TR 45/250 Single Skin Roof & Wall Profile

Technical Data Sheet Page 1 of 5

Tigerprofiles TR 45/250 trapezoidal profile is applicable in its usage for single skin (non-insulated)
roof and wall applications.
Material and Product Specifications

Usage Roofing & Cladding

TR 45/250
Aluminum: 03.5—1.2mm
Material
& Post-Production Alu-zinc: 03.5—1.2mm
Thickness
Galvanized Iron: 0.30 to 0.90mm

Covering Width: 1,000 mm

Crown: 30mm
Valley: 140mm
Dimensions (mm) Profile Pitch: 250mm

Profile Depth: 45mm

Rib Width: 110mm

Standard RAL Colors.

Special colors on request
Colors
Minimum order applies

Pre-painted Polyester
Pre-painted PVDF
Coating/Finish
Mill-Finish

Curved eave TR 45/250

PB Ridge
Flashing ing
a sh
Gutters e fl
ad
GI Self-tapping screws with neoprene -m
m
sto
SS Self-drilling screws with neoprene Cu

Accessories Butyle Sealant tape

Purlin Tape
PVC Tape
PVC Color Caps
Aluminum Rivets
r
Bulb-tite Rivets tte
Gu
Filler Blocks Silicon Sealant
Rev 03 15-Feb-15

T: +971 6 533 8449

F: +971 6 533 6673
E: [email protected]

The Roof & Cladding Company Website: Tigerprofiles.com

Information contained here was, at the time of publishing, accurate and true to the best of our knowledge, but isn’t intended to replace engineering judgment—for support
please contact our Sales Dept. We reserve the right to make any changes for continuous improvement .
 TR 45/250 Single Skin Roof & Wall Profile
Technical Data Sheet Page 2 of 5
Section Properties (per meter width) Base metal: steel
Elastic
Nominal Cover Nominal Top in Compression Bottom in Compression
Area Full Sect. Modulus
Thickness Width Weight
(cm2) Ix (cm4) ( E )(kN/ Sx-Top Sx-Bot Ma bx Ixeb Sx-Top Sx-Bot Ma bx
(T) (mm) (mm) (kg/m2) Ixet (cm4)
cm2) (cm3) (cm3) (kNm) (cm4) (cm3) (cm3) (kNm)
0.40 1000 3.83 4.84 14.66 20300 11.20 3.40 9.03 0.46 10.82 4.45 5.12 0.60

0.50 1000 4.79 6.05 18.32 20300 15.66 4.95 11.28 0.67 14.18 5.65 6.95 0.77

0.60 1000 5.75 7.26 21.99 20300 20.54 6.74 13.58 0.92 17.63 6.86 8.86 0.93
0.70 1000 6.70 8.47 25.65 20300 24.85 8.52 15.92 1.12 21.21 8.08 10.91 1.10

0.80 1000 7.66 9.68 29.31 20300 28.69 9.55 18.19 1.30 24.90 9.30 13.08 1.27

0.90 1000 8.62 10.88 32.97 20300 32.56 10.86 20.45 1.48 28.70 10.54 15.37 1.44

1.00 1000 9.58 12.09 36.63 20300 36.39 12.14 22.68 1.65 32.57 11.77 17.76 1.60
1.20 1000 11.49 14.51 43.96 20300 43.85 14.61 27.10 1.99 40.56 14.26 22.83 1.94

Notes:  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa

 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design)
 Nominal Thickness refers to Base Metal Thickness

Steel: Permissible Span (mm)

Nominal Span (m)
No. of
Thickness (T) Load Case
Spans
(mm) 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
0.40 1 *D + L 3.68 2.36 1.64 1.20 0.92 0.73 0.59 0.49 0.41

