Scribd
Upload
510 views2 pages

5 Pile Cap

The document summarizes the design of a pile cap to support a 600 kN axial load from a 400x600 mm column. Key details include: - The pile cap is 700 mm wide and 900 mm deep - Main reinforcement is 12 mm diameter bars at 110 mm c/c both ways - Shear reinforcement is 8 φ stirrups at 150 mm c/c - Punching shear and bending moment checks are satisfied - One-way shear check is also satisfied by the shear reinforcement

Uploaded by

PANKAJ TAMBAKHE
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
510 views2 pages

5 Pile Cap

The document summarizes the design of a pile cap to support a 600 kN axial load from a 400x600 mm column. Key details include: - The pile cap is 700 mm wide and 900 mm deep - Main reinforcement is 12 mm diameter bars at 110 mm c/c both ways - Shear reinforcement is 8 φ stirrups at 150 mm c/c - Punching shear and bending moment checks are satisfied - One-way shear check is also satisfied by the shear reinforcement

Uploaded by

PANKAJ TAMBAKHE
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

DESIGN OF PILE CAP-5

DATA:-

Pile Diameter : 400 mm


Column Dimension B x D : 400 x 600 mm
Axial Load : 600 KN
Concrete Mix : M20
Steel Grade : Fe 415
DESIGN : -
1. Pile Cap Dimension :

Width of Pile Cap = ( hp + 2 x 150 ) = 400 + 150 + 150 = 700 mm

Depth of Pile cap = 2 hp + 100 = 2 x 400 + 100 = 900 mm.

2. Net Upward Pressure :

Pu = 1.5 x 600 = 900 KN


2
Upward Pressure = 900 = 1836.73 KN / m

0.7x 0.7
3. Bending Moment :-
Projection = 0.70 – 0.40 = 0.15 m
2
2
B.M. in Pile cap at section A – A Mu = 1836.73 x 0.15 /2 = 20.66 KN.m

4. Check for effective depth :


2 6
Mu = 0.138 fck b d = 20.66 x 10
6
d required = √ (20.66 x 10 ) / 2.76 x 700 = 103.40 mm

D provided = 900 mm
d available = 900 – 60 -12- 6 = 822 mm > d required i.e. 103.4 mm
5. Check for Punching Shear : -
As single Pile is provided, the cap has to be checked for punching shear.
Area resisting punching = (600 x 2 + 400x 2) x 822
=( 2000 x 822 ) mm
3 2 2
Punching stress = 900 x 10 = 0.550N/mm < 1.12 N/mm

2000 x 822
6. Main Reinforcement : -

Mu = 20.66 KN.m
2 6
K = Mu / bd = 20. 66 x 10 = 0.04 < Table value
2
700 x 822
2
Minimum Ast = 0.12 x 700 x 822 = 690.48 mm

100
Provide 12 mm Dia RTS @ 110 mm c/c both ways at bottom.
Provide same at top along perpendicular direction of main reinforcement.
7. Check for one way shear :-
Shear force at section A – A at a distance d/2 = 822 /2 = 411 mm from face of
column = 1836.73 x 0.15 x 0.70 = 275.51 KN
3 2
Shear stress = 275.51 x 10 = 0.48 N/mm

822 x 700
2
Ast provided = 113 x 700/110 = 719.71 mm

Pt = 719.71 x 100 = 0.13 % < Minimum Pt of Table value of shear stress

700 x 822
2
For Pt = 0.20% ζc from Table 61 of Design Aid to IS 456 -1978 = 0.33 N /mm
-3
Balance shear Vus =275.51 – (0.33 x 700 x 822 x 10 ) =85.628 KN.

Vus /d = 85.628 / 82.2 =1.042 KN/cm

Provide 8 Φ RTS 2 legged stirrups @ 150 mm c/c.

You might also like