Scribd
Upload
269 views5 pages

To Be Filled Out by The Processing Officer: Tesda-Op-QSO-02-F07 Rev. No. 00-03/01/17

This document contains a self-assessment guide to evaluate skills in assembling and servicing electronic products. It consists of three competency units - assembling electronic products, servicing consumer electronics, and servicing industrial electronics. For each unit, it lists key tasks and asks the candidate to check "yes" or "no" to indicate if they can perform each task. The candidate agrees for the assessment to be used for professional development and accessed only by authorized personnel.

Uploaded by

Ernesto Ogario
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
269 views5 pages

To Be Filled Out by The Processing Officer: Tesda-Op-QSO-02-F07 Rev. No. 00-03/01/17

This document contains a self-assessment guide to evaluate skills in assembling and servicing electronic products. It consists of three competency units - assembling electronic products, servicing consumer electronics, and servicing industrial electronics. For each unit, it lists key tasks and asks the candidate to check "yes" or "no" to indicate if they can perform each task. The candidate agrees for the assessment to be used for professional development and accessed only by authorized personnel.

Uploaded by

Ernesto Ogario
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

TESDA-OP-

QSO-02-F07
Rev. No. 00-03/01/17

Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0


to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING NC II

COC 1 Title ASSEMBLE ELECTRONICS PRODUCTS


Instruction
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.
Can I? YES NO
 Obtain and clarify work instructions
 Identify, prepare and obtain parts and components needed
 Prepare and check required materials, tools and equipment
 Prepare electronic components for assembly*
 Verify PCB layout in conformity with the schematic diagram
 Prepare/Make printed circuit board modules *
 Clean PCB based on standard procedures
 Test and visually inspect the functionality of the PCB
 Mount and solder electronic components *
 Apply soldering/de-soldering techniques and procedures
 Check soldered products
 Assemble electronic components *
 Integrate modules and accessories
 Perform assembly procedures of electronic products
 Test and inspect assembled electronic products *
 Subject finished products to final visual/sensory inspection
and testing
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name &Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 1
TESDA-OP-QSO-02-F07
Rev. No. 00-03/01/17
Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0
to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING
SERVICE CONSUMER ELECTRONICS PRODUCTS AND
COC 2 Title
SYSTEMS
Instruction
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.
Can I? YES NO
 Prepare the unit and required materials, tools equipment and
workplace properly for installation and service *
 Acquire manuals and service information required for installation
 Verify repair/maintenance history
 Conduct complete check-up of consumer electronic products and
systems, and identifies, verifies and documents defects against
customer description
 Test devices in accordance with standard procedures
 Install consumer electronic products and systems*
 Undertake final inspection
 Respond to unplanned events or conditions
 Clean and clear work site of all debris
 Prepare report on installation and testing of equipment
 Identify system defects/faults using appropriate tools and
equipment
 Diagnose faults and defects *
 Check and isolate circuits
 Explain identified defects and faults
 Check control settings/adjustments
 Document accurately results of diagnosis and testing
 Advise/inform customers regarding the status and serviceability
of the unit
 Replace defective parts/components with identical or recommended
appropriate equivalent ratings
 Maintain/Repair consumer electronic products *
 Use personal protective equipment
 Perform cleaning of unit

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 2
 Perform repair activity within the required timeframe
 Observe care and extreme precaution in handling the
unit/product
 Re-assemble and test repaired consumer electronic product *
 Subject reassembled units to final testing and cleaning
 Compile service completion procedures and
documentations
 Dispose waste materials
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name & Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 3
TESDA-OP-QSO-02-F07
Rev. No. 00-03/01/17
Reference No. EPA 1 9 0 9 8 3 1 3 4 0 0
to be filled out by the Processing Officer

SELF-ASSESSMENT GUIDE (PERFORMANCE ASSESSMENT)


ELECTRONICS PRODUCS ASSEMBLY AND
Qualification Title SERVICING NC II
SERVICE INDUSTRIAL ELECTRONIC MODULES,
COC 3 Title
PRODUCTS AND SYSTEMS
Instructions:
 Read each question in the left-hand column of the chart.
 Mark a check opposite each question to indicate your answer.

Can I? YES NO
 Prepare unit, tools and workplace for
installation/servicing*
 Acquire manuals and service information required for installation
 Verify repair/maintenance history
 Conduct complete check-up of consumer electronic products and
systems, and identifies, verifies and documents defects against
customer description
 Test devices
 Install industrial electronics systems/products *
 Undertake final inspection
 Respond to unplanned events or conditions
 Clean and clear work site of all debris
 Prepare report on installation and testing of equipment
 Identify system defects/faults using appropriate tools and equipment
 Test devices in accordance with standard procedures
 Diagnose faults of industrial electronics
systems/products*
 Check and isolate circuits
 Explain identified defects and faults
 Check control settings/adjustments
 Document accurately results of diagnosis and testing
 Advise/inform customers regarding the status and serviceability of
the unit
 Replace defective parts/components with identical or recommended
appropriate equivalent ratings
 Maintain/Repair industrial electronics products *
 Use personal protective equipment

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 4
 Perform cleaning of unit
 Perform repair activity within the required timeframe
 Observe care and extreme precaution in handling the unit/product
 Re-assemble and test repaired industrial electronics products *
 Subject reassembled units to final testing and cleaning
 Compile service completion procedures and documentations
 Dispose waste materials
 Apply safety rules and procedures *

I agree to undertake assessment in the knowledge that information


gathered will only be used for professional development purposes and
can only be accessed by concerned assessment personnel and
manager/supervisor.

Date:
Candidate’s Name &Signature:

ELCEAS 213-0614
Electronic Products Assembly and Servicing NC II 5

You might also like