SGT5000_100-150_UPS_GE01

Technical Data Sheet

SGT5000_100-150_UPS_GE01
Technical Data
Digital Sheet SG Series
Energy™
(100-150kVA)
Digital Energy™
Technical SG SG
Data Sheet Series
Series (100-150kVA)
GENERAL DATA
(100-150kVA)
Topology True On-line double conversion
Nominal output power at PF = 0.7 lag. to 0.8 lag. kVA 100 120 150
GENERAL DATA
System efficiency 100% load, 0.8 PF : % 92.4 92.7 92.8
Topology 50% load, 0.8True PF :On-line double conversion % 92.9 93.1 93.3
Nominal output
Heat power
rejectionat PF = 0.7 load,
at 100% lag. to0.8PF
0.8 lag.
and charged battery kVA 100 BTU/hr 120 22,472 150 25,819 31,795
System efficiency 100% load, 0.8 PF : % 92.4 kW 92.7 6.58 92.8 7.56 9.31
Cooling Air (77°F - 86°F 50% / 25°C
load,- 0.8
30°C)PF : % 92.9CFM93.1 996 93.3 1,145 1,410
Audible
Heat rejection noiseload,
at 100% level0.8PF
(at 5 ft.)
and charged battery BTU/hr 22,472 dB(A) 25,81965 31,795 65 65
Operating temperature range UPS : 32°F - 104°F (0°C kW - 6.58
40°C) 7.56 9.31
Cooling Air (77°F - 86°F / 25°C - 30°C) Battery : 68°F - 77°F (20°C CFM - 25°C)
996 1,145 1,410
Audible noise level (at 5 ft.) (Note: Higher dB(A)
temperatures
65 shorten
65 battery
65 life)
Storage temperature
Operating temperature range range UPS : 32°F :- 104°F
UPS 5°F(0°C - 122°F (-15°C to +50°C)
- 40°C)
68°F :- 77°F32°F
Battery : Battery (20°C - 104°F
- 25°C) (0°C - 40°C)
(VRLA)
(Note: Higher Storage time is 6shorten
temperatures months at 77°F
battery life)(25°C)
Storage temperature range UPS : 5°F - 122°F(Note(-15°C to +50°C)
: Higher temperatures reduce battery storage time)
Relative humidity Battery : 32°F - 104°F 0-95%,
(0°C non-condensing
- 40°C)
Maximum altitude Storage
Without derating
(VRLA) : time3281ft (no derating)
is 6 months at 77°F (25°C)
With derating 4921ft/-5%
(Note :: Higher temperatures 6562ft/-9% 8202ft/-14%
reduce battery storage time)9843ft/-18%
Enclosure
Relative humidity 0-95%,
Type Indoor (IP20) and NEMA PE 1
: non-condensing
Maximum altitude Without derating : Safety 3281ft : (no Internal
derating) dead front construction
With derating : Cooling 4921ft/-5%
: Forced
6562ft/-9% Air (Redundant
8202ft/-14% Fans)
9843ft/-18%
Enclosure Type : Indoor
Color White
: (IP20) and(RAL NEMA 9010)
PE 1
Installation Internal
Safety : Rigging : deadSuitable
front for handling by forklift
construction
Forced
Cooling : Mounting : AirFloor mounting
(Redundant holes provided
Fans)
Installation and maintenance Black: (RAL
White
Color : access (RAL 9005)
Front
9010) access required for normal maintenance
Installation Conduit
Rigging Suitable
: Access : Top
for and Bottom
handling standard
by forklift
Standards Mounting : Floor mountingUL 1778, holes
IEC provided
62040, ISO9001, FCC Class A Optional
Electrostatic
Installationdischarge immunity access :
and maintenance Front access 4kVrequired
contact /for 8kV air discharge
normal maintenance
Configuration Conduit Access :Standard Top and: Stand-alone
Bottom standard
Standards Optional
UL 1778,: IEC RPA™62040, - up to 8 units
ISO9001, FCC may
ClassbeA paralleled
Optional in any
Electrostatic discharge immunity 4kV contact combination
/ 8kV air dischargefor redundancy or capacity
Configuration Standard : Stand-alone
RECTIFIER Optional : RPA™ - up to 8 units may be paralleled in any
Configuration combination Sixfor thyristor,
redundancy three or
phase bridge
capacity
Input Voltage : 480VAC, 3-phase, 3 wire + ground (NOTE 1)
RECTIFIER (-20% to +15% without battery discharge)
Configuration Six thyristor,
Frequency : 60Hz, three+/-10%
phase (54-66Hz)
bridge
Input Voltage Power
: 480VAC,
factor : 0.8 lagging
3-phase, (typical)
3 wire + ground (NOTE 1)
(-20%: to +15%
Inrush current Limited by soft-start
without circuit
battery discharge)
Frequency Power 60Hz,: +/-10%
: walk-in 30 seconds
(54-66Hz)(Adjustable)
Output
PowerVoltage 0.8 lagging
factor :Tolerance : +/- 1%
(typical)
DC ripple
Inrush current Limited
: voltage : by+/- 1%
soft-start circuit
DC ripple
Power walk-in 30 seconds
: current : Max. 5% of battery capacity expressed in amps
(Adjustable)
Data Output(kVA)
SG Series Voltage Tolerance : +/- 1% 100 120 150
Nominal inputDC (100%ripple
load) : +/- 1%
voltage Current[A] : 130.2 155.8 194.5
(0.8 PF load,DC ripple
fully current
chrg'd bat.) : Max.
kVA :5% of108.2 battery 129.5 capacity expressed in amps
161.6
Data SG Series (kVA) 100:
kW 12086.6 150 103.6 129.3
Maximum
Nominal input (100% input
load) (100% Current[A]
load) Current[A]
: 130.2 : 155.8150.4 194.5 185.3 220.2
(0.8fully
(0.8 PF load, PF chrg'd
load, max.
bat.) chrg current)
kVA : kVA
108.2: 125.0 161.6
129.5 154.0 183.0
kW : 86.6:
kW 103.696.0 129.3 119.0 147.0
Max. (100%
Maximum input current Current[A]0.8
chargeload) : PF load
150.4: 185.3 30 220.2 35 40
(0.8 PF load, max. chrg current) kVA : 125.0 154.0 183.0
NOTE 1: The Bypass input must be 480V/277V, 3-Phase, 4-Wire, WYE, plus ground, fed from a grounded-
kW : 96.0 119.0 147.0
WYE electrical system.
Max. charge current 0.8 PF load : 30 35 40
GEA-D2031 (Rev. 5, 11/7/06) Page 1 of 4 SG Series (100-150kVA)
NOTE 1: The Bypass input must be 480V/277V, 3-Phase, 4-Wire, WYE, plus ground, fed from a grounded-
WYE electrical system.

