Installation,

Operation, and
Maintenance Instructions
with Troubleshooting
Electric Full Size Economy Convection Oven
Models:
FCOFL-AT (Lower)
FCOF-AT (Upper)

Lang Manufacturing 10 Sunnen Drive St. Louis, MO 63143

Part #: 2M-W731 Phone: 314-678-6315 Fax: 314-781-2714
Rev B www.langworld.com June 05, 2012
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ,
UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS
CONTAINED IN THIS MANUAL.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
POST IN A PROMINENT LOCATION
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS.
THIS INFORMATION SHALL BE OBTAINED BY CONSULTING YOUR LOCAL
GAS SUPPLIER. AS A MINIMUM, TURN OFF THE GAS AND CALL YOUR
GAS COMPANY AND YOUR AUTHORIZED SERVICE AGENT. EVACUATE
ALL PERSONNEL FROM THE AREA.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION,

SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY
OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS
EQUIPMENT.

Model #: Purchased From:

Serial #: Location:

Date Purchased: Date Installed:

Purchase Order #: For Service, Call:

2
 TABLE OF CONTENTS

CHAPTER PAGE
1. TABLE OF CONTENTS..........................................................................3

2. READ FIRST ..........................................................................................4

3. EQUIPMENT DESCRIPTION .................................................................6

4. UNPACKING ..........................................................................................7

5. INSTALLATION ......................................................................................8

6. INITIAL START-UP.................................................................................9

7. OPERATION...........................................................................................10

8. MAINTENANCE & CLEANING ...............................................................11

9. WIRING DIAGRAM.................................................................................16 – 17

10. ILLUSTRATED PARTS BREAK DOWN .................................................18 - 29

3
IMPORTANT READ FIRST IMPORTANT

CAUTION: EACH UNIT WEIGHS 275 LBS. FOR SAFE HANDLING,

INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR
EMPLOY APPROPRIATE MATERIALS HANDLING
EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET
JACK) TO REMOVE THE UNIT FROM THE SKID AND
MOVE IT TO THE PLACE OF INSTALLATION.
CAUTION: ANY STAND, COUNTER OR OTHER DEVICE ON WHICH
OVEN WILL BE LOCATED MUST BE DESIGNED TO
SUPPORT THE WEIGHT OF THE OVEN.
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.
DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE
TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION AND
DEATH.
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY.
IMPROPER INSTALLATION CAN CAUSE INJURY TO
PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT
MUST BE INSTALLED IN ACCORDANCE WITH ALL
APPLICABLE CODES.
NOTICE: The data plate is located behind circuit breaker door on
oven. The oven voltage, wattage, serial number, wire size,
and clearance specifications are on the data plate. This
information should be carefully read and understood
before proceeding with the installation.
NOTICE: The installation of any components such as a vent hood,
grease extractors, fire extinguisher systems, must
conform to their applicable National, State and locally
recognized installation standards.
NOTICE: During the first few hours of operation you may notice a
small amount of smoke coming from the oven, and a faint
odor from the smoke. This is normal for a new oven and
will disappear after the first few hours of use.
CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE
FROM COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND
DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY, TO
AVOID THE DANGER OF SLIPS OR FALLS.

4
IMPORTANT READ FIRST IMPORTANT

WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS.

NEVER SPRAY OR HOSE CONTROL CONSOLE,
ELECTRICAL CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES,
MUCOUS MEMBRANES AND CLOTHING. PRECAUTIONS
SHOULD BE TAKEN TO WEAR RUBBER GLOVES,
GOGGLES OR FACE SHIELD AND PROTECTIVE
CLOTHING. CAREFULLY READ THE WARNING AND
FOLLOW THE DIRECTIONS ON THE LABEL OF THE
CLEANER TO BE USED.
NOTICE: Service on this, or any other, LANG appliance must be
performed by qualified personnel only. Consult your
LANG authorized service agent directory or call the
factory at 314-678-6315, or www.langworld.com for the
service agent nearest you.
WARNING: BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE
THIS APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED
INTO A LIVE RECEPTACLE. BEFORE REPLACING ANY
PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC
POWER SUPPLY.
CAUTION: USE OF ANY REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE
OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

5
 EQUIPMENT DESCRIPTION

Model: FCOFL-AT/FCOF-AT

Exterior Construction
The oven exterior dimensions are 36” (91.44cm) Wide, 22” (55.88cm) High,
34” (86.36cm) Deep. The Front, Back, and Sides are constructed of stainless
steel with an aluminized top and bottom.
The door handle is constructed of Polycarbonate.
The oven cavity is insulated with high temperature insulation for efficiency and
reduced heat loss.

Interior Construction
The oven cavity dimensions are 20” (50.8cm) Wide, 17” (43.18cm) High, 29”
(73.66cm) Deep.
The oven is designed for three shelves and comes with three Chrome Plated
Racks.
The interior of the oven is constructed of aluminized steel.

