F is given in ACI 318-14, Chapter 17, Section
17.2.3.4.3 (a) that requires the governing design strength of an anchor or group of anchors be limited by ductile steel failure. If this is NOT
the case, the connection design (tension) shall satisfy the provisions of Section 17.2.3.4.3 (b), Section 17.2.3.4.3 (c), or Section 17.2.3.4.3
(d). The connection design (shear) shall satisfy the provisions of Section 17.2.3.5.3 (a), Section 17.2.3.5.3 (b), or Section 17.2.3.5.3 (c).
• Section 17.2.3.4.3 (b) / Section 17.2.3.5.3 (a) require the attachment the anchors are connecting to the structure be designed to undergo
ductile yielding at a load level corresponding to anchor forces no greater than the controlling design strength. Section 17.2.3.4.3 (c) / Section
17.2.3.5.3 (b) waive the ductility requirements and require the anchors to be designed for the maximum tension / shear that can be
transmitted to the anchors by a non-yielding attachment. Section 17.2.3.4.3 (d) / Section 17.2.3.5.3 (c) waive the ductility requirements and
require the design strength of the anchors to equal or exceed the maximum tension / shear obtained from design load combinations that
include E, with E increased by w0.
• The design of Anchor Reinforcement is beyond the scope of PROFIS Anchor. Refer to ACI 318-14, Section 17.5.2.9 for information about
Anchor Reinforcement.
• Anchor Reinforcement has been selected as a design option, calculations should be compared with PROFIS Anchor calculations.

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 53
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 6
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

7 Installation data
Anchor plate, steel: - Anchor type and diameter: AWS D1.1 GR. B 3/4
Profile: no profile Installation torque: -
Hole diameter in the fixture: df = 0.813 in. Hole diameter in the base material: - in.
Plate thickness (input): 1.000 in. Hole depth in the base material: 11.000 in.
Recommended plate thickness: not calculated Minimum thickness of the base material: 11.875 in.
Drilling method: -
Cleaning: No cleaning of the drilled hole is required

98.500 98.500

2.500
5.500
6 7 8 3 2 1

5.500
9 4
10 5

62.500
98.000
x

62.500
5.500

20 15
5.500

19 14
2.500

16 17 18 13 12 11
2.500
5.500
5.500 170.000 5.500
5.500
2.500

Coordinates Anchor in.

Anchor x y c-x c+x c-y c+y Anchor x y c-x c+x c-y c+y
1 96.000 60.000 198.000 6.000 126.000 6.000 11 96.000 -60.000 198.000 6.000 6.000 126.000
2 90.500 60.000 192.500 11.500 126.000 6.000 12 90.500 -60.000 192.500 11.500 6.000 126.000
3 85.000 60.000 187.000 17.000 126.000 6.000 13 85.000 -60.000 187.000 17.000 6.000 126.000
4 96.000 54.500 198.000 6.000 120.500 11.500 14 96.000 -54.500 198.000 6.000 11.500 120.500
5 96.000 49.000 198.000 6.000 115.000 17.000 15 96.000 -49.000 198.000 6.000 17.000 115.000
6 -96.000 60.000 6.000 198.000 126.000 6.000 16 -96.000 -60.000 6.000 198.000 6.000 126.000
7 -90.500 60.000 11.500 192.500 126.000 6.000 17 -90.500 -60.000 11.500 192.500 6.000 126.000
8 -85.000 60.000 17.000 187.000 126.000 6.000 18 -85.000 -60.000 17.000 187.000 6.000 126.000
9 -96.000 54.500 6.000 198.000 120.500 11.500 19 -96.000 -54.500 6.000 198.000 11.500 120.500
10 -96.000 49.000 6.000 198.000 115.000 17.000 20 -96.000 -49.000 6.000 198.000 17.000 115.000

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 54
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: AECOM Page: 7
Specifier: DAH Project: Rainbow Tower
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 7/14/2017
E-Mail:

8 Remarks; Your Cooperation Duties

• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
Page 55
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Page 56
 SECTION C:

CALCULATION ATTACHMENTS

Page 57
ATTACHMENT #1

Page 58
ATTACHMENT #2

Crest Height = 1948' - 853' = 1095' (Use 1100')

Page 59
 APPENDIX A:

