KA3882/3/4/5 SMPS CONTROLLER

CURRENT MODE PWM CONTROLLER

8 DIP
The KA3882/3/4/5 are fixed PWM controller for Off-Line and DC
to DC converter applications. The internal circuits include UVLO,
low start up current circuit, temperature compensated reference,
high gain error amplifier, current sensing comparator, and high
current totempole output for driving a POWER MOSFET. Also KA
3882/3/4/5 provide low start up current below 0.3mA and short
shutdown delay time typ. 100ns.
The KA3882 and KA3884 have UVLO threshold of 1 6V(on) and 8 SOP
10V(off).
The KA3883 and KA3885 are 8.4V(on) and 7.6V(off).
The KA3882 and KA3883 can operate within 100% duty cycle.
The KA3884 and KA3885 within 50% by using T Flip-Flop.

FEATURES
• Low Start Current 0.2mA (typ)
• Operating Range Up To 500KHz
• Cycle by Cycle Current Limiting ORDERING INFORMATION
• Under Voltage Lock Out With Hysteresis
• Short Shutdown Delay Time: typ.100ns Device Package Operating Temperature
• High Current Totempole Output KA388X 8 DIP Î
0 ~ + 85
• Output Swing Limiting: 22V
KA388XD 8 SOP Î
0 ~ + 85

BLOCK DIAGRAM

Rev. B

©1999 Fairchild Semiconductor Corporation

KA3882/3/4/5 SMPS CONTROLLER

ABSOLUTE MAXIMUM RATINGS

Characteristic Symbol Value Unit

Supply Voltage VCC 30 V
Output Current IO +1 A
Analog Inputs (pin 2, 3) VI(ANA) - 0.3 to 6.3 V
Error Amp. Output Sink Current ISINK(EA) 10 mA
Power Dissipation PD 1 W

ELECTRICAL CHARACTERISTICS
(VCC = 15V, RT = 10K `, C T Îto + 85Î, Unless otherwise specified)
= 3.3nF, T A = 0

Characteristic Symbol Test Conditions Min Typ Max Unit

REFERENCE SECTION
Output Voltage VREF Î, I
T J = 25 O = 1mA 4.9 5.0 5.1 V
Line Regulation LV REF VCC = 12V to 25V ï 6 20 mV
Load Regulation LV REF IO = 1mA to 20mA ï 6 25 mV
Output Short Circuit ISC Î
T a = 25 ï - 100 - 180 mA
OSILLATOR SECTION
Initial Accuracy FOSC Î
T J = 25 47 52 57 KHz
Voltage Stability ST V VCC = 12V to 25V ï 0.2 1 %
Amplitude VOSC VPIN4, Peak to Peak ï 1.7 ï V
Discharge Current IDISCHG Î, Pin4 = 2V
T J = 25 7.8 8.3 8.8 mA
CURRENT SENSE SECTION
Gain GV (NOTE 2, 3) 2.85 3 3.15 V/V
Maximum Input Signal VI(MAX) VPIN1 = 5V(NOTE 2) 0.9 1.0 1.1 V

PSRR PSRR
VCC = 12V to 25V
(NOTE 1, 2)
ï 70 ï dB

Input Bias Current IBIAS ï ï -2 -10 uA

Delay to Output TD VPIN3 = 0V to 2V (NOTE1) ï 100 200 ns
KA3882/3/4/5 SMPS CONTROLLER

ELECTRICAL CHARACTERISTICS(Continued)
(VCC = 15V, RT = 10K `, C T Îto + 85Î, Unless otherwise specified)
= 3.3nF, T A = 0

Characteristic Symbol Test Conditions Min Typ Max Unit

ERROR AMPLIFIER SECTION
Input Voltage VI T PIN1 = 2.5V 2.42 2.50 2.58 V
Input Bias Current IBIAS ï ï -0.3 -2 uA

Open Loop Gain GVO

VO = 2V to 4V
(NOTE 1)
65 90 ï dB

Unity Gain Bandwidth GBW

T J= 25Î 0.7 1 ï MHz
(NOTE 1)