Operation
The oven is a forced air convection oven with a vented oven cavity.
The air is driven by a 1/3 HP fan motor.
Controls
Easy to use manual control knobs.
Mechanical temperature sensing and controls.

Technical
Oven operates as shipped on 208, 240, or 480-Volt Single, or Three Phase.
Floor space required is 42” (106.68cm) Wide, 37” (94cm) Deep.
The oven weighs 275 lb.
The ovens are stackable and can include stacking kit if requested.

6
 UNPACKING
Receiving the Oven
Upon receipt, check for freight damage, both visible and concealed. Visible
damage should be noted on the freight bill at the time of delivery and signed
by the carrier's agent. Concealed loss or damage means loss or damage,
which does not become apparent until the merchandise has been unpacked.
If concealed loss or damage is discovered upon unpacking, make a written
request for inspection by the carrier's agent within 15 days of delivery. All
packing material should be kept for inspection. Do not return damaged
merchandise to Lang Manufacturing Company. File your claim with the
carrier.
Location
Prior to un-crating, move the oven as near to its intended location as
practical. The crating will help protect the unit from the physical damage
normally associated with moving it through hallways and doorways.
Un-crating
The oven will arrive completely assembled inside a wood frame and
strapped to a skid. Cut the straps and remove the wood frame.

CAUTION: THE OVEN WEIGHS 225 LBS. FOR SAFE HANDLING,

INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR
EMPLOY APPROPRIATE MATERIALS HANDLING
EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET
JACK) TO REMOVE THE UNIT FROM THE SKID AND
MOVE IT TO THE PLACE OF INSTALLATION.
CAUTION: ANY STAND, COUNTER OR OTHER DEVICE ON WHICH
THE OVEN WILL BE LOCATED MUST BE DESIGNED TO
SUPPORT THE WEIGHT OF THE OVEN.
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.

Remove Oven from skid and place in intended location.

7
 INSTALLATION

DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE

TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION AND
DEATH.
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY
AND PLUMBING. IMPROPER INSTALLATION CAN
CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO
EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.
NOTICE: The data plate is located behind circuit breaker door on
oven. The oven voltage, wattage, serial number, wire size,
and clearance specifications are on the data plate. This
information should be carefully read and understood
before proceeding with the installation.
NOTICE: The installation of any components such as a vent hood,
grease extractors, fire extinguisher systems, must
conform to their applicable National, State and locally
recognized installation standards.

Leg Installation
Legs are available for single, double, and triple, installations. Single deck
installations require a 27-inch leg, double deck installations require a 16-inch
leg, and triple deck installations require a 6-inch leg.
To install the 27-inch legs, place some cardboard on the floor and gently tip the
oven onto its back. Fasten two legs to the oven's front. Lift the oven onto its
front legs and block the back up using one of the 27-inch legs set upside down
in the center rear of the oven body. Install the last 27-inch leg onto the oven
body on the control side rear. Gently lift the oven rear, remove the leg set to
support the oven center and install it on the last rear corner.
To install the 16-inch legs follow the same instructions as the 27-inch legs and
then proceed to “Stacking the Ovens” for the second deck installation.
To install the 6-inch legs, place some cardboard on the floor and gently tip the
oven onto its back. Fasten the four 6-inch legs onto the bottom of the oven.
Gently lift the oven onto the legs and proceed to the “Stacking the Ovens” for
the second and third deck installation.

8
 INSTALLATION

Stacking the Ovens

Stacking kits must be requested upon purchase.
Remove all the plug buttons from the top of the lower oven.
Remove the stacking kit from the oven compartment of one oven and install the
1 1/4-inch plastic bushing into the top of the lower oven.
Tip the top oven backwards and install two pins into the front leg holes of the top
oven.
Route the wires 1 and 2 from the upper deck through the 1 ¼-inch knockout in
the bottom of the oven through the 1 ¼-inch knockout in the top of the bottom
oven to the main terminal block in the bottom oven. Refer to wiring diagram for
proper phasing.
Lift the top oven and gently set on top of the lower oven so that the studs nest
into the holes of the lower oven.
If placing a range top onto the oven, see the installation section of the range top
for installation directions.
Electrical Connection
The electrical connection must be made in accordance with local codes or in the
absence of local codes with NFPA No. 70 latest edition (in Canada use: CSA
STD. C22.1).
The electrical service entrance is provided by a 1 1/4-inch knockout on the oven
bottom. A three pole terminal block is provided for connection.

