https://www.phoenixcontact.
com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Termination Carrier for redundantly connecting 32 MACX Analog Ex i signal conditioners with double output to
analog input cards of the HIMA HIMax controller, via one C96 connector, 96-pos. Suitable for the HIMax X-AI
32 01 card, with HART multiplexer connection
Your advantages
Mechanically decoupled, passive PCB
Robust aluminum profile with integrated DIN rail
Side parts with integrated end clamps
Interface for connection to HART multiplexer via IDC/FLK male strip
Simple or redundant supply, decoupled from diode, protected against polarity reversal
The feed-in/fault signaling module is supplied as standard and does not have to be ordered separately
Cable sets for signal connection are supplied as standard and do not have to be ordered separately
Key Commercial Data
Packing unit 1
GTIN
GTIN 4055626327617
Custom tariff number 85366990
Technical data
Note
EMC: class A product, see manufacturer's declaration in the download
Utilization restriction
area
General
Nominal voltage UN < 50 V DC (Per signal/channel)
Max. permissible current 1 A (Signal/channel)
Degree of protection IP20
Supply
Designation Device supply
06/03/2019 Page 1 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Technical data
Supply
Input voltage 24 V DC
Input voltage range 19.2 V DC ... 30 V DC
Input current ≤2A
Redundant supply yes, decoupled from diodes
Polarization and surge protection Yes
Output name Switching output
Contact type 1 N/C contact (alarm = open)
Maximum switching voltage 30 V DC (2 A)
Fuse 2x 3.15 A Slow-blow (exchangeable)
Status display 2x green LEDs (PWR1 and PWR2)
Connection 1
Connection name Power supply
Connection method Screw connection
Stripping length 7 mm
Number of connections 1
Number of positions 6
Conductor cross section solid 0.75 mm² ... 2.5 mm²
Conductor cross section flexible 0.75 mm² ... 2.5 mm²
Conductor cross section AWG 18 ... 14
Connection 2
Connection name Controller level
Connection in acc. with standard IEC 60603-2
Connection method Pin strip
Type C
Number of connections 1
Number of positions 96
Connection 3
Connection method IDC/FLK pin strip
Number of connections 1
Number of positions 14
Ambient conditions
Ambient temperature (operation) -20 °C ... 60 °C
Ambient temperature (storage/transport) -40 °C ... 80 °C
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
Shock 15g, according to IEC 60068-2-27
Vibration (operation) 2g, according to IEC 60068-2-6
Maximum altitude ≤ 2000 m
Dimensions
06/03/2019 Page 2 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Technical data
Dimensions
Width 448 mm
Height 170 mm
Depth 160 mm
Standards and Regulations
Designation Air clearances and creepage distances
Standards/regulations DIN EN 50178
Rated insulation voltage 30 V
Rated surge voltage 0.5 kV
Insulation Basic insulation
Degree of pollution 2
Overvoltage category II
Designation Directive 2014/35/EU (EMV)
Standards/regulations EN 6100-6-2
EN 6100-6-4
Designation Directive 2014/35/EU (EMV)
Standards/regulations EN 60079-0
EN 60079-7
EN 60079-11
Shock 15g, according to IEC 60068-2-27
Vibration (operation) 2g, according to IEC 60068-2-6
ATEX II 3 G Ex ec IIC T4 Gc X
UL, USA/Canada Class I, Div. 2, Groups A, B, C, D T4
Class I, Zone 2, Group IIC
Environmental Product Compliance
Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”,
Category “Manufacturer's declaration”
Drawings
06/03/2019 Page 3 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Block diagram
X51 X20
1
Alarm
2
F1
3 (+) Power in
TC-MACX-MCR-PTB
PW1
4 (-)
V-
X52
Faultsignal
F2
5 (+)
V+
PW2
6 (-)
PWR
V+
V-
HART
X1B
ME T-BUS HART X1A
active (3-1-1)