0.40 1 **WS 4.80 3.07 2.13 1.57 1.20 0.95 0.77 0.61 0.47

0.40 2 D+L 4.00 2.71 1.95 1.47 1.14 0.91 0.74 0.62 0.52

0.40 2 WS 3.28 2.18 1.55 1.15 0.89 0.71 0.58 0.48 0.40

0.40 3 D+L 4.69 3.24 2.35 1.78 1.39 1.12 0.91 0.76 0.64

0.40 3 WS 3.92 2.64 1.89 1.42 1.10 0.88 0.71 0.59 0.50

0.50 1 D+L 5.36 3.43 2.38 1.75 1.34 1.06 0.86 0.71 0.59

0.50 1 WS 6.16 3.94 2.74 2.01 1.54 1.22 0.99 0.76 0.59

0.50 2 D+L 5.64 3.72 2.63 1.95 1.50 1.19 0.97 0.80 0.68

0.50 2 WS 5.01 3.28 2.31 1.71 1.32 1.04 0.85 0.70 0.59

0.50 3 D+L 6.82 4.54 3.23 2.41 1.86 1.48 1.21 1.00 0.84

0.50 3 WS 6.10 4.03 2.85 2.12 1.63 1.30 1.05 0.87 0.74

0.60 1 D+L 7.36 4.71 3.27 2.40 1.84 1.45 1.18 0.92 0.71

0.60 1 WS 7.44 4.76 3.31 2.43 1.86 1.47 1.19 0.92 0.71

0.60 2 D+L 7.06 4.60 3.23 2.39 1.83 1.45 1.18 0.98 0.82

0.60 2 WS 6.99 4.55 3.19 2.36 1.82 1.44 1.17 0.97 0.81

0.60 3 D+L 8.63 5.67 3.99 2.96 2.28 1.81 1.47 1.22 1.02

0.60 3 WS 8.55 5.61 3.95 2.93 2.26 1.79 1.45 1.20 1.01
Notes:  Deflection Limits - Span / 180; for deflection Span/240, value divide by
 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design) 1.33
 D+L - Dead + Live Load WS- Wind Suction  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa
 Nominal Thickness refers to Base Metal Thickness
Rev 03 15-Feb-15

T: +971 6 533 8449

F: +971 6 533 6673
E: [email protected]

The Roof & Cladding Company Website: Tigerprofiles.com

Information contained here was, at the time of publishing, accurate and true to the best of our knowledge, but isn’t intended to replace engineering judgment—for support
please contact our Sales Dept. We reserve the right to make any changes for continuous improvement .
 TR 45/250 Single Skin Roof & Wall Profile
Technical Data Sheet Page 3 of 5

Steel: Permissible Span (mm)

Nominal Span (m)
No. of
Thickness (T) Load Case
Spans
(mm) 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
0.70 1 D+L 8.96 5.73 3.98 2.93 2.24 1.77 1.42 1.07 0.82

