Network Video Recorder: Product Specifi Cation Manual
Network Video Recorder: Product Specifi Cation Manual
XRN-2010/2011/2010A/2011A
XRN-3010/3010A
XRN-1610/1610S/1610A/1610SA
Network Video Recorder
Product Specification Manual
Copyright
©2018 +DQZKD7HFKZLQ Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of
their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly,
without formal authorization.
Disclaimer
+DQZKD7HFKZLQ makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. +DQZKD7HFKZLQ reserves the right
to change the contents of this document without prior notice.
The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the
information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
overview
IMPORTANT SAFETY INSTRUCTIONS BEFORE START
Read these operating instructions carefully before using the unit. This manual provides operational information necessary for using the product and contains a description about each
Follow all the safety instructions listed below. component part and its function as well as menu or network settings.
Keep these operating instructions handy for future reference. You have to keep in mind the following notices :
1) Read these instructions. • Hanwha Techwin retains the copyright on this manual.
2) Keep these instructions. • This manual cannot be copied without Hanwha Techwin's prior written approval.
3) Heed all warnings. • We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
4) Follow all instructions.
• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
5) Do not use this apparatus near water.
removed from the unit.
6) Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
• Before adding a hard disk drive or external storage (USB memory, USB HDD, etc), check if it is compliant with this
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil
product. For the compatibility list, contact the retailer.
constituents as they may deform or cause damage to the product.)
7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
Warning
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Battery
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The It is essential that when changing the battery in the unit, the replacement battery must be of the same type
wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, otherwise there may be a possibility of an explosion.
consult an electrician for replacement of the obsolete outlet. The following are the specifications of the battery you are using now.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, • Normal voltage : 3V
and the point where they exit from the apparatus. CALIFORNIA USA ONLY
• Normal capacity : 210mAh This Perchlorate warning applies only to primary CR (Manganese Dioxide)
11) Only use attachments/accessories specified by the manufacturer. Lithium coin cells in the product sold or distributed ONLY in California USA.
• Continuous standard load : 0.4mA "Perchlorate Material - special handling may apply,
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, See www.dtsc.ca.gov/hazardouswaste/perchlorate."
or sold with the apparatus. When a cart is used, use caution when moving the cart/ • Operating temperature : -20°C ~ +60°C
apparatus combination to avoid injury from tip-over. (-4°F ~ +140°F)
13) Unplug this apparatus during lightning storms or when unused for long periods of
time. Caution
14) Refer all servicing to qualified service personnel. Servicing is required when the • Connect the power cord into a grounded outlet.
apparatus has been damaged in any way, such as power-supply cord or plug is
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped. • Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Standards Approvals
• When the HDD reaches its end of life, the stored video data may be damaged, and not be able to be
recovered.
• The HDD status LED on the front of the system continuously blinks to indicate that the system's connection
to the HDD is normal. Check the HDD status LED regularly to see if it blinks continuously. Recording may not
` Any changes or modifications in construction of this device which are not expressly approved by the party responsible for
J compliance could void the user's authority to operate the equipment.
be possible when there is an HDD failure.
Periodically check the recording status and backup important data regularly.
` This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
M not cause harmful interference, and (2) this device must accept any interference received, including interference that may
ATTENTION
cause undesired operation. • IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE
INCORRECT.
` This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
English _3
overview
System Shutdown NVR products supporting each feature
Turning off the power while the product is in operation, or undertaking improper actions may cause damage or
malfunction to the hard drive or the product.
To safely power off, select Exit from the menu and click <OK> on the pop-up screen, then unplug the power Function Products
cable. XRN-3010, XRN-3010A, XRN-2010, XRN-2010A, XRN-2011, XRN-2011A, XRN-1610,
You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected Fan
XRN-1610A, XRN-1610S, XRN-1610SA
power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
RAID XRN-2011, XRN-2011A
` If powered off abnormally, restarting may take more time for restoring data from hard disk drive for proper operation.
