Scribd
Upload
201 views5 pages

LanTEK IV Software Update Procedure Rev3 en

The document provides instructions for updating the software on the LanTEK IV field tester. It involves 3 steps: 1) Downloading the update files from the manufacturer's website. 2) Updating the main handset by connecting a USB drive with the update files to the powered-on device. 3) Repeating the process to update any remote handsets connected to the main unit. The update process takes several minutes and involves watching for completion messages and LED indicators.

Uploaded by

Fabio Barros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
201 views5 pages

LanTEK IV Software Update Procedure Rev3 en

The document provides instructions for updating the software on the LanTEK IV field tester. It involves 3 steps: 1) Downloading the update files from the manufacturer's website. 2) Updating the main handset by connecting a USB drive with the update files to the powered-on device. 3) Repeating the process to update any remote handsets connected to the main unit. The update process takes several minutes and involves watching for completion messages and LED indicators.

Uploaded by

Fabio Barros
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

LanTEK IV

Field Software Update Procedure

Depend On Us 1
SYNC your LanTEK IV to AnyWARE Cloud before performing the update.
From the home screen, press then upload to AnyWARE Cloud from the
SYNC prompt.

1. Download the software:

Download the software from: www.trend-networks.com/support/downloads/

Format a USB stick of between 4 and 32GB on Windows PC (Fat32 format)

Extract the files from the ZIP to the ROOT of USB flash drive with >3GB free space.
These files should be on the ROOT (not inside a folder) of the USB flash drive.

The contents of the flash drive should be similar to this:

Extracted files

2 www.trend-networks.com
2. Update main handset:

• Power off LanTEK IV


• Disconnect any test adapters from the LanTEK IV
• Connect main handset to DC power adapter
• Connect USB flash drive to main handset
• Power on main handset and wait for the following screen:

USB

Power

• Press and hold the


button to start the update process.
Release the button when the percentage
indicator is shown on the screen
• This stage will take a few minutes to
complete
• During this stage the screen will show the
update progress (right):

Depend On Us 3
When complete, it will show this message:

USB

• Press and hold the power button for 15


seconds
• Release the power button to shut
down the handset
• Remove the flash drive

Power

• Press the power button to restart the


handset and complete the update procedure.
After a few seconds LEDs at the top of the
display (Partner & Hazard) will flash Green /
Red indicating update is continuing and the
following screen will be shown (right)

• This will take several minutes, after which the


update is complete and the main handset is
ready for use

4 www.trend-networks.com
3. Update remote handset:

• Power the remote handset OFF


• Disconnect any test adapters from the LanTEK IV
• Connect DC power adapter to the remote handset
• Connect the USB flash drive to the remote handset
• Power on the remote handset then after a few seconds Tone and Talk LEDs will
alternately flash green, then just the tone LED will remain steady green:

USB

• Press and hold the button to start the


update process. This stage will take a few
minutes to complete
• During this stage the Tone and Talk LEDs
will flash green
Power
• When the first stage of the update is
complete, the Pass LED will remain steady
green:

• Press and hold the power button for 15


seconds
• Release the power button to shut down
the handset
• Remove the USB flash drive
• Press power button to turn on the
handset to continue the update
• The Tone and Talk LEDs will flash red/
green during this process:

• This will take several minutes, after which the


Tone Talk LEDs will stop flashing indicating
the Remote handset is ready for use

Depend On Us 5

You might also like