D Error codes - 1 Engine 9

1 Engine
Error codes engine, descrition
For contact with engine suppliers, use Volvo/Cummins code.

Display indicates error code acc. to SAE J1939

SPN / FMI
Flash indicates error code according to engine supplier specified
flash code.
J1587 indicates error code acc. to SAE J1587 (for Volvo: Vodia).

PID, PPID, SID, PSID / FMI

FMI descriptions

FMI Description SAE-text

0 Too high value. Data valid, but higher than normal operating range.

1 Too low value. Data valid, but lower than normal operating range.

2 Incorrect data. Intermittent or incorrect data.

3 Electrical problem. Abnormally high voltage or short-circuit to higher voltage.

4 Electrical problem. Abnormally low voltage or short-circuit to lower voltage.

5 Electrical problem. Abnormally low current or open circuit.

6 Electrical problem. Abnormally high current or short-circuit to ground.

7 Mechanical problem. Incorrect response from mechanical system.

8 Mechanical problem or electrical problem. Abnormal frequency.

9 Communication error. Abnormal update rate.

10 Mechanical problem or electrical problem. Abnormally wide variations.

11 Unknown malfunction. Non-identifiable malfunction.

12 Component error. Incorrect unit or component.

13 Incorrect calibration. Values outside calibration values.

14 Unknown malfunction. Special instructions.

15 Unknown malfunction. Reserved for future use.

Error codes and Wiring diagrams from Workshopmanual DRF 400- DDRF01.01 GB

450 (VDRF03.01 GB) DRF 400-450

10 D Error codes - 1 Engine

Error codes engine (engine

alternative Volvo)

Display
0
Flash J1587
Description Action

94/FMI 3.6 PID94/FMI Fuel pressure. STOP

94/FMI 3.8 PID94/FMI Fuel pressure. STOP

97/1 2.1 PID97/1 Water in fuel. WARNING: Drain fuel pre-fil-

ter.

97/3 2.9 PID97/3 Water in fuel or clogged fuel line (low fuel pressure). WARNING: Drain fuel pre-fil-
ter.

98/FMI 5.7 PID98/FMI Oil level. STOP: Check oil level in en-
gine.

98/FMI 5.9 PID98/FMI Oil level. STOP: Check oil level in en-
gine.

100/1 6.6 PID100/1 Low engine oil pressure. Engine is shut off. STOP: Check oil level in en-
gine.

100/3 3.1 PID100/3 Sensor oil pressure cable short-circuited to voltage. STOP

100/4 3.1 PID100/4 Sensor oil pressure, open circuit or short-circuit to STOP
ground.

102/0 3.5 PID102/0 High charge-air pressure. STOP

102/1 3.5 PID102/1 Low boost pressure. Reduced engine power. STOP

102/3 3.4 PID102/3 Sensor boost pressure, cable short-circuited to volt- STOP
age. Engine smokes more than normal at accelera-
tion/load.

102/4 3.4 PID102/4 Sensor boost pressure, cable short-circuited ground STOP
or open circuit. Engine smokes more than normal at
acceleration/load.

105/3 3.2 PID105/3 Sensor charge-air temperature, cable short- STOP

circuited to voltage or open circuit.

105/4 3.3 PID105/4 Sensor charge-air temperature, cable short- STOP

circuited to ground or open circuit.

105/FMI 6.2 PID105/FMI Charge-air temperature. STOP

106/FMI 3.4 PID106/FMI Boost pressure. STOP

106/FMI 3.5 PID106/FMI Boost pressure. STOP

110/0 6.1 PID110/0 High coolant temperature. For engine alternative STOP: Check coolant level.
TWD1240VE: engine shuts down.

DDRF01.01GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450
 D Error codes - 1 Engine 11

Display
0
Flash J1587
Description Action

110/3 3.3 PID110/3 Sensor coolant temperature, cable short-circuited to STOP

voltage or open circuit. Preheating is activated even
if engine is warm.

110/4 3.3 PID110/4 Sensor coolant temperature, cable short-circuited to STOP

ground. Preheating is activated even if engine is
warm.

111/1 2.2 PID111/1 Low coolant level. For engine alternative STOP: Check coolant level.
TWD1240VE: engine shuts down.

111/FMI 2.3 PID111/FMI Coolant level. STOP

158/FMI 3.9 PID158/FMI Battery voltage. STOP

175/0 5.8 PID175/0 High engine oil temperature. Reduced engine pow- STOP
er.

