Nice

MC424L

Control unit

EN - Instructions and warnings for installation and use

 ENGLISH 1 GENERAL SAFETY WARNINGS AND
PRECAUTIONS
Translation of the original instructions in full 1 GENERAL SAFETY WARNINGS AND PRECAUTIONS

a Prior to installing the appliance, carefully read and

observe these instructions, since incorrect installa-
tion can cause serious harm to people and damage
CONTENTS to the appliance. Store them with care.

a According to the latest European legislation, an

1 GENERAL SAFETY WARNINGS AND PRECAUTIONS . . . . 2 automated device must be constructed in conform-
2 PRODUCT DESCRIPTION AND INTENDED USE . . . . . . . . . 3 ity to the harmonised rules specified in the current
2.1. List of control unit parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Machinery Directive, which allow for declaring the
3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 presumed conformity of the automation. Conse-
3.1. Pre-installation checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 quently, all the operations for connecting the prod-
3.2. Product usage limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 uct to the mains electricity, its commissioning and
3.3. Product identification and overall dimensions. . . . . . . . . . . . 4
3.4. Typical installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 maintenance must be carried out exclusively by a
3.5. Installing the control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 qualified and expert technician.
4 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1. Preliminary checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 a In order to avoid any danger from inadvertent re-
4.2. Wiring diagram and description of connections. . . . . . . . . . 6
4.2.1. Wiring diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 setting of the thermal cut-off device, this appliance
4.2.2. Description of connections. . . . . . . . . . . . . . . . . . . . . . . . 7 must not be powered through an external switching
4.2.3. Operations for connection . . . . . . . . . . . . . . . . . . . . . . . . 7 device, such as a timer, or connected to a supply
4.2.4. Notes on connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 that is regularly powered or switched off by the cir-
4.2.5. ALT (STOP) input type . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 cuit.
4.3. Initial start-up and electrical connections test. . . . . . . . . . . . 9
4.4. Motor selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 WARNING! Please abide by the following warnings:
4.5. Automatic limit switch search and “STOP” input
acquisition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 –– Before commencing the installation, check the “Prod-
5 TESTING AND COMMISSIONING . . . . . . . . . . . . . . . . . . . . 11 uct technical specifications”, in particular whether this
5.1.Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 product is suitable for automating your guided part.
5.2.Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Should it not be suitable, do NOT proceed with the in-
6 PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 stallation.
6.1. Using the programming buttons. . . . . . . . . . . . . . . . . . . . . 11 –– The product cannot be used before it has been com-
6.2. Pre-set functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.3. Level 1 programming (ON-OFF). . . . . . . . . . . . . . . . . . . . . 12 missioned as specified in the “Testing and commis-
6.3.1. Level 1 programming procedure . . . . . . . . . . . . . . . . . . 12 sioning” chapter.
6.4. Level 2 programming (adjustable parameters). . . . . . . . . . 13 –– Before proceeding with the product’s installation,
6.4.1. Level 2 programming procedure . . . . . . . . . . . . . . . . . . 13 check that all the materials are in good working order
6.5. Memory deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 and suited to the intended applications.
6.6. Memorising the transmitters . . . . . . . . . . . . . . . . . . . . . . . . 15
–– The product is not intended for use by persons (includ-
6.6.1. Procedure for memorising transmitter buttons. . . . . . . . 15
6.6.2. Number of transmitters that can be memorised. . . . . . . 15 ing children) with reduced physical, sensory or mental
6.6.3. Transmitter memorisation and deletion procedures. . . . 15 capacities, nor by anyone lacking sufficient experience
6.7. LOCKING AND UNLOCKING THE MEMORY. . . . . . . . . . . 17 or familiarity with the product.
7 TROUBLESHOOTING... (troubleshooting guide). . . . . . . . 17 –– Children must not play with the appliance.
7.1. Signalling through warning light . . . . . . . . . . . . . . . . . . . . . 17 –– Do not allow children to play with the product’s control
7.2. Signals on the control unit. . . . . . . . . . . . . . . . . . . . . . . . . . 18 devices. Keep the remote controls out of reach of chil-
7.3. Maintenance notification. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 dren.
7.4. Anomaly log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
–– The system’s power supply network must include a dis-
8 FURTHER INFORMATION (Accessories) . . . . . . . . . . . . . . 20 connection device (not supplied) with a contact open-
8.1. Connecting an SM-type radio receiver. . . . . . . . . . . . . . . . 20
8.2. Connecting the IBT4N interface . . . . . . . . . . . . . . . . . . . . . 20 ing gap permitting complete disconnection under the
8.3. Connecting the PS124 back-up battery . . . . . . . . . . . . . . . 20 conditions envisaged by Overvoltage Category III.
8.4. Connecting the Solemyo system. . . . . . . . . . . . . . . . . . . . . 21 –– During the installation process, handle the product with
9 PRODUCT MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 21 care by avoiding crushing, impacts, falls or contact
10 PRODUCT DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 with liquids of any kind. Do not place the product near
11 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 22
sources of heat nor expose it to open flames. All these
actions can damage the product and cause it to mal-
12 CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 function, or lead to dangerous situations. Should this
INSTRUCTIONS AND WARNINGS FOR THE USER . . . . . 23 occur, immediately suspend the installation process
and contact the Technical Assistance Service.
–– The manufacturer declines all liability for damages to
property, objects or people resulting from failure to
observe the assembly instructions. In such cases, the
warranty for material defects shall not apply.
–– The weighted sound pressure level of the emission A is
lower than 70 dB(A).
–– Cleaning and maintenance reserved for the user must
not be carried out by unsupervised children.
–– Before working on the system (maintenance, cleaning),
always disconnect the product from the mains power
supply.

2 – ENGLISH
 –– Inspect the system frequently, in particular the cables, –– The packing materials of the product must be disposed
springs and supports to detect any imbalances and of in compliance with local regulations.
signs of wear or damage. Do not use the product if it
needs to be repaired or adjusted, because defective
installation or incorrect balancing of the automation can
lead to injuries.

2 PRODUCT DESCRIPTION AND INTENDED USE

MC424L is an electronic control unit for the automation of swing gates MC424L can command 24 V WINGO, TOO, SFAB elec-
2 PRODUCT DESCRIPTION AND INTENDED USE

tro-mechanical actuators. it incorporates an amperometric device that verifies the force of the motors connected to it. This system
allows for automatically detecting the limit switches, memorising the work times of each motor and detecting any obstacles during
normal gate movement. These characteristics simplify the installation considerably, as the leaf offsets and work times do not require
any adjusting.
The control unit is programmed in advance for the most frequently used functions and incorporates a radio receiver for the remote
controls. In addition, a straightforward procedure can be implemented to select more specific functions (see the “PROGRAM-
MING” chapter).
MC424L is equipped with an SM-type connector for slot-in radio receivers (see the “Connecting an SM-type radio receiver“
paragraph) and an IBT4N-type connector which, through the IBT4N interface, can be used to connect BusT4 devices, such as the
Oview programmer (see the “Connecting the IBT4N interface” paragraph).
The control unit is configured for being powered with PS124 back-up batteries which, in case of a power outage, function as an
emergency power supply (see the “Connecting the PS124 back-up battery” paragraph). Moreover, the MC424L is configured for
being connected to a Solemyo solar power kit (see the “Connecting the Solemyo system” paragraph).

a Any use of the product other than the intended use described is not allowed!
2.1 LIST OF CONTROL UNIT PARTS
The control unit is made up of an electronic command and control board housed and protected inside the box. “Figure 1” shows
the main parts making up the board.

1
L10 L12
E F G H I M N
OK L9 L11 L13
M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13

R
S L1 .. L8
L
N P1
U D
T P2

C P3

P4
B
LR

A
O

A 24 V~ power supply connector L1..L8 Programming LED

B Connector for PS124 back-up battery / Solemyo solar LR Radio programming LED
power kit M Input terminals
C Service fuse (2 A, type F) N Terminals for radio antenna
D “SM” connector for radio receiver O Motor selector
E M1 motor terminal (starts first during the closing Q Connector for IBT4N
phase) R Mains fuse
F M2 motor terminal (starts first during the opening S Mains power supply (L-Live; N-Neutral)
phase) T Earth connection
G Warning light terminal U Cable clamp
H OGI output or electric lock terminal P1..P3 Control unit programming buttons
I 24 VDC terminals for services and phototest P4 Radio programming button
L9..L13 Input LEDs
OK “LED OK” status LED
ENGLISH – 3
 3.4 TYPICAL INSTALLATION
3 INSTALLATION “Figure 3” shows an example of an automation system con-
3 INSTALLATION

structed using Nice components.

