Technical Data

400 Series 403D-11G

ElectropaK
Basic technical data Note: All data based on operation to ISO 3046-1:2002 standard
Number of cylinders . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 3 reference conditions
Cylinder arrangement... ... ... ... ... ... ... ... ... ... ... ... Vertical in-line Speed variation at constant load - G2 ... ... ... ... ... ... ... ... ± 0,75%
Cycle ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . four stroke Cyclic irregularity
Induction system .. ... ... ... ... ... ... ... ... ... ... ... Naturally aspirated -at 110% stand-by power .. ... ... ... ... ... ... ... ... ... ... ... ... ... . .TBA
Compression ratio ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 23:1
Bore.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 77 mm Test conditions
Stroke... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 81 mm -air temperature. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 25 °C
Cubic capacity.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .1·131 litres -barometric pressure . ... ... ... ... ... ... ... ... ... ... ... ... ... ... 100 kPa
Direction of rotation .. ... anti-clockwise when viewed from flywheel -relative humidity ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...31.5%
Firing order... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1, 2, 3 -air inlet restriction at maximum power (nominal).. ... ... ... ... 3 kPa
Estimated total weight of Electropak (dry) ... ... ... ... ... ... 129,2 kg -exhaust back pressure at maximum power (nominal).. ...10,2 kPa
-fuel temperature (inlet pump) ... ... ... ... ... ... ... ... ... ... ... ... 40 °C
Overall dimensions of Electropak
-height .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 700 mm Sound level
-length .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 776 mm Average sound pressure level for bare engine
-width ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 449 mm (without inlet and exhaust) at 1 metre ... ... ... ... ... ... ... 78,5 dB(A)
-all ratings certified to within . ... ... ... ... ... ... ... ... ... ... ... ... ± 5%
Moments of inertia (GD²) If the engine is to operate in ambient conditions other than those of
-engine rotational components. ... ... ... ... ... ... ... ... ... . TBA kg m² the test conditions, suitable adjustments must be made for these
-flywheel .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1,51 kg m² changes. For full details, contact Perkins Technical Service
Department.
Centre of gravity (fan face to flywheel housing) Emissions Statement: Certified against the requirements of
-forward from rear of block ... ... ... ... ... ... ... ... ... ... ... ... ... 98 mm
EU2007 (EU 97/68/EC Stage II) and EPA Tier 4 (EPA 40 CFR Part
-above crank centre line... ... ... ... ... ... ... ... ... ... ... ... ... ... 67 mm
1039 Tier 4 legislation for non-road mobile machinery, powered by
-offset to RHS of centre line . ... ... ... ... ... ... ... ... ... ... ... ... 2 mm
constant speed engines
Performance

General installation
Type of operation and application
Designation Units
Prime Stand-by
Gross engine power kWb 10,7 11,8
ElectropaK net engine power kWm 10,3 11,4
Brake mean effective pressure kPa TBA TBA
Engine coolant flow (Water Pump Ratio 1.285:1) l/min 32,5
Combustion air flow m³/min 0,9
Exhaust gas flow (max.) m³/min 2·21 2,4
Exhaust gas temperature (max. ) °C 437 515
Overall thermal effeciency (nett) % 32 31
kWe 9,0 9,9
Typical genset electrical output (0.8 pf 25 °C)
kVA 11,2 12,4
Assumed alternator efficiency % 87
Energy balance
Energy in fuel kWt 31,8 37,8
Energy in power output (gross) kWb 10,7 11,8
Energy to cooling fan kWm 0,4 0,4
Energy in power output (nett) kWt 10,3 11,4
Energy to coolant and lubricating oil kWt 10,2 12,1
Energy to exhaust kWt 8,9 10,8
Energy to radiation kWt 2,6 3,1
403D-11G ElectropaK, left side view
481
219

