Scribd
Upload
44 views

Ipv4 Packet Header: Lecture No6

This document summarizes key aspects of IPv4 packet headers and networking. It discusses: 1) The main fields in an IPv4 packet header, including version, DSCP, TTL, protocol, and source/destination IPv4 addresses. 2) Limitations of IPv4 including address depletion, routing table expansion, and lack of end-to-end connectivity. 3) Methods of sending IPv4 messages including unicast, broadcast, and multicast. It also briefly discusses host forwarding decisions and the role of the default gateway in routing traffic between local and remote networks.

Uploaded by

Group B
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
44 views

Ipv4 Packet Header: Lecture No6

This document summarizes key aspects of IPv4 packet headers and networking. It discusses: 1) The main fields in an IPv4 packet header, including version, DSCP, TTL, protocol, and source/destination IPv4 addresses. 2) Limitations of IPv4 including address depletion, routing table expansion, and lack of end-to-end connectivity. 3) Methods of sending IPv4 messages including unicast, broadcast, and multicast. It also briefly discusses host forwarding decisions and the role of the default gateway in routing traffic between local and remote networks.

Uploaded by

Group B
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Lecture No6 Computer Networks Asst.Lec.

Tareq Imad Ali

IPv4 Packet Header


An IPv4 packet header consists of fields containing important information about the
packet. These fields contain binary numbers which are examined by the Layer 3
process. The binary values of each field identify various settings of the IP packet.
Protocol header diagrams, which are read left to right, and top down, provide a visual
to refer to when discussing protocol fields. The IP protocol header diagram in the
figure (31) identifies the fields of an IPv4 packet. Significant fields in the IPv4
header include:
- Version - Contains a 4-bit binary value set to 0100 that identifies this as an IP
version 4 packet.
- Differentiated Services or DiffServ (DS) - Formerly called the Type of
Service (ToS) field, the DS field is an 8-bit field used to determine the priority
of each packet. The six most significant bits of the DiffServ field is the
Differentiated Services Code Point (DSCP) and the last two bits are the
Explicit Congestion Notification (ECN) bits.
- Time-to-Live (TTL) - Contains an 8-bit binary value that is used to limit the
lifetime of a packet. The packet sender sets the initial TTL value, and it is
decreased by one each time the packet is processed by a router. If the TTL
field decrements to zero, the router discards the packet and sends an Internet
Control Message Protocol (ICMP) Time Exceeded message to the source IP
address.
- Protocol - Field is used to identify the next level protocol. This 8-bit binary
value indicates the data payload type that the packet is carrying, which enables
the network layer to pass the data to the appropriate upper-layer protocol.
Common values include ICMP (1), TCP (6), and UDP (17).
- Source IPv4 Address - Contains a 32-bit binary value that represents the
source IPv4 address of the packet. The source IPv4 address is always a unicast
address.
- Destination IPv4 Address - Contains a 32-bit binary value that represents the
destination IPv4 address of the packet. The destination IPv4 address is a
unicast, multicast, or broadcast address.
Lecture No6 Computer Networks Asst.Lec. Tareq Imad Ali

Fig.31. IP protocol header

The two most commonly referenced fields are the source and destination IP
addresses. These fields identify where the packet is coming from and where it is
going. Typically, these addresses do not change while travelling from the source
to the destination The Internet Header Length (IHL), Total Length, and Header
Checksum fields are used to identify and validate the packet.
Limitations of IPv4
Through the years, IPv4 has been updated to address new challenges. However, even
with changes, IPv4 still has three major issues:
- IP address depletion - IPv4 has a limited number of unique public IPv4
addresses available. Although there are approximately 4 billion IPv4
addresses, the increasing number of new IP-enabled devices, always-on
connections, and the potential growth of less-developed regions have
increased the need for more addresses.
- Internet routing table expansion - A routing table is used by routers to make
best path determinations. As the number of servers connected to the Internet
Lecture No6 Computer Networks Asst.Lec. Tareq Imad Ali