PSRR PSRR
VCC = 12V to 25V
(NOTE 1)
60 70 ï dB

Output Sink Current ISINK

VPIN2 = 2.7V
VPIN1 = 1.1V
2 6 ï mA

Output Source Current ISOURCE

VPIN2 = 2.3V
VPIN1 = 5.0V
-0.5 -0.8 ï mA

Output High Voltage VOH

VPIN2 = 2.3V
R1 = 15K ` to GND 5 6 ï V

Output Low Voltage VOL

VPIN2 = 2.7V
R1 = 15K ` to Pin8 ï 0.8 1.1 V

OUTPUT SECTION
ISINK = 20mA ï 0.1 0.4 V
Output Low Level VOL
ISINK = 200mA ï 1.5 2.2 V
ISOURCE = 20mA 13 13.5 ï V
Output High Level VOH
ISOURCE = 200mA 12 13.5 ï V

Rise Time tR
T J = 25 Î, C1 = 1nF ï 40 100 ns
(NOTE 1)

Fall Time tF
T J = 25 Î, C1 = 1nF ï 40 100 ns
(NOTE 1)
Output Voltage Swing Limit VOLIM VCC = 27V, C1 = 1nF ï 22 ï V
UNDER VOLTAGE LOCKOUT SECTION
KA3882/4 15 16 17 V
Start Threshold VTH
KA3883/5 7.8 8.4 9.0 V
Min.Operating Voltage KA3882/4 9 10 11 V
VTL
( After turn on ) KA3883/5 7.0 7.6 8.2 V
KA3882/3/4/5 SMPS CONTROLLER

ELECTRICAL CHARACTERISTICS(Continued)
(VCC = 15V, RT = 10K `, C T Îto +85Î, unless otherwise specified)
= 3.3nF, T A = 0

Characteristic Symbol Test Conditions Min Typ Max Unit

PWM SECTION
KA3882/3 94 96 100 %
Maximum Duty Cycle DMAX
KA3884/5 47 48 50 %
Minimum Duty Cycle DMIN ï ï ï 0 %
TOTAL STANDBY CURRENT
Start-Up Current IST ï ï 0.2 0.4 mA
Operating Supply Current ICC VPIN2 = VPIN3 = 0V ï 11 17 mA
VCC Zener Voltage VZ ICC = 25mA ï 29 ï V

Adjust VCC above the start threshold bifore setting at 15V

NOTE 1. These parameters, although guaranteed, are not 100% tested in production.
2. Parameter measured at trip point of latch with V2 = 0V.
3. Gain defined as: GV = L L
VPIN1 VPIN3(VPIN3 = 0 to 0.8V)
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.

ACEx™ ISOPLANAR™ UHC™

CoolFET™ MICROWIRE™ VCX™
CROSSVOLT™ POP™
E2CMOSTM PowerTrench™
FACT™ QS™
FACT Quiet Series™ Quiet Series™
FAST® SuperSOT™-3
FASTr™ SuperSOT™-6
GTO™ SuperSOT™-8
HiSeC™ TinyLogic™

DISCLAIMER

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER

NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant into support device or system whose failure to perform can
the body, or (b) support or sustain life, or (c) whose be reasonably expected to cause the failure of the life
failure to perform when properly used in accordance support device or system, or to affect its safety or
with instructions for use provided in the labeling, can be effectiveness.
reasonably expected to result in significant injury to the
user.

PRODUCT STATUS DEFINITIONS

Definition of Terms

Datasheet Identification Product Status Definition

Advance Information Formative or This datasheet contains the design specifications for
In Design product development. Specifications may change in
any manner without notice.

Preliminary First Production This datasheet contains preliminary data, and

supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.

No Identification Needed Full Production This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.

Obsolete Not In Production This datasheet contains specifications on a product

that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
This datasheet has been downloaded from:

www.DatasheetCatalog.com

Datasheets for electronic components.