GUI manual

OE14-208

OE14-208 Sales and Service:

Campus 1
Science and Technology Park
Aberdeen
Underwater Digital Stills Camera Scotland

tel: +44 (0)1224 226500 (24 hrs)

fax: +44 (0)1224 226501
User Manual Contents 2 Software Installation
3 GUI Operation Manufacturing:
4 File Menu Airport Industrial Estate
5 Camera Menu Wick
7 View Menu Caithness

8 Video Menu Scotland

10 Capture Menu
12 Help Menu tel: +44 (0)1955 603606
fax: +44 (0)1955 607520
13 Toolbar
15 Camera Tab
17 ADV Tab
19 Replay Tab
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Software Installation

The minimum computer requirements to operate the GUI is:

Pentium class computer, 300Mhz or above
Windows 98 SP2, Windows 2000 or Windows XP
Direct X V7.0 or V8.0 (V8.0 preferred)
64Mb Ram and 10Mb free hard disk space.
Mouse or other pointing device
CD-ROM drive
One free RS232/485 port or USB port.

To display video the requirement is increased by:

Video capture card compatible with Direct X 7.0 or above.

Capturing live video increase the demand on computer hardware. The specification is dependant
upon the resolution and compression method but for VGA capture the recommended computer
specification is:

Pentium III/700Mhz or greater with 128Mb ram and 250Mb free hard disk space
DMA-66 or faster hard disk drive

Ensure that if any previous version of the 14-208 GUI has been installed on the PC that it is
uninstalled before installation of any other version. To do this go into control panel and run
add/remove programs.

Inset the CD containing the GUI onto the computer. The disk will normally autoplay unless autoplay
has been disabled on that PC. If it does not autoplay load windows explorer and explore the CD,
open the folder marked GUI and run the set-up program. The installation program will then run.
Follow the instruction on screen to install the GUI.

Kongsberg Simrad Ltd Page 2 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

GUI Operation

When the GUI runs it displays a dialog box asking the user to select a comm port. The choices are
comm1 through comm 4. Select which port that the camera is plugged into. If the camera is not
connected to this port an error message will appear and most options on the GUI will be greyed
out. However the user will be able to change comm ports and reset the camera/GUI. If the camera is
connected to the selected comm port then the initialisation commands are then sent. These set the
camera up to default mode.

Figure 1.0

Power on default for the camera/GUI are:

Auto exposure mode.

Auto focus mode.
LLD remains unchanged.
Camera’s video output on.
GUI video display on.

The following pages detail all the functions of the GUI and explain what each option does. For
further assistance please help the help file on the GUI.

Kongsberg Simrad Ltd Page 3 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Menus

File Menu

Figure 1.1

Save file As: This option allows the changing of the filename where video is to be saved.

Exit: This will tell the camera to shut down and exit the GUI.

Kongsberg Simrad Ltd Page 4 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Camera Menu

Figure 1.2

Comm Port: Selects comm port to talk to 14-208 camera. The options are:

Comm 1: Selects comm1 and re-establishes communication on that port.

Comm 2: Selects comm2 and re-establishes communication on that port.
Comm 3: Selects comm3 and re-establishes communication on that port.
Comm 4: Selects comm4 and re-establishes communication on that port.

Note that if the comm port is changed and the camera is not connected to the selected port the GUI
reverts back to the previously selected port. When communications is established the camera and
GUI are set to power on defaults.

Flash: Turns the flash on or off.

Flash Off: Turns off the connection to an external flash.

Flash On: Turns the connection to the flash on. It will put 24V on to the external connector so if a
flashgun or a blanking plate is not fitted to the external connector the connector’s pins
may corrode.

Kongsberg Simrad Ltd Page 5 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Long Line Drive: Allows for compensation to video signal due to deterioration over long cable
lengths.

No compensation: Long line drive is off – setting 0.

200m: Signal is enhanced to compensate for 200m cable length – setting 1.
400m: Signal is enhanced to compensate for 400m cable length – setting 2.
750m: Signal is enhanced to compensate for 750m cable length – setting 3.
800m: Signal is enhanced to compensate for 800m cable length – setting 4.
1000m: Signal is enhanced to compensate for 1000m cable length – setting 5.
1100m: Signal is enhanced to compensate for 1100m cable length – setting 6.
1200m: Signal is enhanced to compensate for 1200m cable length – setting 7.
1200m*: Alternative option for 1200m compensation – setting 8.
1200m#: Alternative setting for 1200m compensation – setting 9.