INITIAL START-UP
INITIAL PREHEAT
Prior to putting any oven into full time operation at normal cooking
temperatures, it must be thoroughly dried out. Moisture absorption in the
closed spaces, in the insulation, and even inside the heating elements can
cause future trouble if not properly treated.
To “dry out” the oven, set the thermostat to 250°F and turn on the power
switch. Allow the unit to cycle at least 15 minutes at this heat level. Reset the
thermostat to 350°F allow the same time. Reset the thermostat to 450°F and
allow the unit to maintain the temperature for a minimum of 4 hours. More
time may be required if the unit has to operate in moist environment.
If the unit is out of use for three or more days, a one-hour preheat schedule
should be used, especially when exposed to high humidity and/or cool
temperatures.

NOTICE: During the first few hours of operation you may notice a
small amount of smoke coming from the oven, and a
faint odor from the smoke. This is normal for a new
range and will disappear after the first few hours of use.

9
 OPERATION

CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE

FREE FROM COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND
DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY, TO
AVOID THE DANGER OF SLIPS OR FALLS.

General Operation
The convection oven roasts and bakes in shorter time and at lower
temperatures with less shrinkage than conventional commercial ovens.
A blower in the Lang convection oven circulates air within the chamber to heat
the entire space evenly and transfer heat efficiently to the product, even with
stacked loading.
The airflow continuously removes the thick layer of moist, cool air that otherwise
would surround the product. When properly loaded and operated, it maintains
this airflow throughout the chamber to eliminate hot spots and roasts or bakes
with minimum power consumption at twice the output capacity of a conventional
oven.
The power switch on the lower portion of the control panel energizes the fan
motor and activates the thermostatically controlled circuit for the oven heating
elements. When this switch is in the on position, the red indicator light will
illuminate.
Rotating the thermostat control knob from "off" position to selected temperature
causes the indicator light to illuminate and closes the contactor that feeds power
to the heating elements. This light will cycle "on and off" as the thermostat calls
for heat in the oven. The blower, however, operates continuously while the
power switch is in the "on" position.
The black control knob operates a damper in the oven vent stack. Damper is
open when knob is pulled outward.
Circuit breakers behind the control panel protect the electrical components from
overload.

Typical Operation

ACTION RESULT
Turn power switch to ON. Control panel heat call light comes on.
Adjust proper temperature, between 140°F& Oven begins heating.
450°F and allow preheating for 20 minutes.
Open oven doors and insert product. Set timer Timer begins counting down.
for up to 60 minutes.
Timer rings when done. Product should now be done.

10
 MAINTENANCE & CLEANING

Cleaning
WARNING: KEEP WATER AND SOLUTIONS OUT OF
CONTROLS. NEVER SPRAY OR HOSE
CONTROL CONSOLE, ELECTRICAL
CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN,
EYES, MUCOUS MEMBRANES AND CLOTHING.
PRECAUTIONS SHOULD BE TAKEN TO WEAR
RUBBER GLOVES, GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. CAREFULLY READ THE
WARNING AND FOLLOW THE DIRECTIONS ON THE
LABEL OF THE CLEANER TO BE USED.
The oven should be thoroughly cleaned at least once a week in addition to the
normal daily cleaning to insure against the accumulation of foreign material.
• Always start with a cold oven.
• The stainless exterior can easily be cleaned using stainless steel cleaner
• Always follow the cleaner manufacturer's instructions when using any
cleaner.
• Care should be taken to prevent caustic cleaning compounds from coming
in contact with the blower wheel.
• The oven racks, rack slides, and interior may be cleaned using oven
cleaner.
• Discoloration or heat tint may be removed using a Carbon Release oven
cleaner.
• The oven interior should be cleaned using a mild soap and a non metal
scouring pad. DO NOT use caustic cleaners.
Always apply these cleaners when the oven is cold and rub in the direction
of the metal's grain.
Electric equipment is inherently clean and sanitary, but may become
unsanitary if grease is allowed to accumulate on it. Take advantage of the
clean, sanitary features of electric equipment, give it the regular attention
that it deserves the same as any other highly perfected machinery, to insure
best results and continued high operating efficiency.

11
 MAINTENANCE & CLEANING

TROUBLE SHOOTING
Symptoms
What follows is a chart of Symptoms, Possible Causes, and Remedy’s to
aid in diagnosing faults with the oven.
Refer to the Symptoms column to locate the type of failure then to the
Possible Cause for the items to be checked and the Remedy to column for
possible solutions.

SYMPTOM POSSIBLE CAUSE

Oven will not heat Oven circuit breaker not on
Incorrect wiring
Defective transformer
Defective fuses
Defective contactor
Defective thermostat
Defective element
Oven motor will not run Incorrect wiring
Defective transformer
Defective fuses
Defective contactor
Defective motor
Product burning Product cooked too long
Oven out of calibration
Defective transformer
Product under cooked Product not cooked long enough
Oven out of calibration
Defective thermostat

12
 MAINTENANCE & CLEANING
TESTS
NOTICE: Service on this, or any other, LANG appliance must be
performed by qualified personnel only. Consult your
LANG authorized service agent directory or call the
factory at 1-800-807-9054, or WWW.STAR-MFG.COM
For the service agent nearest you.
WARNING: BOTH HIGH AND LOW VOLTAGES ARE PRESENT
INSIDE THIS APPLIANCE WHEN THE UNIT IS
PLUGGED/WIRED INTO A LIVE RECEPTACLE.
BEFORE REPLACING ANY PARTS, DISCONNECT THE
UNIT FROM THE ELECTRIC POWER SUPPLY.