GEA-D2031 (Rev. 5, 11/7/06) Page 1 of 4 SG Series (100-150kVA)

 Battery
Battery compatibility Lead-acid or NiCd, VRLA or flooded
Number of cells 240 (lead-acid)
Float voltage at 68°F (20°C) 540VDC
Minimum discharge voltage 396VDC (adjustable)
Recharge time for 30 minute battery 10 times the discharge time
Battery ground fault detection Standard
Automatic and manual battery test Standard
Data SG Series (kVA) 100 120 150
100% load, 0.8 PF lag. kWB : 84.7 101.7 127.8
Maximum Discharge Current [A]: 218 261 325

Inverter
Nominal output voltage 480VAC, 3-phase, 4 wire + ground (NOTE 1)
Inverter bridge IGBT technology and Space Vector Modulation
Output Isolation transformer Standard
Output waveform True sine wave
Output voltage tolerance Static: +/- 1%
Load step 0% - 100% - 0% : +/- 3%, recovering to within +/- 1% in 1 cycle
Load step 0% - 50% - 0% : +/-2%, recovering to within +/- 1% in 1 cycle
100% unbalanced load (Ph-N) : +/- 3%
Output voltage distortion 100% linear load : 2% THD maximum
100% non-linear load (per IEC 62040) : 3% THD maximum
Crest factor capability Greater than 3:1
Output neutral rating 200%
Phase displacement 100% balanced load : 120°+/- 1%
100% unbalanced load : 120°+/- 2%
Output frequency Free running : 60Hz, +/- 0.01%
Synchronized with utility : +/- 4% (adjustable from 57.6Hz to 62.4Hz)
Overload capability (on inverter) 125% at 0.8 PF for 10 minutes
150% at 0.8 PF for 60 seconds
Short circuit capability (on inverter) 700% of rated current for first 1.2 ms, followed by
220% for 100 ms, electronically limited
Data SG Series (kVA) 100 120 150
Maximum Output Current @ 0.8pf [A]: 120.3 144.4 180.5