Owner-Provided Appurtenance List

and Equipment Data Sheets

Page 60
Owner Provided Appurtenance List
Number/ Type
Antenna of
Attachment Approx Transmission
level Owner Antenna Location Azimuth Antenna Make or Size Antenna Model Frewq. Range Lines Color Code Mount Type/ Size
Telewave/ 256" Omni Antenna
40' SD County LEG #1 N/A ANT150F6-3 DIN N/A 1 / LDF5 N/A 2' standoff Pipe to Pipe/ 2-3/8" OD pipe
6dBd Fiberglass Collinear Antenna
Telewave/ 256" Omni Antenna
40' SD County LEG #2 N/A ANT150F6-3 DIN N/A 1/ LDF5 N/A 2' standoff Pipe to Pipe/ 2-3/8" OD pipe
6dBd Fiberglass Collinear Antenna
Telewave/ 256" Omni Antenna
40' SD County LEG #3 N/A ANT150F6-3 DIN N/A 1 / LDF5 N/A 2' standoff Pipe to Pipe/ 2-3/8" OD pipe
6dBd Fiberglass Collinear Antenna
30' SD County LEG #2 N/A 8' - 0" x 2" Dipole Antenna No MFR Tag N/A 1/ LDF5 Red 1' standoff Pipe to Pipe/ 2-3/8" OD pipe
30' SD County LEG #1 N/A 5' - 6" x 2" Dipole Antenna No MFR Tag N/A 1/ LDF5 Violet 1' standoff Pipe to Pipe/ 2-3/8" OD pipe
20' SD County LEG #2 N/A Hustler Omni Antenna 7' 6" G6-270-R 144-148 MHz 1/ LDF5 Green Green 4' standoff Pipe to Pipe/ 2-3/8" OD pipe
18' SD County LEG #1 N/A Telewave Omni Antenna 244" ANT150F6-3-DIN 150-157 MHz 1/ LDF5 Red Green Whiite 4' standoff Pipe to Pipe/ 2-3/8" OD pipe
Center 20 SD County LEG #1 160 Decible Yagi Antenna DB230-K 160-173 MHz 1/ LDF5 Yellow 1' standoff Pipe to Pipe/ 2-3/8" OD pipe
Center 12' SD County LEG #1 & #2 face mount 195 Andrew MW Antennaa 8' parabolic PAR8-65 6.425-7.125 GHz 1/ EW63 N/A 1' to 2' standoff Pipe to Pipe/ 3-1/2" OD pipe
10' SD County LEG #1 N/A Trimble GPS Antenna 1' 41556-00 N/A 1/ LDF5 Blue Violet 2' standoff Pipe to Pipe/ 2-7/8" OD pipe
18 SD County LEG #3 N/A Telewave Omni Antenna 244" ANT150F6-3-DIN 150-157 MHz 1/ LDF5 Red Breen White White 4' standoff Pipe to Pipe/ 2-3/8" OD pipe

Notes:
1) Additional loading considerations:
a) 10' Lightning Rod @ 40' height
b) 3/8" Diam Safety Line, full height
c) Waveguide Ladder

Page 61
Product Specifications
PAR8
PAR8--65
65--PXA
2.4 m | 8 ft Parabolic Unshielded Antenna for Relocation-Category A, single-polarized,
6.425–7.125 GHz, CPR137G, gray antenna, molded gray radome with flash, standard
pack—one-piece reflector

General Specifications
Antenna Type PAR - Parabolic Unshielded Antenna for Relocation-Category A, single-
polarized
Diameter, nominal 2.4 m | 8 ft
Packing Standard pack
Radome Color Gray
Radome Material Molded
Reflector Construction One-piece reflector
Antenna Input CPR137G
Antenna Color Gray
Antenna Type PAR - Parabolic Unshielded Antenna for Relocation-Category A, single-
polarized
Diameter, nominal 2.4 m | 8 ft
Flash Included Yes
Polarization Single

Electrical Specifications
Operating Frequency Band 6.425 – 7.125 GHz
Beamwidth, Horizontal 1.3 °
Beamwidth, Vertical 1.3 °
Cross Polarization Discrimination (XPD) 30 dB
Electrical Compliance ETSI Class 1 | US FCC Part 101A | US FCC Part 74A
Front-to-Back Ratio 60 dB
Gain, Low Band 41.0 dBi
Gain, Mid Band 40.8 dBi
Gain, Top Band 41.0 dBi
Operating Frequency Band 6.425 – 7.125 GHz
Radiation Pattern Envelope Reference (RPE) 2570B
Return Loss 30.7 dB
VSWR 1.06