3.1 PRE-INSTALLATION CHECKS 3 C

Before proceeding with the product’s installation, it is necessary
to:
–– check the integrity of the supply H D
–– check that all the materials are in good working order and
G E E
suited to the intended use
–– check that all operating conditions comply with that specified G A B
in the “Product usage limits” paragraph and in the “TECHNI-
F F
CAL SPECIFICATIONS” chapter
–– check that the chosen installation location is compatible with
the product’s overall dimensions (see “Figure 2”)
–– check that the surface chosen for installing the product is sol-
id and can ensure stable attachment A WINGO, TOO, SFAB 24 V electro-mechanical actuator
–– make sure that the installation area is not subject to flooding; if B WINGO, TOO, SFAB 24 V electro-mechanical actuator
necessary, the product must be installed appropriately raised C Warning light
above ground level D Key selector
–– check that the space around the product allows safe and easy E “PHOTO” pair of photocells
access F “PHOTO1” pair of photocells
–– check that all electrical cables to be used belong to the type G “PHOTO2” pair of photocells
listed in “Table 1” H Control unit
–– check that the automation has mechanical stops in both the
opening and closing phases. These above-mentioned components are positioned according
to a typical standard layout.
In particular, bear in mind that:
3.2 PRODUCT USAGE LIMITS –– for the characteristics and connection of the photocells, con-
The product must be used exclusively with WG2024, WG3524, sult the specific instructions of the product
WG4024, WG5024, TOO3024, TOO4524, XME2024 gearmotors –– the intervention of the “PHOTO” pair of photocells during the
and in accordance with the corresponding usage limits. opening phase has no effect, while it triggers a reversal during
the closing phase
3.3 PRODUCT IDENTIFICATION AND OVERALL –– the intervention of the “PHOTO1” pair of photocells stops the
manoeuvre during both the opening and closing phases
DIMENSIONS –– the intervention of the “PHOTO2” pair of photocells during the
The overall dimensions and label (A) that allow for identifying the closing phase (connected to the suitably configured AUX in-
product are shown in “Figure 2”. put) has no effect, while it triggers a reversal during the open-
ing phase.
2
l Bear in mind that motor M1 is the first to start for
the closing movement, while motor M2 is the first to
start for the opening movement (“Figure 4”).

4
122 mm

23 m
2m 0m
m 31

M1 M2

a Before proceeding with the installation, prepare the

electrical cables required for the system by refer-
ring to the “Wiring diagram and description of con-
nections” paragraph and to that specified in the “
TECHNICAL SPECIFICATIONS” chapter.

a The cables used must be suited to the type of envi-

ronment of the installation site.

a When laying the ducting for routing the electrical

cables and for the cable entry point into the control
unit housing, check that there are no water depos-
its in the junction wells nor condensate in the con-
nection ducts, as water and damp conditions could
damage the product’s electronic circuits.

4 – ENGLISH
3.5 INSTALLING THE CONTROL UNIT
6
a Secure the control unit to an unmovable, vertical,
flat surface adequately protected against possible
impacts. The lower part of the control unit must be
at least 40 cm above the ground.
20
5m
l The control unit is also suitable for being installed m
outdoors, as it is supplied in a container that, if ad-
equately installed, guarantees an IP54 protection
rating.
To secure the control unit (“Figure 5” and “Figure 6”):
1. loosen the screws (A) and remove the cover (B) of the

237 mm
control unit
2. identify the pre-cut holes (C) located along the lower side
of the box and perforate the ones used to pass the elec- G
trical cables

l The side cable entry (D) can only be used if the con-
trol unit is installed indoors, in a protected environ-
ment.
E
5 F

B
A

D
4 ELECTRICAL CONNECTIONS
4 ELECTRICAL CONNECTIONS

4.1 PRELIMINARY CHECKS

C
f All electrical connections must be made with the
system disconnected from the mains electricity and
with the back-up battery (if present) disconnected.

a The connection operations must only be carried out

by qualified personnel.
3. drill the wall (E) by observing the measurements shown in
the figure and arrange suitable wall plugs (not supplied) f Check that all electrical cables to be used are of the
4. position the box (F) and fasten it with the screws (G) (not suitable type
supplied)
5. arrange cable glands for passing the connecting cables
6. make the electrical connections by operating as de-
scribed in the “ELECTRICAL CONNECTIONS” chapter.

l To install any other devices used on the automated

system, refer to the respective instruction manuals.
7. after making the electrical connections, put the cover (B)
back on and tighten the screws (A).

ENGLISH – 5
4.2 WIRING DIAGRAM AND DESCRIPTION OF CONNECTIONS

4.2.1 Wiring diagram

A Connection with “Stand-by all” active B Standard connection: without using the
(energy saving) “Stand-by all” and without the “Phototest”

TX RX TX RX

5 - 10 RX = PHOTO
5 - 11 RX = PHOTO1 8-10 RX = PHOTO
5 - 13 RX = PHOTO2 8-11 RX = PHOTO1
8-13 RX = PHOTO2 (AUX)

OGI
OGI

PHOTO2

M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13 M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13

C Connection without the “Stand-by all” D Connection without the “Stand-by all”, with the
and with the “Phototest” “Phototest” and without the “Photo1”

TX RX TX RX

8-10 RX = PHOTO 8-10 RX = PHOTO

8-11 RX = PHOTO1
8-13 RX = PHOTO2 (AUX)
OGI

OGI

M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13 M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13

6 – ENGLISH
4.2.2 Description of connections
The meaning of the codes/wording stamped on the electronic board near the relative terminals is described below.
Table 1
ELECTRICAL CONNECTIONS
Terminals Function Description Cable type
120/230/250 V ~ 50/60
Mains power supply 3 x 1.5 mm2
Hz POWER SUPPLY
Motor 1 Connection of motor M1 [note 1] 3 x 1.5 mm2
Motor 2 Connection of motor M2 3 x 1.5 mm2
1÷2 Warning light Connection of the 24 V c max 25 W warning light 2 x 1 mm2
OGI: 2 x 0.5 mm2
Connection of the 24 V c max 5 W Open Gate Indicator or 12 V c max 15
3÷4 OGI / Electric lock Electric lock: 2 x 1
VA Electric Lock (see the “PROGRAMMING” chapter)
mm2
24 V c common
+24 V c power supply for TX photocells with phototest (max 100 mA);
5 input (with Stand-by 1 x 0.5 mm2
“COMMON” for all safety inputs, with “Stand-by all” function active [note 2]
all / phototest)
6 0Vc 0 V power supply c for services 1 x 0.5 mm2
7 24 V c Services power supply, without “Stand-by all” (24 V c max 200 mA) 1 x 0.5 mm2
8 Common 24 V c Common for all inputs (+24 V c) without “Stand-by all” 1 x 0.5 mm2
9 ALT (STOP) Input with STOP function (emergency, safety lock) [note 3] 1 x 0.5 mm2
10 FOTO (PHOTO) NC input for safety devices (photocells, sensitive edges) 1 x 0.5 mm2
11 FOTO1 (PHOTO1) NC input for safety devices (photocells, sensitive edges) 1 x 0.5 mm2
PASSO-PASSO
12 Input for cyclic operation (OPEN-STOP-CLOSE-STOP) 1 x 0.5 mm2
(STEP-BY-STEP)
13 AUX Auxiliary input [note 4] 1 x 0.5 mm2
RG58-type shielded
Antenna Radio receiver antenna connection
cable
Note 1 Not used for single-leaf gates (the control unit automatically recognises whether there is only one motor installed).
Note 2 The “Stand-by all” is used to limit consumption; for further details on the electrical connections, refer to the “Stand-by all /
Phototest connection” paragraph, and consult the “PROGRAMMING” chapter for information on programming.
Note 3 The ALT (STOP) input can be used for NC contacts or 8.2 kΩ fixed resistor contacts in self-recognition mode (see the “
PROGRAMMING” chapter).
Note 4 The AUX auxiliary input is programmed by default with the “Type 1 partial open” function, but can be programmed with one
of the functions shown in “Table 2”.
Table 2
PROGRAMMABLE FUNCTIONS FOR THE AUX INPUT
Function Type of input Description
TYPE 1 PARTIAL OPEN NO (normally open) Opens the upper leaf completely
TYPE 2 PARTIAL OPEN NO (normally open) Opens the two leaves halfway
OPEN NO (normally open) Performs the open manoeuvre only
CLOSE NO (normally open) Performs the close manoeuvre only
PHOTO 2 NC (normally closed) PHOTO 2 function
STOP NO (normally open) Stops the manoeuvre
EXCLUDED -- No function

4.2.3 Operations for connection

To make the electrical connections (“Figure 7”): 8
1. remove the terminals from their housings
2. connect the various devices to the relevant terminals ac-
cording to the diagram shown in “Figure 7”
3. put the terminals back into their housings.
4. connect the power supply cable to points (A) and (B) and
secure it with the cable clamp (C) (“Figure 8”).

A
L
N
C
B T

ENGLISH – 7
4.2.4 Notes on connections Connection of the selector to carry out the “STEP-BY-STEP”
Most of the connections are extremely easy to make, as they are functions and one of those relevant to the AUX auxiliary input
largely connections directed at a single user or contact. Below (PARTIAL OPENING, OPEN ONLY, CLOSE ONLY, etc.) (“Fig-
are some examples on how to connect external devices. ure 10”).

