Scribd
Upload
149 views14 pages

Atm 1

This document describes a proposed system to prevent theft of ATM machines. The system uses a vibration sensor to detect if the ATM is being stolen. It then triggers a buzzer, closes the door using a DC motor, and releases gas using a relay to incapacitate the thief. An RTC captures the time and a GSM module sends an alert message to the bank and police. The system is implemented using an Arduino IDE and is intended to quickly detect and stop ATM theft.

Uploaded by

Chintapally Aditya Sameer Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
149 views14 pages

Atm 1

This document describes a proposed system to prevent theft of ATM machines. The system uses a vibration sensor to detect if the ATM is being stolen. It then triggers a buzzer, closes the door using a DC motor, and releases gas using a relay to incapacitate the thief. An RTC captures the time and a GSM module sends an alert message to the bank and police. The system is implemented using an Arduino IDE and is intended to quickly detect and stop ATM theft.

Uploaded by

Chintapally Aditya Sameer Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

NARSING BHAVANI

ECE – A
18951A0432
Anti-Theft Security And Automatic Door
Locking System For ATM Machine
contents
• Abstract
• Introduction
• Existing System
• Proposed System
• Design Considerations
• Advantages & Applications
• Result
• Future scope
• Conclusion
• References
ABSTRACT
• The Idea of Designing and Implementation of Security Based ATM theft project is
born with the observation in our real-life incidents happening around us. This
project deals with prevention of ATM theft from robbary.Whenever robbery occurs,
Vibration sensor is used here which senses vibration produced from ATM machine.
This system uses controller based embedded system to process real time data
collected using the vibration sensor. Once the vibration is sensed the beep sound
will occur from the buzzer. DC Motor is used for closing the door of ATM. Relay is
used to leak the gas inside the ATM to bring the thief into unconscious stage. RTC
used to capture the robber occur time and send the robbery occur time with the
message to the nearby police station and corresponding bank through the GSM.
Hear LCD display board using showing the output of the message continuously.
This will prevent the robbery and the person involving in robbery can be easily
caught. Here, Arduino IDE tools are used to implement the idea and results are
obtained. Arduino IDE tools is used for run the DC motor and Relay for automatic
door lock and also leak the gas inside the ATM.
INTRODUCTION
In today’s technically advanced world, autonomous systems are
gaining rapid popularity. As the social computerization and automation
has been increased and the ATM and credit card has been installed and
spread out to simplify the activity for financial activity, the banking
activity has been simplified, however the crime related with financial
organization has been increased in proportion to the ratio of spread
out of automation and devices.so that the cases of theft and robbery
have been increased gradually during past 12 years. Therefore, this
study is going to suggest the method of rapid reaction and
minimization of loss by detecting the ATM machine at real-time when
it has been stolen can be found through GSM technology. So by using
the GSM technology, Vibration sensor, DC Motor , unconscious gas
theft of external ATM machine can be predicted. In this project we are
using buzzer to give signal for corresponding bank and police station.
Camera is used to take the continuous video clips. Here DC Motor is
used to close the door of the ATM and relay is used for emit gas and
bring the theft to unconscious stage.
EXISTING SYSTEM

EXISTING SYSTEM:In the existing system, if any of the


sensors activates, then the alert message sent to the
authorized person. If anybody wants to verify the
previous sensor data at any particular time, there was
no chance. To avoid this we are incorporating the SD
card, in which the sensors data was stored.
PROPOSED SYSTEM
DESIGN CONSIDERATIONS

Block diagram
HARDWARE REQUIREMENT
•Arduino
•RTC Module
•L293D
•DC Motor
•GSM
•LCD
•Relay
•DC Fan
•Buzzer
•Vibrating Sensor
•SOFTWARE:
•Arduino IDE
ADVANTAGES AND APPLICATIONS
Advantages:
1. This system can monitor remote area ATM machine from theft.

2. It can avoid fire accidents.

3. We can see status of ATM machine through web server.

4. It can capture image of person who is trying to theft ATM machine

5. It can spray some kind of GASs on person who trying to theft ATM machine

Applications:
1.ATM applications
2.Security applications
3.All security applications
RESULT
Result:
The project was successfully developed and tested for
the performance. The results obtained are as
expected
FUTURE SCOPE:
In future we will use Raspberry Pi 3 processor as
a core, which has in-built Wi-Fi module using
which the
sensors data was sent to the web server like
Thingspeak to monitor the sensor data in
graphical format.
To do this we should provide internet to the
Wi-Fi module.
Anyone can monitor the sensor details
from anywhere in the world by opening the
server
CONCLUSION:
As we all know, these days most of the ATM has been
attacked by the robberies. Also gradual increases the
theft of ATM after the year by year. This paper
demonstrates how an automation of “ATM THEFT”
prevention from robbery (or) thief can be implemented
using GSM Technology, vibrating sensor, dc motor, stepper
motor, LED display, buzzer with keil micro vision 3.0 can
be implemented in ATM Machines centre. By implementing
this project, we can catch thief and robberies in ATM itself
and also we can save our precious time.
REFERENCE

• [1]. Sakr, Sharif. "ARM co-founder John Biggs". Engadget. Retrieved December 23,
2011. "[...] the ARM7-
• TDMI was licensed by Texas Instruments and designed into the Nokia 6110, which
was the first ARM-
• powered GSM phone."
• [2]. electricmotors.machinedesign.com
• [3]. Kim, Bo-Ra, “Domestic ATM status and meanings”, Payment and
Settlement, and IT, Vol. 44, pp. 76,
• 2011.
• [4]. Karki, James (September 2000). "Signal Conditioning Piezoelectric Sensors"
(PDF). Texas Instruments.
• Retrieved 2007-12-02.
• [5]. "GSM UMTS 3GPP Numbering Cross Reference". ETSI. Retrieved 30 December
2009.
• [6]. "Gsmd – Openmoko". Wiki.openmoko.org. 8 February 2010. Retrieved 22 April
2010.
Thank you

You might also like