0.70 1 WS 8.80 5.63 3.91 2.87 2.20 1.74 1.41 1.07 0.82

0.70 2 D+L 8.45 5.49 3.84 2.83 2.18 1.72 1.40 1.16 0.97

0.70 2 WS 8.59 5.58 3.91 2.88 2.22 1.75 1.42 1.18 0.99

0.70 3 D+L 10.39 6.78 4.76 3.52 2.71 2.15 1.74 1.44 1.21

0.70 3 WS 10.56 6.90 4.84 3.58 2.76 2.19 1.77 1.47 1.24

0.80 1 D+L 10.40 6.66 4.62 3.40 2.60 2.05 1.62 1.22 0.94

0.80 1 WS 10.16 6.50 4.52 3.32 2.54 2.01 1.62 1.22 0.94

0.80 2 D+L 9.83 6.37 4.45 3.28 2.52 1.99 1.62 1.34 1.12

0.80 2 WS 10.05 6.51 4.55 3.36 2.58 2.04 1.65 1.37 1.15

0.80 3 D+L 12.12 7.88 5.53 4.08 3.14 2.48 2.02 1.67 1.40

0.80 3 WS 12.38 8.06 5.65 4.18 3.21 2.54 2.06 1.71 1.44

0.90 1 D+L 11.84 7.58 5.26 3.87 2.96 2.34 1.83 1.37 1.06

0.90 1 WS 11.52 7.37 5.12 3.76 2.88 2.28 1.83 1.37 1.06

0.90 2 D+L 11.14 7.21 5.04 3.72 2.86 2.26 1.83 1.52 1.28

0.90 2 WS 11.43 7.41 5.18 3.82 2.93 2.32 1.88 1.56 1.31

0.90 3 D+L 13.73 8.93 6.26 4.63 3.56 2.82 2.29 1.89 1.59

0.90 3 WS 14.08 9.17 6.43 4.75 3.65 2.89 2.35 1.94 1.63

1.00 1 D+L 13.20 8.45 5.87 4.31 3.30 2.61 2.03 1.53 1.18

1.00 1 WS 12.80 8.19 5.69 4.18 3.20 2.53 2.03 1.53 1.18

1.00 2 D+L 12.38 8.02 5.60 4.13 3.17 2.51 2.04 1.68 1.42

1.00 2 WS 12.74 8.25 5.77 4.26 3.27 2.59 2.10 1.74 1.46

1.00 3 D+L 15.25 9.93 6.96 5.14 3.95 3.13 2.54 2.10 1.77

1.00 3 WS 15.69 10.22 7.17 5.30 4.07 3.23 2.62 2.17 1.82

1.20 1 D+L 15.92 10.19 7.08 5.20 3.98 3.14 2.44 1.83 1.41

1.20 1 WS 15.52 9.93 6.90 5.07 3.88 3.07 2.44 1.83 1.41

1.20 2 D+L 14.99 9.71 6.79 5.01 3.85 3.04 2.47 2.04 1.72

1.20 2 WS 15.35 9.95 6.96 5.14 3.94 3.12 2.53 2.09 1.76

1.20 3 D+L 18.47 12.03 8.43 6.23 4.79 3.79 3.08 2.55 2.14

1.20 3 WS 18.90 12.32 8.64 6.39 4.91 3.89 3.16 2.61 2.20

Notes:  Deflection Limits - Span / 180; for deflection Span/240, value divide by
 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design) 1.33
 D+L - Dead + Live Load WS- Wind Suction  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa
 Nominal Thickness refers to Base Metal Thickness
Rev 03 15-Feb-15

T: +971 6 533 8449

F: +971 6 533 6673
E: [email protected]

The Roof & Cladding Company Website: Tigerprofiles.com

Information contained here was, at the time of publishing, accurate and true to the best of our knowledge, but isn’t intended to replace engineering judgment—for support
please contact our Sales Dept. We reserve the right to make any changes for continuous improvement .
 TR 45/250 Single Skin Roof & Wall Profile
Technical Data Sheet Page 4 of 5
Section Properties (per meter width) Base metal: aluminum
Elastic
Nominal Cover Nominal Top in Compression Bottom in Compression
Area Full Sect. Modulus
Thickness Width Weight
(cm2) Ix (cm4) ( E )(kN/ Sx-Top Sx-Bot Ma bx Ixeb Sx-Top Sx-Bot Ma bx
(T) (mm) (mm) (kg/m2) Ixet (cm4)
cm2) (cm3) (cm3) (kNm) (cm4) (cm3) (cm3) (kNm)
0.40 1000 1.33 4.84 14.66 6900 9.52 2.73 9.00 0.24 9.44 4.26 4.06 0.35