Mechanical Specifications
Fine Azimuth Adjustment ±5°
Fine Elevation Adjustment ±5°
Mounting Pipe Diameter 115 mm | 4.5 in
Net Weight 125 kg | 276 lb

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 1 of 5
Page 62
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: May 19, 2017 May 25, 2017
Product Specifications
PAR8
PAR8--65
65--PXA

Side Struts, Included 1 inboard

Side Struts, Optional 3 outboard
Wind Velocity Operational 110 km/h | 68 mph
Wind Velocity Survival Rating 200 km/h | 124 mph

Wind Forces At Wind Velocity Survival Rating

Angle α for MT Max -125 °
Axial Force (FA) 15372 N | 3456 lbf
Side Force (FS) 4196 N | 943 lbf
Twisting Moment (MT) -5349 N•m
Weight with 1/2 in (12 mm) Radial Ice 243 kg | 536 lb
Zcg with 1/2 in (12 mm) Radial Ice 427 mm | 17 in
Zcg without Ice 343 mm | 14 in

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 2 of 5
Page 63
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: May 19, 2017 May 25, 2017
Product Specifications
PAR8
PAR8--65
65--PXA

Wind Forces At Wind Velocity Survival Rating Image

Packed Dimensions
Gross Weight, Packed Antenna 417.0 kg | 919.3 lb
Height 2520.0 mm | 99.2 in
Length 2710.0 mm | 106.7 in
Volume 11.8 m³
Width 1730.0 mm | 68.1 in

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 3 of 5
Page 64
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: May 19, 2017 May 25, 2017
Product Specifications
PAR8
PAR8--65
65--PXA

Antenna Dimensions And Mounting Information

Regulatory Compliance/Certifications
Agency Classification
ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system

* Footnotes
Axial Force (FA) Maximum forces exerted on a supporting structure as a result of wind from
the most critical direction for this parameter. The individual maximums
specified may not occur simultaneously. All forces are referenced to the
mounting pipe.
Cross Polarization Discrimination (XPD) The difference between the peak of the co-polarized main beam and the
maximum cross-polarized signal over an angle twice the 3 dB beamwidth of
the co-polarized main beam.
Front-to-Back Ratio Denotes highest radiation relative to the main beam, at 180° ±40°, across
the band. Production antennas do not exceed rated values by more than 2
dB unless stated otherwise.

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 4 of 5
Page 65
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: May 19, 2017 May 25, 2017
Product Specifications
PAR8
PAR8--65
65--PXA

Gain, Mid Band For a given frequency band, gain is primarily a function of antenna size. The
gain of Andrew antennas is determined by either gain by comparison or by
computer integration of the measured antenna patterns.
Operating Frequency Band Bands correspond with CCIR recommendations or common allocations used
throughout the world. Other ranges can be accommodated on special order.
Packing Andrew standard packing is suitable for export. Antennas are shipped as
standard in totally recyclable cardboard or wire-bound crates (dependent on
product). For your convenience, Andrew offers heavy duty export packing
options.
Radiation Pattern Envelope Reference (RPE) Radiation patterns define an antenna’s ability to discriminate against
unwanted signals. Under still dry conditions, production antennas will not
have any peak exceeding the current RPE by more than 3dB, maintaining an
angular accuracy of +/-1° throughout
Return Loss The figure that indicates the proportion of radio waves incident upon the
antenna that are rejected as a ratio of those that are accepted.
Side Force (FS) Maximum side force exerted on the mounting pipe as a result of wind from
the most critical direction for this parameter. The individual maximums
specified may not occur simultaneously. All forces are referenced to the
mounting pipe.
Twisting Moment (MT) Maximum forces exerted on a supporting structure as a result of wind from
the most critical direction for this parameter. The individual maximums
specified may not occur simultaneously. All forces are referenced to the
mounting pipe.
VSWR Maximum; is the guaranteed Peak Voltage-Standing-Wave-Ratio within the
operating band.
Wind Velocity Operational The wind speed where the antenna deflection is equal to or less than 0.1
degrees. In the case of ValuLine antennas, it is defined as a maximum
deflection of 0.3 x the 3 dB beam width of the antenna.
Wind Velocity Survival Rating The maximum wind speed the antenna, including mounts and radomes,
where applicable, will withstand without permanent deformation.
Realignment may be required. This wind speed is applicable to antenna with
the specified amount of radial ice.