If an item on the list is followed by an asterisk (*), the work should be done by a
factory authorized service representative.

Possible Cause TEST

Oven circuit breaker not on Cycle breaker to the “ON” position.
Incorrect wiring Confirm that oven is getting proper voltage*
Confirm that oven is phased correctly*
Defective transformer Confirm that primary coil has the correct
voltage*
Confirm that secondary coil has the correct
voltage*
Defective fuses Replace fuses
Defective contactor Confirm that contactor coil has correct
voltage*
Confirm that contactor points move freely
Defective thermostat Confirm that thermostat has correct voltage*
Confirm that thermostat is operating properly
Defective element Confirm that elements has correct voltage*
Confirm that elements are pulling correct
amps*
Defective motor Confirm that motor has correct voltage*
Confirm that motor is pulling correct amps*

CAUTION: USE OF ANY REPLACEMENT PARTS OTHER THAN

THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE
OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

13
 MAINTENANCE & CLEANING

CALIBRATION
Calibration Check
Place thermometer or thermocouple in the center of oven cavity.
Set thermostat to 350°F.
Allow the oven to Preheat for at least half an hour.
Note cycle on temperatures and cycle off temperatures for 3 cycles. (Red indicator light
indicates when oven is calling for heat)
After 3 cycles average the temperature. (Add all six temperatures and divide by 6)
Calibration Adjustment
A 1/16” flat blade screwdriver with a 2” shaft is required to make adjustments on the
thermostat.
Maintain the oven temperature at 350°F.
Without turning the thermostat, remove the knob.
Locate the adjustment screw at the base of the shaft and insert the screwdriver.
Grasp the shaft and turn the screw. Counter clockwise to increase and clockwise to
decrease (1/8 of a turn will move the temperature 5-7 ° in either direction).
Reinstall the oven knob and recheck the oven temperature.

REMOVAL INSTRUCTIONS
Thermostat, Contactor, Transformer, and Switch
These parts are located behind the control panel assembly on the right hand side of the
oven. To access control panel secure unit from power, remove the vent knob and the
seven screws around the outside of the control panel assembly. Slowly pull the control
panel toward you until the component is accessible.

Thermostat
Secure oven from power. Inside the oven, remove the fan baffle and the retaining clips
holding the thermostat capillary tube to the inside of the oven. Feed the bulb through the
oven wall into the control panel area. Pull out control panel as previously outlined.
Remove the wires from the old thermostat and attach to the corresponding terminal of
the new thermostat. Remove knob and two screws that hold the thermostat to the oven
control panel. Discard old thermostat. Reinstall the thermostat and capillary tube into
oven and the control panel and restore power to the oven. Test for proper operation.

Contactor and Switch

Pull out control panel as previously outlined. Remove the wires from the contactor or
switch being changed. Place those wires on the corresponding terminal of the new
contactor or switch. Remove old contactor or switch and mount new contactor or switch
with wires attached. Discard old contactor or switch. Reinstall the control panel and
restore power to the oven. Test for proper operation.

Transformer
Pull out control panel as previously outlined. Remove the wires from the old transformer.
Place the wires on the corresponding terminal of the new transformer. Remove old
transformer and mount new transformer with wires attached. Discard old transformer.
Reinstall the control panel and restore power to the oven. Test for proper operation.

14
 MAINTENANCE & CLEANING

Blower Wheel
Secure oven from power. Inside the oven, remove the racks and right hand rack slide.
Remove wing nut holding oven baffle. Remove oven baffle exposing the blower wheel.
Loosen the two 1/4-20-set screws holding the blower wheel to the motor shaft. Using a
three-fingered wheel puller, grasp the puller ring with all three fingers and tighten the
puller until the blower wheel hub clears the motor shaft. Place new blower-wheel on the
motor shaft and position the new blower wheel so that it is flush with front inlet ring.
Tighten the set-screw over the flat spot on the motor shaft and spin the blower wheel to
confirm that blower wheel is strait. Adjust if necessary and tighten second set screw.
Test for proper operation.

Motor
Remove the blower wheel as outlined above. Once blower wheel is removed, remove
the six bolts holding the motor plate to the side wall of the oven. Gently pull the motor
out and lay on the bottom of the oven cavity. Note each wire location on the motor and
remove the wires. Remove motor from cavity and remove old motor from motor
mounting plate. Attach new motor to motor mounting plate. Reverse removal
instructions to assemble. Discard old motor and test for proper operation.

