JIS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS B 8266: Alternative standard for construction of pressure vessels (Amendment 1) ICS 23,020.30 Reference number : JIS B 8266 : 2006 (IE) PROTECTED PY COPYRIGHT 38B 8266 : 2006 Foreword This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Health, Labour and Welfare and the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with the Industrial Standardization Law. Consequently, JIS B 8266:2003 is partially replaced with this Amend- ment. Date of Establishment: 2003-09-30 Date of Revision: 2006-08-25 Date of Public Notice in Official Gazette: 2006-08-25 Investigated by: Japanese Industrial Standards Committee Standards Board JIS B 8266 : 2006, First English edition published in 2007-07 ‘Translated and published by: Japanese Standards Association 41-24, Akasaka, Minato-ku, Tokyo, 107-8140 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. © JSA 2007 rights reserved. Unless otherwise specified, no part ofthis publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan sw PROTECTED PY COPYRIGHTJAPANESE INDUSTRIAL STANDARD, JIS B 8266 : 2006 Alternative standard for construction of pressure vessels (Amendment 1) JIS B 8266 : 2003 is revised as follows. Annex 3 Bolted flanges of pressure vessels Replace Annex 3 Table 2 by the following. Annex 3 Table 2 Gasket materials and contact face! Gasket Materials Gas [Minimum gasket | Seat | Basie kot [design | shapo | taco | width of factor | cightening shape | gasket m | pressure Geo | seat (oe ’ Annex | Annex 8 Nimm? table a) | sable a) ‘Self seal gasket 0 0 7 — — ‘O-ring, metal, rubber and ) regarded as self sealing Joint seal () Thickness 1.5 mm 35 |< metal coated gacket | Monel of 4 to 6 % Cr steel san | xo | CB PROTECTED PY COPYRIGHT2 B 8266 : 2006 Annex 3 Table 2 (concluded) Gases materia Gas [Minimum | Gasker | Sat | Basi fe lass oes fee |i factor | tightening shope | gasket 2 | prowwce Goo | seat (ee ; Annes 3 | Annex 3 ‘ina? taties) | tale Soft amin 238 a YU ovum ype | S0H0nE Oba so ea — Sait elo ion ne | coor Monel metal or 406% Creel M8 Stns ste and nick alo sa Soft aluminum 319 ary Sot eoper er brass tis |S? |ilo Flat type metal Sofi steel or iron 524 aS 1d), cenated gasket ( 2 | EH |20, or | ep a Monel metal 406% Crstee! Stainless steel or nickel alloy Soft uminum on ery Sot opp or brass a ied awtoth asker | Sof sel orton 21 | MO |2 3 Monel or 106960 tel sai Staines ste ikl alloy 6 iat ope metal aw | Sof aluminum wor mena het Saf oppor rss 96 ea Soft steel or iron wir |LOA Jo, 3,4, Monel mel or 1 6%6Cr steel 1803 5 Staines tee nickel alloy i793 Ringjoin gasket Soft steel or iron Monel metal or 410 6 % Cr steel 6.00 Stainless ste! or nickel alloy 1240 © 6 Note (1) NOTES 1 These gaskets are all asbestos-free. For use these gaskets, confirm mvalue, svalue and the applicable temperature range. Gasket factor m shall apply onl the inside of the inner circumfe to the gasket which entirely exists in rence of the bolt holes. Overlapping section of the metal of the flat metal clad gasket marked with * shall not be faced with the nabbing (projected contact surface) shown in the seat shapes of 1c, 1d and 2 of Annex 3 table 3. This table shows commonly used materials and shapes of contact surfaces of gaskets with the values of m and y. Values of m and y shown in this table are recommendation and in case there is sufficient ground, these values may not necessarily be used. In the case of seal-welded flanges using no gaskets which have the seal ing effect by the seal welding, the gasket factor m and minimum design tightening pressure y may be assumed to be zero. PROTECTED PY COPYRIGHTErata for JIS (English edition) are printed in Standardization Journal, published monthly by the Jupanose Standards Association, and also provided to subseribors of JIS (English edition) in Monthly Information, Errata will be provided upon request, plense contact: Standardization Promotion Department, Japanese Standards Association 461-24, Akasaka, Minatorku, Tokyo, 107-8140 JAPAN TEL. 03-3585-8002 FAN, 03-3585-0462 CTED PY COPYRIGHT