4.2.4.1 Stand-by all / Phototest connection 10

The “Stand-by all” function allows for reducing consumption and STEP BY STEP AUX
is active as a standard feature. It is automatically excluded only
when the “Phototest” function activates.
NC NO C C NO NC
Note The “Stand-by all” and “Phototest” functions are alterna-
tive, as one excludes the other.
The possible connection options are listed below:
–– with “Stand-by all” active (energy saving) (“Figure 7 A”)
–– without “Stand-by all” and without “Phototest” (standard con-
nection) (“Figure 7 B”)
–– without “Stand-by all” and with “Phototest” (“Figure 7 C”).
With the “Stand-by all” function active, 1 minute after the end of 12 8 8 13
the manoeuvre the control unit enters the “Stand-by all” mode
by switching off all the inputs and outputs to limit consumption.
The relevant status is signalled by the “OK” LED, which starts
flashing more slowly. 4.2.4.3 Connecting the Open Gate Indicator / Electric
Lock
m If the control unit is powered with a photovoltaic The OGI (Open Gate Indicator) output, if suitably programmed,
panel (“Solemyo” system) or with a back-up bat- can be used as a “Open Gate Indicator”. The indicator light
tery, the “Stand-by all” function must be activated will flash slowly during the opening phase and quickly during
as shown in the “energy saving” diagram (“Figure the closing phase. It will remain steady lit with the gate open
7 A”). (stopped) and off with the gate closed. If the output is pro-
grammed as an electric lock, it activates for 3 seconds whenev-
When the “Stand-by all” function is not required, the “Phototest” er an opening manoeuvre starts (“Figure 11”).
function can be activated, which can be used to verify – at the
start of each manoeuvre – whether the connected photocells are
working properly. To use this function, it is necessary to connect 11 3 4
the photocells appropriately (“Figure 7 C”) and then activate
the function.
Note By activating the “Phototest” function, the inputs sub-
ject to the testing procedure are PHOTO, PHOTO1 and
PHOTO2. If one of these inputs is not used, it must be
connected to the “PHOTOTEST” terminal (number 5)
("Figure 7 D").

4.2.4.2 Key selector connection OGI EL

Connection of the key selector to perform the “STEP-BY-STEP” 3
and “STOP” functions (“Figure 9”). 4 33Vc 12Va
max 5 W max 15 VA
9

STEP BY STEP ALT

4.2.5 ALT (STOP) input type
NC NO C C NO NC The MC424L control unit can be programmed to configure two
types of ALT (STOP) inputs:
–– NC-type STOP for NC contacts
–– Fixed resistor STOP type for connecting devices with 8.2 kΩ
fixed resistor output (e.g. sensitive edges) to the control unit.
The input measures the resistor’s value and removes the ma-
noeuvre consent when the resistor exceeds the nominal val-
ue. With suitable arrangements, normally open (NO), normally
12 8 8 9 closed (NC) and even multiple devices of a different type can
be connected to the ALT input, configured as a fixed resistor
(see “Table 3”).

m To connect ALT (STOP) with the “Stand-by all” func- Table 3

tion active, use terminal no. 5 and not no. 8 (see the FIXED RESISTOR STOP INPUT
“Stand-by all / Phototest connection” paragraph). FIRST device type
NO NC 8.2 kΩ
SECOND device

In parallel
NO [Note 2] In parallel
[Note 1]
type

In series
NC [Note 2] In series
[Note 3]
8.2 kΩ In parallel In series [Note 4]

8 – ENGLISH
Note 1 One or more NO devices can be connected in parallel 4.3 INITIAL START-UP AND ELECTRICAL
to one another without any quantity limitation with an 8.2 CONNECTIONS TEST
kΩ termination resistor (“Figure 12”). For electrical con- After powering the control unit, carry out the following checks:
nections with the “Stand-by all” function active, refer to 1. check that terminals “6-7” have roughly 30 VDC voltage
the “Stand-by all / Phototest connection” paragraph. (“Figure 16”). If the values do not match up, immediately
disconnect the power supply and carefully check the con-
m To connect ALT (STOP) with the “Stand-by all” func- nections and supply voltage.
tion active, use terminal no. 5 and not no. 8 (see the
“Stand-by all / Phototest connection” paragraph).
16

12 8 M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13

NO NO

8,2KΩ

9
2. after the quick initial flash, the “OK” LED will signal the
Note 2 Multiple devices can be connected as NO and NC con- correct operation of the control unit by flashing regularly
tacts in parallel, taking care to place a 8.2 kΩ resistor in every second. When there is a variation on the control unit
series with the NC contact (this also allows for combin- inputs, the “OK” LED will emit a quick double flash to sig-
ing 3 devices: NO, NC and 8.2 kΩ (“Figure 13”). nal that the input has been recognised
3. if the connections have been made correctly the “NC”-
type inputs must have the corresponding LED lit, while the
13 8 “NO”-type inputs must have the corresponding LED off
NC (refer to “Figure 17“ and to “Table 4”).

NO 8,2KΩ 17
L10 L12

OK L9 L11 L13
9

Note 3 One or more NC-type devices can be connected in se-

ries to one another and to an 8.2 kΩ resistor without any
quantity limitation (“Figure 14”).

14 8 Table 4
INPUT-LED MATCHES
Input Type of input LED status
NC NC 8,2KΩ L9 lit
ALT (STOP) NC
ALT (Only after point 5)
(STOP) 8.2 kΩ FIXED RESISTOR L9 lit
STOP (Only after point 5)
9
FOTO
NC L10 lit
(PHOTO)
Note 4 Only one device with 8.2 kΩ fixed resistor output can FOTO1
be connected; if needed, multiple devices must be con- NC L11 lit
(PHOTO1)
nected “in cascade” mode with a single 8.2 kΩ termina-
Sbs NO L12 off
tion resistor (“Figure 15”).
PARTIAL OPEN type 1 - NO L13 off
PARTIAL OPEN type 2 - NO L13 off
15 AUX OPEN ONLY - NO L13 off
1 2 n CLOSE ONLY - NO L13 off
8,2kΩ
PHOTO2 - NC L13 lit
8
9
Sensitive Sensitive Sensitive
edge edge edge

ENGLISH – 9
4. verify that, when intervening on the devices connected to SELECTING THE MOTOR TYPE
the inputs, the corresponding LEDs switch off or on Motor type Motor selector
5. verify that, when pressing the “[Stop/Set]” button and O 1 2 3 4
[Close q] (“Figure 18”) for over 3 seconds, both the mo- TOO4524 N

tors complete a brief opening manoeuvre with the upper

leaf motor starting first. Stop the manoeuvre by pressing O 1 2 3 4
the [Stop/Set] button. LED “L9” (“Figure 17”) must switch XME2024 N

on to signal the correct self-recognition.

18 4.5 AUTOMATIC LIMIT SWITCH SEARCH AND

“STOP” INPUT ACQUISITION
Once the checks have been completed, the automatic search
for mechanical stop devices connected to the control unit can
start. This operation is necessary, as the control unit must detect
the duration of the opening and closing manoeuvres. The proce-
dure is entirely automatic and consists in measuring the motor
effort to detect the mechanical stop devices during the opening
and closing phases.

m Before starting the limit switch search, check that

all the safety devices give their consent (STOP,
PHOTO and PHOTO1 enabled). The intervention of
l If the motors do not start for the opening manoeu- a safety device or the arrival of a command during
vre, invert the polarity of the motor cables. If the
first motor to move is not the one associated with the procedure causes its immediate interruption.
the upper leaf, invert M1 with M2. The leaves MUST be positioned roughly halfway
along their path.
a If any one of these tests fails, disconnect the pow-
er supply to the control unit and check the various 20
electrical connections made previously.

4.4 MOTOR SELECTOR

The control unit is equipped with a selector (A - “Figure 19”) that
allows for specifying which type of motor to use (see “Table 5”).

19
Press [Stop/Set] and [Close q] (“Figure 20”) for over 3 sec-
onds to start the automatic search phase.

The procedure entails:

–– control and memorisation of the motor selector
–– control and memorisation of the ALT input (NC / 8.2 kΩ)
–– brief opening of both motors
A –– closing of the lower leaf motor up to the mechanical stop for
the closing phase
–– closing of the upper leaf motor up to the mechanical stop for
the closing phase
–– start of upper leaf motor opening
m Any configuration not appearing in “Table 5” is not –– after the programmed offset, start of the lower leaf opening
movement
allowed.
–– the control unit will measure the movement required so that
Table 5 the motors can reach the mechanical stops for the opening
SELECTING THE MOTOR TYPE phase
Motor type Motor selector
–– the control unit runs the complete closing manoeuvre. The
motors can start at different times. The aim is to have a stag-
Generic
O
N
1 2 3 4
gered closing of the leaves so as to avoid potential shearing
between the leaves
O 1 2 3 4 –– end of the procedure with memorisation of all the measure-
WG2024 N
ments recorded.