175/3 3.7 PID175/3 Sensor oil temperature, cable short-circuited to volt- STOP
age or open circuit.

175/4 3.7 PID175/4 Sensor oil temperature, cable short-circuited to STOP

ground.

608/FMI - PPID98/FMI Start / stop, redundance. STOP

608/FMI 2.8 PPID132/ Signal from accelerator pedal, redundance. STOP

FMI

620/3 9.3 SID232/3 Voltage feed to sensor, cable short-circuited to volt- STOP
age. Several error codes for sensor malfunction.

620/4 9.3 SID232/4 Voltage feed to sensor, cable short-circuited to STOP

ground. Several error codes for sensor malfunction.

626/3 5.4 PID45/3 Preheating relay, cable short-circuited to voltage. STOP

Preheating cannot be activated.

626/4 5.4 PID45/4 Preheating relay, cable short-circuited to ground. STOP

Preheating constantly activated.

626/5 5.4 PID45/5 Preheating relay open circuit on cable or defective STOP
component. Preheating cannot be activated.

629/FMI 9.9 SID254/FMI Internal error, engine control unit. STOP

Engine off: engine cannot be started. Engine run-

ning: engine misfires.

630/2 9.9 SID253/2 Electrical problem. Reduced engine power. STOP

630/12 9.9 SID253/12 Electrical problem. Reduced engine power. STOP

636/3 2.5 SID21/3 Sensor rpm camshaft. No signal. Engine takes long- STOP
er to start than normal. Engine runs normally once it
has started.

Error codes and Wiring diagrams from Workshopmanual DRF 400- DDRF01.01 GB

450 (VDRF03.01 GB) DRF 400-450

12 D Error codes - 1 Engine

Display
0
Flash J1587
Description Action

636/8 2.5 SID21/8 Sensor rpm camshaft. Abnormal frequency. Engine STOP
takes longer to start than normal. Engine runs nor-
mally once it has started.

637/2 2.4 SID22/2 Sensor rpm flywheel. Irregular signal. Engine is ex- STOP
tremely difficult to start and runs rough or stops.

637/3 2.4 SID22/3 Sensor rpm flywheel. Abnormal frequency. Engine STOP
is extremely difficult to start and runs rough or stops.

637/8 2.4 SID22/8 Sensor rpm flywheel. Abnormal frequency. Engine STOP
is extremely difficult to start and runs rough or stops.

639/FMI 6.5 SID231/FMI Internal error, engine control unit. STOP

Engine off: engine cannot be started. Engine on: en-
gine goes to idle mode and can only be stopped by
using emergency stop.

639/FMI 9.9 SID240/FMI Memory error control unit engine. STOP

May not be possible to start engine.

651/2 7.1 SID1/2 Electrical problem, injector cylinder 1. Engine only STOP
runs on 5 cylinders and has reduced power.

651/3 7.1 SID1/3 Electrical problem, injector cylinder 1. Engine only STOP
runs on 5 cylinders and has reduced power.

651/4 7.1 81D1/4 Electrical problem, injector cylinder 1. Engine only STOP
runs on 5 cylinders and has reduced power.

651/5 7.1 81D1/5 Electrical problem, injector cylinder 1. Engine only 8TOP
runs on 5 cylinders and has reduced power.

651/7 7.1 81D1/7 Compression malfunction or defective injector cylin- 8TOP

der 1. Rough running at low rpm and low load.

651/11 7.1 81D1/11 Electrical problem, injector cylinder 1. Engine only STOP
runs on 5 cylinders and has reduced power.

652/2 7.2 81D2/2 Electrical problem, injector cylinder 2. Engine only 8TOP
runs on 5 cylinders and has reduced power.

652/3 7.2 81D2/3 Electrical problem, injector cylinder 2. Engine only STOP
runs on 5 cylinders and has reduced power. ~.

652/4 7.2 81D2/4 Electrical problem, injector cylinder 2. Engine only STOP
runs on 5 cylinders and has reduced power.

652/5 7.2 81D2/5 Electrical problem, injector cylinder 2. Engine only STOP
runs on 5 cylinders and has reduced power.

652/7 7.2 81D2/7 Compression malfunction or defective injector cylin- STOP

der 2. Rough running at low rpm and low load.