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 5 of 5
Page 66
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: May 19, 2017 May 25, 2017
Page 67
Page 68
Page 69
Installation Instructions Bulletin 237392

Standard, Heavy Duty, and Extended Type

Molded Radomes
for Standard and Focal Plane Parabolic Antennas

Shield Radome

Reflector Mount Feed

Radome

Optional

Sequence of Antenna Assembly

Description
These radomes reduce the windload on standard and
focal plane antennas, and protect the feeds from weath- Reflector
er and physical damage.
Radome
Weights and measurements are included here to help
you determine how many people will be needed to lift
the radome for placement on the reflector.

Notice
The installation, maintenance, or removal of antenna
systems requires qualified, experienced personnel.
Andrew installation instructions have been written for
such personnel. Antenna systems should be inspected
once a year by qualified personnel to verify proper
installation, maintenance, and condition of equipment.
Andrew disclaims any liability or responsibility for the
results of improper or unsafe installation practices.

Antenna mounting
Tools pipe on tower
Standard hand tools can be used for this installation. A
ratchet and deep well wrench sockets are recommend-
ed. However, combination wrenches, box or open-end
type, may be used. Wrench sizes for the furnished bolt
hardware are as follows:
Radome size Wrench size Bolt size
0.6-3.0 m (2-10ft) 10 mm M6
3.7 m (12 ft) 13 mm M8

Page 70
 Radome Net weight Dimension A Dimension B Mounting
m ft kg lb mm in mm in holes

Standard
Extended
0.6 2 2 4 705 27.75 305 12 6
1.2 4 6 13 1283 50.5 470 18.5 6 Standard and
1.8 6 16 36 1930 76 692 27.25 9 heavy duty
2.4 8 34 74 2515 99 908 35.75 12 B
3.0 10 41 90 3124 123 832 32.75 16
3.7 12 67 147 3772 148 940 37 18

Heavy Duty A
3.0 10 49 107 3124 123 838 33 16
3.7 12 77 170 3772 148 940 37 18

Extended
2.4 8 25 54 1930 76 940 37 12

1
Align tape
markers (top
of antenna)

Align holes with

screwdriver

2
Nut
Lock washer
M6/M8 M6 - 8 N·m (6 lb·ft)
Flat washer M8 - 19 N·m (14 lb·ft)
M6 or
Flat washer
M8 bolt

Inches 1 2 3 4 5 6 7

Millimeters 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180

Andrew Corporation Telephone: 708-349-3300 Customer Service, 24 hours: U.S.A. • Canada • Mexico: 1-800-255-1479
10500 West 153rd Street FAX (U.S.A.): 1-800-349-5444 U.K.: 0800 250055 • Republic of Ireland: 1 800 535358 Printed in U.S.A. 7/97
Orland Park, IL U.S.A. 60462 Internet: http://www.andrew.com Other Europe: +44 1592 782612 Copyright © 1997 by Andrew Corporation
Page 71
Page 72
Page 73
Page 74
Page 75
Page 76
Page 77
 APPENDIX B:

Geotechnical Investigation Letter Report for the

“Proposed Control Shelter and Communications Tower”
by AECOM, dated July 13, 2017

Page 78
 AECOM 858-812-9292 tel
4225 Executive Square 858-812-9293 fax
Suite 1400
La Jolla, CA 92037
www.aecom.com

July 13, 2017

Mr. Prince Dumaran

Project Manager
Harris and Associates
600 B Street, Suite 2000
San Diego, California 92101

Subject: Geotechnical Investigation Letter Report

Proposed Control Shelter and Communications Tower
6778 Rainbow Peaks Road
Fallbrook, California
AECOM Project Number: 60543652

Dear Mr. Dumaran:

AECOM Technical Services, Inc. (AECOM) is pleased to provide this report presenting our
geotechnical evaluation for the proposed Control Shelter and Communications Tower at 6778
Rainbow Peaks Road in Fallbrook, California. This report presents the findings from a geotechnical
investigation completed by AECOM at the project and discusses geotechnical engineering design and
construction considerations to support proposed site improvements.
PROJECT UNDERSTANDING

The project site is located southwest of the intersection of Rainbow Peaks Road and Rainbow
Heights Road within a gated facility owned by the San Diego County Sheriffs Department in
Fallbrook, California. A new control shelter is proposed to replace the existing equipment building
that is approximately 8 feet wide by 20 feet long. Replacement of the existing communications tower
and associated foundation, just west of the existing equipment building, is also planned. The existing
tower foundation slab is a 7 foot concrete square. The southern end of site slopes down
approximately 60 feet at an inclination of approximately 2H:1V (Horizontal to Vertical) to Rainbow
Peaks Road. Figure 1 presents a Vicinity Map of the project site.

