SKY Vehicle Tracking Alarm

CAT-3

COMMANDS

DATE:2009-12-8
Passwords Degree：

User password：UPWD ---- User password, “1234”

Center password：GPWD---- 1. Momitor center operation password “8888”

2．To restore the user's password when need

Supper password：XXXX---- To restore or change the center password when need

SMS Or
GPRS(TCP/IP)
Monitor
SMS
ing

User Operation Part

1．Setting-up

1.1 Recipient A.B.C

SMS: *UPWD*Axxxxxxxxxx*Bxxxxxxxxx*Cxxxxxxxx#
Reply: A:xxxxxxxx,B:xxxxxxxxx,C:xxxxxxxx;

1.2 Time Zone

SMS: *UPWD*GMT+/-xxxx# Reply: GMT +/-xxxx SETUP OK!

2. Basic Operation
2.1 Modify PASSWORD
SMS: *UPWD* EXXXX#
Reply: Password has been changed!

Note: >> xxxx refers new PASSWORD. It is constituted by 4 ASCII codes.

>> Factory default:1234.
2.2 Enforced power/oil off
Enforced –off SMS: *UPWD* STOP # Reply: Engine has be turned off!

Re-energize SMS: *UPWD* K # Reply: Engine can be started

2.3 Resume to Factory Default

SMS: *UPWD*V# Reply: Factory Default Restored!

Recipient: Non
Password: 1234
Time Zone: +/-0000
GEO alert: Off
Over speed Alert: Off

2.4 GEO range report: On/Off

On:
SMS: *PWD*SC:N/SXX.XXX,E/WXXX.XXX,XXXXX# Reply: GEO Report On / Format Error!

Note: >>N/S is lat. and E/W is the long. of the range center; format: degree

>> xxxxx choose 00300～50000; unit: metre

Exp: *1234*SC:N41.820,E123.392,00800#
>N41.820：north latitude of the range center point 41.820°. for exp:1° is 01.000
>E123.392：east longitude of the center point 123.392° . for exp: 1°is 001.000
> 00800: radius of the range is 800m (unit: metre)

Off:
SMS: *PWD*SC:00# Reply: GEO report off!

2.5 Over speed Alert On/Off

On: SMS: *UPWD* SPDxxx,ss# Reply: Over SPDxxx alert on!
Off: SMS: *UPWD * SPD000# Reply: Over SPD alert off !
Note: >> xxx: choose 020～999,
Min speed is 20Km/H; Max limited speed is 999 Km/h.
If xxx is less than 20， may not receive the “Over speed Alert” SMS
>> ss: 01~99min: indicate continuous overspeed statue, the interval to repor the alert.

2.6 Wrong Message

Reply: Invalid command, please confirm!

3. Query
3.1 Recipients Query
SMS: *UPWD*y# reply: A:xxxxxxxxxxxx B:XXXXXXC:XXXXXX

3.2 Status Query

SMS: *UPWD*x#
Reply: Power:on/off;LAC:xxxxxCID:xxxxx;Time:xx-xx-xx xx:xx:xxSpeed:xxxkm/h
S/N:xxdxxmxxs W/E:xxxdxxmxxs
3.3 GPS Data Query
A. GPS Data Query：（Format：Degree/ Minute/Second）
SMS: *UPWD*GPSM#
Reply: Time:xx-xx-xx xx:xx:xxSpeed:xxxkm/hS/N:xxdxxmxxsW/E:xxxdxxmxxs

B. GPS Data Query: ( Format: Degree)

SMS: *UPWD*GPSD#
Reply: Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h S/N:xx.xxxx W/E:xxx.xxxx

C. GPS Data with Google link Query

Send the SMS: *PWD*GPSW#
SMS reply: http://maps.google.com/maps?f=q&hl=en&q=(-)xx.xxxxxx,(-)xxx.xxxxxx&ie=UTF8&z=16&iwloc=addr&om=1

NOTE: GPS fails to position: query reply SMS reads: GPS invalid !

3.4 Vehicle Address Query (pre-download address date)

◘ By address memorizer
SMS: *UPWD*DP#
Reply: ■ Locate successfully, the reply SMS: Placename>direction>distance

■ Locate intermit(duration is within 50000sec), the reply availability date before:

XXXXX secends before Placename>direction>distance LAC:XXXXXCID:XXXXX

■ GPS invalid and duration is over 50000sec, the reply SMS:

No GPS! LAC:XXXXXCID:XXXXX

■ Location in place without memorized name(or the distance between the location and relative
memorized dot is over 50000 metres ), the reply SMS: No valid address!

