Scribd
Upload
230 views24 pages

Digital Profile Radiography - Practical Uses and Limitations

This document discusses digital profile radiography for online piping thinning assessment. It provides an introduction to digital radiography and explains how it is similar to conventional radiography but uses reusable digital media instead of film. It outlines some advantages like instant results but also limitations like restrictions to smaller pipe sizes. It discusses international standards for digital radiography testing and shows pipe size limitations based on radiation source. It emphasizes how the technology allows detecting both internal and external pipe degradation and insulation conditions. Potential sources of error from improper setup are explained. Finally, it shows some sample digital radiography images.

Uploaded by

Mohan Raj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
230 views24 pages

Digital Profile Radiography - Practical Uses and Limitations

This document discusses digital profile radiography for online piping thinning assessment. It provides an introduction to digital radiography and explains how it is similar to conventional radiography but uses reusable digital media instead of film. It outlines some advantages like instant results but also limitations like restrictions to smaller pipe sizes. It discusses international standards for digital radiography testing and shows pipe size limitations based on radiation source. It emphasizes how the technology allows detecting both internal and external pipe degradation and insulation conditions. Potential sources of error from improper setup are explained. Finally, it shows some sample digital radiography images.

Uploaded by

Mohan Raj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

Digital Profile Radiography

– Practical uses and limitations

Mr. Neil Young


Asset Reliability Inspections
Bunbury, Australia
www.ari.com.au
[email protected]

15th APCNDT 2017 Singapore


Introduction
Profile digital radiography for online
piping thinning assessment has been
in use in Australia since 2005 and
recently is gaining significantly more
acceptance/use.
Today all major refineries in Australia
use digital imaging for pipe inspection.
This is helped by new international
standards.
This workshop aims to explain the uses
and limitations of this technology with
some real world samples.

15th APCNDT 2017 Singapore


Digital Radiography – What is it?
Essentially the same as conventional film radiography with the
exception that the image is captured via reusable digital media instead
of film, at a lower radiation dose by either a Digital Detectors Array
(DDA) panel or on a Phosphor Imaging Plate (PIP or IP).
Industry separates the two mediums by calling DDA – Digital
Radiography (DR) and IP – Computed Radiography (CR).

15th APCNDT 2017 Singapore


Advantages / Disadvantages
• Instant results (DDA) – no reshoots • High initial capital costs
• Fast results (CR) – easy onsite processing • Restricted to smaller size pipes
• Software for wall thickness evaluation • Additional training
• Easily shared (email an image) • Radiation exclusion zones
• No chemical dark rooms • Digital, poor data in = poor data out
• Broader area (you get the bigger picture) • DDA lower spatial resolution than film
• Higher dynamic range
• Higher productivity & automated
workflows
• Ability to “hunt” degradation

15th APCNDT 2017 Singapore


Methods of test - Standards
• BS EN 16407-1 Non-destructive testing – Radiographic inspection of
corrosion and deposits in pipes X- and gamma rays Part 1:
Tangential radiographic inspection
• BS EN 16407-2 Non-destructive testing — Radiographic inspection
of corrosion and deposits in pipes by X- and gamma rays Part 2:
Double wall radiographic inspection

15th APCNDT 2017 Singapore


Pipe Size Limitations
(what is readily achievable)
You are restricted on what pipe size / schedule you can test. This
restriction is due to the different penetrating power of the radiation
type used which is referred to a Wmax in EN16407.1
(referred to as chord length in conventional Australian standards)

15th APCNDT 2017 Singapore


Standard prescribes maximum allowable thickness (Wmax)
for different types of radiation (different penetrating power)

15th APCNDT 2017 Singapore


What does this equate to for two commonly used gamma sources?
Ir192 Se75
Sch40 Sch80 Sch160 Sch40 Sch80 Sch160
DN 15-65 Yes Yes Yes Yes Yes Yes
DN 80 Yes Yes Yes Yes Yes No
DN 90 Yes Yes N/A Yes Yes N/A
DN 100 Yes Yes No No No No
DN 125 Yes Yes No No No No
DN 150 Yes Yes No No No No
DN 200 No No No No No No

What does this mean?


• Using Se75 for smaller exclusion zones etc gives you less scope than Ir192
• Both sources are only useable on smaller piping
• If using battery powered pulsed X-ray units again for exclusion zones/safety
you are more restricted again than when using Se75
• Larger pipes need to be examined with ultrasonic or eddy current techniques
TIP: Fittings are thicker so if you have designed a PRT scope on the upper limits based on pipe size/schedule you will
struggle for accurate data on the fittings (elbows, Tees etc) attached to these pipes [which is typically where you are
looking with flow/direction changes]

NDT in Canada 2017 Conference


Insulation – Internal and External pipe
degradation
A key advantage of this technology is that by looking at the image you detect
internal (flow/contents) degradation and/or external corrosion (CUI)
If you detect CUI at early stages you can then address the issue/s with a
repair before costly replacements
EN16407-01 Standard prescribes a visual assessment of the area as well by
stating on the test report the “condition of the insulation”
• No point in getting a satisfactory radiographic result and not being
advised of degradation of the insulation that will affect the result at
the next inspection
• With the right service provider you can get a visual examination of
the lagging and the thickness result
• Our reports detail this and include a set up image which can double
as record of condition of the recording point at time of test

15th APCNDT 2017 Singapore


15th APCNDT 2017 Singapore
Order of Accuracy – Set up mistakes
• Image Calibration – Test arrangement OR Reference Object

• Understand where you want to test – intrados/extrados, washout,


flow/impact

15th APCNDT 2017 Singapore


Tangential Offset - Ensure you are “square” with the wall you are
trying to examine

Detector
Misalignment

Pipe
Misalignment

Source
Placement
Larger pipes don’t then go “measuring” the other side

15th APCNDT 2017 Singapore


Tangential Centerline - Ensure your source is central and your comparator
ball is offset to correctly capture the enlargement
(examine both sides)

15th APCNDT 2017 Singapore


Reducing The Human Factor
• All previous sources of error are human and are reducible
• Ask for ISO9712 certification such as that offered by the AINDT

• Ask for specific ISO17025 accreditation offered by NATA

NDT in Canada 2017 Conference


Sample Images
Wrapped Temporary Repair Pipe Test

15th APCNDT 2017 Singapore


Sample Images
Soil Air Interface – External Corrosion Blisters

15th APCNDT 2017 Singapore


Sample Images
Bigger Picture

15th APCNDT 2017 Singapore


Sample Images
Wire Rope Trials

15th APCNDT 2017 Singapore


Software Demonstration
• Fittings are thicker
• Upper limit struggles
• Oxide separation wall thickness tool
• Holed
• Tangential offset opposite calibration side variations

15th APCNDT 2017 Singapore


Fittings Are Thicker

NDT in Canada 2017 Conference


Enlargement

15th APCNDT 2017 Singapore


Water Filled

NDT in Canada 2017 Conference


Oxide layer Separation

15th APCNDT 2017 Singapore


Debris Trap

15th APCNDT 2017 Singapore

You might also like