PURPOSE AND SCOPE

The purpose of our investigation is to evaluate the subsurface conditions at the project site and
provide geotechnical design recommendations with respect to the planned improvements. Since the
soils encountered during the subsurface investigation were homogenous and easily characterized, a
laboratory testing program was not warranted. The scope of services included:

· Performing a site reconnaissance.

· Performing hand auguring and logging of three shallow borings.
· Performing engineering analyses.
· Preparing this report with findings, conclusions and geotechnical evaluation.

U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\Geotech\2017_07_13_Fallbrook Tower Geotech Letter Report

(AECOM_Final)_Rev.doc
Page 79
Mr. Prince Dumaran
Harris and Associates
July 13, 2017
Page 2

SUBSURFACE INVESTIGATION

Subsurface exploration consisted of logging and obtaining soil samples from three hand auger
borings (designated HA-1 through HA-3) that were advanced to depths ranging from 2.5 to 4.3 feet
below ground surface (bgs). An AECOM geotechnical engineer advanced and logged the borings,
and retained grab samples of the representative materials. Figure 2 shows the locations of the
subsurface explorations. Attachment A provides logs of the test borings.

SUBSURFACE CONDITIONS

Based on our subsurface explorations, the site is underlain by undocumented fill comprised of silty
sand with gravel and residual soils (derived from decomposed granite) to a depth of about 3.5 feet
over completely weathered granite rock . Groundwater was not encountered in the explorations and is
expected to be deeper than the proposed improvement foundations.

CONCLUSIONS AND RECOMMENDATIONS

In our opinion, the proposed development is geotechnically feasible. The following sections present
our recommendations for the design of the proposed improvements and provide seismic design
coefficients in accordance with 2016 California Building Code (CBC).

We expect the proposed improvements will be supported on shallow foundations and concrete slabs-
on-grade. Foundations and slabs should be supported on engineered fill.

Seismic Design Parameters

The project area will likely be subject to moderate to severe ground shaking in response to a local or
more distant large-magnitude earthquakes occurring during the expected life of the proposed
facilities. The table below presents the seismic design coefficients based on 2016 CBC. These
parameters are developed in the code, based on Risk-Targeted Maximum Considered Earthquake
(MCER) ground motion response accelerations.

2016 CBC Seismic Coefficients

Parameter Value Reference

Site Class D ASCE 7-10, Table 20.3-1
Mapped Spectral Acceleration - Short Period, Ss (g) 1.562 2016 CBC Figure 1613.3.1(2)1
Mapped Spectral Acceleration - 1 Sec. Period, S1 (g) 0.616 2016 CBC Figure 1613.5(4)1
Site Coefficient - Short Period, Fa 1.000 2016 CBC Table 1613.3.3(1)1
Site Coefficient - 1 Sec. Period, Fv 1.500 2016 CBC Table 1613.3.3(2)1
MCE2 Spectral Response Acceleration - Short Period, SMS (g) 1.562 2016 CBC Equation 16-37, SMS=FaSS

U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\Geotech\2017_07_13_Fallbrook Tower Geotech Letter Report

(AECOM_Final)_Rev.doc

Page 80
Mr. Prince Dumaran
Harris and Associates
July 13, 2017
Page 3

Parameter Value Reference

MCE2 Spectral Response Acceleration - 1 Sec. Period, SM1 (g) 0.925 2016 CBC Equation 16-38, SM1=FvS1
Design Spectral Response Acceleration - Short Period, SDS (g) 1.041 2016 CBC Equation 16-39, SDS=2/3*SMS
Design Spectral Response Acceleration - 1 Sec. Period, SD1 (g) 0.616 2016 CBC Equation 16-40, SD1=2/3*SM1
Notes:
1. Calculated using U.S. Seismic Design Maps web application developed by USGS.
2. MCE – Maximum Considered Earthquake.
3. Site coordinates estimated from ‘Google Earth’ computer program used to evaluate coefficients: 33.408N; 117.127W.