J iSCSI
XRN-2010, XRN-2010A, XRN-2011, XRN-2011A, XRN-1610, XRN-1610A, XRN-1610S,
XRN-1610SA
Operating Temperature
PoE XRN-1610S,XRN-1610SA
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the P2P XRN-3010A, XRN-2010A, XRN-2011A, XRN-1610A, XRN-1610SA
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at Remote controller XRN-1610, XRN-1610A, XRN-1610S, XRN-1610SA
room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). XRN-3010, XRN-3010A, XRN-2010, XRN-2010A, XRN-2011, XRN-2011A, XRN-1610,
Joystick
Likewise, the hard drive may not work at a temperature below the guaranteed one. XRN-1610A, XRN-1610S, XRN-1610SA
4_ overview
overview
CONTENTS
3 5
6
7
Contents
Features
Part Names and Functions (Front)
16
8 Part Names and Functions (Rear)
PRODUCT OVERVIEW 22 Product Overview
INSTALLATION 9
9
Checking the installation environment
Rack Installation
22
9 10 HDD Addition
13 13
14
Connecting the Alarm Input/Output
Connecting the Network
English _5
overview
FEATURES Package Contents
The product records video and audio from network cameras to a hard disk, and enables playback from the hard disk. Please unwrap the product, and place the product on a flat place or in the place to be installed.
It also provides remote monitoring environment for video and audio over the network using a remote computer. Please check the following contents are included in addition to the main unit.
• User-friendly UI The appearance of the components may differ from the image shown.
• Supports a range of 4K camera resolutions (3840X2160, 4096X2160, 4000X3000)
M Accessory category and quantity may differ depending on sales region.
• Outputs a 4K high definition image using HDMI For some regions, HDD is not pre-installed. HDD Fixing Screw, SATA Power Cable, SATA data cable and SATA power/data
• Record and play video cable quantity vary depending on the model.
USB
6_ overview
overview
XRN-1610/1610S/1610A/1610SA PART NAMES AND FUNCTIONS (FRONT)
XRN-2010/2010A/3010/3010A/1610/1610S/1610A/1610SA
NETWORK VIDEO RECORDER
USB
NVR Mouse
USB
b
Power Cable Terminal block
Remote Control / XRN-2011/2011A
Remote Control Battery (AAA)
LED Indicator
NETWORK : Displays both network connection and data transfer status.
RAID : Stays ON when RAID is in use. It flickers if backup is activated when RAID is in use.
Flickers only when backup is in operation if RAID is not in use. (XRN-2011/2011A)
English _7
overview
PART NAMES AND FUNCTIONS (REAR) Part Names Functions
NO NC NO NO NO G
COM COM COM COM
1 2 3 4 ALARM OUT
eSATA NETWORK 1 AUDIO OUT RS-232C HDMI USB CONSOLE eSATA Terminal to connect an external storage device.
NETWORK1 Port recommended for camera connection, which receives an image from the camera.
c NETWORK2 Port recommended for connection with a network, web viewer or iSCSI.
1 3 5 7 9 11 13 15
NETWORK 2 ALARM IN
1 2 3 4 5 6 7 8
ALARM
RESET
G
VGA OUT USB Connects the USB devices. (USB 3.0 supported)
POE AUDIO OUT
CAMERA HDMI USB CONSOLE
eSATA
NETWORK 1 NO NC NO NO NO G
Power Terminal to connect power to.
2 4 6 8 10 12 14 16 COM COM COM COM
1 2 3 4 ALARM OUT
Power Switch Power on/off switch. (XRN-1610S/1610SA)
c
8_ overview
installation
Please take note of the followings before using this product. RACK INSTALLATION
• Do not use the product outdoor.
• Do not spill water or liquid in the connection part of the product. Install the Bracket-Rack as shown in the figure, and then fasten the
• Do not impose the system to excessive shock or force. screws on both sides.