◘ By Center Address Translator

SMS: *UPWD*DW# reply: Placename>direction>distance

4. ALERT Report
4.1 Emergency Alert (SOS) the SOS Aert is sent directly to the recipients A,B,C.
Highjack Alert; LAC:xxxxxCID:xxxxx; Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h S/N: xxdxxmxxs W/E: xxxdxxmxxs

4.2 Power-off Alert: Alert reports to Recipients A,B,C

Power off Alert; LAC:xxxxxCID:xxxxx; Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h S/N: xxdxxmxxs W/E: xxxdxxmxxs

4. 3 Over speed Alert: Alert reports to Recipients A

Overspeed Alert; LAC:xxxxxCID:xxxxx; Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h S/N: xxdxxmxxs W/E: xxxdxxmxxs

4.4 GEO Alert: Alert reports to Recipients A

GEO Alert; LAC:xxxxxCID:xxxxx; Time:xx-xx-xx xx:xx:xx Speed:xxxkm/h S/N: xxdxxmxxs W/E: xxxdxxmxxs
 MONITORING CENTER

1. Monitoring Center Setup

1.1 Setup recipients:
Command : *GPWD*Axxxxxxxxxx*Bxxxxxxxxx*Cxxxxxxxx#
SMS Reply: Armed/Unarmed; A:xxxxxxxx,B:xxxxxxxxx,C:xxxxxxxx;
GPRS Reply: IMEI:xxxxxxxxxxxxxxx# Armed/Unarmed; A:xxxxxxxx,B:xxxxxxxxx,C:xxxxxxxx;

Note: ▫ number: Max: 20 digit

▫ G:XXXX indicates the center number.
▫ D:XXXX indicates Address Translater number

1.2 Setup monitor center number:

Command: *GPWD*Gxxxxx#
SMS Reply: A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;
GPRS Reply: IMEI: xxxxxxxxxxxxxxx# A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;

1.3.Setup Address translator number:

Command: *GPWD*Dxxxxx#
SMS Reply: A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;
GPRS Reply: IMEI: xxxxxxxxxxxxxxx#A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;

1.4. Time Zone

Command: *GPWD*GMT+/-XXXX#
SMS Reply: GMT:+/-XXXX Set up OK!
GPRS Reply: IMEI: xxxxxxxxxxxxxxx# GMT:+/-XXXX Setup OK!

exp: East 8 zne (GMT+8:00): command: *GPWD*GMT+0800#

West 3:30 zone（GMT-3:30） command: *GPWD* GMT -0330#

2. Operations and Commands

2.1 Modify PASSWORD

To restore the user's password

Command: *GPWD*Exxxx# SMS Reply: Change User Password OK!
GPRS Reply: IMEI:xxxxxxxxx# Change User Password OK!

To change the monitor center password

Command：*GPWD*Fxxxx# SMS Reply: Change Center Password OK!

GPRS Reply: IMEI:xxxxxxxxx#Change Center Password OK!

2.2 Enforced off / Re-energize Engine:
Enforced –off:
Command: *GPWD* STOP # SMS Reply: Engine will be turned off !
GPRS Reply: IMEI:xxxxxxxxx#Engine will be turned off !

Enable engin on:

Command: *GPWD* K # SMS Reply: Relieve 'STOP' & Unarmed
GPRS Reply: IMEI:xxxxxxxxx# Relieve 'STOP' & Unarmed

2.3 Resume to Factory Default

Command: *GPWD*FAC# SMS Reply: Center Refactory ok !
GPRS Reply: IMEI:xxxxxxxxxxxxxxx#Center Refactory ok !

Note：After FAC command take effect

■ Monitor Center NumberG / address translation center number D : Cleared

■ IP address and port setup: Cleared
■ Automatic GPS data report: GS0000
■ Route Points Report: Off/ Cleared
■ Fixed distance: FD00000
■ GEO fence: Cleared
■ Over speed Alert to center: off

3. GPS Data Report Function

3.1 GPRS Configure/On: IP、COM port and APN / domain, port and APN / GPRS PWD and User name

■ When terminal is in use, it will automatically check the IP, the COM port and the APN. If all are available, it will
connect to the IP through TCP protocol, and then will automatically send an IMEI xxxxxxxxxxxxx (heart interval )to
the monitor center.
■ When the connection is cut off, it will re-connect to the IP.
■ If the IP is dynamic IP, or you have changed the IP and the COM port, you should via SMS command(or by USB
port ) to set up GPRS again, the GPRS connection will be cut off and restart to connect to new IP.