Elements
Remove oven racks and right hand rack slide from oven. Remove the wing nuts holding
oven baffle to right hand of oven. Remove oven baffle from oven. Remove 4 screws
holding oven elements to right hand of oven. Gently pull elements away from right hand
of oven. Noting wire locations disconnect wires from element. Discard old element.
Reverse removal instructions to assemble.

15
 WIRING DIAGRAM 208/ 240

16
 WIRING DIAGRAM 480

17
 1 4

2
17
16

15

18

SEE CAN ASSY

14

13

12 3

11

10
19
20

9
7
SEE
CONTROLS 13 20
ASSY
Marine Application

8
5
SEE
DOOR ASSY 6

Model:
FCOF & FCOFL MAIN ASSEMBLY
F6S MAIN ASSEMBLY SK2288 Rev. - 7/30/07
PARTS LIST November 20, 2013, Rev B

Model No: FCOF & FCOFL

Commercial & Marine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description

1 Q9-F6-160 1 TOP A/L ALL FCOFL MODELS

Q9-F6-160-1 1 TOP S/S ALL FCOF MODELS
2 2H-F6-259 1 INSULATION-TOP REAR ALL MODELS
3 Q9-F6-148 1 BODY ASSEMBLY ALL MODELS
4 2H-F6-260 1 INSULATION-REAR FILLER ALL MODELS
5 2H-F6-254 1 INSULATION- BOTTOM REAR ALL MODELS
6 2H-F6-253 1 INSULATION-BOTTOM FRONT ALL MODELS
7 Q9-F6-131 1 BOTTOM FRONT CHANNEL ALL MODELS
8 Q9-F6-137 1 SWITCH DOOR ALL MODELS
9 2F-70601-28 1 HINGE BRAKET LOWER LEFT ALL MODELS
10 Q9-F6-129 1 FRONT STD ALL MODELS
11 2F-70601-27 1 HINGE BRAKET UPPER LEFT ALL MODELS
12 Q9-F6-130 1 TOP FRONT CHANNEL ALL ALL MODELS
13 Q9-50301-52 1 “DOOR STOP LH ARM&BRACKET ASSY” FCOF 208M, 240M, 440G,AND 440M;
FCOFL 208M, 240M, 440G, 440M, 480G,
AND 480M
14 Q9-F6-132 2 HINGE NUT PLATE ALL MODELS
15 2H-F6-257 1 INSULATION- LEFT FRONT ALL MODELS
16 2H-F6-258 1 INSULATION-TOP FRONT ALL MODELS
17 2H-F6-256 1 INSULATION-LEFT REAR ALL MODELS
18 2H-F6-255 1 INSULATION-BACK ALL MODELS
19 2A-20503-01 4 5/16IDX27/640DX5/16LG STL ALL FCOFL MODELS
20 Y9-50300-63 1 MARINE PAN LATCH ASSY FCOF 208M, 240M, 440G,AND 440M;
FCOFL 208M, 240M, 440G, 440M, 480G,
AND 480M
NI 2B-50200-07 2 RACK SLIDE F6 OVEN
NI 2B-50200-64 3 OVEN RACK F6 STD
NI Q9-F6-127-1 2 RACK SLIDE CLIP B S/S
NI Q9-F6-126-1 6 RACK SLIDE CLIP A S/S

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
 1
30

3
29
28

26
27 31
25 SEE CAN ASSY

23
24
22
5

20 21 6

19

18
32
14
15
17

SEE 9
CONTROLS 13
ASSY 16

12

10

11
SEE
DOOR
ASSY

Model:
FCOF-SUBMARINE MAIN ASSEMBLY
F6S SUBMARINE MAIN ASSEMBLY SK2289 Rev. - 7/30/07
 PARTS LIST November 20, 2013, Rev B

Model No: FCOFAT480SUB SUBMARINE
Submarine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description