Changing these values on the GUI has exactly the same effect as changing them using the remote
control. When the setting is changed a tick mark appears beside it on the menu. This setting will be
stored in the camera even if the camera is powered down or reset.

Mode: Set up camera operating mode, options are:

Automatic: Camera is in auto mode. Shutter speed and aperture size is set
automatically by the camera.
Aperture Priority: Camera is in aperture priority mode. Aperture is adjustable by user with
shutter speed being automatically set by camera.
Manual: Camera is in full manual mode. Shutter speed and aperture size are both
adjustable by user.
Program AE: Camera is in program automatic mode. It is similar to auto mode but
more options are user selectable (such as WB).
Shutter Speed Priority: Camera is in shutter priority mode. Shutter speed is adjustable by user,
aperture size is set automatically by camera.

Reset: Resets the camera and GUI to power on defaults.

When a setting is chosen a check mark appears beside it. The default setting is auto. If the mode is
changed certain settings such as WB may be changed. Certain modes restrict the features that are
available for the user to select, such as manual focus. For a full list of what settings are available in
each mode see the Canon G3 user manual. The GUI will grey out the features that are not available
in that mode.

Kongsberg Simrad Ltd Page 6 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

View Menu

Figure 1.3

Fit to Window: Video is scaled up to fit available resolution. The ratio of vertical to horizontal is the
same as that of the preview resolution.

Stretch to Window: Video is stretched to fit available area. The ratio of vertical to horizontal is not
necessary the same as that of the preview resolution.

200%: Video is scaled up to 200% of preview resolution.

100%: Video is displayed on screen at 100% of preview resolution.
75%: Video is scaled down to 75% of preview resolution.
50%: Video is scaled down to 50% of preview resolution.

Full Screen: Video is displayed over the full screen. Nothing else is visible. Click the left mouse
button to exit full screen mode.

Kongsberg Simrad Ltd Page 7 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Video Menu

Figure 1.4

Video Device: This options shows a list of compatible video devices installed on the computer.
Select the device which the 14-208’s video output is connected to.

Video Compressor: This option shows a list of encodings codec’s used for setting the format of
any video that is captured. The contents of the list depends on the codec’s installed on the PC.
Different codes give different resolution, compression, frame rates and file sizes. Choose the one
which most suitable. If you need more information on codec’s visit the appropriate web site. If there
is known to be an incompatibility between the GUI and a particular codec then a warning message
is displayed if it is selected.

Video Processor: This options allows any video processing options to be added. At present none
are supplied with the GUI.

Preview: This option allows the selection of 2 options, Preview enable and Disable while editing
properties. Selecting each option will change it from being on to off or vice versa. Preview enable
displays the video from the camera on the GUI. Selecting disable while editing properties will stop
the video when it’s display options are being changed.

Kongsberg Simrad Ltd Page 8 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Video Capture Size: This option allows the selection of the resolution that the video is shown at.
Selection of a resolution that the video card is not capable of displaying will result in the GUI
potentially becoming unstable. Common resolution are 320 * 240 (1/2 VGA) and 640 * 480 (VGA).
VGA resolution is recommend as it gives a larger and more detailed picture than ½ VGA. However it
requires more processing power and frame rate may be lower.

Video Capture Properties: This option allows the adjustment of the videos capture properties. The
options that are available depend on the driver installed for the video capture card. Typical
examples include frame rate and quality.

Preview Properties: This option is very similar to that of the video capture properties but it deals
with the display of the video. Typical options include frame rate, quality, source and format.

Video Compressor Properties: This option is only available when a video compressor has been
chosen and it has parameters that can be adjusted. Typical properties include compression levels.

Legacy Properties: This option allows several legacy options to be adjusted but in most cases this
option is not available.

Kongsberg Simrad Ltd Page 9 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Capture Menu

Figure 1.5

Video: This command allows for the capture of live video. Video will be saved to the file that has
been allocated. An option box is displayed containing two options. The first is a time limit. If this
option is selected then a number should be entered. This is the time (in seconds) that video will be
recorded for. If this option is not selected video will be recorded until the stop command is sent. If
the frame rate option is selected then the number entered is the frame rate that the GUI will try to
capture at. This rate is not guaranteed due to computer performance. If this option is not selected it
will try to capture at the preview frame rate.