WG3524
O 1 2 3 4 m All these phases occur one after the other, without
any intervention by the operator.
N

1 2 3 4
WG4024
O
N
m If, for any reason, the procedure fails to advance
correctly, it must be interrupted by pressing the
O 1 2 3 4 [Stop/Set] button. The procedure must then be re-
WG5024
N
peated (if necessary, by modifying the parameters,
for example the amperometric device thresholds
1 2 3 4
and the leaf delay – consult the “PROGRAMMING”
O
TOO3024 N

chapter).

l This procedure can be repeated without having to

delete the memory.
10 – ENGLISH
 5.2 COMMISSIONING
5 TESTING AND COMMISSIONING
a Commissioning can only be performed after all test-
These are the most important phases of the automation’s con- ing phases have been successfully completed.
5 TESTING AND COMMISSIONING

struction, as they ensure maximum safety of the system. The

test can also be used to periodically verify the devices making
up the automation.
a Before commissioning the automation, ensure that
the owner is properly informed of all residual risks
Testing and commissioning of the automation must be per-
and hazards.
formed by skilled and qualified personnel, who are responsible
for the tests required to verify the solutions adopted according To commission the automation:
to the risks present, and for ensuring that all legal provisions, 1. compile the automation’s technical file, which must in-
standards and regulations are met, in particular all the require- clude the following documents: overall drawing of the
ments of the EN 12445 standard, which defines the test meth- automation, wiring diagram, risk assessment and relative
ods for checking gate automations. solutions adopted, the manufacturer’s declaration of con-
The additional devices must undergo specific testing, both in formity for all devices used and the declaration of con-
terms of their functions and their proper interaction with the con- formity compiled by the installer
trol unit. Refer to the instruction manuals of the individual devic- 2. affix a data plate on the gate specifying at least the fol-
es. lowing data: type of automation, name and address of
the manufacturer (responsible for commissioning), serial
5.1 TESTING number, year of manufacture and CE mark
3. compile the declaration of conformity of the automation
The sequence of steps to be performed when running the test- and hand it to the owner of the automation
ing phase, as described below, refers to a typical system (“Fig- 4. compile the User Manual of the automation and hand it to
ure 3”). the owner of the automation
To run the test: 5. compile and provide the owner with the automation’s
1. check that the activation of the STEP-BY-STEP (Sbs) input “Maintenance schedule”, containing the maintenance in-
triggers the “Open, Stop, Close, Stop” sequence structions for all the automation’s devices.
2. check that the activation of the AUX input (Type 1 partial
opening function) manages the “Open, Stop, Close, Stop” l For all the above-mentioned documentation, Nice –
sequence only for the upper leaf motor. The lower leaf mo- through its technical assistance service – provides
tor must remain still during the closing phase the following: pre-completed forms.
3. start an opening manoeuvre and verify that:
–– when engaging FOTO (PHOTO) the gate continues the
opening manoeuvre
–– when engaging FOTO1 (PHOTO1) the manoeuvre 6 PROGRAMMING
stops until FOTO1 is disengaged. Subsequently, the
There are 4 buttons on the control unit: [Open p], [Stop/Set],
6 PROGRAMMING

manoeuvre will resume the opening movement

–– with FOTO2 (PHOTO2), after engaging this device, the [Close q] and [Radio R] (“Figure 21”), which can be used
manoeuvre must stop and restart during the closing both for commanding the control unit during the testing phases
phase and for programming the available functions.
4. verify that when the leaf reaches the mechanical stop for
the opening phase, the motors switch off 21 L1 .. L8
5. start a closing manoeuvre and verify that:
–– when engaging FOTO, the manoeuvre stops and re-
starts during the opening phase
–– when engaging FOTO1 (PHOTO1) the manoeuvre
stops until FOTO1 is disengaged. Subsequently, the
manoeuvre will resume the opening movement
–– when engaging FOTO2, the gate continues the closing
manoeuvre
6. verify that the stoppage devices connected to the STOP
input cause the immediate stoppage of any movement un-
der way and a brief reversal LR
7. check that the level of the obstacle detection system is
suited to the application: during the manoeuvre, during
The programmable functions available are arranged on two lev-
both the opening and closing phases, prevent the leaf’s
els and their operating status is signalled by the eight LEDs “L1
movement by simulating an obstacle and verify that the
... L8” and by the “LR” LED present on the control unit (LED lit =
manoeuvre reverses before exceeding the force specified
function active; LED off = function not active).
in the regulations
8. other checks can be necessary depending on the devices
connected to the inputs. 6.1 USING THE PROGRAMMING BUTTONS
[Open p]:
a If an obstacle is detected for two consecutive ma- –– Button for commanding the gate opening
noeuvres in the same direction, the control unit will –– Selection button during the programming phase.
perform a partial reversal of both motors for one
second only. After the next command is given, the [Stop/Set]:
leaves will start opening and the first intervention of –– Button used to stop a manoeuvre
the amperometric device for each motor will be re- –– If pressed for more than 5 seconds, it allows for entering the
garded as a mechanical stop for the opening phase. programming mode.
The same behaviour occurs when the mains power
supply is restored: the first command is always an [Close q]
opening command and the first obstacle is always –– Button for commanding the gate’s closure
regarded as a mechanical stop for the opening –– Selection button during the programming phase.
phase.

ENGLISH – 11
6.2 PRE-SET FUNCTIONS Table 6
The control unit has a few programmable functions, which are PRE-SET FUNCTIONS
pre-set in a typical configuration that suits most automations (see Function Pre-set value
“Table 6”). The functions can be modified at any time, both be- Automatic closing active
fore and after the automatic limit switch search phase, through
Condominium disabled
appropriate programming procedures described below.
Pre-flashing disabled
Close after photo disabled
Opening delay level 5 (20%)
Stand-by all / Phototest Stand-by all
Electric lock / OGI Electric lock
ALT (STOP) input self-recognition NC / 8.2 kΩ
Heavy gates disabled
Pause time 30 seconds
Type 1 partial opening (activates
Auxiliary input
upper leaf motor only)
Amperometric sensitivity level 3

6.3 LEVEL 1 PROGRAMMING (ON-OFF)

All the Level 1 functions are set by default to “OFF” and can be modified at any time. Refer to “Table 7” to check the various func-
tions.

6.3.1 Level 1 programming procedure

m The user has maximum 10 seconds to press the buttons consecutively during the programming procedure,
after which time the procedure terminates automatically and memorises the changes made up to then.
To perform Level 1 programming:
1. press and hold the [Stop/Set] button until LED “L1” starts flashing
2. press the [Open p] or [Close q] button to move the flashing LED to the LED associated with the function to be modified
3. press the [Stop/Set] button to change the status of the function:
–– short flash = OFF
–– long flash = ON
4. wait 10 seconds (maximum time) to exit the programming mode.

l To set other functions to “ON” or “OFF”, while the procedure is running, repeat points 2 and 3 during the phase
itself.

Table 7
LEVEL 1 FUNCTIONS (ON-OFF)
LED Function Description
Function ENABLED: after an opening manoeuvre there is a pause (equal to the set pause time), after
which the control unit automatically starts a closing manoeuvre. The pause time is set by default to 30
L1 Automatic closing
seconds. Pressing the [Stop/Set] button or the intervention of the “STOP” input stop the cycle.
Function NOT ENABLED: the system works in “semi-automatic” mode.
Function ENABLED: if the photocells intervene during the opening or closing manoeuvre, the pause
time drops to 4 seconds regardless of the set “pause time”. With “automatic closing” deactivated, if the
L2 Close after photo
photocells intervene during the opening or closing manoeuvre, the “automatic closing” activates with a
4-second “pause time”.
Function ENABLED: in the event of a blackout, even of short duration, 10 seconds after the electricity
L3 Always Close is restored the control unit detects that the gate is open and automatically starts a closing manoeuvre,
preceded by 5 seconds of pre-flashing.
Function ENABLED: phototest.
Instead of the “Stand-by all” function, the user can activate the “Phototest” function, which verifies
whether the photocells function properly at the start of a manoeuvre. To use this function, the connect the
photocells correctly (see “Figure 7 C”) then activate the function.
Function NOT ENABLED: stand-by.
Stand-by /
L4 The control unit has the “Stand-by all” function set by default; if it is active, 1 minute after the end of the
Phototest
manoeuvre the control unit switches off the “Stand-by all” function (terminal 5), all the inputs and the other
outputs to limit consumption (see “Figure 7 A”). This function is mandatory if the control unit is powered
exclusively through Solemyo photovoltaic panels. It is recommended even if the control unit is powered
from the mains and the user wishes to increase the emergency mode operation with the PS124 back-up
battery.

