Scribd
Upload
151 views

Prefinal Quiz 2 Network Sec

The document appears to be a summary of the results of a quiz on OSPF routing protocol configuration and troubleshooting. It shows that the user answered 19 out of 20 questions correctly, earning a grade of 95%. It lists the questions asked in the quiz along with whether the user's answers were correct or incorrect.

Uploaded by

Mark Rosell
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
151 views

Prefinal Quiz 2 Network Sec

The document appears to be a summary of the results of a quiz on OSPF routing protocol configuration and troubleshooting. It shows that the user answered 19 out of 20 questions correctly, earning a grade of 95%. It lists the questions asked in the quiz along with whether the user's answers were correct or incorrect.

Uploaded by

Mark Rosell
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 9

Started on Sunday, 23 January 2022, 12:06 PM

State Finished
Completed on Sunday, 23 January 2022, 12:10 PM
Time taken 4 mins 15 secs
Grade 19.00 out of 20.00 (95%)
Question 1
Correct
Mark 1.00 out of 1.00

Flag question

Question text
DR/BDR elections only occur in point-topoint  networks and do not occur  in
multiaccessnetworks.

Select one:
True
False 

Question 2
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The  Answer   command is used when configuring an OSPFv2 router to
redistribute only a static default route.

Question 3
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Answer  Used to verify vital OSPFv2 configuration information, including
the OSPFv2 process ID, the router ID, networks the router is advertising, the neighbors the
router is receiving updates from, and the default administrative distance, which is 110 for
OSPF.

Question 4
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The show ip protocols command use to verify the OSPFv2 settings.

Select one:
True 
False

Question 5
Correct
Mark 1.00 out of 1.00

Flag question

Question text
A virtual  Answer  is a special OSPF transit area that is used to connect a
remote OSPF network to Area 0.

Question 6
Correct
Mark 1.00 out of 1.00

Flag question
Question text
The OSPF Hello and Dead intervals are configurable on a per-interface basis. 

Select one:
True 
False

Question 7
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Answer  Used to examine the OSPFv2 process ID and router ID. 

Question 8
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The router ID can be manually configured.

Select one:
True 
False

Question 9
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The show ip ospf neighbor command is use to verify if routers form adjacentcy.
Select one:
True 
False

Question 10
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The show ip ospf interface command use to verify active RIP interfaces. 

Select one:
True
False 

Question 11
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which state will OSPF routers transition to when they have converged?

Select one:
a.
Init

b.
 Loading

c.
Full

d.
ExStart
Feedback
Your answer is correct.

Question 12
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The the show ip interface brief command use to verify that interfaces are active.

Select one:
True 
False

Question 13
Correct
Mark 1.00 out of 1.00

Flag question

Question text
If a specific router ID is not configured on an IPv4-based OSPF router, what will the IOS look
for next to determine the router ID?

Select one:
a.
the highest IPv4 address on a loopback interface

b.
the lowest IPv4 address on any enabled interface

c.
the highest MAC address on a loopback interface

d.
the highest MAC address on any enabled interface
Feedback
Your answer is correct.

Question 14
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which configuration will prevent two directly connected Cisco routers from forming an
OSPFv2 neighbor adjacency?

Select one:
a.
Configuring mismatched OSPF process IDs on two adjacent routers

b.
Configuring mismatched MTU values on two adjacent routers

c.
Configuring a router ID on two adjacent routers

d.
Configuring a LAN interface connected to a switch as a passive interface
Feedback
Your answer is correct.

Question 15
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Answer  Used to verify that the router has formed an OSPFv2 adjacency
with its neighboring routers.
Question 16
Correct
Mark 1.00 out of 1.00

Flag question

Question text
A BDR is also elected in case the DR fails. If the DR stops producing Hello packets, the BDR
promotes itself and assumes the role of DR.

Select one:
True 
False

Question 17
Correct
Mark 1.00 out of 1.00

Flag question

Question text
The show ip route ospf command use to verify the routing table.

Select one:
True 
False

Question 18
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Answer  Used to display the OSPFv2 parameters configured on an
interface, such as the OSPFv2 process ID that the interface is assigned to, the area that the
interfaces are in, the cost of the interface, and the Hello and Dead intervals.

Question 19
Incorrect
Mark 0.00 out of 1.00

Flag question

Question text
All other non-DR or BDR routers become DROTHER (a router that is neither the DR nor the
BDR) and DROTHERs only form full adjacencies with the DR and BDR in the network. 

Select one:
True
False 

Question 20
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which show command displays the administrative distance of the routing protocol that is
being used?

Select one:
a.
show ip protocols

b.
show ip ospf neighbor

c.
  show ip ospf interface
d.
show interface
Feedback
Your answer is correct.

You might also like