Command: *GPWD*GPRS:[NetAddr],[Port],[Interval],[APN],<UserName>,<UserPassword>#

SMS Reply: GPRS Activated! [NetAddr],Port], [Interval],[APN],<UserName>,<UserPassword>#

GPRS reply: IMEI: xxxxxxxxxxxxxxx#GPRS Activated! [NetAddr],[Port],[Interval],[APN],

<UserName>,<UserPassword>#

GPRS interval Reply: IMEI:xxxxxxxxxxxxx#

EXP: *ABCD*GPRS:60.17.90.168,5065,30,CMNET,tel25660,dgertd#

[Interval]: GPRS heart iterval. Unit: 1-99 minute. When Interval is ‘0’, truning off sending heart interval.
[NetAddr]: >> IP address of center, Maximum 30 digits (including three dots)
>> DN: domain name, Maximum 30 alphabets,
>> ":” is not allowed between the alphabets.

[Port]： COM port of center maximum 5-digits, less than:65535

[APN]： GSM Carrier name , 1-32 digits ASCII code

 <UserName> : user name if need
<UserPassword>: user password : empty if not need .

GPRS turn off and data report by SMS:

Command: *GPWD*GPRS:# SMS Reply: GPRS deactivated!

GPRS Reply: IMEI:xxxxxxxxx# GPRS deactivated!

3.2. GPS Periodical Report(real-time report) on/off

On:
Command: *GPWD*GS:XX,YY# SMS Reply: Auto report xxxx,yy
GPRS Reply: IMEI:xxxxxxxxx#Auto report xxxx, yy

Note：XX: Interval of report (01-99); unit: 20secs; when XX is 00 Auto report turn off

YY: times of report (00-99); when YY is 00, report times unlimited (continuously).

Example： Command： *8888*GS:60,10# Reply: Auto report 1200,10

60 refers to reporting interval is 1200secs : 60×20s= 1200secs

10 refers to reporting times is ten.

Off :
Command: *GPWD*GS:00,xx# SMS Reply: Auto report turn off!
GPRS Reply: IMEI:xxxxxxxxx#Auto report turn off!

3.3. Route-points Report: on/ off

On: Command: *GPWD*SD:01,N/SXX.XXX,E/WXXX.XXX,XXXXX;02…………#
SMS Reply: Route-points Report Activated !
GPRS Reply: IMEI:xxxxxxxxx#Route-points Report Activated !

Note: >>N/S is lat. and E/W is the long. of the route-point; format: degree
>> 01,02,03------10 (MAX: 10) indicates the number code of the route points.

Off: Command: *GPWD*SD:00#

SMS Reply: Route-points Report Deactivated !
GPRS Reply: IMEI:xxxxxxxxxxxxxxx#Route-points Report Deactivated !

3.4. Fixed Distance report: on/off

On: Command：*GPWD*FD:xxxxx# SMS Reply：FD:xxxxx Report on!

GPRS Reply: IMEI:xxxxxxxxxxx#FD:xxxxx Report on!

Note: xxxxx indicates the distance range. It ranges 00300-50000 meters.

Off: Command：*GPWD*FD:00000# SMS Reply：FD Report off !

 GPRS RePly: IMEI:xxxxxxxxx#FD Report off !

3.5. Over Speed report: on/ off (data set by center)

On: Command： *UPWD* SPDxxx,ss# SMS Reply: Over SPDxxx alert on!

GPRS Reply: IMEI:xxxxxxxxx#Over SPDxxx alert on!

Off: Command： *UPWD * SPD000# SMS Reply: Over SPD alert off !

GPRS Reply: IMEI:xxxxxxxxx#Over SPD alert off !

Note: >> xxx choose 020～999, Min speed is 20Km/H; Max limited speed is 999 Km/h.
>> If xxx is less than 20， may not receive the “Over speed Alert” SMS

3.6. Over GEO range report: on/off

On: Command: *GPWD*SC:N/SXX.XXX,E/WXXX.XXX,XXXXX#

SMS Reply: GEO Report On / Format Error!
GPRS RePly: IMEI:xxxxxxxxx#GEO Report On / Format Error!

Note: >>N/S is lat. and E/W is the long. of the range center; format: degree

>> xxxxx choose 00300～50000; unit: metre

Exp: command: *8888*SC:N41.820,E123.392,00800#

>> N41.820：north latitude of the range center point 41.820 degree. for exp:1° is 01.000

>> E123.392：east longitude of the center point 123.392 degree. for exp: 1°is 001.000

>> 00800: radius of the range is 800m (unit: metre)

Off: Command: *GPWD*SC:00# SMS Reply: GEO report off!