Manual Frame Sequence: This command allows individual frames to be added to a video file. A
box comes up with a button on it called capture frame. When pressed it adds the current frame to a
video file. A counter is shown to show the number of frames captured. It is recommended that the
preview resolution is set to 320 *240 to allow the live video to be displayed at an acceptable frame
rate. Click on stop capture when frame capture is complete.

Auto Frame Capture: This command will automatically capture a sequence of frames. One option
is presented. If the time limit is selected, a number should be entered which is the number of frames
per second that are captured. If this option is not selected the video will be captured at the preview
frame rate, typically 15 frames per second. To stop the frame capture the stop command must be
pressed.

Kongsberg Simrad Ltd Page 10 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Frame to Clipboard: This option captures the current frame to the clipboard. It is captured at the
current preview resolution. Note the quality of this image is much less than that of a photo taken
with the 14-208 camera, even when the 14-208 is set to VGA resolution.

Stop Capture: This option will stop video or frame capture.

Kongsberg Simrad Ltd Page 11 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Help Menu

Figure 1.6

Help Topics: Uses windows help system to bring up a list of help topics for the GUI.

About: Brings up an about box with information about the GUI.

Kongsberg Simrad Web Site: Launches the Kongsberg web site in the PC’s default web browser.
This requires access to the Internet.

Kongsberg Simrad Ltd Page 12 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Toolbar Buttons

Figure 2.0

Preview: This button toggles the video display on/off.

Record: The button allows the camera’s video to be recorded to hard disk. It is the same as
selecting video from the capture menu.

Stop: This button stops the recording of video or frames.

Frame: This option will copy the current frame to the clipboard.

Snap: This activates the shutter on the camera and takes a photo when clicked. If the camera is in
auto focus mode it is recommended to get an AF lock before activating the shutter.

AF Lock: This creates an Auto Focus lock on the current scene. It is recommended that this is
done before a photo is taken when in auto focus mode. Do not release the button until green test
appears on the camera’s display, showing the focus setting.

Kongsberg Simrad Ltd Page 13 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Camera Status:

This displays the current status of the communication status between the GUI and the camera. The
options are.

Initialising: The GUI is trying to connect to the camera.

Failed: The camera has not been able to contact the camera
Connected: The GUI has successfully established communications with the camera.

At the bottom of the screen there is the word humidity with a dot beside it. If the dot is black then it
is within safe operating parameters. Otherwise the humidity is too high and the dot will go red. If it is
red then it is very highly recommended that new desiccant is put in the camera. Otherwise this may
result in serious damage to the camera. Other information displayed on the status bar include the
capture device, audio status and information on any video/frames that have just been recorded.

Kongsberg Simrad Ltd Page 14 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Tab Strip

Camera Tab: When this tab is active then the camera is in photo mode. It contains all the basic
options needed to operate the camera.

Figure 3.0

Zoom Plus: Pressing this button will cause the camera to zoom in (tele). It will continue zooming in
until the near zoom limit is reached or until the button is released.

Zoom Minus: Pressing this button will cause the camera to zoom out (wide). It will continue
zooming out until the far zoom limit is reached or until the button is released.

Auto Focus: Selecting this option will cause the camera to operate in auto focus mode. The manual
focus buttons will be greyed out.

Manual Focus: Selecting this option will cause the camera to operate in manual focus mode. The
availably of this option depends on which mode the camera is operating in. When in manual focus
mode, the focus near and focus far buttons become available. To exit manual focus mode just click
auto focus.

Focus Far Button: Clicking this button causes the camera to focus near one increment.

Focus Near Button: Clicking this button causes the camera to focus far one increment

Kongsberg Simrad Ltd Page 15 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Macro: This enables macro focus mode for close up photography work. This option is available in
both manual and auto focus modes.

S/A Button: When the camera is operating in manual mode both shutter speed and aperture value
is adjustable. This swaps between them.

Shutter Plus Button: This button will increase the shutter speed. Every time it is clicked the shutter
speed will increase one increment until the maximum shutter speed is reached. It also doubles as
the aperture increase button.