• Do not pull out the power plug forcefully. ` Fix the screws not to be loosened by vibrations.
• Do not disassemble the product on your own.
• Do not exceed the rated input/output range.
• Use a certified power cord only.
• For the product with an input ground, use a grounded power plug.
When mounting the product on a rack, comply with the following instructions.
1. Please ensure that the rack inside is not sealed.
2. Please ensure the air is circulated through the inlet/outlet as shown in the picture. 2. “FOOT” is separated from the main body when it is turned
3. If you pile up the prudcts or other rack-mount devices as shown in figure 2, secure room for to the end of fastening groove.
ventilation or install a vent.
4. For natural air convection, place the inlet at the bottom of the rack and the outlet on top.
5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for air
circulation. (Please fit a filter at the inlet to screen dust or foreign substances.) <Separation> <Installation>
6. Please maintain the temperature inside the rack or surrounding areas between 0°C ~ 40°C
(32°F ~ 104°F) as shown in the figure 1.
Rack Mount Instructions - The following or similar rack-mount instructions are included with
the installation instructions :
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified by the [Figure 2]
manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required
for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
English _9
installation
HDD ADDITION Installing the HDD
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product damage. ` If you are adding a new or previously used HDD to this product in addition to the HDD(s) originally installed, format the new
Please consult your provider for further information on HDD installation since improper installation or settings may J HDD manually in the set before use.
damage the product. To learn how to format, see "Device/Format" in the Wisenet NVR User Manual.
` Number of HDDs supported : Up to 8 HDDs supported
` Make sure to unplug the power cord from the wall outlet before proceeding with the installation.
How to install an HDD in XRN-2010/2010A/3010/3010A/1610/1610A/1610S/1610SA
` Cautions for data loss (HDD care)
J Please pay attention so that the data inside the HDD is not damaged.
1. Remove the screws located on the left/right side and on the
back side first, then remove the cover.
Before adding a HDD, please check the compatibility with this product.
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.
Please ensure that the HDD is free from such shock. USB
We are not liable for any damage to the HDD incurred by user's carelessness or miss use.
` Cases might cause damage to HDD or recorded data
To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.
If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged.
A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive.
HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.
2. Remove the screws on the left/right side (4 screws) and remove
the bracket.
Bracket
Cautions when installing a HDD
NO NC
COM
1
4 5 6
NO
2
NO
7 8
COM COMNO
3
ALARM
IN RESET
COM G
4 ALARM
OUT
eSATA
NETWORK
NETWORK
2
RS-232C
1
AUDIO
OUT
` Please contact your nearest dealer to obtain the list of compatible devices.
VGA OUT
HDMI
USB
CONSOLE
ALARM ALARM
1 2 3 IN RESET
4 5 6
7 8
G
NETWORK
2
NO NC
NONO
COM RS-232C
COM COMNO
1 COM G
2 3 eSATA
4 ALARM NETWORK
OUT 1
AUDIO
OUT
VGA OUT
HDMI
USB
CONSOLE
10_ installation
installation
4. Connect the cable to the HDD by matching the HDD SATA/ 6. Check for any problems in the connection terminal and the
power cable number to the HDD position number on the wiring in the product, close the cover and fix it with screws.
bracket. Bracket
` For the HDD location number on the bracket, please refer to the figure
below. USB
ALARM ALARM
1 2 3 IN RESET
4 5 6
7 8
G
NO NC
NO NO
COM RS-232C
COM COMNO
1 COM G
2 3 eSATA
4 ALARM NETWORK
OUT 1
AUDIO
OUT
VGA OUT
HDMI
USB
CONSOLE
1. Open the front cover and check the HDD installation bracket.
` Release the USB connection before opening the front cover to prevent
5. Mount the bracket on which an additional HDD is mounted on
the NVR, secure it with screws and connect the SATA/power
J damage to the USB port.
cable to the connector on the main board by matching the
number.