0.50 1000 1.67 6.05 18.32 6900 13.37 3.98 11.23 0.35 12.67 5.41 5.73 0.47

0.60 1000 2.00 7.26 21.99 6900 17.62 5.42 11.46 0.47 15.84 6.58 7.35 0.57

0.70 1000 2.33 8.47 25.65 6900 22.21 7.04 15.70 0.61 19.12 7.76 9.07 0.68

0.80 1000 2.66 9.68 29.31 6900 27.09 8.82 17.96 0.76 22.45 8.95 10.83 0.78

0.90 1000 3.00 10.88 32.97 6900 31.59 10.42 20.27 0.91 25.88 10.14 12.70 0.88

1.00 1000 3.33 12.09 36.63 6900 35.62 11.79 22.55 1.02 29.42 11.34 14.65 0.99

1.20 1000 4.00 14.51 43.96 6900 43.33 14.37 26.99 1.25 36.75 13.76 18.84 1.20

Notes:  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa

 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design)
 Nominal Thickness refers to Base Metal Thickness

aluminum: Permissible Span (mm)

Nominal Span (m)
No. of
Thickness (T) Load Case
Spans
(mm) 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
0.40 1 *D + L 1.92 1.23 0.85 0.63 0.48 0.38 0.28 0.21 0.16

0.40 1 **WS 2.80 1.79 1.24 0.81 0.54 0.38 0.28 0.21 0.16

0.40 2 D+L 1.84 1.32 0.99 0.77 0.61 0.49 0.41 0.34 0.29

0.40 2 WS 1.51 1.04 0.76 0.57 0.45 0.36 0.29 0.24 0.21

0.40 3 D+L 2.06 1.51 1.15 0.90 0.72 0.59 0.48 0.39 0.30

0.40 3 WS 1.75 1.23 0.90 0.69 0.54 0.44 0.34 0.25 0.19

0.50 1 D+L 2.80 1.79 1.24 0.91 0.67 0.47 0.35 0.26 0.20

0.50 1 WS 3.76 2.41 1.60 1.01 0.67 0.47 0.35 0.26 0.20

0.50 2 D+L 2.96 2.04 1.48 1.12 0.87 0.70 0.57 0.48 0.40

0.50 2 WS 2.42 1.62 1.16 0.87 0.67 0.54 0.44 0.36 0.31

0.50 3 D+L 3.42 2.40 1.77 1.35 1.06 0.86 0.65 0.49 0.38

0.50 3 WS 2.86 1.95 1.41 1.06 0.83 0.62 0.45 0.34 0.26

0.60 1 D+L 3.76 2.41 1.67 1.21 0.81 0.57 0.41 0.31 0.24

0.60 1 WS 4.56 2.92 1.92 1.21 0.81 0.57 0.41 0.31 0.24

0.60 2 D+L 3.99 2.67 1.90 1.42 1.10 0.87 0.71 0.59 0.50

0.60 2 WS 3.42 2.26 1.60 1.19 0.92 0.73 0.59 0.49 0.41

0.60 3 D+L 4.75 3.22 2.32 1.74 1.35 1.07 0.78 0.59 0.45

0.60 3 WS 4.13 2.76 1.96 1.47 1.10 0.77 0.56 0.42 0.33
Notes:  Deflection Limits - Span / 180; for deflection Span/240, value divide by
 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design) 1.33
 D+L - Dead + Live Load WS- Wind Suction  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa
 Nominal Thickness refers to Base Metal Thickness
Rev 03 15-Feb-15

T: +971 6 533 8449

F: +971 6 533 6673
E: [email protected]

The Roof & Cladding Company Website: Tigerprofiles.com

Information contained here was, at the time of publishing, accurate and true to the best of our knowledge, but isn’t intended to replace engineering judgment—for support
please contact our Sales Dept. We reserve the right to make any changes for continuous improvement .
 TR 45/250 Single Skin Roof & Wall Profile
Technical Data Sheet Page 5 of 5

aluminum: Permissible Span (mm)

Nominal Span (m)
No. of
Thickness (T) Load Case
Spans
(mm) 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
0.70 1 D+L 4.88 3.12 2.17 1.41 0.94 0.66 0.48 0.36 0.28

