Scribd
Upload
37 views

Test 1

1. One revolution of a metric micrometer thimble produces 0.01mm of linear movement. 2. The pitch of a metric micrometer screw thread is 0.5mm. 3. The cutting angle of a drill is 59 degrees.

Uploaded by

gunapalshetty
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
37 views

Test 1

1. One revolution of a metric micrometer thimble produces 0.01mm of linear movement. 2. The pitch of a metric micrometer screw thread is 0.5mm. 3. The cutting angle of a drill is 59 degrees.

Uploaded by

gunapalshetty
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

1.

One revolution of the thimble of the Metric micrometer produces a linear


movement of the spindle of
a) 0.05mm
b) 0.01mm
# c) 0.50mm

2. The pitch of a metric micrometer screw thread is


# a) 0.5 mm
b) 0.01 mm
c) 1.0 mm

3. What is a drill cutting angle?


# a) 59o
b) 12o - 15o
c) 125o - 135o

4. What is the cutting angle of a drill?


a) 130o
# b) 59o
c) 12

5. The normal drill angles are


a) cutting angle 130o, web angle 59o and clearance angle 12o
# b) cutting angle 59o, web angle 130o and clearance angle 12o
c) cutting angle 12o, web angle 130o and clearance angle 130o

6. Reamers are used to


a) drill accurate holes
# b) enlarge holes to accurate dimensions
c) to make holes oversize

7. The pitch of a hacksaw blade is


a) its length
b) the number of teeth on the blade
# c) the number of teeth per inch

8. The Thimble on an metric micrometer is divided into


a) 25 equal divisions
# b) 50 equal divisions
c) 40 equal divisions
9. The metric micrometer reading shown is

a) 13.87 mm
# b) 13.37 mm
c) 10.337 mm

10. Centre punches are made of


a) high carbon steel hardened and tempered
b) case hardened mild steel
# c) high carbon steel with the tip hardened and tempered

11. How are pin punches classified?


a) By overall length and type
b) By length and diameter of the small end
# c) By type and diameter of the small end

12. How are spring dividers classified?


a) The diameter of the largest circle that can be scribed
b) The diameter of a circle scribed with the legs at 600
# c) The length of the legs

13. Which is correct concerning the use of a file?


a) Apply pressure on the forward stroke, only, except when filing very soft
metals such as lead or aluminium
# b) A smoother finish can be obtained by using a double-cut file than by using
a single-cut file
c) The terms `double-cut` and `second-cut` have the same meaning in
reference to files

14. Why is the Vee cut in the base of a scribing block?


a) to reduce the contact area with the marking off table and reduce friction
# b) to trap any dirt that may be adhering to the surface of the marking off table
c) to allow the scribing block to be used on the edge of the marking off table
15. Die is used to
a) form external threads
# b) clean up damaged threads
c) form internal threads

16. The name given to the moving scale on the Vernier caliper is
a) the cursor
b) the main scale
# c) the vernier scale

17. What does the cut of a file refer to


a) Number of teeth per inch
# b) Arrangement of the teeth
c) Grade

18. How are files classified?


a) By length, grade and material
# b) By length, grade, cut and cross-section
c) By length, grade, cut, section and material

19. Hammers are classified by


a) shape of head and length of shaft
b) weight and length of shaft
# c) weight and type of head

20. What does the term 'second cut' indicate as applied to hand files?
# a) The grade of the file
b) A reconditioned file
c) The section of the file

21. The teeth on a hacksaw blade


# a) should point away from the handle
b) should point towards the handle
c) does not matter which way they point

22. What is the clearance angle on a twist drill


# a) 12 degrees
b) 59 degrees
c) 130 degrees

23. Surface Plates are used


# a) for marking out work and testing flat surfaces
b) for filing flat surfaces
c) only on surface tables

24. Draw filing produces


a) a course finish
# b) a fine finish
c) a mottled finish

25. A safe edge of a file is used


a) against a rough unfinished surface
# b) against a finished surface
c) to give a fine polished finish to a smooth surface

26. Scribers are used to


# a) mark guide lines on material
b) produce an accurate finish
c) make centre pop marks for drilling

27. The main scale of a Metric micrometer is calibrated in


a) millimetres
# b) millimetres and half millimetres
c) micro-meters

28. for a drill to cut properly it is essential that the point angle be the same on
each side, for general use the angle is
a) 130o
# b) 59o
c) 12o

29. When using a hand file correctly, the downward pressure should be used only
a) on a return stroke
b) on the forward and return stroke
# c) on the forward stroke

30. A drill is identified by


a) Letters from A to Z
b) Numbers from 1 to 80
# c) Both a and b

31. Center Punch is used to


# a) mark guide lines on material
b) produce an accurate finish
c) make centre pop marks for drilling
31. One revolution of the thimble of the English micrometer produces a linear
movement of the spindle of
a) 0.040"
b) 0.001"
c) 0.025 #

32. When drilling stainless steel, the drill used should have an included angle of
a) 90 degrees and turn at a low speed
b) 118 degrees and turn at a high speed
c) 140 degrees and turn at a low speed #

33. The purpose of a taper tap is to


a) form a tapered thread
b) produce a fine thread
c) start a thread #

.?Which of the following is the most appropriate filing technique.34


. a)Pressure backwards, relieve pressure forward
.b)Even pressure forward and backwards .
.b)Pressure forwards, relieve pressure backwards .

You might also like