12 – ENGLISH
LEVEL 1 FUNCTIONS (ON-OFF)
LED Function Description
Function ENABLED: OGI (Open Gate Indicator).
Electric lock /
If the function is enabled, terminals 3-4 can be used to connect an open gate indicator light (24 V).
L5 OGI (Open Gate
Function NOT ENABLED: electric lock.
Indicator)
If the function is not enabled, terminals 3-4 can be used to connect the electric lock.
Function ENABLED: the warning light starts flashing 3 seconds before the start of the manoeuvre to
L6 Pre-flashing signal in advance a dangerous situation.
Function NOT ENABLED: the warning light starts flashing when the manoeuvre starts.
Function ENABLED: each command received triggers an opening manoeuvre that cannot be interrupted
Condominium by subsequent command impulses.
L7
function Function NOT ENABLED: each command received triggers an OPEN-STOP-CLOSE-STOP sequence,
which is useful when many people use the automation with radio commands.
Function ENABLED: if the function is enabled, the control unit can be configured to control heavy gates
by setting the acceleration ramp and closing slowdown speeds differently.
L8 Light/Heavy Gates
Function NOT ENABLED: if the function has not been enabled, the control unit is set for controlling light
gates.

6.4 LEVEL 2 PROGRAMMING (ADJUSTABLE PARAMETERS)

All Level 2 parameters are set by default as shown under “GREY” in “Table 8” and can be modified at any time. The parameters
can be adjusted to a value between 1 and 8. To check the value corresponding to each LED, refer to “Table 8”.

6.4.1 Level 2 programming procedure

m The user has maximum 10 seconds to press the buttons consecutively during the programming procedure,
after which time the procedure terminates automatically and memorises the changes made up to then.
To perform Level 2 programming:
1. press and hold the [Stop/Set] button until LED “L1” starts flashing
2. press the [Open p] or [Close q] button to move the flashing LED to the “entry LED” associated with the parameter to be
modified
3. press and hold the [Stop/Set] button. With the [Stop/Set] button pressed:
–– wait roughly 3 seconds, until the LED representing the current level of the parameter to be modified lights up
–– press the [Open p] or [Close q] button to shift the LED associated with the parameter’s value
4. release the [Stop/Set] button
5. wait 10 seconds (maximum time) to exit the programming mode.

l To set multiple parameters during the procedure's execution, repeat the operations from point 2 to point 4 dur-
ing the phase itself.

l The set value highlighted in grey (“Table 8”) indicates that is the default value.
Table 8
LEVEL 2 FUNCTIONS (ADJUSTABLE PARAMETERS)
Entry LED
Parameter Set value Description
LED (level)
L1 5 seconds
L2 15 seconds
L3 30 seconds
L4 45 seconds Adjusts the pause time, in other words, the time that elapses before
L1 Pause Time automatic re-closure. It is only effective if the Close function is
L5 60 seconds enabled.
L6 80 seconds
L7 120 seconds
L8 180 seconds

ENGLISH – 13
LEVEL 2 FUNCTIONS (ADJUSTABLE PARAMETERS)
Entry LED
Parameter Set value Description
LED (level)
L1 Type 1 partial open The control unit has an auxiliary input that can be configured with
L2 Type 2 partial open one of the following 6 functions.
Type 1 partial opening: performs the same function as the STEP-
L3 Open only
BY-STEP input, triggering the opening of the upper leaf only. It
L4 Close only only works with the gate fully closed, otherwise the command is
L5 Photo 2 interpreted as if it were a STEP-BY-STEP command.
L6 Stop (stops the manoeuvre) Type 2 partial opening: performs the same function as the STEP-
L7 Excluded BY-STEP input, triggering the opening of the two leaves for half the
L2 AUX input time it takes for full opening. It only works with the gate fully closed,
otherwise the command is interpreted as if it were a STEP-BY-STEP
command.
Open Only: this input performs opening only with the Open-Stop-
L8 Excluded Open-Stop sequence.
Close Only: this input performs closing only with the Close-Stop-
Close-Stop sequence.
Photo 2: performs the function of the “PHOTO 2” safety device.
Excluded: this input does not manage any function.
L1 Open: 40%; Close: 40%
L2 Open: 60%; Close: 40%
L3 Open: 80%; Close: 40%
L4 Open: 80%; Close: 60%
L3 Motor speed Adjusts the motor speed during normal travel.
L5 Open: 80%; Close: 80%
L6 Open: 100%; Close: 60%
L7 Open: 100%; Close: 80%
L8 Open: 100%; Close: 100%
L1 No discharge
L2 0.2 seconds
L3 0.4 seconds
Motor L4 0.6 seconds Adjusts the duration of the “brief reversal” of both motors, after
L4 discharge after completing the closing manoeuvre, to reduce the residual final
closing L5 0.8 seconds thrust.
L6 1.0 seconds
L7 1.2 seconds
L8 1.4 seconds
L1 Level 1 - Minimum force Adjusts the force of both motors.
L2 Level 2 - ... The control unit features a system that measures the current
absorbed by the two motors and used to detect the mechanical
L3 Level 3 - ...
limit switches and any obstacles during the gate’s movement. As
L4 Level 4 - ... the absorbed current depends on variable conditions (weight of the
L5 Level 5 - ... gate, sources of friction, wind gusts, voltage fluctuations, etc.), the
L6 Level 6 - ... intervention threshold can be modified. There are 8 levels: level 1
Motor force L7 Level 7 - ... is the most sensitive level (minimum force), while level 8 is the least
L5 (amperometric sensitive (maximum force).
sensitivity) Increasing the degree of amperometric sensitivity increases the
slowdown speed during the gate closing manoeuvre.
WARNING! – The suitably adjusted “amperometric” function
L8 Level 8 - Maximum force (together with other indispensable arrangements) can be
useful to ensure compliance with the EN 12453 and EN 12445
standards, which require the use of techniques or devices that
limit the force and dangerousness associated with automatic
door and gate movements.
L1 0%
L2 5%
L3 10%
L4 15% Adjust the closing delay for the upper leaf motor.
L6 Leaf delay It is programmed as a percentage of the work time.
L5 20% The opening delay is half the time of the closing delay.
L6 30%
L7 40%
L8 50%

14 – ENGLISH
LEVEL 2 FUNCTIONS (ADJUSTABLE PARAMETERS)
Entry LED
Parameter Set value Description
LED (level)
L1 500
L2 1000
L3 1500
L4 2500 Adjusts the number of manoeuvres after which
Maintenance
L7 the automation maintenance request is triggered
notification L5 5000 (see the “Maintenance notification” paragraph).
L6 10000
L7 15000
L8 20000
L1 Result of 1st manoeuvre (most recent)
L2 Result of 2nd manoeuvre
L3 Result of 3rd manoeuvre
L4 Result of 4th manoeuvre Allows for verifying the type of anomaly that
List of
L8 occurred in the last 8 manoeuvres (see “Anomaly
malfunctions L5 Result of 5th manoeuvre log” paragraph).
L6 Result of 6th manoeuvre
L7 Result of 7th manoeuvre
L8 Result of 8th manoeuvre

6.5 MEMORY DELETION 6.6.1.1 STANDARD memorisation (Mode 1: all buttons)

Procedures of this kind allow for simultaneously memorising,
m The procedure described below restores the con- during their execution, all the buttons on the transmitter. The
trol unit’s default settings. All the custom settings system automatically associates each button with a pre-defined
will be lost. command, according to the following scheme:
Table 9
TRANSMITTER FUNCTION PAIRINGS
22
L1 .. L8 Command Button
1 - Step-by-Step Will be paired with button 1
2 - AUX Will be paired with button 2
3 - OPEN Will be paired with button 3
will be paired with button 4 (if
4 - CLOSE
present on the transmitter).

6.6.1.2 CUSTOM memorisation (Mode 2: one button

only)
To delete the control unit’s memory and restore all the default Procedures of this kind allow for memorising, during their exe-
settings, proceed as described below: cution, a single button among those present on the transmitter.
1. press and hold the [Open p] and [Close q] buttons until The following commands can be paired with the buttons: Step-
the programming LEDs “L1-L8” light up (after roughly 3 by-Step, AUX, OPEN, CLOSE.
seconds) The installer decides which button to associate with the com-
2. release the buttons mand on the basis of the automation’s needs.
3. if the operation was successful, the programming LEDs
“L1-L8” flash quickly for 3 seconds. 6.6.2 Number of transmitters that can be memorised
The control unit’s receiver has 100 memory locations. A location
l The following features will be deleted: STOP config- can memorise either a single transmitter (i.e. the combination of
uration, limit switch positions, Level 1 and Level 2 its buttons and commands) or a single button with the relative
programming, number of manoeuvres. The memo- command.
rised transmitters will not be deleted.
6.6.3 Transmitter memorisation and deletion procedures
6.6 MEMORISING THE TRANSMITTERS
The control unit incorporates a radio receiver compatible with all a To perform the procedures A, B, C and D described
transmitters that adopt the following NICE radio encoding proto- below, the control unit’s memory must be unlocked.
cols: FLO, FLOR, O-CODE and SMILO. If the memory is locked, perform the unlocking pro-
cedure described in the “LOCKING AND UNLOCK-
ING THE MEMORY” paragraph
6.6.1 Procedure for memorising transmitter buttons
Among the available procedures for memorising transmitters,
some allow for memorising in “standard” mode (or Mode 1) and
others in “custom” mode (or Mode 2).