GPRS Reply: IMEI:xxxxxxxxx#GEO report off!

4. Query
Note: query by SMS, reply SMS; Query by GPRS, reply via GPRS.

4.1. Vehicle Status Query

Command: *GPWD*X#
Reply: IMEI:xxxxxxxxxxxxx#,00,00, X1X2X3, LAC:xxxxxCID:xxxxx,[GPRMC]#

4.2. IMEI Query

Command: *GPWD*IMEI#
Reply: IMEI:xxxxxxxxxxxxxxx#

4.3. GPRS Query

 Command: *GPWD*GPRS#
SMS Reply: GPRS:[NetAddr],[Port],[Interval],[APN],<UserName><,UserPassword>#
GPRS Reply: IMEI:xxxxxxxxx#GPRS:[NetAddr],[Port],[Interval],[APN],<UserName>,<UserPassword>#

4.4. Recipients of mobil-phone Number Query

Command: *GPWD*YY#
SMS Reply: A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;
GPRS Reply: IMEI:xxxxxxxxx# A:xxxxxxx,B:xxxxxxxx,C:xxxxxx,D:xxxxxxx,G:xxxxxxxxxx;

4.5. GPS Data query: （GPS Standard Format）

Command : *GPWD*GPS#
SMS Reply: IMEI:xxxxxxxxxxx#,00,00,X1X2X3,LAC:xxxxxCID:xxxxx,$GPRMCxxxxxxxx#
GPRS Reply: IMEI:xxxxxxxxxxx#,00,00,X1X2X3,LAC:xxxxxCID:xxxxx,$GPRMCxxxxxxxx#

4.6. Time Zone Query

Command: *GPWD*GMT +/-xxxx #
SMS REPLY: GMT: +/-xxxx SETUP OK!
GPRS Reply: IMEI:xxxxxxxxx#GMT:+/-xxxx SETUP OK!

4.7 Version Query

COMMAND: *GPWD*VER# SMS Reply: Ver:xxxxxxx
GPRS RePly: IMEI:xxxxxxxxx#Ver:xxxxxxx

5. Data Report to center

GPS data is sent to the monitoring center through GPRS when GPRS is connected.
GPS data is sent to the monitoring center through SMS when GPRS is disconnected.

Data standard format: IMEI:[EMEI],[TYPE],[PARAM], X1X2X3, LAC:[LAC] CID:[CID], [GPRMC]#

high lever: 1; low lever: 0
X1: Door: 1: close;
X2: ACC: 0: off
X3: Power: 1: on ; 0: off

Type Status Exp:

00 Unarmed [PARAM] invalid: 00

01 Armed [PARAM] invalid: 00

02 Door-open alert [PARAM] invalid: 00 IMEI:xxxxxxxxxx#,02,00,001,LAC:xxxxxCID:xxxxx,[GPRMC]#

Engine-on alert [PARAM] invalid: 00 IMEI:xxxxxxxxx#, 03, 00,111,LAC:xxxxxCID:xxxxx, [GPRMC]#

03
SOS(Hijack Alert) [PARAM] invalid: 00 IMEI:xxxxxxxxx#,04,00,101/0,LAC:xxxxxCID:xxxxx,[GPRMC]#
04
Power failure alert [PARAM] invalid: 00 MEI:xxxxxxxxx#,05,00,100,LAC:xxxxxCID:xxxxx,[GPRMC]#
05
GEO alarm [PARAM] invalid: 00 MEI:xxxxxxxxx#,06,00,101,LAC:xxxxxCID:xxxxx,[GPRMC]#
06
 Move alert [PARAM] invalid: 00
07
Real-time Report [PARAM] valid:
08 01~99: Reported times IMEI:xxxxxxxxx#,08,05,101,LAC:xxxxxCID:xxxxx,[GPRMC]#
00:unlimited times report

10 Over Speed Alert [PARAM] invalid: 00 IMEI:xxxxxxxxx#,10,00,101,LAC:xxxxxCID:xxxxx,[GPRMC]#

11 Route-points Report [PARAM] valid: IMEI:xxxxxxxxx#,11,08,101,LAC:xxxxxCID:xxxxx,[GPRMC]#

number of the passing point

12 Fixed Distance Report [PARAM] invalid: 00 IMEI:xxxxxxxxx#,12,00,101,LAC:xxxxxCID:xxxxx,[GPRMC]#

Geographical Address Translation Center

09
report date

Note: the content in shadow part for CAT-5/6