` For the connector numbers, please refer to the figure below. ALARM
1 2 3
4 5 6
7 8
ALARM
IN RESET
NETWORK
2
NO NC
NO NO
COM VGA OUT
COM COMNO
1 COM G
2 3 eSATA
4 ALARM NETWORK
OUT 1
AUDIO
OUT
RS-232C
HDMI
USB
CONSOLE
8
5
6
3
2. Push the latch to the right and remove the HDD bracket.
1
4
8 2
` Take care not to scratch your hands when removing the HDD bracket.
J
6 7
5 3
4
2 1
<XRN-2010/2010A/3010/3010A/1610/1610A>
3. Align and insert HDD into the bracket home. After inserting one
side, push and insert the other side slightly.
1
3
PoE 5
CAMERA 7
9
11
13 NETWORK
15 2
2 ALARM ALARM
4 1 2 3 IN RESET
6 4 5 6
7 8
8 G
VGA OUT
10
12
14 eSATA AUDIO
OUT
16
NETWORK
1
eSATA
NO NC HDMI
NO NO
COM
COM COMNO USB
1 COM G CONSOLE
2 3 4 ALARM
OUT
4
3
2
12
<XRN-1610S/1610SA>
English _11
installation
4. Align the bracket with the HDD installed with the enclosure
latch, and push the bracket in the direction of the board.
` Push it until you hear the latch lock sound. If the HDD is not completely
J connected, it may be detected.
` The procedure after HDD exchange is the same as the procedure for
M "Installing the HDD".
12_ installation
connecting with other device
CONNECTING TO AN EXTERNAL DEVICE CONNECTING THE ALARM INPUT/OUTPUT
The Alarm In/Out port at the back is composed of the following.
ALARM
ALARM IN RESET
NETWORK 2
1 2 3 4 5 6 7 8 G
VGA OUT
ALARM
ALARM IN RESET
NETWORK 2
NO NC NO NO NO G eSATA NETWORK 1 AUDIO OUT RS-232C HDMI USB CONSOLE 1 2 3 4 5 6 7 8 G
COM COM COM COM
1 2 3 4 ALARM OUT
VGA OUT
ALARM
VGA
A OUT
O ALARM IN RESET
1 2 3 4 5 6 7 8 G
NO NC NO NO NO G
COM COM COM COM
Sensors 1 2 3 4 ALA
ALARM
ARM OUT
Alarm
VIDEO OUT
• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and
AUDIO OUT HDMI OUT
(VGA) resumes sensing.
• ALARM OUT 1 ~ 4 : Alarm Output Port
` Unrated or improper power source may cause damage to the system. Ensure that you use only the rated power source
J before pressing the POWER button.
` If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the NVR.
J
` Some USB devices may fail to function properly due to compatibility issue, please check the device before using.
` Only USB storage devices that comply with the standards (having a metal cover) are guaranteed for data transfer.
` In case if the USB device’s electric contacts have been worn out, data transfer between the devices may not properly
function.
English _13
connecting with other device
CONNECTING THE NETWORK Connecting to Internet through PPPoE
` For more information about network connection, see "Network Configuration" in the Wisenet NVR User Manual.
M ALARM IN
1 2 3 4 5 6 7 8
ALARM
RESET
G
NETWORK 2
VGA OUT
NETWORK 2
ALARM IN
1 2 3 4 5 6 7 8
ALARM
RESET
G
NETWORK 2 NETWORK
VGA OUT
NO NC NO NO NO G
COM COM COM COM
eSATA
TA NETWORK 1 AUDIO
A OUT RS-232C HDMI USB CONSOLE
Phone(PPPoE) PPPoE MODEM Switch
1 2 3 4 ALARM OUT
Line NETWORK 1
Switch
NETWORK 2
Switch
Switch
NETWORK 1 Windows
Network Viewer
ex) IP : 192.168.231.100
1 3 5 7 9 11 13 15 ALARM
ALARM IN RESET VGA OUT
NETWORK 2
1 2 3 4 5 6 7 8 G
NO NC NO NO NO G eSATA
A NETWORK 1 AUDIO
AU OUT RS-232C HDMI USB CONSOLE
COM COM COM COM
1 2 3 4 ALARM OUT
1 3 5 7 9 11 13 15 NETWORK 2
NETWORK 2
Switch POE
2 4 6 8 10 12 14 16
NETWORK 1 equipments through
Brodband router network1 in PnP mode.