DDRF01.01 GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450
 o Error codes - 1 Engine 13

Display
0
Flash J1587
Description Action

652/11 7.2 S102/11 Electrical problem, injector cylinder 2. Engine only STOP
runs on 5 cylinders and has reduced power.

653/2 7.3 S103/2 Electrical problem, injector cylinder 3. Engine only STOP
runs on 5 cylinders and has reduced power.

653/3 7.3 S103/3 Electrical problem, injector cylinder 3. Engine only STOP
runs on 5 cylinders and has reduced power.

653/4 7.3 S103/4 Electrical problem, injector cylinder 3. Engine only STOP
runs on 5 cylinders and has reduced power.

653/5 7.3 S103/5 Electrical problem, injector cylinder 3. Engine only STOP
runs on 5 cylinders and has reduced power.

653/7 7.3 S103/7 Compression malfunction or defective injector cylin- STOP

der 3. Rough running at low rpm and low load.

653/11 7.3 S103/11 Electrical problem, injector cylinder 3. Engine only STOP
runs on 5 cylinders and has reduced power.

654/2 7.4 S104/2 Electrical problem, injector cylinder 4. Engine only STOP
runs on 5 cylinders and has reduced power.

654/3 7.4 S104/3 Electrical problem, injector cylinder 4. Engine only STOP
runs on 5 cylinders and has reduced power.

654/4 7.4 S104/4 Electrical problem, injector cylinder 4. Engine only STOP
runs on 5 cylinders and has reduced power.

654/5 7.4 S104/5 Electrical problem, injector cylinder 4. Engine only STOP
runs on 5 cylinders and has reduced power.

654/7 7.4 S104/7 Compression malfunction or defective injector cylin- STOP

der 4. Rough running at low rpm and low load.

654/11 7.4 S104/11 Electrical problem, injector cylinder 4. Engine only STOP
runs on 5 cylinders and has reduced power.

655/2 7.5 S105/2 Electrical problem, injector cylinder 5. Engine only STOP
runs on 5 cylinders and has reduced power.

655/3 7.5 S105/3 Electrical problem, injector cylinder 5. Engine only STOP
runs on 5 cylinders and has reduced power.

655/4 7.5 S105/4 Electrical problem, injector cylinder 5. Engine only STOP
runs on 5 cylinders and has reduced power.

655/5 7.5 S105/5 Electrical problem, injector cylinder 5. Engine only STOP
runs on 5 cylinders and has reduced power.

655/7 7.5 S105/7 Compression malfunction or defective injector cylin- STOP

der 5. Engine runs on 5 cylinders, sounds rough and
has reduced power.

Error codes and Wiring diagrams from Workshopmanual ORF 400- DDRF01.01 GB

450 (VORF03.01 GB) ORF 400-450

14 D Error codes - 1 Engine

Display
0
Flash J1587
Description Action

655/11 7.5 SID5I11 Electrical problem, injector cylinder 5. Engine only STOP
runs on 5 cylinders and has reduced power.

656/2 7.6 SID6/2 Electrical problem, injector cylinder 6. Engine only STOP
runs on 5 cylinders and has reduced power.

656/3 7.6 SID6/3 Electrical problem, injector cylinder 6. Engine only STOP
runs on 5 cylinders and has reduced power.

656/4 7.6 SID6/4 Electrical problem, injector cylinder 6. Engine only STOP
runs on 5 cylinders and has reduced power.

656/5 7.6 SID6/5 Electrical problem, injector cylinder 6. Engine only STOP
runs on 5 cylinders and has reduced power.

656/7 7.6 SID6/7 Compression malfunction or defective injector cylin- STOP

der 6. Rough running at low rpm and low load.

656/11 7.6 SID6/11 Electrical problem, injector cylinder 6. Engine only STOP
runs on 5 cylinders and has reduced power.

677/FMI 6.3 PPID3/FMI Starter motor. STOP

1485/3 5.1 PPID5/3 Main relay, cable short-circuited to voltage. Instru- STOP
ment panel loses voltage when ignition key is turned
to start position. Engine does not start.

520192/ 6.8 PPID8/FMI Piston cooling. STOP

FMI

520192/ 6.7 PPID8/FMI Piston cooling. STOP

FMI

520194/ 4.7 PPID4/FMI Starter motor (start request). STOP

FMI

520195/ 4.8 PPID6/FMI Ignition off (stop request). STOP

FMI

DDRF01.01 GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450
 D Error codes - 1 Engine 15

Error codes engine (engine

alternative Cummins aSM11)

Display
0
Flash J1587
Description Action

84/2 241 PID084/2 Sensor speed, data invalid. Engine rpm limited to max. WARNING
rpm without gear.