increases, so too does the number of network routes. These IPv4 routes
consume a great deal of memory and processor resources on Internet routers.
- Lack of end-to-end connectivity - Network Address Translation (NAT) is a
technology commonly implemented within IPv4 networks. NAT provides a
way for multiple devices to share a single public IPv4 address. However,
because the public IPv4 address is shared, the IPv4 address of an internal
network host is hidden. This can be problematic for technologies that require
end-to-end connectivity.
IPv4 Message Communication
We actually have three different methods of sending IPv4 messages over
computer networks as shown in the figure (32). Those methods are unicast,
multicast and broadcast.
- Unicast Message: - When using unicast method, one device will send the
message to exactly one destination device. If some device needs to send a
message to multiple devices, it will have to send multiple unicast messages,
each message addressed to a specific device. So, the sender has to send a
separate message to each destination device, and to do that it has to know the
exact IP address of each destination device. Remember that in unicasting, each
packet is destined for only one device.
- Broadcast Message: - The second method of sending messages is called the
broadcasting. Broadcast is a packet that’s sent to all devices on specific
network. The destination address in the packet is the special broadcast
address. If the packet has a broadcast address, all devices that receive that
message will process it. So, all devices on the same network segment will see
the same message. Another thing to remember is that routers don’t forward
broadcast messages. The router will receive the broadcast traffic, but it will
not forward it through the router.
- Multicast Message - :Multicasting identifies logical groups of computers. A
single message can then be sent to the group. Multicasting uses the Internet
Group Management Protocol (IGMP) to identify groups and group members.
Routers will also use IGMP to send messages to subnets that have group
members. Each host on the network can belong to multiple multicast groups.
Hosts can join or leave groups at any time. Multicast groups are identified by
Lecture No6 Computer Networks Asst.Lec. Tareq Imad Ali

special IP addresses between the range of 224.0.0.0 and 239.255.255.255.


Each group is assigned its own address.
Addresses within the 224.0.0.0 range are reserved for local subnet communications.

Fig.32. unicast, broadcast and multicast messages


Host Forwarding Decision
Another role of the network layer is to direct packets between hosts. A host can send
a packet to:
- Itself: - A host can ping itself by sending a packet to a special IPv4 address of
127.0.0.1, which is referred to as the loopback interface. Pinging the
loopback interface tests the TCP/IP protocol stack on the host.
- Local host: - This is a host on the same local network as the sending host.
The hosts share the same network address.
- Remote host: - This is a host on a remote network. The hosts do not share the
same network address.
Whether a packet is destined for a local host or a remote host is determined by the
IPv4 address and subnet mask combination of the source (or sending) device
compared to the IPv4 address and subnet mask of the destination device. In a home
or business network, you may have several wired and wireless devices
interconnected together using an intermediate device, such as a LAN switch and/or
a wireless access point (WAP). This intermediate device provides interconnections
between local hosts on the local network. Local hosts can reach each other and share
information without the need for any additional devices. If a host is sending a packet
to a device that is configured with the same IP network as the host device, the packet
is simply forwarded out of the host interface, through the intermediate device, and
Lecture No6 Computer Networks Asst.Lec. Tareq Imad Ali

to the destination device directly. Of course, in most situations we want our devices
to be able to connect outside the local
Network segment, such as out to other homes, businesses, and the Internet. Devices
that are outside the local network segment are known as remote hosts. When a source
device sends a packet to a remote destination device, then the help of routers and
routing is needed. Routing is the process of identifying the best path to a
destination. The router connected to the local network segment is referred to as the
default gateway. Figure (33) show the types of destinations.

Fig.33. Types of destinations

Default Gateway
The default gateway is the network device that can route traffic to other networks. It
is the router that can route traffic out of the local network. If you use the analogy
that a network is like a room, then the default gateway is like a doorway. If you want
to get to another room or network you need to find the doorway. Alternatively, a PC
or computer that does not know the IP address of the default gateway is like a person,
in a room, that does not know where the doorway is. They can talk to other people
in the room or network, but if they do not know the default gateway address, or there
is no default gateway, then there is no way out. So, the functions of the default
gateway are: -
Lecture No6 Computer Networks Asst.Lec. Tareq Imad Ali

1- Routes traffic to another network.


2- Configure with a local IP address in the same address range as other hosts in
the same network side.
3- Take data in and forward data out.
A host's routing table will typically include a default gateway. The host receives the
IPv4 address of the default gateway either dynamically from Dynamic Host
Configuration Protocol (DHCP) or configured manually. In the figure (34), PC1 and
PC2 are configured with the default gateway’s IPv4 address of 192.168.10.1. Having
a default gateway configured creates a default route in the routing table of the PC. A
default route is the route or pathway your computer will take when it tries to
contact a remote network.
The default route is derived from the default gateway configuration and is placed in
the host computer’s routing table. Both PC1 and PC2 will have a default route to
send all traffic destined to remote networks to R1.

Fig.34. Host Default Gateway

You might also like