Earthwork

Weeds, grass, trees, shrubs and construction debris within areas of proposed improvements should
be cleared and properly disposed of off-site. Roots and other vegetative matter should be removed
and disposed either offsite or stockpiled for reuse in landscape areas. Existing infrastructure should
be properly demolished and disposed at an appropriate facility offsite.

Removal of existing undocumented fill and residual soil is required to expose suitable material on
which to place fill. Removals should generally extend into competent weathered rock as observed
and approved by a Geotechnical Engineer. Removal depths should generally be four feet or less,
except in local areas. A Geotechnical Engineer should make the final determination of actual removal
depths in the field during earthwork. There may be local areas of removal to other firm, native
materials as approved by the Geotechnical Engineer.

Following the clearing of weeds, grass and debris, and upon completion of removals, the surface
within areas to receive fill should be scarified, moisture conditioned as necessary, and compacted
prior to fill placement. Areas temporarily vacated during earthwork should be similarly scarified,
moisture conditioned and reworked to the satisfaction of a Geotechnical Engineer before placing
additional fill to avoid drying out and lamination along the fill interface.

Except for surficial organic materials, the onsite surficial deposits including the properly processed
residual soil and weathered rock are suitable for use as engineered fill. Rock fragments and clasts
that are greater than six inches in maximum dimension should be screened. Import materials are not
expected to be needed.

Fill soils should be placed in loose horizontal lifts that do not exceed 8 inches. Each layer should be
spread evenly and thoroughly mixed during spreading to obtain a uniform moisture content and soil
composition in each layer. After each layer has been mixed and spread, it should be compacted to a
relative compaction indicated by tests to be not less than 90 percent. Relative compaction is defined as
the ratio (expressed in percent) of the in-place dry unit weight of the compacted fill divided by the
maximum dry unit weight evaluated in accordance with ASTM D1557. Fill materials should be
compacted at a moisture content of 3% above the optimum moisture content determined in accordance
with the above test method.

U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\Geotech\2017_07_13_Fallbrook Tower Geotech Letter Report

(AECOM_Final)_Rev.doc

Page 81
Mr. Prince Dumaran
Harris and Associates
July 13, 2017
Page 4

Shallow Foundations

The foundations may be supported on engineered fill or weathered rock. Due to the size of the
foundations and the proximity to the existing slope, we recommend that the proposed new structures
be supported on mat foundations. Mat foundations may be designed using allowable bearing
pressure of 1,500 pounds per square foot (psf) and should be embedded a minimum of 8 inches
below adjacent grade. The allowable bearing pressure assumes the foundation is located at least 3
feet from the edge of slope. Mat Foundations should be at least 8 inches thick and should be
designed using a modulus of subgrade reaction of 75 pounds per cubic inch (pci). The Structural
Engineer should design the thickness and reinforcement of concrete slabs-on-grade to accommodate
concentrated loads and heavy distributed loads. We understand the mat foundation supporting the
tower may be designed as a turned-down slab on the side closer to the water tank. Allowable bearing
pressures may be increased by one third for short term wind or seismic loads.

Due to foundation proximity to the existing slope, a reduced passive resistance of 100 psf/ft is
recommended for the turned-down concrete slab supporting the building; passive resistance should
be ignored for the tower pad foundation. An allowable friction coefficient of 0.35 may be used with
the dead load to compute the frictional resistance of foundations.

A maximum total settlement of ½-inch and a differential settlement of ¼-inch have been estimated for
uniformly loaded foundations designed for the allowable vertical foundation pressures and other
recommendations provided in this report. This settlement is the result of elastic compression of the
underlying soil. The majority of the settlement due to loading should occur during construction.
Settlement estimates assume that appropriate reinforcement is provided to distribute concentrated
loads across the foundation.

Construction Observation and Testing

Earthwork and placement of engineered fill should be performed under the observation and testing
services of a geotechnical professional supervised by a California-registered Geotechnical Engineer.
Tests should be taken to determine the in-place moisture and relative compaction of engineered fill.
All footing and slab subgrade soils should be observed by a geotechnical or geologic professional
prior to placement of steel and concrete to observe that the subgrade is satisfactory. Excavations
should be free of soft fill or loose and disturbed soils. We recommend that foundation excavations be
cleaned of loose material and that the excavations be observed by a qualified engineer or geologist
before placing steel or concrete to verify soil conditions exposed at the bottoms of the excavations. A
California-registered Geotechnical Engineer should prepare a final report of earthwork testing and
observation.