NETWORK 1
xDSL or Cable
Modem xDSL or Cable
Modem
Windows
DDNS Server
Network Viewer
(Data Center)
ex) IP : 192.168.1.100
1 3 5 7 9 11 13 15 ALARM
ALARM IN RESET VGA OUT
NETWORK 2
1 2 3 4 5 6 7 8 G
ALARM
ALARM IN RESET
NETWORK 2
POE AUDIO OUT 1 2 3 4 5 6 7 8 G
CAMERA HDMI USB CONSOLE
eSATA
VGA OUT
NETWORK 1 NO NC NO NO NO G
2 4 6 8 10 12 14 16 COM COM COM COM
1 2 3 4 ALARM OUT
NO NC NO NO NO G eSATA
A NETWORK 1 AUDIO
AU OUT RS-232C HDMI USB CONSOLE
COM COM COM COM
1 2 3 4 ALARM OUT
1 3 5 7 9 11 13 15
Switch
NETWORK 2 NETWORK 2
Switch
POE
CAMERA
AMERA
NETWORK
ORK 1
NETWO
2 4 6 8 10 12 14 16
16
NETWORK 1
Switch
iSCSI
Network Camera
Network Camera Network Camera Network Camera Network Camera Network Camera
ex) IP : 192.168.1.20 ex) IP : 192.168.1.10
ALARM
ALARM IN RESET
NETWORK 2
1 2 3 4 5 6 7 8 G
VGA OUT
NO NC NO NO NO G eSATA
A NETWORK 1 AUDIO
AU OUT RS-232C HDMI USB CONSOLE
COM COM COM COM
1 2 3 4 ALARM OUT
NETWORK 2
iSCSI
NETWORK 1
English _15
product specification
• XRN-2010/2011/2010A/2011A
Details
Item
Details XRN-2010/2010A XRN-2011/2011A
Item
XRN-2010/2010A XRN-2011/2011A Sensor I/O 8/4 (NO/NC Selectable)
Performance TCP/IP, UDP/IP, RTP (UDP), RTP (TCP), RTSP, NTP, HTTP, DHCP (Server,
Protocol Client), PPPoE, SMTP, ICMP, IGMP, ARP, DNS, DDNS, uPnP, HTTPS,
Operating System Embedded Linux SNMP, ONVIF (Profile-S), SUNAPI(Server, Client)
8 (RAID5 : Hot Swap) Web Browser MS IE, Google Chrome, Mac Safari
Internal HDD
- Max. 48TB(Non-RAID), Max. 36TB(RAID-5)
Storage Type SSM, Webviewer, SmartViewer, Wisenet Mobile Viewer
External iSCSI storage(Max. 384TB) Viewer Software
CMS Support SDK/CGI
RAID-5(Array Size : 4-HDD x 2
RAID - Support Model Android, iOS
Array)
File backup (Via Web) BU/Exe(GUI), JPG/AVI(Network) Protocol Support RTP, RTSP, HTTP, CGI
Backup Smart phone
Function Max. 16CH Playback, Date-Time/Title display Control Live(16ch) / Playback(1ch)
Functions System
Control Via GUI, Webviewer, SPC-2000 Log Log List Max. 20000 (System Log, Event Log each)
PTZ
Preset 300 Presets Environmental
Failover 32 (Normal) + 1 (Standby) Operating Temperature / Humidity +0°C to +40°C (+32°F to +104°F)
Redundancy
ARB Yes Humidity 20% ~ 85% RH
LED Status indicator : LED Status indicator : Power Consumption 99W (6TB HDD x 8ea)
Indicator HDD Action(1), Alarm(1), Power(1), HDD Action(1), Alarm(1), Power(1),
Front Record(1), Backup(1), Network(1) Record(1), RAID(1), Network(1) Mechanical
VGA 1 EA (Up to 16 split screen mode Live Support) Dimension (WxHxD) 440x88x384.8 (17.32" x 3.46" x 15.15") (2U)
Serial RS-232C
Reset -