1 Q9-F6-160-3 1 TOP PART A SUB

2 Q9-F6-160-4 1 TOP PART B SUB
3 Q9-F6-260-1 2 INSULATION REAR FILLERS
4 Q9-F6-148-5 1 SPOT BODY BACK SUB
5 Q9-F6-251-1 1 R/H SIDE FRONT INSULATION
6 Q9-F6-252-2 1 RIGHT BOTTOM INSULATION
7 Q9-F6-152-1 1 FIREWALL SUB
8 Q9-F6-254-1 1 BOTTOM REAR INSULATION
9 Q9-F6-155-8 1 R/H BODY SIDE 430 S/S SUB
10 Q9-F6-149-2 1 BOTTOM PART B SUB
11 2A-72500-06 4 LEG 5 1/2W/BOLT DOWN ADJ
12 Q9-F6-149-1 1 BOTTOM PART A SUB
13 Q9-F6-253-1 1 BOTTOM FRONT INSULATION
14 2P-51001-12 1 SPRNGCOMPRSN.665IDX1.4LNG
15 Q9-F6-131 1 BOTTOM FRONT CHANNEL
16 Q9-F6-137 1 SWITCH DOOR
17 2F-70601-28 1 HINGE BRAKET LOWER LEFT
18 Q9-F6-129-1 1 F6 MIL. FRONT DOOR SWITCH
19 2F-70601-27 1 HINGE BRAKET UPPER LEFT
20 Q9-F6-130 1 TOP FRONT CHANNEL ALL
21 Q9-F6-206 1 SPOT SWITCH BRACKET
22 Q9-50301-52 1 “DOOR STOP LH ARM & BRACKET ASSY”
23 Q9-F6-132 2 HINGE NUT PLATE
24 2C-20101-17 2 SCRW RND MS 6-32X1 PLTD
25 Q9-F6-211 1 MICRO SWITCH MOUNT
26 2C-20301-10 2 NUT HEX 6-32 PLTD
27 2E-30301-02 1 SWITCH, MICRO
28 Q9-F6-259-1 1 TOP INSULATION SUB
29 Q9-F6-257-1 1 L/H SIDE INSULATION SUB
30 Q9-F6-155-7 1 L/H BODY SIDE 430 S/S SUB
31 2H-F6-255 1 INSULATION-BACK
32 Y9-50300-63 1 MARINE PAN LATCH ASSY
NI 2B-50200-07 2 RACK SLIDE F6 OVEN
NI 2B-50200-64 3 OVEN RACK F6 STD
NI Q9-F6-127-1 2 RACK SLIDE CLIP B S/S
NI Q9-F6-126-1 6 RACK SLIDE CLIP A S/S

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
 1

9 8

2
10

11
3

13

12
4
11
5
10
6
9 7
8

Model:
FCOF & FCOFL DOOR ASSEMBLY
F6S DOOR ASSEMBLY SK2290 Rev. - 7/30/07
PARTS LIST December 11, 2008, Rev B

Model No: FCOF & FCOFL Door Assembly
Commercial, Marine & Submarine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description

1 PS-50301-50-1 1 DOOR STOP ASSY L/H FCOFAT480SUB; FCOF 208M, 240M, 440G,AND
440M; FCOFL 208M, 240M, 440G, 440M, 480G,
AND 480M
2 Q9-F6-144-6 1 INSIDE DOOR PANEL S\S SUB FCOFAT480SUB; FCOF 480G; FLAT 480G,
FCOFLSL480VM
Q9-F6-144 1 INSIDE DOOR PANEL A/L FCOF 208M, 208V, 240M, 240V, 440M,480M, 480V;
FCOFL 208, 240, 480, 208M, 240M, 440G, 440M,
480M
3 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA ALL MODELS
4 2H-F6-144-1 1 DOOR INSULATION ALL MODELS
5 Q9-F6-146 2 STIFFENER - DOOR HANDLE ALL MODELS
6 2C-20115-04 AR SCRW S/S 6-32X3/8 S/T P/H FCOFAT480SUB; FCOF 480G; FLAT 480G
2C-20103-06 AR SCRW SM PLT 6 X 3/8 PHL FCOF 208M, 208V, 240M, 240V, 440M,480M, 480V;
FCOFL 208, 240, 480, 208M, 240M, 440G, 440M,
480M
7 2R-50800-12 1 DOOR T HANDLE 11 1/2 LNG ALL MODELS
8 2C-20109-13 AR SCRW MS SS 10-32 X .5 PH ALL MODELS
9 2F-70601-06 AR HINGE PIN, HALF HINGE ALL MODELS
10 2C-20202-17 AR WSHR LOCK FOR 70601-27/28 ALL MODELS
11 2F-70601-05 AR PLATE & BUSH HINGE HALF ALL MODELS
12 2M-60301-43 1 DIE CAST PLT LANG SATIN ALL MODELS
13 Q9-F6-145 1 OUTSIDE DOOR PANEL ALL MODELS
NI Q9-F6-423-2 1 ASSEMBLY DOOR SUB-MARINE FCOF-AT-480G, FCOFAT480SUB, FCOFATSL480M,
FCOFL-AT440G, FCOFLSL208VM, FCOFLSL240VM,
FCOFLSL440VM, FCOFLSL480VM
NI Q9-F6-423 1 ASSEMBLY DOOR FCOF-AT-208V/M, FCOF-AT-240V/M, FCOF-AT-440M,
FCOF-AT-480V/M, FCOFL-AT-208, FCOFL-AT-240,
FCOFL-AT-480, FCOFL-AT208M, FCOF-AT240M,
FCOFL-AT440M, FCOFL-AT480M