4.1 AI1A+
3.1 X101 100Ω
b32
CH1 4.2 AI1A-
3.2 CH1A
AI1B+
2.1
AI1B-
2.2 CH1B 1+
1-
X-AI
4.1 3.1 AInA+ X1nn 32 01
CHn 4.2 3.2 AInA- CHnA
2.1 AInB+ n+
2.2 AInB- CHnB 2nd
n-
HART DCS
4.1 3.1AI32A+ X132 100Ω
b1
CH32 4.2 3.2AI32A- CH32A
2.1AI32B+
32+
2.2AI32B- Ch32B
32-
2904674 AI- a25..
a32
„31322122"
HART
a1
Run
a2 X1B1
a3 n=1..16
Field
a4 X1B2
n=17..32
HART HART-
X11 MUX
CH1..32
PWR
X-AI 32 01
Articles in set
Power and error message module - TC-MACX-MCR-PTB - 2904673
Power and fault signaling module with screw connection, only for use on the Termination Carrier, excluding
corresponding DIN rail bus connector
Cable set - TC-C-PTB3-SC-SET1 - 2905216
Cable set for TC-MACX-MCR-PTB power and fault signaling module (Order No. 2904673), for use on the
Termination Carrier for signal conditioners from the MACX Analog Ex series.
Cable set - TC-C-MAX2-SC-31320000 - 2902425
Cable set for signal transmission on the Termination Carrier for modules from the MACX Analog Ex series.
Connection of terminal points 3.1 and 3.2 (signal transmission) to the signal PCB.
06/03/2019 Page 4 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Articles in set
DIN rail bus connectors - ME 17,5 TBUS 1,5/ 5-ST-3,81 GN - 2709561
DIN rail connector for DIN rail mounting. Universal for TBUS housing. Gold-plated contacts, 5-pos.
DIN rail bus connectors - ME 6,2 TBUS-2 1,5/5-ST-3,81 GN - 2869728
DIN rail connector for DIN rail mounting. Universal for TBUS housing. Gold-plated contacts, 5-pos.
Classifications
eCl@ss
eCl@ss 4.0 27250313
eCl@ss 4.1 27250313
eCl@ss 5.0 27250313
eCl@ss 5.1 27250313
eCl@ss 7.0 27141152
eCl@ss 8.0 27141152
eCl@ss 9.0 27141152
ETIM
ETIM 4.0 EC002780
ETIM 5.0 EC002780
ETIM 6.0 EC002780
Approvals
Approvals
Approvals
UL Listed / cUL Listed / cULus Listed
Ex Approvals
UL Listed / cUL Listed / ATEX / cULus Listed
06/03/2019 Page 5 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Approvals
Approval details
UL Listed
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 330267
cUL Listed
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 330267
cULus Listed
Accessories
Accessories
Repeater power supplies
Repeater power supply - MACX MCR-EX-SL-RPSSI-2I - 2865366
Ex i measuring transducer power supply and input signal conditioner, HART-transparent. Transfers supplied or active
0/4…20 mA electrically isolated signals from the Ex area to two loads in the safe area. 4-way electrical isolation,
screw connection, SIL, PL.
Repeater power supply - MACX MCR-EX-SL-RPSSI-2I-SP - 2924236
Ex i measuring transducer power supply and input signal conditioner, HART-transparent. Transfers supplied or active
0/4…20 mA electrical isolation signals from the Ex area to two loads in the safe area. 4-way electrical isolation, Push-
in connection, SIL, PL.
Repeater power supply - MACX MCR-SL-RPSSI-2I - 2924825
Measuring transducer repeater power supply and input signal conditioner, HART-transparent. Transmits supplied or
active 0/4…20 mA electrically isolated signals from the field to two loads. 4-way electrical isolation, screw connection,
SIL, PL.
Additional products
06/03/2019 Page 6 / 7
https://www.phoenixcontact.com/sg/products/2908732
Module carrier - TC-XC96-AI32-EX2-PRS-HIMAX01 - 2908732
Accessories
Label, highly flexible - EMLF (108XE)R - 0800549
Label, highly flexible, Roll, white, unlabeled, can be labeled with: THERMOMARK ROLLMASTER 300/600,
THERMOMARK X1.2, THERMOMARK ROLL X1, THERMOMARK ROLL 2.0, THERMOMARK ROLL, mounting type:
adhesive, lettering field size: 108 x 48000 mm
Zack Marker strip, flat - ZBF 15:UNBEDRUCKT - 0811202
Zack Marker strip, flat, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into flat marker groove, for terminal block width: 15 mm, lettering field size: 15 x 5.2 mm
Phoenix Contact 2019 © - all rights reserved
http://www.phoenixcontact.com
06/03/2019 Page 7 / 7