English _17
product specification
• XRN-3010/3010A
Item Details
Fisheye Dewarping Web / CMS Web Browser MS IE, Google Chrome, Mac Safari
Playback Control Fast/Slow Forward/Backward, Move one step up/down Type SSM, Webviewer, SmartViewer, Wisenet Mobile Viewer
Viewer Software
Built-In 0TB ~ 8TB CMS Support SDK/CGI (SUNAPI)
Protocol Support RTP, RTSP, HTTP, CGI(SUNAPI) Log Log List Max. 20000 (System Log, Event Log each)
Smart phone Live(16ch) : Multi-Profile Support Environmental
Control
Playback(1ch)
Operating Temperature / Humidity +0°C to +40°C (+32°F to +104°F)
Max. Remote Users Search(3) / Live unicast(10) / Multicast(20)
Humidity 20% ~ 85% RH
Failover N+1 (Include Fail-Back)
Redundancy Electrical
ARB Yes
Power 100 to 240 VAC ±10%; 50/60 Hz, 4~1.5A
System Control Mouse, Web, SPC-2000(Controller)
Power Consumption Max. 99W (338BTU, 6TB HDD x 8ea)
Indicator/Interface
Mechanical
LED Status indicator (6EA) : HDD Action(1), Alarm(1), Power(1),
Front Indicator Color / Material Black / Metal
Record(1), Backup(1), Network(1)
VGA Sub : 1 EA (Support Live screen upto 16 div. mode) Dimension (WxHxD) W440xH88xD384.8 (17.32" x 3.46" x 15.15") (2U)
Main : 1 EA (Both Support Live / PB / Setup) Weight 4.86Kg (10.71 lb, HDD not included)
HDMI
- Support upto 4K (3840 x 2160, Single Monitor Mode)
Recording performance spec for the HDD condition
Audio Out(1EA, RCA, Line)
Recording
Ethernet RJ-45 2EA (LAN/WAN, 1Gbps) Mode HDD condition
Internal
1) In(8EA, Terminal Block) General mode - 150
2) Alarm Reset(1EA) 1 HDD 150
Distributed mode
Alarm 3) Out (4EA, Terminal Block) 2 or more HDDs 300
Connectors
- Relay Out1(NO/NC/COM)
- Relay Out2~4(NO/COM)
Storage 1 e-SATA
Serial RS-232C
Reset Switch(1EA)
English _19
product specification
• XRN-1610/1610S/1610A/1610SA
Details
Item
Details XRN-1610/1610A XRN-1610S/1610SA
Item
XRN-1610/1610A XRN-1610S/1610SA Sensor I/O 8/4 (NO/NC selectable)
Network Camera Resolution CIF ~ 12MP Audio Communication 2-Way (pass-through between camera and SSM)
Local Display 1x HDMI / 1x VGA Dual Monitor TCP/IP, UDP/IP, RTP (UDP), RTP (TCP), RTSP, NTP, HTTP, DHCP (Server,
Protocol Client), PPPoE, SMTP, ICMP, IGMP, ARP, DNS, DDNS, uPnP, HTTPS,
[Local Monitor] SNMP, ONVIF (Profile-S), SUNAPI(Server, Client)
12MP (30fps)
Live DDNS Hanwha DDNS
8MP(120fps)
Performance
5MP(180fps), 3MP(240fps), 2MP(480fps), 720p(480fps), D1(480fps) Max. 256Mbps (iSCSI off)
Transmission Bandwidth
[Web] Max. 128Mbps (iSCS on)
5MP(30fps), 3MP(60fps), 2MP(120fps), 720p(240fps), D1(480fps) Max Remote Users Search(3) / Live unicast(10) / Live multicast(20)