328 228

683

776
403D-11G ElectropaK, front view

248 201

188 176

141 141

322
403D-11G ElectropaK, plan view
Cooling system Exhaust system
Radiator Maximum back pressure... ... ... ... ... ... ... ... ... ... ... ... ... 10,2 kPa
-face area ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .0,147 m² Exhaust outlet size
-rows and materials . ... ... ... ... ... ... ... ... ... ... . 2 rows, Aluminium -horizontal . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 34 mm
-matrix density and material ... ... ... ... ... ... .. 14,5 FPI, Aluminium -vertical . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 40 mm
-width of matrix ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..334 mm
-height of matrix... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..440 mm
-pressure cap setting ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 90 kPa Fuel system
Estimated cooling air flow reserve... ... ... ... ... ... ... ... ...0,125 kPa
Type of injection ... ... ... ... ... ... ... ... ... ... ... ... ... Indirect injection
Fan Fuel injection pump... ... ... ... ... ... ... ... ... ... ... ... ... Cassette type
-diameter . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 320 mm Fuel injector .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . Pintle nozzle
-drive ratio ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...1,285:1 Nozzle opening pressure .. ... ... ... ... ... ... ... ... ... ... ... .. 14·7 MPa
-number of blades ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .7
-material... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Plastic Fuel lift pump
-type. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Pusher -flow/hour .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .63 litres/hr
-pressure... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 10 kPa
Coolant Maximum suction head . ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0,8 m
Total system capacity Maximum static pressure head . ... ... ... ... ... ... ... ... ... ... ... 3,0 m
-with radiator ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 5,2 litres Governor type ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Mechanical
-without radiator... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 1,9 litres
Maximum top tank temperature... ... ... ... ... ... ... ... ... ... ... 112 °C Fuel specification
Temperature rise across engine.. ... ... ... ... ... ... ... ... ... ...TBA °C USA Fed Off Highway - EPA2D 89.330-96
Max permissible external system resistance ... ... ... ... ... .TBA kPa Europe Off Highway - CEC RF-06-99
Thermostat operation range ... ... ... ... ... ... ... ... ... ... ... 75 - 87°C Note: For further information on fuel specifications and restrictions,
Recommended coolant: 50% anti freeze / 50% water. For complete refer to the OMM Fuels section for this engine model
details of recommended coolant specifications, refer to the
Fuel consumption
Operation and Maintenance Manual for this engine model
Power rating
Duct allowance g/kWh
110% 100% 75% 50%
Maximum additional retsriction (duct allowance) to cooling
airflow and resultant minimum airflow 268 248 257 280
Ambient clearance Duct allowance
m³/sec
50% Glycol Pa
53°C 0 0,75
46°C 125 0,59

Electrical System
-alternator ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 15 amps, 12 V
-starter motor ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 1,1 kW, 12 V

Cold start recommendations

Minimum cranking speed. ... ... ... ... ... ... ... ... ... ... ... TBA rev/min
Minimum Battery specifications
starting Grade of
engine BS3911 SAEJ537
temperature Number of
lubricating Cold Cold Commercial
batteries
oil start cranking ref number
°C needed
amps amps

0 20W 340 540 1 069

-15 10W 340 540 1 069
-20 5W 420 590 1 072
400 Series 403D-11G

Induction system Load acceptance

The below complies with the requirements of classification 3 and 4
Maximum air intake restriction of ISO 8528-12 and G2 operating limits stated in ISO 8528-5
-clean filter ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 3,0 kPa Initial load application: When engine reaches rated speed
-dirty filter . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 6,4 kPa (15 seconds maximum after engine starts to crank)
-air filter type ... ... ... ... ... ... ... ... ... ... ... ... ... ... Dry element type
Descriptor Units 60 Hz
% of prime power % tba
Lubrication system Load kWm (kWe) tba
Transient frequency
%
Lubricating oil capacity deviation
Total system. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .4,9 litres Frequency recovery Seconds tba
Minimum... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .3,4 litres
The above figures were obtained under the following test
Maximum engine operating angles
conditions:
-front up, front down, right side or left side... ... ... .. 35° continuous
-minimum engine block temperature . ... ... ... ... ... ... ... ... .. tba °C
Lubricating oil pressure -ambient temperature ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...tba °C
-relief valve opens ... ... ... ... ... ... ... ... ... ... ... ... ... 304 - 500 kPa -governing mode ... ... ... ... ... ... ... ... ... ... ... ... ... ... isochronous
-at maximum no-load speed. ... ... ... ... ... ... ... ... ... ... ... ... ... TBA -alternator inertia ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. tba kgm²
Normal oil temperature. ... ... ... ... ... ... ... ... ... ... ... ... ... ... 125 °C -under frequency roll off (UFRO) point set to ... .. 1 Hz below rated
-oil consumption at full load (as a % of fuel consumption) ... ... ... .. -UFRO rate set to .. ... ... ... ... ... ... ... .. 2% voltage / 1% frequency
LAM on/off . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . off
Recommended SAE viscosity All tests were conducted using an engine which was installed and
A single or multigrade oil must be used which conforms API-CH-4 serviced to Perkins Engines Company Limited recommendations.
or ACEA E5. Note: The general arrangement drawings shown in this data sheet
are for guidance only. For installation purposes, latest versions
should be requested from the Applications Dept., Perkins Engines
Stafford, ST16 3UB United Kingdom.
0W
5W20
10W30
15W40
20W50
20
30
40
-30 -20 -10 0 10 20 30 40 50oC
-22 -4 14 32 50 68 86 104 122oF
Ambient temperarture
W1355

Maximum static bending moment

at rear face of block.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..500 Nm

Publication No. TPD1647E1. February 2008 © Perkins Engines Company Limited

@Perkins ®
Distributed by

Perkins Engines Company Limited

Peterborough PE1 5NA United Kingdom
Telephone +44 (0) 1733 583000
Fax +44 (0) 1733 582240
www.perkins.com

All information in the document is substantially correct at the time

of printing but may be subsequently altered by the company.