ENGLISH – 15
 6.6.3.3 PROCEDURE C - Memorising a transmitter by
23 means of another transmitter already memorised
(memorisation far from the control unit)
This procedure can be used to memorise a new transmitter by
means of a second transmitter, already memorised in the same
control unit. In this way, the new transmitter can receive the
LR same settings as those of the memorised transmitter. The user
does not have to intervene directly on the control unit’s [Radio
R] button, as the procedure is simply carried out within the
control unit’s radius of reception.
To perform this procedure:
6.6.3.1 PROCEDURE A - Memorising ALL buttons of a 1. on the transmitter to be memorised: press and hold the
single transmitter (STANDARD mode or Mode 1) button to be memorised
To perform this procedure: 2. on the control unit: after a few seconds (roughly 5) the
1. on the control unit: press and hold the [Radio R] but- “LR” LED lights up
ton until the “LR” LED lights up 3. release the transmitter button
2. release the button [Radio R] 4. on the transmitter already memorised: press and slowly
3. (within 10 seconds) on the transmitter to be memorised: release 3 times the memorised button to be copied
press and hold any button and wait until the “LR” LED 5. on the transmitter to be memorised: press and hold the
emits 3 long flashes (= memorisation completed correctly) same button pressed at point 1 and wait for the “LR” LED
4. release the transmitter button. to emit 3 long flashes (= memorisation completed correct-
ly)
l After the 3 long flashes a further 10 seconds remain 6. release the transmitter button.
to memorise an additional transmitter (if desired),
starting from step 3. l The “LR” LED can also emit the following signals: 1
fast flash, if the transmitter is already memorised, 6
flashes, if the transmitter’s radio encoding system
l The “LR” LED can also emit the following signals: 1 is not compatible with that of the control unit’s re-
fast flash, if the transmitter is already memorised, 6 ceiver, or 8 flashes, if the memory is full.
flashes, if the transmitter’s radio encoding system
is not compatible with that of the control unit’s re-
ceiver, or 8 flashes, if the memory is full. 6.6.3.4 PROCEDURE D - Deleting a single transmitter
(if memorised in Mode 1) or a single transmitter
button (if memorised in Mode 2)
6.6.3.2 PROCEDURE B - Memorising a SINGLE BUTTON
To perform this procedure:
of a transmitter (CUSTOM mode or Mode 2)
1. on the control unit: press and hold the [Radio R] but-
To perform this procedure: ton
1. choose the command to be paired with the relevant button 2. after roughly 4 seconds, the “LR” LED will light up steady
to be memorised: (continue holding down the [Radio R] button
–– for no. 1 - “Step-by-Step” press the [Radio R] button 3. on the transmitter to be deleted from the memory:
once press and hold a button (*) until the “LR” LED (on the con-
–– for no. 2 - “AUX” press the [Radio R] button twice trol unit) emits 5 fast flashes (or 1 flash if the transmitter or
–– for no. 3 - “OPEN” press the [Radio R] button 3 button is not memorised).
times 4. release the [Radio R] button.
–– for no. 4 - “CLOSE” press the [Radio R] button 4
times (*) If the transmitter is memorised in Mode 1, any button
2. on the control unit: press and release the [Radio R] can be pressed and the control unit will delete the en-
button for a number of times corresponding to the desired tire transmitter. If the transmitter is memorised in Mode
command, as shown near the command selected before- 2, it is necessary to press the memorised button to be
hand at step 1. deleted. To delete further buttons memorised in Mode 2,
3. (within 10 seconds) on the transmitter: press and hold repeat the entire procedure for every button to be delet-
the button to be memorised and wait for the “LR” LED to ed.
emit 3 long flashes (= memorisation completed correctly)
4. release the transmitter button. 6.6.3.5 PROCEDURE E - Deleting ALL memorised
transmitters
l After the 3 long flashes a further 10 seconds remain To perform this procedure:
to memorise an additional button (if desired), start-
ing from step 1. 1. on the control unit: press and hold the [Radio R] but-
ton
2. after roughly 4 seconds, the “LR” LED will light up steady
l The “LR” LED can also emit the following signals: 1 (continue holding down the [Radio R] button
fast flash, if the transmitter is already memorised, 6 3. after roughly 4 seconds, the “LR” LED will turn off (contin-
flashes, if the transmitter’s radio encoding system ue holding down the [Radio R] button
is not compatible with that of the control unit’s re- 4. when the “LR“ LED starts flashing, count 2 flashes and
ceiver, or 8 flashes, if the memory is full. prepare to release the button precisely during the 3rd
flash that follows
5. during the deletion process, the “LR” LED will flash rapidly
6. the “LR” LED will emit 5 long flashes to signal that the
deletion has been completed correctly.

16 – ENGLISH
6.7 LOCKING AND UNLOCKING THE MEMORY Procedure for locking/unlocking the memory:
1. disconnect the control unit from the power supply
a WARNING! - This procedure locks the memory, pre- 2. press and hold the [Radio R] button
venting the execution of Procedures A, B, C and D 3. power the control unit again (by pressing down the [Radio
described in the “Transmitter memorisation and de- R] button)
letion procedures“ paragraph 4. after 5 seconds the “LR” LED will emit 2 slow flashes
5. release the button [Radio R]
6. (within 5 seconds) repeatedly press the [Radio R] but-
24 ton to select one of the following options:
–– disabling of the memory lock function = LED off
–– enabling of the memory lock function = LED on
7. five seconds after last pressing the button, the “LR” LED
will emit 2 slow flashes to signal the end of the procedure.

LR

7 TROUBLESHOOTING...
(troubleshooting guide)
Some devices are configured for signalling the operating status or the presence of any anomalies.
7 TROUBLESHOOTING... (troubleshooting guide)

7.1 SIGNALLING THROUGH WARNING LIGHT

If a warning light is connected to the FLASH output on the con- 25
trol unit, the light will flash once every 1 second while the ma-
noeuvre is being performed. OK
If any anomalies occur, the warning light will emit slow flashes
repeated twice with a 1-second interval. “Table 10” describes 2 3 4 5 6 7 8 9 10 11 12 13
the cause and possible solutions for each type of anomaly sig-
nalled by the warning light.
In case of anomaly, the “OK” LED will also emit signals. “Table
10” describes the cause and possible solutions for each type of
anomaly signalled by the “OK” LED.

Table 10
SIGNALS EMITTED BY THE OK LED (“FIGURE 25”) AND WARNING LIGHT
Flashes Anomaly Possible solution
2 short red flashes
One or more photocells do not consent to the movement or have caused
1-second pause Intervention of a photocell
the latter to reverse. Check for any obstacles.
2 short red flashes
Intervention of the
3 short red flashes
“Obstacle Detection” During the gate’s movement, the motors encountered more resistance.
1-second pause
function through the force Verify the cause and increase the motor force if necessary.
3 short red flashes
limiter
4 short red flashes
Intervention of the ALT At the start of the manoeuvre or during the movement itself, the ALT (STOP)
1-second pause
(STOP) input input intervened. Identify the cause.
4 short red flashes
5 short red flashes Error in the internal Wait at least 30 seconds then try giving a command and disconnect the
1-second pause parameters of the control power supply if necessary. If the condition persists, there may be a serious
5 short red flashes unit malfunction and the electronic board needs to be replaced.
The maximum limit for
6 short red flashes
consecutive manoeuvres or Wait for a few minutes until the manoeuvre limiting device drops to under
1-second pause
manoeuvres per hour has the maximum limit.
6 short red flashes
been exceeded
7 short red flashes Wait at least 30 seconds then try giving a command and disconnect the
1-second pause Electric circuit anomaly power supply if necessary. If the condition persists, there may be a serious
7 short red flashes malfunction and the electronic board needs to be replaced.
8 short red flashes A command that prevents
Check the type of the “always present” command (for example, it could be
1-second pause other commands from being
a command from a clock on the AUX input).
8 short red flashes executed is already present

ENGLISH – 17
7.2 SIGNALS ON THE CONTROL UNIT
The control unit has LEDs “L1-L8” on the buttons and LEDs “L9- 26
L13” and the “OK” LED on the control unit terminals (“Figure L10 L12
26”).
OK L9 L11 L13
Each of these LEDs can emit special signals, both during nor- 5 6 7 8 9 10 11 12 13

mal operation and in case of anomalies. “Table 11” and “Table

12” describe the cause and possible solution for every type of
anomaly.
L1 .. L8

Table 11
SIGNALS OF THE LED ON THE CONTROL UNIT TERMINALS
Status Meaning Possible solution
All LEDs
Check whether the control unit is powered: measure on terminals 6-7 a
voltage of roughly 30 VDC (or 24 VDC if battery-powered).
No LED is lit No power to the control unit
Check the 2 fuses; if the OK LED is also not lit nor flashes, there may be a
serious fault, therefore the control unit must be replaced.
OK LED
Make sure there is power supply; verify whether the fuses are blown; if
OFF Anomaly necessary, identify the reason for the failure then replace the fuses with
others of the same type
There is a serious anomaly; try switching off the control unit for a few
On Serious anomaly seconds; if the condition persists, it means there is a fault and the circuit
board needs to be replaced
1 flash per second All OK The control unit works normally
1 flash every 5 seconds All OK Control unit in stand-by mode
The status of the inputs has This is normal when there is a change affecting one of the inputs: OPEN,
2 quick flashes
changed STOP, intervention of the photocells, or when the radio transmitter is used
Series of flashes
separated by a one- Various This is the same signal as the one on the warning light (see “Table 10”)
second pause
STOP LED
Intervention of the ALT
OFF Check the devices connected to the STOP input
(STOP) input
On All OK STOP Input active
PHOTO LED
Intervention of the PHOTO
OFF Check the devices connected to the PHOTO input
input
On All OK PHOTO input active
PHOTO1 LED
Intervention of the PHOTO1
OFF Check the devices connected to the PHOTO1 input
input
On All OK PHOTO1 input active
Sbs LED
OFF All OK Sbs input not active
On Intervention of the Sbs input Normal if the device connected to the Sbs input is active
AUX LED
OFF All OK AUX input not active
Intervention of the AUX
On Normal if the device connected to the AUX input is active
input

