product data Waterproofing Products
OPTIMASTIC PU-W
WATER-BASED POLYURETHANE MEMBRANE
Product Description Processing Data
OPTIMASTIC PU-W is a ready to use flexible single Mix Ratio
pack cold applied waterproofing and sealing product Single Component
(by volume)
composed of water-based synthetic resins that exhibit Gel Time at 30 ºC 1 hour
excellent mechanical, thermal & natural element Coating Min. 2 hours
resistance properties. It provides a protective Interval Max. 12 hours
elastomeric membrane that has long-lasting durability Full Cured 8 hours
and absolute high performance waterproofing suitable Rain Stability Time 4 hours
for various type of roofs and outdoor areas. Pot Life 30-45 minutes
Shelf Life 12 months at room temperature
Features
Ease of application (roller or spray), Fast Drying
Available in variety of colors for decorative purposes Technical / Performance Data
(standard : white)
White other colors available
Coal tar free Colors
upon request
No blistering and No reinforcement required
>600-700%
Anti-fracture Elongation
ASTM D412
Resistant to UV
Shore 81.2
Non-Toxic Hardness
ASTM D 2240: 2016
Maintains thermal shock properties over (-50˚C to
90˚C) 3.53 Mpa
Tensile Strength
Tough dry at 30oC: Maximum of one (1) hour and thirty ASTM D412
(30) minutes Adhesion with
1.03 N/mm²
Can easily be repaired if membrane is damaged concrete
Environmental friendly product 0.17 kgf/ mm
Adhesion Peel
ASTM D903: 2017
100% A/B
Application areas Adhesion Strength
ASTM D4541: 2009 e1
Waterproofing of Rooftops (concealed) Water Vapor 1.36e-06
Waterproofing of Balconies / Terraces (concealed) Transmission ASTM E96: 2016
Waterproofing of Wet areas (under tiles) in Toilet & Solid by Volume 80%
Bath, Kitchens etc. Light-Heavy
Waterproofing, sealing and protection on different kind 12 hours cure time
Pedestrian Traffic
of roof such as tile roof, metal roofs, fiber-cement Conditions: 20°C, 50% R.H
Time
panels, etc. 47.5%
Flexible waterproofing under tiling for indoor or Nonvolatile Content
ASTM D6511:2011
outdoor applications VOC Less than 76.52 g/L
A highly UV resistant protective waterproofing material 2mm cracks
for facades, partitions, fire wall or exterior walls. Crack Bridging
ASTM C1305:2016
Sealing and waterproofing cracks, fissures, joints, Thickness 1mm DFT Required
junctions, passing pipes and other outstanding points
subject to movement Conforms to ASTM E96, ASTM C836, ASTM D903,
ASTM D4541 and ASTM C1305
…………..………………………...………………………………………………… Waterproofing Products
DECEMBER 2020 | Rev. 2
This technical data contained herein is true and accurate to the best of our knowledge on the date of publication and is subject to change without prior notice. User must contact Sealbond Chemical Industries Inc. to
verify correctness before specifying or ordering. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited replacement of products. Sealbond Hi-Perfomance is
registered trademark of Sealbond Chemical Industries Inc.
www.sealbondchemicals.com 1|P a g e
product data Waterproofing Products
OPTIMASTIC PU-W
Procedure & Guidelines Health & Safety
SURFACE PREPARATION Please wear rubber or plastic gloves to avoid contact with
GENERAL skin. Please refer to MSDS for other safety information.
All surfaces must be thoroughly cleaned to remove dirt, grease,
mill scale, loose rust, chalk, and any other contaminants that can Product is for Professional use only.
reduce adhesion.
Storage/ Packaging
CONCRETE / MASONRY
Cure for at least 28 days before application. Remove loose or OPTIMASTIC PU-W is available in 22 kg pail
excess mortar, efflorescence, laitance and concrete form release This product must be stored dry, protected from sun and
compounds that reduce adhesion. Etch or abrasive blast polished rain. No waterproofing works should be performed if weather
or glazed concrete before use on floors.
is unsuitable. These includes heavy rain and moisture
PREVIOUSLY PAINTED SURFACES Product Limitation
Scrape loose, scaly, peeling paint and sand the edges smooth. If Product should not be applied directly to the substrate that
the paint is glossy, sand to dull the surface. Remove any rust and shows any hydrostatic pressure problems that may later
scale from ferrous metal. If mildew is present, remove completely cause disbonding.
by sterilizing the surface with mildew remover and detergent.
Rinse well and allow to dry before painting. Additional Information - Disclaimer
MIXING The information and in particular, recommendations relating to the application and
end-use of Sealbond products, are given in good faith based on Sealbond’s best
Stir well before application. knowledge and specialty on construction chemical formulations. Products are
properly stored and handled in accordance with Sealbond’s endorsements. Hence,
APPLICATION subject to the care and method of application, deviations (from published values) in
performance may occur. In practice, to different materials used, as well as varying
Apply one coat of Sealbond DPS Deep Penetrating Sealer (Refer
working conditions and environments beyond our control Sealbond Chemical
to Technical Data Sheet of Sealbond DPS). Industries Inc. strictly recommend carrying out intensive trials to test the suitability
OPTIMASTIC PU-W is ready to use. Apply two crossed coats by of the product with regards to the required processes and applications. Therefore,
brush, roller, or airless spray with consumption of 1.5-2.0 kg/m2 at any liability for such recommendations or any oral/verbal advice is expressly
1mm thickness, allowing a coating interval of 2-12 hours between excluded unless we have acted wilfully or by gross negligence. Sealbond
Chemicals Industries Inc. is not liable for installation or faulty installation. It is
coats depending on weather conditions. On vertical surfaces, always the responsibility of the installer/applicator/purchaser to guarantee and
apply in three or four coats to achieve the same total consumption. certify the installation of materials.
For improving adhesion of tile mortar or concrete topping, spread All orders are accepted subject to our current terms of sale and delivery. Users
dry sand on the second fresh coat. Clean application tools and must always refer to the most recent issue of the Product Data Sheet for the
equipment with water while the material is still wet. product awareness, copies of which will be supplied on request and is free of
charge.
Theoretical Coverage
Waterproofing weight
1.5-2.0 kgs/m² at 1mm thickness
Note: Above coverage are depending on the substrates per layer
Product is manufactured based on International
Environmental Regulations
OPTIMASTIC PU-W is a green revolution product in
waterproofing solutions.
A-2 Araneta St. Cor. Gen. Natividad St.
Bgy. Ibayo, Tipas Taguig City, Philippines
PH: (632) 881-8813 ● (632) 883-1477 ● (632) 845-0205
● (632) 843-4498 ● (632) 845-0137
www.sealbondchemicals.com
…………..………………………...………………………………………………… Waterproofing Products
DECEMBER 2020 | Rev. 2
This technical data contained herein is true and accurate to the best of our knowledge on the date of publication and is subject to change without prior notice. User must contact Sealbond Chemical Industries Inc. to
verify correctness before specifying or ordering. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited replacement of products. Sealbond Hi-Perfomance is
registered trademark of Sealbond Chemical Industries Inc.
www.sealbondchemicals.com 2|P a g e