UNCERTAINTY AND LIMITATIONS

The conclusions and recommendations in the report are based on the information provided to us,
results of our limited field explorations, engineering analyses, and professional judgment. AECOM
U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\Geotech\2017_07_13_Fallbrook Tower Geotech Letter Report
(AECOM_Final)_Rev.doc

Page 82
Mr. Prince Dumaran
Harris and Associates
July 13, 2017
Page 5

should review the final drawings and specifications for compatibility with the recommendations of this
report.

Geotechnical engineering and the geologic sciences are characterized by uncertainty. Professional
judgments presented herein are based on our understanding of the proposed construction and on
general experience. Our engineering work and judgments rendered meet current professional
standards; we do not guarantee the performance of the project in any respect.

CLOSING

We appreciate the opportunity to provide engineering support for this project. Please contact Pallavi
Kumar at 858.812.9292 if you have any questions, comments, or if you need additional information.

Sincerely,

AECOM Technical Services, Inc.

Pallavi Kumar (Balasubramanyam), PE 78540

Project Engineer, Geoengineering

Copy: Mr. Mark Holter, AECOM

Attachments:

U:\Projects\_Jobs\60543652 Radio Tower\400-Technical\Geotech\2017_07_13_Fallbrook Tower Geotech Letter Report

(AECOM_Final)_Rev.doc

Page 83
 PROJECT SITE

VICINITY MAP
CONTROL SHELTER AND COMMUNICATION TOWER
6778 RAINBOW PEAKS ROAD
FALLBROOK, CALIFORNIA

Page 84 1
 X X
X
X

X
X
X
X

X
X

X
X

X
X

X
X

X
X
X

X
X

X
X
X

X
X

X
X

X HA-1

X HA-2

X HA-3
X

X
X
X

Legend
HA-3 Approximate location of exploratory hand auger
boring SITE PLAN
CONTROL SHELTER AND COMUNICATION TOWER
6778 RAINBOW PEAKS ROAD
FALLBROOK, CALIFORNIA

2
Page 85
Attachment A

Page 86
 Project: Fallbrook, COMM Tower
Key to Logs
Project Location: Fallbrook, CA
Project Number: 60543652 Sheet 1 of 1

SAMPLES

Dry Density, pcf

Graphic Log

Dry Density,
Elevation,

MATERIAL DESCRIPTION REMARKS AND

Number
Depth,

OTHER TESTS
Type
feet

feet

pcf
1 2 3 4 5 6 7 8 9 10

COLUMN DESCRIPTIONS

1 Elevation: Elevation in feet referenced to NAVD88 or site 8 Water Content: Water content of soil sample measured in
datum. laboratory, expressed as percentage of dry weight of specimen.
2 Depth: Depth in feet below the ground surface. 9 Dry Unit Weight: Dry unit weight of soil sample measured in
laboratory, in pounds per cubic foot.
3 Sample Type: Type of soil sample collected at depth interval
shown; sampler symbols are explained below. 10 Remarks and Other Tests: Comments and observations
regarding drilling or sampling made by driller or field personnel.
4 Sample Number: Sample identification number.
Unnumbered sample indicates no sample recovery. "1-1" SA Sieve analysis, %<#200 sieve
indicates geotechnical sample. "(B-1@1')" indicates WA Three-point wash sieve, %<#200 sieve
analytical sample. LL Liquid limit (from Atterberg limits test), %
5 Blows per foot: Number of blows required to advance driven PI Plasticity Index [LL - PL], %; NP=nonplastic
sampler 12 inches beyond first 6-inch interval, or distance noted, DS Direct Shear test
using a 140-lb hammer with a 30-inch drop. CORR Corrosivity Test suite
6 Graphic Log: Graphic depiction of subsurface material
encountered; typical symbols are explained below.
7 Material Description: Description of material encountered;
may include relative density/consistency, moisture, color,
particle size; texture, weathering, and strength of formation
material. If shown, designation in parentheses denotes Munsell
color classification.
TYPICAL MATERIAL GRAPHIC SYMBOLS

Fill Weathered Igneous Rock Poorly-graded SAND (SP) SILT (ML)

Lean CLAY (CL) Silty SAND (SM) with

gravel

TYPICAL SAMPLER GRAPHIC SYMBOLS OTHER GRAPHIC SYMBOLS

Grab sample from First water encountered at time of drilling and
cuttings sampling (ATD)
Static water level measured in boring or well at
Report: GEO_10_SNA_KEY; File: 60543652.GPJ; 5/31/2017 key

specified time after drilling

Change in material properties within a lithologic
stratum
Inferred contact between strata or gradational change
in lithology

GENERAL NOTES
1. Soil classifications are based on the Unified Soil Classification System. Descriptions and stratum lines are
interpretive; actual lithologic changes may be gradual. Field descriptions may have been modified to reflect results of
lab tests.
2. Descriptions on these logs apply only at the specific boring locations and at the time the borings were advanced.
They are not warranted to be representative of subsurface conditions at other locations or times.

