Scribd
Upload
517 views2 pages

Drive Fault Codes: LED Display Message Fault Code Explanation

This document lists and explains fault codes that may appear on the LED display of a drive. There are 82 possible fault codes ranging from "NErr" indicating no error to more serious faults like "OCr" for overcurrent in the dynamic braking resistor. The codes are grouped into categories identifying the type of fault such as overcurrent, overvoltage, communication errors, and input/output issues. Each code is accompanied by a brief explanation of the fault it represents.

Uploaded by

Felipe Perez Dos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
517 views2 pages

Drive Fault Codes: LED Display Message Fault Code Explanation

This document lists and explains fault codes that may appear on the LED display of a drive. There are 82 possible fault codes ranging from "NErr" indicating no error to more serious faults like "OCr" for overcurrent in the dynamic braking resistor. The codes are grouped into categories identifying the type of fault such as overcurrent, overvoltage, communication errors, and input/output issues. Each code is accompanied by a brief explanation of the fault it represents.

Uploaded by

Felipe Perez Dos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

9.

Drive Fault Codes

LED Display
Fault Code Explanation
Message

NErr No error has been recorded since the last


0
drive reset or trip clear
OC1 1 Overcurrent during acceleration
OC2 2 Overcurrent during deceleration
OC3 3 Overcurrent during constant-speed run
OCL Load-end overcurrent detected at start-up
4
(output terminals, motor wiring etc.)
OCA1 5 U-phase IGBT short circuit
OCA2 6 V-phase IGBT short circuit
OCA3 7 W-phase IGBT short circuit
EPHI 8 Lost input phase (option)
EPHO 9 Lost output phase (option)
OP1 10 Overvoltage during acceleration
OP2 11 Overvoltage during deceleration
OP3 12 Overvoltage during constant-speed run
OLIn 13 Drive overload
OLMt 14 Motor overload
Olr 15 Dynamic braking resistor overload
OH 16 Drive overheat
E 17 Emergency off
EEP1 18 EEPROM failure during write
EEP2 19 EEPROM failure during initial read
 20 Unused
Err2 21 RAM error
Err3 22 ROM error
Err4 23 CPU error
Err5 24 RS232C timer time-out
Err6 25 Gate array error
Err7 26 Output current detection circuit error
Communication interface card error
Err8 27
(check that parameterIno in Gr.tr is not 0)
Err9 28 Option ROM error / option ROM not detected
UC 29 Low current
UP1 30 Main circuit undervoltage
 31 Unused
Ot 32 Overtorque
EF1 33 Earth fault (software)
EF2 34 Earth fault (hardware)
EFU 35 Open fuse
LED Display
Fault Code Explanation
Message
OCr 36 Dynamic braking resistor overcurrent
OC1P 37 Overcurrent in DC section during acceleration
OC2P 38 Overcurrent in DC section during deceleration
OC3P Overcurrent in DC section during constant-
39
speed run
EtN 40 Auto-tuning error
EtyP 41 Drive typeform error
 42 ∼ 80 Unused
dAMP 81 Closed damper detected
LOSS 82 Loss of IV input detected

You might also like