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
 1

16

3
15
4

5
6
14 7
8
13

11

12

10
9

Model:
FCOF-SUB Can Assembly
F6S Can Assembly
SK2291 Rev. - 7/30/07
PARTS LIST April 5, 2010, Rev B

Model No: FCOF & FCOFL Can Assembly
Commercial, Marine & Submarine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description

1 Q9-F6-102-5 1 SPOT CAN TOP SUB FCOFAT480SUB

2 Q9-F6-102-7 1 SPOT CAN REAR SUB FCOFAT480SUB
3 Q9-F6-113-1 1 VENT PIPE ASSY SUB FCOFAT480SUB
Q9-F6-113 1 VENT PIPE ASSEMBLY FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
4 2N-11090-09 1 ELMNT F6OVEN 208V 6KW FCOF 208M, 208V; FCOFL 208, 208M
2N-11090-10 1 ELMNT F6OVEN 240V 6KW FCOF 240M, 240V; FCOFL 240, 240M
2N-11090-11 1 ELMNT F6OVEN 480V 6KW FCOFAT480SUB; FCOF 440G, 440M, 480M, 480V,
480G; FCOFL 480, 440G, 440M, 480G, 480M
2N-11090-28 1 ELEMT F6OVEN 380V 6KW FCOFK-AT380M
5 Q9-F6-104-5 1 SPOT R/H CAN SIDE SUB FCOFAT480SUB
6 Q9-F6-159-2 1 CAN SIDE INSULATION SUB FCOFAT480SUB
2H-F6-159-1 1 INSULATION CAN SIDE UPPER FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
7 Q9-F6-252-1 1 R/H SIDE REAR INSULATION FCOFAT480SUB
2H-F6-252 1 INSULATION-SIDE R/H REAR FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
8 Q9-F6-188 1 MOTOR MNT ASY NO MTR SS FCOFAT480SUB
Q9-F6-189 1 MOTOR MOUNT ASSEMBLY NO FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
9 Q9-F6-159-2 1 CAN SIDE INSULATION SUB FCOFAT480SUB
2H-F6-159 1 INSULATION CAN SIDE LOWER FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
10 Q9-F6-251-1 1 R/H SIDE FRONT INSULATION FCOFAT480SUB
2H-F6-251 1 INSULATION-SIDE R/H FRONT FCOF 208M, 208V, 240M, 240V, 440G,440M,480M,
480V; FCOFL 208, 240, 480, 208M, 240M, 440G,
440M, 480G, 480M
11 Q9-F6-403 1 STAT HOLDER SPOTWELD ALL MODELS
12 Q9-F6-102-6 1 SPOT CAN BOTTOM SUB FCOFAT480SUB
13 2R-70602-03 1 CATCH DOOR MAGNET 3 PC ALL MODELS
14 2H-F6-158 1 CAN SIDE INSULATION ALL MODELS
15 Q9-F6-104-7 1 SPOT L/H CAN SIDE SUB FCOFAT480SUB
16 Q9-F6-405 1 BAFFLE SPOTWELD A/L FCOF-AT-208V/M, FCOF-AT-240V/M, FCOF-AT-440M,
FCOF-AT-480V/M, FCOFL-AT-208, FCOFL-AT-240,
FCOFL-AT-480, FCOFL-AT208M, FCOF-AT240M,
FCOFL-AT440M, FCOFL-AT480M
Q9-F6-405-1 1 BAFFLE SPOTWELD S/S FCOF-AT-480G, FCOFAT480SUB, FCOFATSL480M,
FCOFL-AT440G, FCOFLSL208VM, FCOFLSL240VM,
FCOFLSL440VM, FCOFLSL480VM

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
 1

15
3

2
14

13

12

2
11 6
10
9
12 11 8
7
Marine Application

RF21SM Controls

Model:
FCOF-AT & FCOFL-AT Controls Assembly
F6S-AT Controls Assembly SK2292 Rev. - 7/30/07
PARTS LIST October 4, 2012, Rev B