Performance IP Version IPv4/v6
Operating System Embedded Linux User access Log, IP Filtering, 802.1x, Encryption (ID/PW, Recording,
Security
Transmission, Backup)
Compression H.265, H.264, MJPEG, WISESTREAM(H.265, H.264)
English, French, German, Italian, Spanish, Russian, Turkish, Polish,
Record Recording Bandwidth 180Mbps
Dutch, Swedish, Czech, Portuguese, Danish, Rumanian, Serbian,
GUI
Resolution CIF ~ 12MP Croatian, Hungarian, Greek, Norwegian, Finnish, Korean, Chinese,
Language Japanese, Thai
Playback Bandwidth 32Mbps (16ch simultaneously)
English, French, German, Italian, Spanish, Russian, Turkish, Polish, Dutch,
Performance Max. 4 Users (Local 1, Remote 3) Web Swedish, Czech, Portuguese, Danish, Rumanian, Serbian, Croatian,
Hungarian, Greek, Norwegian, Finnish, Korean, Chinese, Japanese
Simultaneous playback Up to 16CH (Local, Network)
Search & Play Windows XP(service pack 2 or above), Vista, 7, 8, 10, Mac OS X(10.7 or
Resolution CIF ~ 12MP OS
above)
Fish-Eye Dewarping processed on Web / CMS Plug-in free web viewer
Playback Control Fast/Slow Forward/Backward, Move one step up/down Supported Browser: Google Chrome 47, MS Edge 20
WMF : 1CH LIVE(800X600), SETUP
Default Built-In 0TB ~ 6TB Web Browser
Plug-in Webviewer
Storage Internal 8 SATA (Max. 48TB) 4 SATA (Max. 24TB) Supported MS Explore 11, Mozilla Firefox 43, Apple Safari 9 * Mac OS X
only
External 1 e-SATA, iSCSI (Max. 384TB)
Type SSM, Webviewer, SmartViewer, Wisenet Mobile
File backup BU/EXE(GUI), JPG/AVI(Network) Viewer Software
Backup CMS Support SDK/CGI (SUNAPI)
Function Max. 16CH Play, Date-Time/Title display
Protocol Support RTP, RTSP, HTTP, CGI (SUNAPI) 16EA (PoE(PoE+), 100Mbps)
2EA (LAN/WAN, 1Gbps)
Smart phone 2EA (LAN/WAN, 1Gbps)
Live(16ch) : Multi-Profile Support - LAN : Downlink to Camera/
Control Ethernet - LAN : Downlink to Camera/
Playback(1ch, Max 2MP) PoE(PoE+) Hub
PoE(PoE+) Hub
- WAN : Uplink to CMS
Max. Remote Users Search (3), Live Unicast (10), Multicast (20) - WAN : Uplink to CMS
NVR Time Protocol for PoE(PoE+) Reset Yes (Factory Reset, Alarm Reset)
Time Sync. - Camera (Time sync based on NVR
time) Power Cord Included
English _21
product overview
• XRN-2010/2011/2010A/2011A
unit : mm (inches)
<XRN-2010/2010A>
<XRN-2011/2011A>
English _23
product overview
• XRN-1610/1610A • XRN-1610S/1610SA
unit : mm (inches) unit : mm (inches)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
Head Office
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82.70.7147.8753 Fax : +82.31.8018.3740
www.hanwha-security.com