Shutter Minus Button: This button reduces the shutter speed. Every time it is clicked the shutter
speed will reduce one increment until the minimum shutter speed is reached. It also doubles as the
aperture decrease button.

Note some of these buttons will not always be available as it depends on which mode the camera is
operating in. See the Canon G3 manual for more details.

Menu Button: Clicking once on this displays the cameras built in menu. Clicking it for a second
time closes the menu. The menu allows the user to adjust various camera settings. See the Canon
G3 manual for more details.

Up Arrow Button: This is the up arrow for scrolling the camera’s menu.

Down Arrow Button: This is the down arrow for scrolling the camera’s menu.

Left Arrow Button: This is the left arrow for scrolling the camera’s menu.

Right Arrow Button: This is the right arrow for scrolling the camera’s menu.

Set Button: Click this to press set, which confirms the current selection.

Kongsberg Simrad Ltd Page 16 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

ADV Tab: This tab allows access to some of the more advanced camera functions.

Figure 3.1

Func Button: Clicking this automatically puts the camera in a mode where several options can be
adjusted. This includes WB, images size and flash exposure compensation. Further details of what
options are available see the G3 manual.

Up Arrow Button: Click this to go through the list of options, moving up.

Down Arrow Button: Click this to go through the list of options, moving right.

Left Arrow Button: Click this to go through the list of options, moving left.

Right Arrow Button: Click this to go through the list of options, moving right

Set Button: Click to set the currently selected option

Kongsberg Simrad Ltd Page 17 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Flash Mode Button: This button cycles through the list of flash mode option. Each time the button
is pressed the next mode is selected. The choices that are listed depend on what mode the camera
is operating in. This option will do nothing if the OE11-242 flashgun is not fitted. The list of options is
not displayed on the screen

Spot Meter Button: Clicking this button activates the spot meter exposure option.

Display Button: Click this once to turn then cameras display overlay off. Another press turns the
video display off and a third press turns turn it all back on.

AE Lock Button: Clicking this button engages an AE lock on the current scene.

Roller Left: Clicking this button turns the roller wheel on the camera one turn to the left.

Roller Right: Clicking this button turns the roller wheel on the camera one turn to the right.

Roller Push: Clicking this button pushes the roller wheel and then releases it.

Kongsberg Simrad Ltd Page 18 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Replay Tab: Clicking this tab puts the camera into replay mode so the previous taken images can
be viewed. By default the most recently taken photo is shown.

Figure 3.2

Left Arrow Button: Clicking this button cycles to the image taken before the currently displayed
image.

Right Arrow Button: Clicking this button cycles to the image taken after the currently displayed
image.

Plus Button: Pressing this button will zoom in on the currently selected image. Zooming will stop
when the button is released or it is not possible to zoom in any further.

Minus Button: Pressing this button will zoom out on the currently selected image. Zooming will
stop when the button is released or it is not possible to zoom out any further.

Multi Button: Clicking this button will display multiple images on the screen.

Jump Button: Clicking this button jump to the next set of images.

Kongsberg Simrad Ltd Page 19 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520
Manual OE14-208
JBA Explorer.lnk
GUI
colour
Underwater Digital Stills Camera

Erase Button: Clicking this options erases the current selected image(s).

Menu Button: Clicking once on this displays the cameras built in menu. Clicking it for a second
time closes the menu. The menu allows the user to adjust various camera settings. See the Canon
G3 manual for more details.

Up Arrow Button: This is the up arrow for scrolling the camera’s menu.

Down Arrow Button: This is the down arrow for scrolling the cameras menu.

Left Arrow Button: This is the left arrow for scrolling the cameras menu.

Right Arrow Button: This is the right arrow for scrolling the cameras menu.

Set Button: Click this to press set which confirms the current selection.

Kongsberg Simrad Ltd Page 20 of 20

GUI Manual: OE14-208 Underwater Digital Stills Camera - 5024 - 1

Sales and Service: Campus 1, Science and Technology Park, Aberdeen, Scotland Manufacturing: Airport Industrial Estate, Wick, Caithness, Scotland
tel: +44 (0)1224 226500 (24 hrs) fax: +44 (0)1224 226501 tel: +44 (0)1955 603606 fax: +44 (0)1955 607520