Model No: FCOF & FCOFL Controls Assembly
Commercial, Marine & Submarine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description
1 2E-30701-03 1 CONTC2POL35A208-240V50/60 ALL MODELS
2 Q9-F6-138 1 CONTROL SLIDE SPOTWELD ALL MODELS
3 2J-30801-01 1 TIMER MECHANICAL LONG ALL MODELS
4 2E-30303-06 1 SWT TOG ON-ON DPDT BLK ALL MODELS
5 Q9-70701-09 1 KNOB MANUAL TIMER, BLACK
Q9-70701-09-2 1 KNOB MANUAL TIMER, RED
6 2R-70701-25 1 KNOB DAMPER BLACK PLAIN ALL MODELS
7 Y9-70701-19 1 KNOB 450o D, BLACK ALL MODELS
Y9-70701-19-2 1 KNOB 450o D, RED
8 2E-30901-02 2 FUS HLDR FOR 15AMP FUSE ALL MODELS
9 2J-31601-01 2 PILOT LT 250V 6LEAD BLK ALL MODELS
10 2T-30402-27 1 STAT ADJ 450 DEG 48 PILOT ALL MODELS
11 Q9-F6-165 1 MARINE CIRCUIT BREAKER FCOFAT480 SUB, FCOF 440G & 480G, FCOFL 440G
& 480G
12 2E-31800-07 1 CB 2/10 AMP 2 POLE FCOFAT480 SUB, FCOF 440G & 480G, FCOFL 440G
& 480G
12 2E-31800-01 2 CB 250V50A 1 POLE CRLNGSW FCOFATSL208M
13 2E-31400-04 1 XFRMR 480/240VAC 100VA FCOFAT480SUB; FCOF 440M, 440G, 480V, 480M,
480G; FCOFL 440M, 440G, 480, 480M, 480G
14 2E-31800-04 1 CB 480V 50A 3 POLE FCOFAT480SUB; FCOF 440M, 440G, 480V, 480M,
480G; FCOFL 440M, 440G, 480, 480M, 480G
15 2E-30700-03 1 CONTC 3POLE 40A208-240VAC FCOFAT480SUB; FCOF 440M, 440G, 480V, 480M,
480G; FCOFL 440M, 440G, 480, 480M, 480G

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
 1

16 3
17
4
18
5

19

15 6

14
7

8
13
12

2
11
10

Model:
FCOF & FCOFL Motor Fan Assembly
F6S Motor Fan Assembly
SK2293 Rev. - 7/30/07
PARTS LIST April 5, 2010, Rev B

Model No: FCOF & FCOFL Motor Fan Assembly
Commercial, Marine & Submarine Full Size Economy Convection Oven

Key Part Qty

Number Number Per Description
1 2C-20104-18 4 SCRW HXHDCP 5/16-18X1-1/4 ALL MODELS
2 2C-20201-09 AR WSHR PLT 5/16 FLAT SAE ALL MODELS
3 2A-20503-01 4 5/16IDX27/640DX5/16LG STL ALL MODELS
4 2I-70801-06 4 RUBBER GROMMET 7/16 I.D. ALL MODELS
5 2U-30200-03 1 MTR 1/3HP 480V 3PH 60HZ FCOFAT480SUB; FCOF 440G, 440M, 480M, 480V;
FCOFL 480, 440G, 440M, 480G, 480M
2U-30200-60 1 MTR 1/3HP 380V 1PH 50HZ 2SP FCOFL-AT380M
5 2U-30200-12 1 MTR 1/3HP 115/208-240 1PH FCOF 208M, 208V, 240V, 240M; FCOFL 208, 208M,
240, 240M
6 Q9-F6-180 1 MOTOR MOUNT WELDMENT ALL MODELS
7 2H-F6-184 1 MOTOR INSULATION ALL MODELS
8 Q9-F6-186 1 MOTOR INSULATION RETAINER ALL MODELS
9 2C-20301-13 AR NUT HEX 1/4-20 PLTD ALL MODELS
10 2C-20301-06 4 NUT HEX 5/16-18 PLTD ALL MODELS
11 2C-20202-08 4 WSHR PLT 5/16 LOCK SPLIT ALL MODELS
12 2C-20306-02 4 AVK CAD 1/4-20 1ST GRP ALL MODELS
13 Q9-F6-185 4 BLOWER SPACER ALL MODELS
14 2C-20203-07 4 WASHER S/S 1/4 SAE FLAT FCOFAT480SUB; FCOF 440G, 480G; FCOFL 440G,
480G
14 2C-20201-07 4 WSHR FLT 1/4 SAE PLTD FCOF 208M, 208V, 240M, 240V, 440M,480M, 480V;
FCOFL 208, 240, 480, 208M, 240M, 440M, 480M
15 2C-20104-14 4 SCRW HXHD TAPBOLT ALL MODELS
16 2C-20103-06 4 SCRW SM PLT 6 X 3/8 PHL ALL MODELS
17 Q9-F6-406 1 WELD ORIFICE RING ALL MODELS
18 Q9-F6-187-1 1 BAFFLE MOUNTING PLATE SUB FCOFAT480SUB
Q9-F6-181 1 MOTOR MOUNT PLATE FCOF 208M, 208V, 240M, 240V, 440M, 440G, 480M,
480V, 480G; FCOFL 208, 240, 480, 208M, 240M,
440G, 440M, 480M, 480G
19 2U-71500-03 1 BLOWER WHEEL F-6 ALL MODELS

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1

INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.
STAR INTERNATIONAL HOLDINGS INC. COMPANY
Star - Holman - Lang - Wells - Bloomfield - Toastmaster
10 Sunnen Drive, St. Louis, MO 63143 U.S.A.
(314) 678-6303
www.star-mfg.com