Sandvik QJ Warnings - DP600 V1.08 MC88 V1.
07
QJ – Warning Codes (Blue)
Code 1
Description Main Conveyor Speed Low
Criteria Main conveyor speed is less than ‘Main Conveyor Speed Warning’ Set
Point
Action Feeder stopped
Troubleshooting Ensure belt speed is above the set point
Ensure speed wheel signal is being received by controller,
investigate speed wheel circuit
Code 2
Description Side Conveyor Speed Low
Criteria Side conveyor speed is less than ‘Side Conveyor Speed Warning’ Set Point
Action Feeder Stopped
Troubleshooting Ensure belt speed is above the set point
Ensure speed wheel signal is being received by controller,
investigate speed wheel circuit
Code 6
Description Main Conveyor Pull Stop
Criteria Main conveyor pull stop signal is low
Action Main conveyor and feeder stopped
Troubleshooting Ensure pull stop is reset,
Investigate pull stop circuit, ensure input to controller is high
1
Sandvik QJ Warnings - DP600 V1.08 MC88 V1.07
Code 10
Description Hydraulic Oil Temperature High
Criteria Hydraulic oil temperature is above the warning level
Action Feeder Stopped
Troubleshooting Ensure Oil Temperature is lower than the warning level
Investigate oil temperature circuit,
check sensor impedance,
check 5v supply to sensor
Code 12
Description Track Radio Joy Stick Fault
Fault Criteria Joystick fault message received from radio received
Action Prevents radio tracking / Radio functions
Troubleshooting Ensure radio transmitter battery is charged,
Ensure radio transmitter is in serviceable condition
Code 13
Description Radio Unavailable
Criteria No valid CAN messages received from radio receiver
Action Prevents radio tracking / Radio functions
Troubleshooting Ensure receiver is powered and connected
Investigate CAN connection
Code 14
Description No Radio Signal
Criteria Low radio signal message received from radio receiver
Action Prevents radio tracking / Radio functions
Troubleshooting Ensure radio battery is charged
Ensure handset is live – indicated by flashing green led
Ensure antenna is connected and in good condition
2
Sandvik QJ Warnings - DP600 V1.08 MC88 V1.07
Code 15
Description Dog Lead Fault
Criteria Forward / Reverse signals form tracking handset out of range
Action Prevents manual tracking
Troubleshooting Ensure signals are correct,
Investigate tracking handset circuit
Code 18
Description Side Conveyor Pull Stop
Criteria Side conveyor pull stop input is low
Action Feeder stopped / Conveyor stopped
Troubleshooting Ensure pull stop is reset
Ensure pull stop input is high
Investigate pull stop circuit
Code 20
Description Low Urea Level
Fault Criteria Urea level is below the ‘Urea Level Warning’ set point
Action Feeder stopped
Troubleshooting Ensure Urea level is above the minimum level
Code 21
Description Toggle Overcharging
Criteria Toggle charge output has remain on for an extended period of time
Action Non - reference only
Troubleshooting Investigate toggle changing circuit
3
Sandvik QJ Warnings - DP600 V1.08 MC88 V1.07
Code 22
Description Warning High Load
Criteria Crusher drive pressure is above ‘Drive pressure warning’ set point for
‘Drive pressure warning time’ set point
Action Feeder stopped
Troubleshooting Ensure drive pressure remains below the set point
Investigate the crusher pressure transducer circuit
Code 23
Description Fuel Level Low
Criteria Fuel level is less than the ‘Fuel level warning’ set point
Action Feeder stopped
Troubleshooting Ensure fuel level is above the set point,
Investigate the fuel level sensor circuit
Code 24
Description High Soot Load
Criteria DPF soot load is above the ‘Soot load warning’ set point
Action Feeder stopped
Troubleshooting Ensure soot load is below the warning level,
Investigate other active engine alarms that may prevent regeneration,
Consult CAT
Code 26
Description Air filter Restriction
Criteria Engine air filter restriction switch is closed
Action Feeder Stopped
Troubleshooting Ensure air filter restriction switch is reset
4
Sandvik QJ Warnings - DP600 V1.08 MC88 V1.07
Code 27
Description Greaser Fault
Criteria Auto lubrication fault input is high
Action Feeder Stopped
Troubleshooting Ensure auto lubrication fault is reset
Investigate auto lubrication system / circuit
Code 28
Description Low Crusher Speed
Criteria Crusher speed is below ‘Crusher Minimum Speed’ set point
Action Feeder stopped
Troubleshooting Ensure crusher speed remains above warning level
Investigate crusher speed sensor circuit
Code 29
Description Main Conveyor Output Fault
Criteria Main conveyor solenoid output is shorted to ground
Action Non - Reference only
Troubleshooting Investigate main conveyor solenoid circuit
Code 30
Description Crusher Forward Output Fault
Criteria Crusher forward output is shorted to ground
Action Non – Reference only
Troubleshooting Investigate crusher forwards output circuit
5
Sandvik QJ Warnings - DP600 V1.08 MC88 V1.07
Code 31
Description Crusher Reverse Output Fault
Criteria Crusher reverse output is shorted to ground
Action Non – Reference only
Troubleshooting Investigate crusher reverse output circuit
Code 32
Description Side Conveyor Output Fault
Criteria Side Conveyor output is shorted to ground
Action Non – Reference only
Troubleshooting Investigate side conveyor output circuit
Code 34
Description Fuel Level Sender Unavailable
Criteria Fuel level sensor input out of range
Action Non – Reference only
Troubleshooting Investigate fuel level sender circuit,
Ensure impedance is between 10 & 180 ohms
Code 35
Description Tail Conveyor Material Level High
Criteria Main conveyor level sensor signal is below the desired level
Action Feeder stopped
Troubleshooting Ensure level of material is below set point,
Investigate main conveyor level sensor circuit