Page 87
 Project: Fallbrook, COMM Tower
Log of Boring HA-1
Project Location: Fallbrook, CA
Project Number: 60543652 Sheet 1 of 1

Date(s) Logged Checked

Drilled 05/05/2017 By P. Kumar By M. Hatch
Drilling Drill Bit Total Depth
Method Hand Auger Size/Type 4" Auger of Borehole 4.3 feet
Drill Rig Drilling Approximate
Type N/A Contractor N/A Surface Elevation 1947 ft
Water Level Sampling Hammer
Depth N/A Method(s) Grab Sample Data N/A
Borehole
Completion Cuttings Location See Site Plan

SAMPLES

Dry Density, pcf

Graphic Log
Elevation,

Content, %
Blows per

MATERIAL DESCRIPTION REMARKS AND

Depth,

Number

OTHER TESTS
feet

feet

Water
Type

foot

0
Fill
Moist, brown, silty SAND with little gravel

1945

1 Residual Soil
2 Moist, reddish brown, silty SAND (SM) with gravel
Completely Weathered Rock
5 Fragments to: Moist, light yellowish brown, silty SAND with gravel
Bottom of boring at 4.25 feet below ground surface

1940

10

1935

15

1930

20
Report: GEO_10_SNA; File: 60543652.GPJ; 5/31/2017 HA-1

1925

25

1920

30

Page 88
 Project: Fallbrook, COMM Tower
Log of Boring HA-2
Project Location: Fallbrook, CA
Project Number: 60543652 Sheet 1 of 1

Date(s) Logged Checked

Drilled 05/05/2017 By P. Kumar By M. Hatch
Drilling Drill Bit Total Depth
Method Hand Auger Size/Type 4" Auger of Borehole 2.5 feet
Drill Rig Drilling Approximate
Type N/A Contractor N/A Surface Elevation 1947 ft
Water Level Sampling Hammer
Depth N/A Method(s) Grab Sample Data N/A
Borehole
Completion Cuttings Location See Site Plan

SAMPLES

Dry Density, pcf

Graphic Log
Elevation,

Content, %
Blows per

MATERIAL DESCRIPTION REMARKS AND

Depth,

Number

OTHER TESTS
feet

feet

Water
Type

foot

0
Fill
Moist, brown, silty SAND with little gravel

1945
Bottom of boring at 2.5 feet below ground surface. Refusal on 2" to 3" rock.

1940

10

1935

15

1930

20
Report: GEO_10_SNA; File: 60543652.GPJ; 5/31/2017 HA-2

1925

25

1920

30

Page 89
 Project: Fallbrook, COMM Tower
Log of Boring HA-3
Project Location: Fallbrook, CA
Project Number: 60543652 Sheet 1 of 1

Date(s) Logged Checked

Drilled 05/05/2017 By P. Kumar By M. Hatch
Drilling Drill Bit Total Depth
Method Hand Auger Size/Type 4" Auger of Borehole 3.8 feet
Drill Rig Drilling Approximate
Type N/A Contractor N/A Surface Elevation 1947 ft
Water Level Sampling Hammer
Depth N/A Method(s) Grab Sample Data N/A
Borehole
Completion Cuttings Location See Site Plan

SAMPLES

Dry Density, pcf

Graphic Log
Elevation,

Content, %
Blows per

MATERIAL DESCRIPTION REMARKS AND

Depth,

Number

OTHER TESTS
feet

feet

Water
Type

foot

0
Fill
Moist, brown, silty SAND with gravel

1945

Residual Soil
Moist, reddish brown, silty SAND (SM) with gravel
5 Bottom of boring at 3.8 feet below ground surface

1940

10

1935

15

1930

20
Report: GEO_10_SNA; File: 60543652.GPJ; 5/31/2017 HA-3

1925

25

1920

30

Page 90