Scribd
Upload
115 views5 pages

DLD Final Project Shahid Abbas

This document is a project submission for a cell phone signal jammer. It was submitted by five students to their professor at COMSATS University Islamabad Vehari Campus. The project involves building a device that can disrupt the communication between a mobile phone and cell tower by transmitting signals on the same frequencies. It describes the components used, including a PCB board, NE555 IC, capacitors, transistor, resistor, battery, and provides diagrams of the PCB board layout and circuit diagram.

Uploaded by

Shahid Abbas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
115 views5 pages

DLD Final Project Shahid Abbas

This document is a project submission for a cell phone signal jammer. It was submitted by five students to their professor at COMSATS University Islamabad Vehari Campus. The project involves building a device that can disrupt the communication between a mobile phone and cell tower by transmitting signals on the same frequencies. It describes the components used, including a PCB board, NE555 IC, capacitors, transistor, resistor, battery, and provides diagrams of the PCB board layout and circuit diagram.

Uploaded by

Shahid Abbas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

DLD FINAL PROJECT

Project name :

CELL PHONE SIGNAL JAMMER


Subject :

DLD
Submitted by :

(Shahid abbas ),( Hanzala Javed ), (Ali Anus) , (Waseem Bhatti),(Muhammad


Bilal)
Roll number:

Fa20- bse --078,,,024,,,,030,,,044,,,068


Section:

(B)
Submitted To:

Sir Ammar Yassir Sab

COMSATS UNIVERSITY ISLAMABAD

VEHARI CAMPUS
CELL PHONE SIGNAL JAMMER

WHAT IS SIGNAL JAMMER ?


A mobile phone jammer or blocker is a device which deliberately transmits signals on the same radio
frequencies as mobile phones, disrupting the communication between the phone and the cell-phone
base

COMPONENTS
 PCB BORD
 COPER WIRE
 NE555 IC
 2pf ,4.7pf ,3.3pf ,47pf CERAMIC CAPACITOR
 BF495 TRANSISTOR
 1uf 63V ELECTROLYTIC CAPACITOR
 30pf VARIABLE / TIMER CAPACITOR
 10k , 6.8k , 82k , 220e , 5.6k RISISTOR
 3PIN MINI SLIDE SWITCH
 LED
 2 PIN HEADER CONNECTOR
 9 V BATTERY
PCB

PCB or Printed Circuit Board is the traditional name for the bare board of which you supply
us with the layout data and which you use to mount your components on once we have
delivered it to you.
NE 555 IC

The 555 timer IC is an integrated circuit used in a variety of timer, delay, pulse generation, and
oscillator applications. Derivatives provide two or four timing circuits in one package.

COPPER WIRRE

 Copper wire is used in power generation, power transmission, power distribution,


telecommunications, electronics circuitry, and countless types of electrical equipment. Copper
and its alloys are also used to make electrical contacts.

CERAMIC CAPACITOR

A ceramic capacitor is a fixed-value capacitor where the ceramic material acts as the dielectric. It is
constructed of two or more alternating layers of ceramic and a metal layer acting as the electrodes.
The composition of the ceramic material defines the electrical behavior and therefore applications.
TRANSISTOR

A transistor is a semiconductor device used to amplify or switch electrical signals and power.
The transistor is one of the basic building blocks of modern.

ELECTROLYTIC CAPACITOR

These capacitors are great transient/surge suppressors and work well in high-voltage and
audio applications. High quality radial electrolytic capacitors.

TRIMMER CAPACITOR

Trimmer capacitors are used to initially set oscillator frequency values, latencies, rise and fall
times and other variables in a circuit. Should the values drift over time, these trimmer capacitors
allow repairmen to re-calibrate equipment when needed.
DIGRAM

You might also like