84/10 242 PID084/10 Sensor speed, incorrect signal. Engine rpm limited to WARNING
max. rpm without gear.

91/3 131 PID091/3 Accelerator pedal, cable short-circuited to voltage. En- STOP
gine does not respond to throttle.

91/4 132 PID091/4 Accelerator pedal, cable short-circuited to ground. En- STOP
gine does not respond to throttle.

91/8 147 PID091/8 Accelerator pedal, too low frequency. Engine does not STOP
respond to throttle.

91/8 148 PID091/8 Accelerator pedal, too high frequency. Engine does not STOP
respond to throttle.

91/19 287 SID091/2 Problem with accelerator pedal. Engine only runs on STOP
idle.

97/3 428 PID097/3 Sensor water in fuel, cable short-circuited to voltage. WARNING

97/4 429 PID097/4 Sensor water in fuel, cable short-circuited to ground. WARNING

97/15 418 PID097/15 Water in fuel. Risk of reduced engine power. WARNING: Drain fuel pre-
filter.

100/1 415 PID100/1 Low engine oil pressure. Engine power is reduced grad- STOP: Check oil level in
ually, after 30 seconds engine is shut off. engine.

100/2 435 PID100/2 Sensor oil pressure, data error. No warning in case of WARNING
low oil pressure.

100/3 135 PID100/3 Sensor oil pressure, cable short-circuited to voltage. No WARNING
warning in case of low oil pressure.

100/4 141 PID100/4 Sensor oil pressure, cable short-circuited to ground or WARNING
open circuit. No warning in case of low oil pressure.

100/18 143 PID100/1 Low engine oil pressure. WARNING: Check oil level
in engine.

102/2 433 PID102/2 Sensor boost pressure indicates high boost pressure WARNING
when other engine data indicate that pressure should be
low. Reduced engine power.

102/3 122 PID102/3 Sensor boost pressure, cable short-circuited to voltage. WARNING
Reduced engine power.

Error codes and Wiring diagrams from Workshopmanual DRF 400- DDRF01.01 GB

450 (VDRF03.01 GB) DRF 400-450

16 D Error codes - 1 Engine

Display
0
Flash J1587
Description Action

102/4 123 PID102/4 Sensor boost pressure, cable short-circuited to ground WARNING
or open circuit. Reduced engine power.

103/16 595 PID103/0 Incorrect overspeed protection for turbocharging. Re- WARNING
duced engine power.

105/0 155 PID105/0 Inlet air too warm. Engine power is reduced gradually, STOP
after 30 seconds engine is shut off.

105/3 153 PID105/3 Sensor charge-air temperature, cable short-circuited to WARNING

voltage or open circuit. No warning at high coolant tem-
perature.

105/4 154 PID105/4 Sensor charge-air temperature, cable short-circuited to WARNING

ground or open circuit. No warning at high coolant tem-
perature.

108/2 295 PID108/2 Sensor air pressure, data error. Reduced engine power. WARNING

108/3 221 PID108/3 Sensor air pressure, cable short-circuited to voltage. Re- WARNING
duced engine power.

108/4 222 PID108/4 Sensor air pressure, cable short-circuited to ground. Re- WARNING
duced engine power.

110/0 151 PID110/0 High coolant temperature. Engine power is reduced STOP: Check coolant level.
gradually, after 30 seconds engine is shut off.

110/3 144 PID110/3 Sensor coolant temperature, cable short-circuited to WARNING

voltage or open circuit. No warning at high coolant tem-
perature.

110/4 145 PID110/4 Sensor coolant temperature, cable short-circuited to WARNING

ground. No warning at high coolant temperature.

111/1 235 PID111/1 Low coolant level. Engine power is reduced gradually, STOP: Check coolant level
after 30 seconds engine is shut off. in engine.

111/2 422 PID111/2 Sensor coolant level, data error. No warning at low cool- WARNING: Check coolant
ant level. level in engine.

166/2 951 PID166/2 Power difference between cylinders. Rough idling. INFORMATION

167/1 598 PID167/1 Low battery voltage. STOP

167/16 596 PID167/0 High battery voltage. WARNING

167/18 597 PID167/1 Low battery voltage or restart of engine repeatedly due WARNING
to low battery voltage.

