Testing and Adjusting

308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B
Excavators Engine and Pump Control
Medi
Media
a Num
umbe
ber
r -REN
RENR19
R1998
98--06 Pub
ubllica
icatio
tion Date -0
-01/
1/1
10/200
/2004
4 Date Upda
pdate
ted
d -06
06/1
/10
0/2
/200
004
4

i02161676

Governor
Governor Actuat
Actuator
or - Calib
Calibrate
rate
SMCS -  1716-524
 

Monitor Panel

This function allows the controller to memorize the corresponding data from the rotation angles of 
the governor actuator and the no-load
no-load engine speed. The controller
controller will determine the target
 position of the
t he governor actuator.

This procedure must be performed when any of the following components have been replaced or 
the components
components are reinstalled: The governor actuator
actuator,, the accelerator cable and the controller.
controller.

The temperature
temperature of the hydraulic
hydraulic oil must be at approximately
approximately 50 °C (122 °F).

1. Enter service code 70. The character display

display shows the followin
following
g example: "70 P00". This
means "before calibration".

2. Depress the travel

travel alarm cancel switch (22). The character
character display shows
shows the following
following
example: 7001This means "governor actuator is moving to the initial position".

3. When the character display

display shows the following examp
example,
le, the governor actuator
actuator has
completed a movement to an initial position: "70 PSP".

4. At this condition,
condition, install the accelerator
accelerator cable prope
properly,
rly, if the cable is not installed.

5. Start the engine.

engine.

6. Depress the travel alarm cancel switch (22) again. The calibration
calibration for the governor actuator 
actuator 
will start. During the calibration, the character display displays the following codes:

Table 1
Calibration Codes For The Governor Actuator

Calibration Codes
Description

70 P00 Before Calibration

7001
7001 Shif
Shiftt The
The Gove
Govern
rnor
or Actu
Actuat
ator
or (G/A
(G/A)) To The
The In
Init
itia
iall Posi
Positi
tion
on
70 PSP
PSP The
The G/
G/A
A Has
Has Comp
Comple
lete
ted
d A Move
Move To The
The In
Init
itia
iall Posi
Positi
tion
on

7003 Sear
arcch The G/A Positio
tion For High Idle

7004 Set The G/A Posi

siti
tio
on For Hi
Hig
gh Id
Idlle

  Collect
Collect The Data Of G/A Positions
Positions From The Engine
Engine Speed Dial 9
7005
to 2

7006 Sear
arcch The G/A Positio
tions For Low Idle

  Collect
Collect The Data Of G/A Positions
Positions From The Engine
Engine Speed Dial
7007
Positions 9 To 2

7008 Confirm The G/A Posi

siti
tio
on For High Id
Idlle

7009
 

Confirm The G/A Positions From The Engine Speed Dial Positions
9 To 1

  Confirm The G/A Positions From The Engine Speed Dial Positions
7010
2 to 10

7011
7011 Coll
Collec
ectt The
The Data
Data For
For The
The Engi
Engine
ne Spee
Speed
d Fe
Feed
edba
back
ck Cont
Contro
roll

70 End Calibration Is Complete

7. When the calibration

calibration has been completed,
completed, the character
character display shows "70 E nd".

Note: In order to stop the calibration in the middle of the process, the power mode switch
(19) and travel alarm cancel switch (22) should be pressed and held simultaneously
simultaneously for 2
seconds or more.

8. An error will be present, if the governor

governor actuator is movin
moving g to the initial position or being
being
calibrated
calibrated and the character display is showing the letter "H" in the fourth character
character position
from the right and not showing a character in the third character position from the right.
Depress the travel alarm cancel switch (22). The error code is displayed
displayed on the right three
characterr positions. Refer to the following
characte following chart for details of the possible
possible error codes.

9. When the calibration

calibration has been completed,
completed, the character
character display shows "70 E nd".

Note: In order to stop the calibration in the middle of the process, the power mode switch
(19) and the travel alarm cancel switch (22) are pressed and held simultaneo
simultaneously
usly for 2
seconds or more.

10. An error will be present, if the governor

governor actuator is movin
moving g to the initial position or being
being
calibrated
calibrated and the character display is showing the letter "H" in the fourth character
character position
from the right and not showing a character in the third character position from the right.
Depress the travel alarm cancel switch (22). The error code will be displayed in the right
three character positions.
positions. Refer to the following
following chart for the details of the possible
possible error 
codes.

Table 2
Error Code Display
Character Error Description
  70 HF 01
1 Engine Stops

  70 HF 02
2 Speed Sensor Is Abnormal

  70 HF 03
3 Load Is Applied

  70 HF 04
4 Faster Than The High Idle Speed

  70 HF 05
5 Slower Than The Low Idle Engine Speed
6 Governor Actuator Feedback  
 

70 HF 06

  70 HF 07 Governor
Governor Actuator
Actuator Feedback
Feedback Sensor
Sensor Circuit
Circuit Is Shorted
Shorted
7
To Ground

  70 HF 08
8 Feedback Signal Of Governor Actuator Is Abnormal

  70 HF 09 High idle engine speed is lower than the Engine

Engine Speed
9 Dial Setting 8 plus 50 rpm
70 Hd 00
Retry Error Or Too Much Hysteresis

11. Perform
Perform the following
following operations
operations when the character display shows
shows "70 Hd 00".

a. Depress the fine contr

control
ol mode switch and hold
hold the fine control mode switch (25
(25)) until
the character display stops blinking.

 b. Depress the boom priority mode switch

swit ch (23)
( 23) or the swing priority mode switch
swit ch (24) in
order to select the data that is used as the calibration data.

c. Depress the boom pri

priority
ority mode
mode switch (23) in order to select the previous
previous calibration
data.

d. Depress the swing

swing priority mod
modee switch in order to select the default calibrat
calibration
ion data.

e. Depress the trave

travell alarm cancel switch (22) in order to memoriz
memorizee the calibration data
that has been selected.

12. When the calibration

calibration is completed,
completed, the character display may flash "70End".
"70End". Then, a
number will be displayed. The cable end for the governor actuator is too loose by 6 full
turns, if a set of numbers that is similar to "70 06" is displayed. The numbers on the right
side indicate the total number of turns. The display numb
numbers
ers in each position
position can be from 1
through 0.

The cable end of the governor actuator is too tight by 6 full turns, if a set of numbers that is similar 
to "70 - 06" appears in the fourth position from the left with a minus sign. Again, the numbers on
the right side indicate
indicate the total number of turns.

The four numbers on the right side will indicate the actual engine speed, if a set of numbers that
are similar to "70 20 13" appear in the third set. This code means that the engine speed is below
the correct specifications
specifications for the high idle speed of the engine.
engine.