18 – ENGLISH
 Table 12
SIGNALS OF THE LED ON THE CONTROL UNIT BUTTONS
Status Meaning
L1 LED
OFF During normal operation, it signals that the “Automatic closing” mode is not active
On During normal operation, it signals that the “Automatic closing” mode is active
Flashes Function programming in progress
L2 LED
OFF During normal operation, it signals that the “Close after photo” mode is not active
On During normal operation, it signals that the “Close after photo” mode is active
Flashes Function programming in progress
L3 LED
OFF During normal operation, it signals that the “Always Close” mode is not active
On During normal operation, it signals that the “Always Close” mode is active
Function programming in progress. If it flashes together with LED L4, the position recognition phase must be carried out
Flashes
(see the “Automatic limit switch search and “STOP” input acquisition” paragraph)
LED L4
OFF During normal operation, it signals that the “Stand-by” mode is active
On During normal operation, it signals that the “Phototest” mode is active
Function programming in progress. If it flashes together with LED L3, the position recognition phase must be carried out
Flashes
(see the “Automatic limit switch search and “STOP” input acquisition” paragraph)
LED L5
OFF During normal operation, it signals the OGI output as OGI (open gate indicator)
On During normal operation, it signals the OGI output as ELS (electric lock)
Flashes Function programming in progress
LED L6
OFF During normal operation it signals that the “Pre-flashing” mode is not active
On During normal operation it signals that the “Pre-flashing” mode is active
Flashes Function programming in progress
LED L7
OFF During normal operation, it signals that the “Condominium” mode is not active
On During normal operation, it signals that the “Condominium” mode is active
Flashes Function programming in progress
LED L8
OFF During normal operation, it signals that the “Light gates” mode is active
On During normal operation, it signals that the “Heavy gates” mode is active
Flashes Function programming in progress

7.3 MAINTENANCE NOTIFICATION

The control unit allows for notifying the user when to perform 27 L1
maintenance on the automation. The signal is emitted once the
number of manoeuvres completed equals the value set for the
“Maintenance warning” adjustable parameter (see the “Table 8”
paragraph).
The maintenance request signal is emitted through the FLASH
warning light.
The FLASH warning light and the maintenance indicator emit the
signals indicated in “Table 13” based on the number of manoeu-
vres completed with respect to the set limit.
Table 13
L8
MAINTENANCE SIGNALS
Number of ma- Signal on mainte-
noeuvres
Signal on “Flash”
nance indicator To check the list of anomalies:
1. press and hold the [Stop/Set] button for roughly 3 sec-
Below 80% of Normal (0.5 s on, 0.5 s On for 2 s at the
start of opening
onds
the limit off)
2. release the [Stop/Set] button when the “L1” LED starts
At the start of the flashing
Between 81% Flashes
manoeuvre, it remains 3. press and release the [Open p] or [Close q] button to
and 100% of the throughout the
lit for 2 s then continues
limit manoeuvre shift flashing of the LED to “L8” (“Anomaly list” parameter)
normally
4. keep the [Stop/Set] button pressed down (it must be kept
At the start and end of pressed throughout phases 5 and 6)
Over 100% of the manoeuvre, remains 5. wait roughly 3 seconds, after which LED “L1” – corre-
Flashes always
the limit lit for 2 s then continues sponding to the outcome of the last manoeuvre – will light
normally
up
6. press and hold the [Open p] or [Close q] button to se-
7.4 ANOMALY LOG lect the desired manoeuvre: the corresponding LED will
emit the same number of flashes as those normally emit-
The control unit can display any anomalies that have occurred
ted by the warning light after an anomaly (see “Table 10”)
in the last 8 manoeuvres (for example, the interruption of a ma-
7. release the [Stop/Set] button.
noeuvre due to the intervention of a photocell or sensitive edge).
ENGLISH – 19
 2. place the interface (A) in the appropriate slot (B) on the
8 FURTHER INFORMATION
(Accessories) 3.
control unit’s electronic board
insert the cable (C) in the appropriate slot (D) on the in-
terface.
8 FURTHER INFORMATION (Accessories)

8.1 CONNECTING AN SM-TYPE RADIO RECEIVER

The control unit has a slot for mounting radio receivers with SM
29 A B
connector (optional accessories) belonging to the SMXI and
OXI families, which can be used to remotely control the control
unit through transmitters that intervene on the unit’s inputs.

f Before installing a receiver, disconnect the power

supply to the control unit.
To install a receiver (“Figure 28”):
1. remove the cover of the control unit’s containment box
2. insert the receiver (A) in the appropriate slot (B) on the
control unit’s electronic board
3. put the cover of the control unit’s containment box back
on. D C
At this stage, the control unit can be powered again.

At this stage, the control unit can be powered again.

28 B
l For further information, consult the specific manu-
A als of the connected devices.

8.3 CONNECTING THE PS124 BACK-UP BATTERY

The control unit is configured for being powered with PS124
back-up batteries that intervene in case of a power outage.

f Before installing a back-up battery, disconnect the

power supply to the control unit.
Before installing and connecting the back-up battery:
1. remove the cover of the control unit’s containment box
“Table 14” shows the receiver outputs and the control unit inputs 2. loosen the screw (A) and turn the panel (B)
associated with each.
Table 14 31
SMXI / SMXIS OR OXI / OXIFM / OXIT / OXITFM IN MODE 1 OR MODE
2
Receiver output Control unit input
Output No. 1 Step-by-Step
Output No. 2 AUX (pre-set value: Partial open 1)
Output No. 3 “Open Only”
Output No. 4 “Close Only” A B

l For further information, consult the specific manual

of the receiver.

8.2 CONNECTING THE IBT4N INTERFACE

The control unit is equipped with a “IBT4N”-type connector for
the IBT4N interface, which allows for connecting all devices
equipped with BusT4 interface, such as, for example, Oview
programmers and the IT4WIFI Wi-Fi interface.
The Oview programmer allows for comprehensively and rapidly
managing the installation, maintenance and diagnosis of the en-
tire automated system.

f Before connecting the interface, disconnect the

power supply to the control unit.
To install the interface (“Figure 29”):
1. remove the cover of the control unit’s containment box

20 – ENGLISH
3.
4.
position the battery (C)
insert the connector (D) through the opening (E) and con-
a The “Solemyo” system can only be used if the
“Stand-by all” function is enabled (ON) on the con-
nect it to the slot (F) trol unit and if the connections are made as shown
5. close the panel (B) in the diagram (A) in “Figure 7”.

9
30
PRODUCT MAINTENANCE
C Being an electronic part, the control unit does not require any
9 PRODUCT MAINTENANCE

special maintenance. Nonetheless, the system should be reg-

ularly checked to ensure that it works efficiently at least every
6 months according to the instructions in the “TESTING AND
F COMMISSIONING” chapter.

D
10 PRODUCT DISPOSAL
10 PRODUCT DISPOSAL

B
l This product is an integral part of the operator and
must therefore be disposed of with it.
E
As with the installation, only qualified personnel must dismantle
the product at the end of its life.
This product is composed of different types of materials. Some
6. remove the pre-cut element (G) and insert the connector of these materials can be recycled; others must be disposed of.
(H) into the slot located under the pre-cut element Please enquire about the recycling or disposal systems in place
in your local area for this type of product.
31 a WARNING
Some parts of the product may contain polluting or
dangerous substances. If not disposed of correctly,
these substances may have a damaging effect on
the environment and human health.

l As indicated by the symbol shown

here, this product must not been
G disposed of with household
waste. Separate the waste for dis-
H posal and recycling, following the
methods stipulated by local reg-
ulations, or return the product to
the seller when purchasing a new
product.

a WARNING
Local regulations may impose heavy penalties if
7. put the cover of the control unit’s containment box back this product is not disposed of in compliance with
on. the law.
At this stage, the control unit can be powered again.