168/16 442 PID168/0 Voltage feed to control unit engine too high. WARNING

168/18 441 PID168/1 Voltage feed to control unit engine too low. WARNING

DDRF01.01 GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450
 D Error codes - 1 Engine 17

Display
0
Flash J1587
Description Action

175/0 214 PID175/0 High engine oil temperature. Engine power is reduced STOP
gradually, after 30 seconds engine is shut off.

175/3 212 PID175/3 Sensor oil temperature, cable short-circuited to voltage WARNING
or open circuit. No warning at high oil temperature en-
gine.

175/4 213 PID175/4 Sensor oil temperature, cable short-circuited to ground. WARNING
No warning at high oil temperature engine.

188/4 466 SID032/4 Solenoid valve 1 wastegate. Reduced engine power. WARNING

190/0 234 PID190/0 High engine rpm. Fuel supply restricted until engine rpm STOP: Use less throttle.
is below permitted engine rpm.

190/10 121 PID190/10 Sensor rpm/ignition position, one of two signals missing. WARNING

190/2 115 PID190/2 Sensor rpm/ignition position, both signals missing. En- STOP
gine stops and cannot be started.

191/16 349 PID191/0 Incorrect calibration value. Speed limitation activated. WARNING: Reduce throt-
tle.

191/18 489 PID191/1 Speed warning for low speed. WARNING: Increase throt-
tle.

251/2 319 PID251/2 Internal error, engine control unit. INFORMATION

441/3 293 PID441/3 Extra sensor temperature, cable short-circuited to volt- WARNING
age. No warning at high temperature control unit.

441/4 294 PID441/4 Extra sensor temperature, cable short-circuited to WARNING

ground. No warning at high temperature.

558/13 432 SID230/13 Sensor accelerator pedal idle switch, calibration error. STOP
Engine only runs at idle.

558/2 431 SID230/2 Sensor accelerator pedal idle switch, data error. WARNING

558/4 551 SID230/4 Sensor accelerator pedal idle switch, cable short- WARNING
circuited to ground. Engine does not respond to throttle.

608/2 412 SID250/2 Communication error Control unit engine. INFORMATION

608/9 414 SID250/9 Communication error Control unit engine. INFORMATION

626/11 381 SID237/11 Control relay preheating. Preheating not working WARNING

627/2 434 SID251/2 Voltage feed to control unit engine disappears without WARNING
ignition off. Reduced engine power. Difficult to start or
engine stops.

629/12 111 SID254/12 Internal error control unit engine. Engine does not start. STOP

629/12 343 SID254/12 Internal error, engine control unit. WARNING

Error codes and Wiring diagrams from Workshopmanual DRF 400- DDRF01.01 GB

450 (VDRF03.01 GB) DRF 400-450

18 D Error codes - 1 Engine

Display
0
Flash J1587
Description Action

630/2 341 81D253/2 Internal error control unit engine. Reduced engine pow- WARNING
er. Difficult to start or engine stops.

632/3 255 81D017/3 80lenoid valve fuel shut-off, cable short-circuited to volt- WARNING
age.

632/4 254 81D017/4 80lenoid valve fuel shut-off, cable short-circuited to 8TOP
ground. Engine shuts down.

639/2 426 81D231/2 Communication error Control unit engine. INFORMATION

639/9 285 81D231/9 Communication error Control unit engine. WARNING

639/13 286 81D231/13 Communication error Control unit engine. WARNING

644/2 237 81D030/2 Accelerator pedal, sensor outside valid range. Engine WARNING
shuts down.

647/4 245 81D033/4 Fan clutch, cable short-circuited to ground. Cooling fan WARNING
constantly activated.

651/5 322 81D001/5 Electrical problem, injector cylinder 1. Engine only runs WARNING
on 5 cylinders, has reduced power.

651/6 311 81D001/6 Electrical problem, injector cylinder 1. Engine only runs WARNING
on 5 cylinders, has reduced power.

652/5 331 81D002/5 Electrical problem, injector cylinder 2. Engine only runs WARNING
on 5 cylinders, has reduced power.

652/6 315 81D002/6 Electrical problem, injector cylinder 2. Engine only runs WARNING
on 5 cylinders, has reduced power.