Bypass
Input configuration Common with rectifier (default) or dual input
Primary components Full load rated static switch
Back feed protection
Internal maintenance bypass
Transfer limits +/- 10% of nominal output voltage (adjustable)
Overload capability (on bypass) 110% continuous
200% for 5 minutes
Short circuit capability (on bypass) 1000% for 1/2 cycle (non-repetitive)

External Interface
Alarm contacts (voltage-free) Standard : 6 user defined contacts (form 'C')
Optional : 12 user defined contacts (form 'C')
(23 selectable signals include aux. Inputs 1 & 2)
Serial communication RS-232
Input signals Emergency Power Off (user supplied N.C. contact)
Aux. input 1 * (default = On Generator)
Aux. input 2 * (default = not defined)
* Status displayed on LCD panel

NOTE 1: The Bypass input must be 480V/277V, 3-Phase, 4-Wire, WYE, plus ground, fed from a grounded-
WYE electrical system.

2 SG Series (100-150kVA) | www.gecriticalpower.com

 Front Panel Controls, Signals & Alarms

(1) Mimic Diagram: Represents the operational status of the UPS, with integrated LEDs and
power flow indicators

(2) Service Check LED: Turns on when service is due or the internal manual bypass is active

(3) Common Alarm: Visual (LED) and audible signal active when any alarm condition is present

(4) Stop Operation: Visual (LED) and audible signal, activates approx. 3 minutes (adjustable)
before complete and automatic load shutdown (due to a fully discharged
battery or an over temperature condition with normal power not available)

(5) Load Level / Battery Run Time: Bar graph status indicator

(6) LCD Display: Display of UPS metering functions and event history (multi-language)

(7) Push Buttons: (7a) - Inverter On

(7b) - Inverter Off
(7c) - Alarm Silence
(7d) - Lamp Test
(7e) - Load Off with (protective cover)

Optional Features
RPA™ - Redundant Parallel Operation and Intellegent Energy Management (IEM)

Input/Output Transformers - Available in external cabinets for isolation or voltage transformation

5th Harmonic Input Filter - Integral to UPS cabinet. No additional cabinet required

External Maintenance Bypass - Available in 2 or 3 breaker, panel mounted configurations

Remote Status Panel - Active mimic diagram w/ Stop Operation and Summary Alarms

Protection Software - PC operated remote monitoring, control and diagnostics

SNMP Communication - Ethernet interface for network connection

FCC Filter - Brings UPS into compliance with FCC, Class A Specifications

3 SG Series (100-150kVA) | www.gecriticalpower.com

 Mechanical Data

100,120,150kVA Enclosure

UPS
Dimensions Weight
Rating
(kVA) Height (H) Width (W) Depth (D) UPS Floor Loading
100 71" 47" 32" 1,929 lbs 185 lbs/sq.ft
120 71" 47" 32" 2,006 lbs 192 lbs/sq.ft
150 71" 47" 32" 2,160 lbs 207 lbs/sq.ft

UPS Block Diagram

Alternate 1 Alternate 2
1……… Rectifier
2……… Inverter
3……..…Static Bypass
4……… Maintenance Bypass
5……… Utility
6……… Load Output
7……..…Battery
8……… Battery Contactor
FB……. Battery Fuses or Circuit Breaker
F in……AC Input Fuses or Circuit Breaker
Lb……. Battery Line
L in…… Input Line
L out……Output Line

GE
Critical Power
601 Shiloh Road *Registered trademark of the General Electric Company.
The GE brand, logo, and lumination are trademarks of the General Electric Company. © 2015 General Electric Company.
Plano, TX 75074 Information provided is subject to change without notice. All values are design or typical values when measured under
+1 877 546 3243 laboratory conditions.
www.gecriticalpower.com GEA-D2031, Rev. 07/2015

GEA-D2031 (Rev. 5, 11/7/06) Page 4 of 4 SG Series (100-150kVA)