0.70 1 WS 5.44 3.48 2.24 1.41 0.94 0.66 0.48 0.36 0.28

0.70 2 D+L 5.03 3.30 2.33 1.73 1.33 1.06 0.86 0.71 0.60

0.70 2 WS 4.57 2.99 2.11 1.56 1.20 0.95 0.77 0.64 0.50

0.70 3 D+L 6.09 4.04 2.87 2.14 1.65 1.25 0.91 0.69 0.53

0.70 3 WS 5.57 3.68 2.60 1.93 1.33 0.93 0.68 0.51 0.39

0.80 1 D+L 6.08 3.89 2.56 1.61 1.08 0.76 0.55 0.41 0.32

0.80 1 WS 6.24 3.99 2.56 1.61 1.08 0.76 0.55 0.41 0.32

0.80 2 D+L 5.91 3.85 2.71 2.00 1.54 1.22 0.99 0.82 0.69

0.80 2 WS 5.77 3.76 2.64 1.95 1.50 1.19 0.96 0.76 0.59

0.80 3 D+L 7.22 4.75 3.35 2.48 1.91 1.43 1.04 0.78 0.60

0.80 3 WS 7.06 4.64 3.27 2.33 1.56 1.09 0.80 0.60 0.46

0.90 1 D+L 7.28 4.66 2.88 1.81 1.21 0.85 0.62 0.47 0.36

0.90 1 WS 7.04 4.51 2.88 1.81 1.21 0.85 0.62 0.47 0.36

0.90 2 D+L 6.74 4.38 3.07 2.27 1.74 1.38 1.12 0.93 0.78

0.90 2 WS 6.95 4.52 3.17 2.34 1.80 1.42 1.16 0.88 0.68

0.90 3 D+L 8.27 5.41 3.80 2.81 2.16 1.61 1.17 0.88 0.68

0.90 3 WS 8.52 5.58 3.92 2.68 1.80 1.26 0.92 0.69 0.53

1.00 1 D+L 8.16 5.22 3.20 2.01 1.35 0.95 0.69 0.52 0.40

1.00 1 WS 7.92 5.07 3.20 2.01 1.35 0.95 0.69 0.52 0.40

1.00 2 D+L 7.64 4.95 3.46 2.55 1.96 1.55 1.26 1.04 0.88

1.00 2 WS 7.85 5.09 3.56 2.63 2.02 1.60 1.30 1.00 0.77

1.00 3 D+L 9.40 6.12 4.30 3.18 2.44 1.79 1.30 0.98 0.75

1.00 3 WS 9.65 6.30 4.42 3.05 2.04 1.43 1.05 0.79 0.61

1.20 1 D+L 10.00 6.40 3.83 2.41 1.62 1.14 0.83 0.62 0.48

1.20 1 WS 9.60 6.14 3.83 2.41 1.62 1.14 0.83 0.62 0.48

1.20 2 D+L 9.29 6.02 4.20 3.10 2.38 1.88 1.53 1.26 1.06

1.20 2 WS 9.65 6.26 4.37 3.23 2.48 1.96 1.59 1.25 0.96

1.20 3 D+L 11.46 7.45 5.22 3.86 2.96 2.14 1.56 1.17 0.90

1.20 3 WS 11.89 7.74 5.43 3.81 2.55 1.79 1.31 0.98 0.76
Notes:  Deflection Limits - Span / 180; for deflection Span/240, value divide by
 Design of sheeting is based on AISI -2007 (ASD-Allowable Stress Design) 1.33
 D+L - Dead + Live Load WS- Wind Suction  Material Specifications - ASTM A653 - Yield Strength - 230 Mpa
 Nominal Thickness refers to Base Metal Thickness
Rev 03 15-Feb-15

T: +971 6 533 8449

F: +971 6 533 6673
E: [email protected]

The Roof & Cladding Company Website: Tigerprofiles.com

Information contained here was, at the time of publishing, accurate and true to the best of our knowledge, but isn’t intended to replace engineering judgment—for support
please contact our Sales Dept. We reserve the right to make any changes for continuous improvement .