8.4 CONNECTING THE SOLEMYO SYSTEM

The control unit is configured for being powered with the “Sole-
myo” photovoltaic system (photovoltaic panel and 24 V battery).
To connect the Solemyo battery to the control unit, remove the
pre-cut element (A) and use the same connector normally used
for the back-up battery.

32

a When the automation is powered through the “Sole-

myo” system, IT MUST NOT BE POWERED through
the mains electricity at the same time.

ENGLISH – 21
 11 TECHNICAL SPECIFICATIONS
11 TECHNICAL SPECIFICATIONS

l All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). Nice S.p.A.
reserves the right to apply modifications to the product at any time when deemed necessary, without altering
its functions and intended use.

Table 15
TECHNICAL SPECIFICATIONS
Description Technical specification
Control unit MC424L: 230 Va ± 10% 50–60 Hz; fuse: 1A type T
Mains power supply Control unit MC424L/V1: 120 Va ± 10% 50–60 Hz; fuse: 2A type T
Control unit MC424L/AU01: 250 Va ± 10% 50–60 Hz; fuse: 1A type T
Maximum power input 170 W
Emergency power supply configured for PS124 back-up batteries and for the Solemyo solar power kit
Maximum motor current 3 A (with “level 6” amperometric device intervention)
Services power output 24 Vc maximum current 200 mA (the voltage may vary between 16 V and 33 Vc)
Phototest output 24 Vc maximum current 100 mA (the voltage may vary between 16 V and 33 Vc)
for 24 V c warning lights, maximum power 25 W (the voltage may vary between 16 V and 33 Vc);
Warning light output
for Nice ELDC and EL24 warning lights
for 24 V c lamps, maximum power 5 W (the voltage may vary between 16 V and 33 V c) or for 12 V
Electric lock output
a electric locks, 15 VA
ALT (STOP) input for NC contacts or 8.2 kΩ fixed resistor +/– 25%
Work time measured automatically
Pause time settable
Discharge time settable
Leaf opening delay settable
Leaf closing delay measured automatically
for WINGO motors (WG2024, WG3524, WG4024, WG5024), TOO (TOO3024, TOO4524), SFAB
1st motor output
(XME2024)
for WINGO motors (WG2024, WG3524, WG4024, WG5024), TOO (TOO3024, TOO4524), SFAB
2nd motor output
(XME2024)
power supply: 30 m
Solemyo solar kit power supply: 3 m
motors: 10 m
other inputs/outputs: 30 m
Max length of cables
warning light: 10 m
OGI: 30 m
electric lock: 10 m
antenna: 20 m (recommended below 3 m)
Radio receiver “SM”-type connector for SMXI, SMXIS, OXI receivers (Mode 1 and Mode 2)
Operating temperature from –20°C to +55°C
Protection rating IP 54 (with container intact)
Dimensions (mm) 310 x 232 x H 122
Weight (kg) 4,1

12 CONFORMITY
12 CONFORMITY

EU Declaration of Conformity
and declaration of incorporation of “partly completed machinery”
Note - The contents of this declaration correspond to declarations in the official document deposited at the registered offices of Nice S.p.a. and in particular to the last revision available before
printing this manual. The text herein has been re-edited for editorial purposes. A copy of the original declaration can be requested from Nice S.p.a. (TV) I.
Number: 296/MC424 Rev: 5 Language: EN
Manufacturer’s Name: Nice s.p.a.
Address: Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy
Authorized Person to constitute
technical documentation: Nice s.p.a.
Type of product: Comand central a 2 motor 24V dc
Model/Type: MC424, MC424L
Accessories: Refer to the catalog
The undersigned Roberto Griffa, in the role of Chief Executive Officer, declares under his sole responsibility that the product described above complies with the provisions
laid down in the following directives:
• Directive 2014/30/EU (EMC), according to the following harmonized standards: EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011
The product also complies with the following directives according to the requirements envisaged for “partly completed machinery” (Annex II, part 1, section B):
• Directive 2006/42/EC of the EUROPEAN PARLIAMENT AND COUNCIL of 17 May 2006 related to machinery and amending the Directive 95/16/EC (recast).
It is hereby stated that the relevant technical documentation has been compiled in accordance with annex VII B of Directive 2006/42/EC and that the following essential
requirements have been fulfilled: 1.1.1 - 1.1.2 - 1.1.3 - 1.2.1 - 1.2.6 - 1.5.1 - 1.5.2 - 1.5.5 - 1.5.6 - 1.5.7- 1.5.8 - 1.5.10 - 1.5.11
The manufacturer undertakes to transmit to the national authorities, in response to a reasoned request, the relevant information on the “ partly completed machinery “, while
maintaining full rights to the related intellectual property.
Should the “ partly completed machinery” be put into service in a European country with an official language other than that used in this declaration, the importer is obliged
to arrange for the relative translation to accompany this declaration.
The “partly completed machinery” must not be used until the final machine in which it is incorporated is in turn declared as compliant, if applicable, with the provisions of
directive 2006/42/EC.
Ing. Roberto Griffa
The product also complies with the following standards: (Chief Executive Officer)
EN 60335-1:2012+A11:2014, EN 62233:2008, EN 60335-2-103:2015

Oderzo, 05/09/2017

22 – ENGLISH
&
INSTRUCTIONS AND WARNINGS FOR THE USER

Before using the automation for the first time, ask the installer to Safety devices out of order: the automation can also be used
explain the origin of any residual risks and take a few minutes when one or more safety devices are defective or out of order.
to read this instruction manual and warnings for the user given The gate can be operated in the “Person present” mode in the
to you by the installer. Store the manual for future reference and following way:
hand it to the new owner when transferring the automation. 1. send a command to operate the gate, with a transmitter
or key selector, etc. If everything works properly, the gate
a WARNING! will move normally, otherwise proceed as described be-
Your automation is a machine that faithfully exe- low
2. within 3 seconds, press the control again and hold it down
cutes commands imparted by the user. Negligence
3. after roughly 2 seconds, the gate will move in the “Person
and improper use may lead to dangerous situations:
present” mode, in other words, it will continue moving so
–– do not manoeuvre the gate if there are people, animals long as the control is held down.
or objects within its range of operation
–– it is strictly forbidden to touch parts of the automation m If the safety devices are out of order, have the sys-
while the gate or door is moving tem repaired as soon as possible by a qualified
–– the photocells are not a safety device but only an aux- technician.
iliary aid to safety. They are built using highly reliable The test, periodic maintenance and any repairs must be docu-
technology but, in extreme conditions, may malfunction mented by the person carrying out the work and the documents
or even become defective. In certain cases, the defect must be stored by the owner of the automation. The only inter-
may not be clearly evident. For these reasons, it is im- ventions the user may carry out periodically include cleaning of
portant to follow all the instructions given in this manual the photocell glass components (use a soft and slightly damp
when using the automation cloth) and removing any leaves or stones that may obstruct the
–– periodically check that the photocells work properly. automation.
a IT IS STRICTLY FORBIDDEN to transit through the m The user of the automation must manually unlock
gate while it is closing! It is only possible to transit the motor before starting any maintenance opera-
through the gate when it is fully open and the leaves tion, to prevent other people from accidentally ma-
are at a standstill. noeuvring the gate (consult the respective instruc-
tion manual).
a CHILDREN Maintenance: in order to ensure constant levels of safety and
An automation system guarantees a high degree the longest useful life for the automation, routine maintenance
of safety. With its detection systems, it can control must be carried out (at least every 6 months).
and guarantee the gate’s movement in the presence
of people or objects. It is nonetheless advisable to l Only qualified personnel is authorised to carry out
forbid children from playing near the automation checks, maintenance operations and repairs.
and not to leave remote controls near them to pre- Disposal: at the end of its useful life, the automation must be
vent any unwanted activation of the system. The au- dismantled by qualified personnel and the materials must be
tomation is not a toy! recycled or disposed of in compliance with the local regulations
The product is not intended for use by persons, in- in force.
cluding children, with limited physical, sensory or l If the automation was locked using the “Lock auto-
mental capacities, or who lack experience or knowl- mation” command, the gate will not move when a
edge, unless supervised or trained in the use of the command is sent and the warning light will emit 9
product by a person responsible for their safety. short flashes.
Anomalies: if the automation appears to behave strangely,
disconnect the power supply to the automation and manually
unlock the motor (consult the respective instruction manual) to
manoeuvre the gate manually. Do not perform any repairs per-
sonally, but contact your trusted installer.

l Do not modify the system or the programming and

adjustment parameters of the control unit: your in-
staller is exclusively responsible for these opera-
tions.
Failure or power outage: while waiting for your installer to in-
tervene or the power supply to be restored, if the system is not
equipped with back-up batteries, the automation can be used
by manually unlocking the motor (consult the relative instruction
manual) and manually moving the gate leaf.
&

ENGLISH – 23
 &
NOTES

&

24 – ENGLISH
NOTES

ENGLISH – 25
 IDV0619A00EN_31-01-2019

Nice SpA
Via Pezza Alta, 13
31046 Oderzo TV Italy
[email protected] www.niceforyou.com