653/5 324 81D003/5 Electrical problem, injector cylinder 3. Engine only runs WARNING
on 5 cylinders, has reduced power.

653/6 313 81D003/6 Electrical problem, injector cylinder 3. Engine only runs WARNING
on 5 cylinders, has reduced power.

654/5 332 81D004/5 Electrical problem, injector cylinder 4. Engine only runs WARNING
on 5 cylinders, has reduced power.

654/6 321 81D004/6 Electrical problem, injector cylinder 4. Engine only runs WARNING
on 5 cylinders, has reduced power.

655/5 323 81D005/5 Electrical problem, injector cylinder 5. Engine only runs WARNING
on 5 cylinders, has reduced power.

655/6 312 81D005/6 Electrical problem, injector cylinder 5. Engine only runs WARNING
on 5 cylinders, has reduced power.

656/5 325 81D006/5 Electrical problem, injector cylinder 6. Engine only runs WARNING
on 5 cylinders, has reduced power.

DDRF01.01 GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450
 D Error codes - 1 Engine 19

Display
0
Flash J1587
Description Action

656/6 314 SID006/6 Electrical problem, injector cylinder 6. Engine only runs WARNING
on 5 cylinders, has reduced power.

702/3 527 SID040 Extra input/output 2, cable short-circuited to voltage. WARNING

PID154/3

703/3 529 SID051/3 Extra input/output 2, cable short-circuited to voltage. WARNING

974/3 133 PID029/3 Extra accelerator pedal, cable short-circuited to voltage. STOP
Engine does not respond to throttle.

974/4 134 PID029/4 Extra accelerator pedal, cable short-circuited to ground. STOP
Engine does not respond to throttle.

974/19 288 PID029/2 Problem with accelerator pedal. Engine does not re- STOP
spond to throttle.

1043/3 387 PID221/3 Accelerator pedal reference voltage, short-circuited to WARNING

voltage. Engine runs at idle.

1043/4 443 SID221/4 Accelerator pedal reference voltage, short-circuited to WARNING

ground. Engine runs at idle.

1072/11 388 SID070/11 Signal engine brake 1, short-circuited to ground. WARNING

1073/11 392 SID029/11 Signal engine brake 2, short-circuited to ground. WARNING

1079/3 386 SID232/3 Reference voltage, short-circuited to voltage. Reduced WARNING

engine power.

1079/4 352 SID232/4 Reference voltage, short-circuited to ground. Reduced WARNING

engine power.

1080/3 227 SID232/3 Reference voltage to sensor short-circuited to voltage. WARNING

Reduced engine power. No warning at low oil pressure
or low coolant level.

1080/4 187 SID232/4 Reference voltage to sensor short-circuited to ground. WARNING

Reduced engine power. No warning at low oil pressure
or low coolant level.

1188/3 465 SID032/3 Solenoid valve 1 wastegate. Reduced engine power. WARNING

1189/3 491 SID088/3 Solenoid valve 2 wastegate. Reduced engine power. WARNING

1189/4 492 SID088/4 Solenoid valve 2 wastegate. Reduced engine power. WARNING

1265/4 223 SID085/4 Solenoid valve oil-burn, cable short-circuited to ground. WARNING

1319/2 419 PID102/2 Incorrect value sensor boost pressure. Reduced engine WARNING
power.

1377/2 497 SID114/2 Error in control unit transmission. WARNING

1380/17 219 PID017/1 Low oil level engine. INFORMATION: Check oil
level in engine.

Error codes and Wiring diagrams from Workshopmanual DRF 400- DDRF01.01 GB

450 (VDRF03.01 GB) DRF 400-450

20 D Error codes - 1 Engine

Display
0
Flash J1587
Description Action

1383/31 611 81D151/11 Engine overheated. INFORMATION: Turn off

engine with ignition.

1384/31 299 81D029/14 Engine shutdown. WARNING: Turn off engine

with ignition.

1387/3 297 PID223/3 Extra sensor pressure, cable short-circuited to voltage. WARNING
No warning in case of oil pressure.

1387/4 298 PID223/4 Extra sensor pressure, cable short-circuited to ground. WARNING
No warning in case of oil pressure.

1484/31 211 81D216/11 Error codes in other control units. INFORMATION

DDRF01.01GB Error codes and Wiring diagrams from Workshopmanual DRF 400-
450 (VDRF03.01 GB) DRF 400-450